Search NASA⌕ Search

SEARCH · Search NASA

Results for “rotating ring disk electrode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Editors’ Choice—Rapid Deactivation Convolutes Electrochemical CO 2 Reduction Selectivity Measurements on Gold Rotating Ring Disk Electrodes

Voltammetric measurements of electrochemical CO 2 reduction reaction (CO 2 RR) selectivity on rotating ring disk electrodes (RRDE) are a rapid and sensitive method for quantifying an electrocatalyst’s selectivity, i.e. faradaic efficiency (FE). This method has been applied to polycrystalline Au electrocatalysts where a Au disk electrode catalyzes both the CO 2 RR and hydrogen evolution reaction while the concentric Au ring electrode selectively senses CO by oxidizing CO back to CO 2 . Such measurements enabled fundamental mechanistic studies but suffer from poor inter-laboratory reproducibility. This work identifies causes of variability in RRDE selectivity measurements by comparing protocols with different electrochemical methods, reagent purities, and glassware cleaning procedures. We observed FE CO decrease by 56% during 5 min chronoamperometry measurements, a phenomenon that is not readily apparent in voltammetric scans due to their dynamic nature. Electroplating of electrolyte impurities onto the disk and ring surfaces were identified as a major contributor to Au deactivation. Additionally, the oxygen reduction reaction may lead to higher disk currents in inadequately purged electrolytes, causing an apparent underestimation of FE CO at low overpotentials. Lastly, we propose operational bounds for CO 2 RR selectivity measurements on Au using the RRDE method and provide suggestions on steps for improving the accuracy of this technique.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Anodic Hydrogen Generation from Benzaldehyde on Au, Ag, and Cu: Rotating Ring-Disk Electrode Studies

Aldehydes are selectively oxidized to carboxylates on group 11 metals at low potentials (<0.4 V vs. RHE) in alkaline media. This process can occur by a pathway that generates H 2 gas from the aldehyde, known as electro-oxidative dehydrogenation (EOD) or anodic hydrogen production. The EOD process occurs with transfer of only one electron per aldehyde, whereas typical oxidation with discharge of hydrogen to form water is a two-electron process. Here, we study the catalytic activity and selectivity toward H 2 of Au, Ag, and Cu electrodes using benzaldehyde with rotating disk and ring-disk electrode (RDE/RRDE) techniques. The average number of electrons per benzaldehyde molecule obtained via H 2 detection by RRDE agrees with that obtained via Koutecký-Levich analysis conducted at various rotation rates. We find that Au and Ag have much higher H 2 and benzoate formation rates than Cu, but that Cu can perform the reaction at about 0.2 V lower overpotentials. On all three materials, benzaldehyde oxidation has high selectivity to anodic H 2 (one-electron pathway) below ∼0.5 V vs. RHE, but, with increasing potential, the selectivity shifts to H-oxidation forming water (two-electron pathway).

Ramos, Nathanael C. (ORCID:0000000247210350)↗
DOE OSTI2025

Insights into the mechanism of electrochemical chloride oxidation in ethanol from X-ray photoelectron spectroscopy, quiescent solution voltammetry, and rotating ring-disk electrodes

The wide availability of bio-derived alcohols provides the impetus to develop processes that convert them to valuable chemicals. The chloride ion is a redox mediator for electrocatalytic ethanol oxidation to 1,1-diethoxyethane (1,1-DEE) through an ethyl hypochlorite (EtOCl) intermediate, and this paper describes the chloride oxidation reaction (COR) to EtOCl on a glassy carbon (GC) electrode. Voltammetry measurements on a GC electrode in inert acetonitrile solvent combined with ex situ X-ray photoelectron spectroscopy (XPS) establish a Volmer step, where chloride ion from solution chemisorbs and is oxidized. In reactive ethanol solvent, ethanol adsorbs, and analyzing the current response in an LSV experiment supports a two-electron-transfer to form EtOCl, with chemisorption of the regenerated chloride. Koutecký–Levich (K–L) analysis on a rotating ring disk electrode (RRDE) shows that the kinetic rate constant of the COR in ethanol is on the order of 10 −8 cm s −1 , which is five orders of magnitude faster than the direct alcohol oxidation reaction in a kinetically limited regime. This hydrodynamic approach in understanding the electrochemistry of this non-aqueous system extends the possibilities for mediated electrocatalysis in neat alcohol solvents.

