Search NASA⌕ Search

SEARCH · Search NASA

Results for “rolling degradation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Wind-tunnel investigation of the flight characteristics of a canard general-aviation airplane configuration

A 0.36-scale model of a canard general-aviation airplane with a single pusher propeller and winglets was tested in the Langley 30- by 60-Foot Wind Tunnel to determine the static and dynamic stability and control and free-flight behavior of the configuration. Model variables made testing of the model possible with the canard in high and low positions, with increased winglet area, with outboard wing leading-edge droop, with fuselage-mounted vertical fin and rudder, with enlarged rudders, with dual deflecting rudders, and with ailerons mounted closer to the wing tips. The basic model exhibited generally good longitudinal and lateral stability and control characteristics. The removal of an outboard leading-edge droop degraded roll damping and produced lightly damped roll (wing rock) oscillations. In general, the model exhibited very stable dihedral effect but weak directional stability. Rudder and aileron control power were sufficiently adequate for control of most flight conditions, but appeared to be relatively weak for maneuvering compared with those of more conventionally configured models.

Satran, D. R.↗
NASA NTRS1998

Tribometer for Lubrication Studies in Vacuum

The NASA Lewis Research Center has developed a new way to evaluate the liquid lubricants used in ball bearings in space mechanisms. For this evaluation, a liquid lubricant is exercised in the rolling contact vacuum tribometer shown in the photo. This tribometer, which is essentially a thrust bearing with three balls and flat races, has contact stresses similar to those in a typical preloaded, angular contact ball bearing. The rotating top plate drives the balls in an outward-winding spiral orbit instead of a circular path. Upon contact with the "guide plate," the balls are forced back to their initial smaller orbit radius; they then repeat this spiral orbit thousands of times. The orbit rate of the balls is low enough, 2 to 5 rpm, to allow the system to operate in the boundary lubrication regime that is most stressful to the liquid lubricant. This system can determine the friction coefficient, lubricant lifetime, and species evolved from the liquid lubricant by tribodegradation. The lifetime of the lubricant charge is only few micrograms, which is "used up" by degradation during rolling. The friction increases when the lubricant is exhausted. The species evolved by the degrading lubricant are determined by a quadrupole residual gas analyzer that directly views the rotating elements. The flat races (plates) and 0.5-in.-diameter balls are of a configuration and size that permit easy post-test examination by optical and electron microscopy and the full suite of modern surface and thin-film chemical analytical techniques, including infrared and Raman microspectroscopy and x-ray photoelectron spectroscopy. In addition, the simple sphere-on-a-flat-plate geometry allows an easy analysis of the contact stresses at all parts of the ball orbit and an understanding of the frictional energy losses to the lubricant. The analysis showed that when the ball contacts the guide plate, gross sliding occurs between the ball and rotating upper plate as the ball forced back to a smaller orbit radius. The friction force due to gross sliding is sensed by the piezoelectric force transducer behind the guide plate and furnishes the coefficient of friction for the system. This tribometer has been used to determine the relative lifetimes of Fomblin Z-25, a lubricant often used in space mechanisms, as a function of the material of the plates against which it was run. The balls were 440C steel in all cases; the plate materials were aluminum, chromium (Cr), 440C steel (17 wt % Cr), and 4150 steel (1 wt % Cr). As shown in the bar graph, the lifetime is greatest for the plate material with least chromium, thus implicating chromium as a tribochemically active element attacking Fomblin Z-25.

Pepper, Stephen V.↗
NASA NTRS1981

Analysis of augmented aircraft flying qualities through application of the Neal-Smith criterion

The Neal-Smith criterion is examined for possible applications in the evaluation of augmented fighter aircraft flying qualities. Longitudinal and lateral flying qualities are addressed. Based on the application of several longitudinal flying qualities data bases, revisions are proposed to the original criterion. Examples are given which show the revised criterion to be a good discriminator of pitch flying qualities. Initial results of lateral flying qualities evaluation through application of the Neal-Smith criterion are poor. Lateral aircraft configurations whose flying qualities are degraded by roll ratcheting effects map into the Level 1 region of the criterion. A third dimension of the criterion for flying qualities specification is evident. Additional criteria are proposed to incorporate this dimension into the criterion structure for flying qualities analysis.