Van Daele, Ryan D. [University of Michigan, Ann Ar↗
DOE OSTI2025

Uniform secondary current distribution at disk electrodes under Tafel kinetics enabled by concentric current-shielding rings

Non-uniform secondary current distribution at rotating disk electrodes (RDE) is a common problem when using resistive electrolyte media or large applied currents. In a recent publication, we have shown that auxiliary electrodes such as the ring of a rotating ring disk electrode (RRDE) can help suppress current non-uniformities at the disk enabling reliable electroanalytical measurements. However, this previous work considered linear kinetics where current distribution non-uniformities were moderate. In the present contribution, we consider current distribution non-uniformities encountered under Tafel kinetics. We show, for the case of 2,5-dihydroxy-1,4-benzoquinone (DHBQ) reduction, that optimally chosen ring conditions serve to provide effective shielding at the disk edge rendering the overall disk current distribution to be uniform. Numerical modeling and scaling analysis (using the Wagner number) are presented to aid a user in determining the optimal ring current density for achieving uniform disk current distribution under Tafel kinetics. This approach is especially useful when studying soluble-soluble redox transitions for which, unlike deposit distribution in electrodeposition, the current distribution non-uniformity is not visually apparent.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Electrolyzers in focus: advances in CO 2 electrolyzer designs

Electrochemical CO 2 reduction (ECR) remains a viable method to reintegrate anthropogenic CO 2 into current energy infrastructures through its conversion into commodity chemicals. To facilitate the integration of ECR, electrochemical devices called electrolyzers must be implemented to overcome the inherent limitations that exist in current ECR experiments, namely kinetics and mass transport. In this review, we outline the current and advancing designs in ECR electrolyzers, with a focus on the following five electrochemical devices: membrane electrode assemblies (MEA), flow cell (FC), rotating disk electrode (RDE), rotating ring-disk electrode (RRDE), and rotating cylinder electrode (RCE). We highlight the tunable components of each electrolyzer with a forward outlook on the optimization and relevance of electrolyzer designs in upcoming ECR applications.

CO2 reduction↗
DOE OSTI2025

Kinetics Measurements in Resistive Electrolytes Using Ring-Disk Electrode: Ring as Current “Shield” Enables Uniform Disk Current Distribution

Rotating disk electrodes are commonly used for electrochemical kinetics measurements. A major disadvantage of these types of electrodes is their nonuniform secondary current distribution, especially when performing electroanalytical measurements in resistive electrolytes. Such nonuniform current distribution can render the values of kinetics constants extracted from the disk electrode to be highly inaccurate. Furthermore, one emerging class of electrolytes that suffer from low ionic conductivities is deep eutectic solvents (DES). DES are a promising class of electrolytes for various emerging applications; however, due to their resistive nature, the secondary current distribution when using them is typically highly nonuniform. For example, the Wagner number when measuring Cu²⁺/Cu⁺ kinetics in choline chloride–ethylene glycol DES (1:4 molar ratio of ChCl:EG) is very low (<0.1), indicating highly nonuniform current distribution over the disk electrode. We show here that the Cu²⁺/Cu⁺ exchange current density measured using disk electrodes is very inaccurate due to the aforementioned nonuniform current distribution. To obtain uniform disk current distribution, we employ here a coplanar concentric rotating ring-disk electrode (RRDE), where the ring serves the function of a current “shield.” Specifically, we show using modeling that the ring minimizes the current distribution nonuniformity at the disk by effectively shielding the disk against current spikes near the disk edge. This enables improved precision in electrode kinetics measurements for the Cu²⁺/Cu⁺ couple in resistive DES. To enable broad applicability of this technique, an analytical expression based on the Wagner number is integrated into an iterative algorithm to help users identify ring conditions to achieve uniform current distribution and thus improved electroanalytics at the disk.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1983