Bailey, R. E.↗
NASA NTRS1986

Full-scale ground effects of twin impinging jets beneath a subsonic tactical V/STOL aircraft

This paper presents a summary of an analysis of flow field characteristics about a large scale twin-tilt-nacelle V/STOL aircraft in close proximity to the ground. The analysis uses experimental data in the form of measurements of pressure distributions on the ground beneath the aircraft and on the undersurface of the aircraft's fuselage. The integrals of these distributions are compared with forces measured directly, for both the total model and isolated nacelles, (i.e., net thrust). The handling qualities of the vehicle were found to be influenced by flow field characteristic features, not present in simpler models. Lift increases and significant degradation in roll control occur at low heights for fuselage strake deflections of 30 degrees or more. Reductions in control effectiveness about the other axes were also observed.

Dudley, Michael R.↗
NASA NTRS1985

In-flight evaluation of pure time delays in pitch and roll

An in-flight investigation of the effect of pure time delays in pitch and roll was undertaken. The evaluation tasks consisted of low lift-to-drag-ratio landings of various levels of difficulty and formation flying. The results indicate that the effect of time delay is strongly dependent on the task. In the pitch axis, in calm air, spot landings from a lateral offset were most strongly influenced by time delay. In the roll axis, in calm air, formation flying was most strongly influenced by time delay. However, when landings were made in turbulence, flying qualities in pitch were only slightly degraded, whereas in roll they were severely degraded.

Berry, D. T.↗
NASA NTRS1985

In-flight evaluation of pure time delays in pitch and roll

An in-flight investigation of the effect of pure time delays in pitch and roll was undertaken. The evaluation tasks consisted of low lift-to-drag-ratio landings of various levels of difficulty and formation flying. The results indicate that the effect of time delay is strongly dependent on the task. In the pitch axis, in calm air, spot landings from a lateral offset were most strongly influenced by time delay. In the roll axis, in calm air, formation flying was most strongly influenced by time delay. However, when landings were made in turbulence, flying qualities in pitch were only slightly degraded, whereas in roll they were severely degraded.

Berry, D. T.↗
NASA NTRS1984

A preliminary look at the effects of coupled lateral modes on aircraft handling qualities

Analytic and six-degree-of-freedom motion base simulator studies have been conducted to better understand how the coupled roll-spiral and coupled roll-aileron actuator modes affect aircraft handling qualities. The results reported herein are preliminary and are subject to change until other aircraft and several more data points can be examined. The results obtained thus far indicate that when the roll-spiral coupled mode is brought about by unusual values of an aircraft's stability and control derivatives, the lateral-directional handling qualities will invariably be degraded. However, when the roll spiral coupling is brought about by a roll-rate command/roll-attitude hold stability and control augmentation system (SCAS), the requirements for satisfactory handling qualities can be correlated to the natural frequency and the damping of the coupled mode. Satisfactory handling qualities were also achieved when the lateral SCAS brought about a coupling of the roll mode with the aileron actuator mode. In this case, the pilot ratings indicate that the handling qualities may be correlated to the natural frequency of the coupled roll-aileron mode.

Ruflin, S. J.↗
NASA NTRS2013

A Model to Assess the Risk of Ice Accretion Due to Ice Crystal Ingestion in a Turbofan Engine and its Effects on Performance

The occurrence of ice accretion within commercial high bypass aircraft turbine engines has been reported under certain atmospheric conditions. Engine anomalies have taken place at high altitudes that were attributed to ice crystal ingestion, partially melting, and ice accretion on the compression system components. The result was one or more of the following anomalies: degraded engine performance, engine roll back, compressor surge and stall, and flameout of the combustor. The main focus of this research is the development of a computational tool that can estimate whether there is a risk of ice accretion by tracking key parameters through the compression system blade rows at all engine operating points within the flight trajectory. The tool has an engine system thermodynamic cycle code, coupled with a compressor flow analysis code, and an ice particle melt code that has the capability of determining the rate of sublimation, melting, and evaporation through the compressor blade rows. Assumptions are made to predict the complex physics involved in engine icing. Specifically, the code does not directly estimate ice accretion and does not have models for particle breakup or erosion. Two key parameters have been suggested as conditions that must be met at the same location for ice accretion to occur: the local wet-bulb temperature to be near freezing or below and the local melt ratio must be above 10%. These parameters were deduced from analyzing laboratory icing test data and are the criteria used to predict the possibility of ice accretion within an engine including the specific blade row where it could occur. Once the possibility of accretion is determined from these parameters, the degree of blockage due to ice accretion on the local stator vane can be estimated from an empirical model of ice growth rate and time spent at that operating point in the flight trajectory. The computational tool can be used to assess specific turbine engines to their susceptibility to ice accretion in an ice crystal environment.

Jorgenson, Philip C. E.↗
NASA NTRS1989

The application of electrochemical impedance spectroscopy for characterizing the degradation of Ni(OH)2/NiOOH electrodes

Electrochemical impedance spectra of rolled and bonded and sintered porous nickel battery electrodes were recorded periodically during charge/discharge cycling in concentrated KOH solution at various temperatures. A transmission line model (TLM) was adopted to represent the impedance of the porous electrodes, and various model parameters were adjusted in a curve fitting routine to reproduce the experimental impedances. Degradation processes for rolled and bonded electrodes were deduced from changes in model parameters with electrode cycling time. In developing the TLM, impedance spectra of planar (non-porous) electrodes were used to represent the pore wall and backing plate interfacial impedances. These data were measured over a range of potentials and temperatures, and an equivalent circuit model was adopted to represent the planar electrode data. Cyclic voltammetry was used to study the characteristics of the oxygen evolution reaction on planar nickel electrodes during charging, since oxygen evolution can affect battery electrode charging efficiency and ultimately electrode cycle life if the overpotential for oxygen evolution is sufficiently low. Transmission line modeling results suggest that porous rolled and bonded nickel electrodes undergo restructuring during charge/discharge cycling prior to failure.

Macdonald, D. D.↗
NASA NTRS1974

Skylab program. Earth resources experiment package. Sensor performance report. Volume 7 (S190B): SL2, SL3 and SL4 evaluations

The S190B Earth Terrain Camera (ETC) operated acceptably for all of its scheduled EREP passes throughout the SL2 mission. The crew reported no problems in unstowing the camera, changing filters, installing the ETC window in the SAL, or installing the camera onto the window. The ETC was operated for a total of seven times with no failures. The clock on the ETC was checked on DOY 170 (June 19, 1973) and was found to be 30 min. and 58 sec. slower than GMT. The change in time was expected since a similar circumstance was experienced during ETC qualification testing for launch vibration. A leak existed in the seal of the spare magazine to the camera vacuum interface. For EREP passes 08 and 10, black-and-white film EK 3414 (roll no. 82) was installed in this spare magazine. Since there was an audible hiss, the vacuum hose was not connected to the camera. This caused the vacuum platen to be inoperable, resulting in some degradation in resolution for this roll of film. The vegetation of the South American jungle areas proved to be much darker than vegetation found in the United States, and was consequently about 1/2 stop underexposed in all cases.

Kenney, G. P.↗
NASA NTRS1984

An in-flight investigation of a twin fuselage configuration in approach and landing

An in-flight investigation of the flying qualities of a twin fuselage aircraft design in the approach and landing flight phase was carried out in the USAF/AFWAL Total In-Flight Simulator (TIFS). The objective was to determine the effects of actual motion and visual cues on the pilot when he was offset from the centerline of the aircraft. The experiment variables were lateral pilot offset position (0, 30 and 50 feet) and effective roll mode time constant (.6, 1.2, 2.4 seconds). The evaluation included the final approach, flare and touchdown. Lateral runway offsets and 15 knot crosswinds were used to increase the pilot's workload and force him to make large lateral corrections in the final portion of the approach. Results indicated that large normal accelerations rather than just vertical displacements in rolling maneuvers had the most significant degrading effect on pilot ratings. The normal accelerations are a result of large lateral offset and fast roll mode time constant and caused the pilot to make unnecessary pitch inputs and get into a coupled pitch/roll oscillation while he was making line up and crosswind corrections. A potential criteria for lateral pilot offset position effects is proposed. When the ratio of incremented normal aceleration at the pilot station to the steady state roll rate for a step input reaches .01 to .02 g/deg/sec a deterioration of pilot rating and flying qualities level can be expected.

Weingarten, N. C.↗
NASA NTRS1978

Considerations in the design of tip-coupled air-transport systems

It is shown that the lift-drag ratio of tip-coupled systems can be expressed as a simple multiple of the lift-drag ratio of the isolated units comprising the system. When operated for maximum lift-drag ratio, the extent of the coupled system is limited by maximum lift coefficient, high-altitude engine characteristics, and degraded performance of the isolated unit climbing to couple into the system. When operated at constant altitude, the gain from coupling is severely limited. If the cruise altitude is that for best performance of the isolated unit, the system lift-drag ratio can be no better than twice that of the isolated unit even when an infinite number of units are coupled. System performance may be further degraded since span-load distributions which yield good performance for the individual units reduce the efficiency of the coupled system. Coupling a pair of modern transport aircraft results in only about half the expected gain because of a poor span-distribution across the coupled pair. The control deflections required to maintain roll and pitch equilibrium further degrade the possible gain.

Heyson, H. H.↗
NASA NTRS1989

The application of electrochemical impedance spectroscopy for characterizing the degradation of Ni(OH)2/NiOOH electrodes

The use of wide-band electrochemical impedance spectroscopy is described for characterizing the degradation of porous Ni(OH)2/NiOOH electrodes in concentrated KOH electrolyte solutions. The impedance spectra are interpreted in terms of a finite electrical transmission line and the changes in the components of the electrical analog are followed as a function of cycle number. The degradation of the capacity of rolled and bonded Ni(OH)2/NiOOH electrodes is caused by rupture of ohmic contacts within the active mass and by restructuring which results in a decrease in the number of active pores.

Macdonald, Digby D.↗
NASA NTRS1987

Flight performance of the Pioneer Venus Orbiter solar array

The Pioneer Venus Orbiter (PVO) solar panel power output capability has degraded much more severely than has the power output capability of solar panels that have operated in earth-orbiting spacecraft for comparable periods of time. The incidence of solar proton events recorded by the spacecraft's scientific instruments accounts for this phenomenon only in part. It cannot explain two specific forms of anomalous behavior observed: 1) a variation of output per spin with roll angle, and 2) a gradual degradation of the maximum output. Analysis indicates that the most probable cause of the first anomaly is that the solar cells underneath the spacecraft's magnetometer boom have been damaged by a reverse biasing of the cells that occurs during pulsed shadowing of the cells by the boom as the spacecraft rotates. The second anomaly might be caused by the effects on the solar array of substances from the upper atmosphere of Venus.

Goldhammer, L. J.↗
NASA NTRS1975

Skylab program payload integration. Skylab film environmental effects

The effects of the Skylab environments on the 22 types of film used for data recording on Skylab were evaluated. Environmental histories and sensitometric curves for 114 rolls of film used for this evaluation are presented. Photographic parameters evaluated in detail were film fogging of black and white films, changes in maximum density of color film, latent image fading, and changes in film sensitivity. Other photographic and film physical anomalies such as electrostatic exposure, emulsion cracking, and reciprocity failure were also documented. Results based upon comparison of film sensitometric data for flight film with ground control film and ground test film are presented independently for each film type. The study showed that photographic film fulfilled the requirements of the Skylab applications in which it was used. Environmental film degradation, although present on almost every roll, did not preclude recording sufficient data to meet experiment requirements for all film, except film type SC-5. Specific conclusions are provided in the areas of further analyses, tests, and developments.

Source record↗
NASA NTRS1974

Reaction control system plume flow field interaction effects on the Space Shuttle orbiter

This paper presents an analysis of data obtained from wind tunnel tests of the aerodynamic interference induced by the reaction control system jets on Space Shuttle orbiter configurations. The test data was obtained using cold gas simulation techniques with nozzles scaled to match jet exit momentum ratio as the primary parameter at Mach numbers from 2.5 to 10. Significant induced effects have been found that degrade the performance of the pitch and roll reaction controls and that induce cross-coupling effects for yaw reaction control. Analysis of the induced data shows good correlation with jet exit momentum ratio.

Rausch, J. R.↗
NASA NTRS2008

Autonomous Formation Flight: Project Overview

Objectives: a) Map the vortex effects; b) Formation Auto-Pilot Requirements. Two NASA F/A-18 aircraft in formation: a) NASA 845 Systems Research Aircraft; b) NASA 847 Support Aircraft. Flight Conditions: M = 0.56, 25000 feet (Subsonic condition); b) M = 0.86, 36000 feet (Transonic condition). Nose-To-Tail (N2T) Distances: 20, 55, 110 and 190 feet. Lessons learned: a) Controllable flight in vortex is possible with pilot feedback (displays); b) Position hold at best C(sub D), is attainable; c) Best drag location is close to max rolling moment; e) Drag reductions demonstrated up to 22% (WFE up to 20%); f) Induced drag results compare favorably with simple prediction model; g) "Sweet Spot" (lateral & vertical area > 25%) is larger than predicted; h) Larger wing overlaps result in sign reversals in roll, yaw; i) As predicted, favorable effects degrade gradually with increased nose-to-tail distances after peaking at 3 span lengths aft; and j) Demonstrated - over 100 N mi (>15%) range improvement and 650 lbs (14%) fuel savings on actual simulated F/A-18 cruise mission.

Cole, Jennifer↗
NASA NTRS2007

Spiral Orbit Tribometer

The spiral orbit tribometer (SOT) bridges the gap between full-scale life testing and typically unrealistic accelerated life testing of ball-bearing lubricants in conjunction with bearing ball and race materials. The SOT operates under realistic conditions and quickly produces results, thereby providing information that can guide the selection of lubricant, ball, and race materials early in a design process. The SOT is based upon a simplified, retainerless thrust bearing comprising one ball between flat races (see figure). The SOT measures lubricant consumption and degradation rates and friction coefficients in boundary lubricated rolling and pivoting contacts. The ball is pressed between the lower and upper races with a controlled force and the lower plate is rotated. The combination of load and rotation causes the ball to move in a nearly circular orbit that is, more precisely, an opening spiral. The spiral s pitch is directly related to the friction coefficient. At the end of the orbit, the ball contacts the guide plate, restoring the orbit to its original radius. The orbit is repeatable throughout the entire test. A force transducer, mounted in-line with the guide plate, measures the force between the ball and the guide plate, which directly relates to the friction coefficient. The SOT, shown in the figure, can operate in under ultra-high vacuum (10(exp -9) Torr) or in a variety of gases at atmospheric pressure. The load force can be adjusted between 45 and 450 N. By varying the load force and ball diameter, mean Hertzian stresses between 0.5 and 5.0 GPa can be obtained. The ball s orbital speed range is between 1 and 100 rpm.

Pepper, Stephen V.↗