Electrochemical Studies of Redox Systems for Energy Storage

Particular attention was paid to the Cr(II)/Cr(III) redox couple in aqueous solutions in the presence of Cl(-) ions. The aim of this research has been to unravel the electrode kinetics of this redox couple and the effect of Cl(1) and electrode substrate. Gold and silver were studied as electrodes and the results show distinctive differences; this is probably due to the role Cl(-) ion may play as a mediator in the reaction and the difference in state of electrical charge on these two metals (difference in the potential of zero charge, pzc). The competition of hydrogen evolution with CrCl3 reduction on these surfaces was studied by means of the rotating ring disk electrode (RRDE). The ring downstream measures the flux of chromous ions from the disk and therefore separation of both Cr(III) and H2 generation can be achieved by analyzing ring and disk currents. The conditions for the quantitative detection of Cr(2+) at the ring electrode were established. Underpotential deposition of Pb on Ag and its effect on the electrokinetics of Cr(II)/Cr(III) reaction was studied.

Wu, C. D.↗
DOE OSTI2025

Nanoporous Fe 2 O 3 and Soluble Fe(II) Intermediates Accelerate the Electrodeposition of Fe in NaOH(aq)

Electrochemical conversion of iron oxide to iron metal can enable low-cost batteries for long duration energy storage and zero-emissions ironmaking for steel. Iron oxides, such as hematite, can be electrochemically reduced to metallic iron in concentrated alkaline electrolytes at modest temperatures, but the relative influences of solid-state and dissolved intermediates at practical reaction rates remains unclear. Here, in this study, we prepare a homologous set of well-defined hematite particles to measure how the nanoscale morphology of oxides controls both their reactivity and apparent reduction mechanism in concentrated hydroxide. Correlated electron microscopy and rotating-ring-disk-electrode measurements revealed that nanoporous hematite and solid intermediates formed iron via a dissolution-redeposition pathway. In contrast, dense hematite particles directly formed iron metal via reactive fracture. While previous studies on iron electrowinning have primarily emphasized the role of particle diameter at the micron scale, these results demonstrate the importance of the dissolution-redeposition pathway to support rapid reaction rates and suggest that nanoscale porosity controls iron oxide reactivity at temperatures <100 °C. Therefore, iron-oxide-to-metal electrolyzers and fast-charging iron-air batteries supported by curtailed electricity can increase the rate of metal formation by accelerating fracture and dissolution in reactant oxides.

TEM↗
DOE OSTI2026

Activating magnetite ores for aqueous ironmaking at high current densities

Low-temperature electrochemical cells reducing iron oxides to metal in alkaline electrolytes can support fully electrified steelmaking processes. Previous studies on these cells have primarily focused on high-surface-area hematite, Fe 2 O 3 , reactants whereas attempts to reduce suspensions of magnetite, Fe 3 O 4 —one of the two feedstocks for existing ironmaking reactors—have generally been limited to low rates of reaction (<30 mA cm −2 ). Here, in this study, we control the crystalline domain size of Fe 2 O 3 and Fe 3 O 4 particles in 10 M NaOH electrolytes to study how the nanoscale morphology of oxides controls the rate of electrochemical ironmaking. Rotating-ring disk electrode measurements of Fe 2+ , in situ Raman spectroscopy of the electrode surface, and ex situ electron microscopy were consistent with a hypothesized passivation process at Fe 3 O 4 surfaces that may prevent the continuous formation of soluble intermediates. Sufficiently small (<100 nm diameter) oxide particles yielded Fe partial current densities >160 mA cm −2 , a fivefold increase relative to previously reported rates for Fe 3 O 4 suspensions and comparable to active Fe 2 O 3 . Electron microscopy revealed that electrodeposited films were composed of micron-scale crystalline Fe domains with a porous film of Fe 3 O 4 nanoparticles and supports a model where Fe is grown primarily from soluble Fe 2+ intermediates. Based on these insights, inactive blast-furnace-grade iron-oxides were transformed into high surface area nanoparticles (1.6 to 229.2 m 2 g −1 ) via reprecipitation, leading to a ninefold enhancement in faradaic efficiency and an Fe partial current density of 120 mA cm −2 . When integrated with chlor-iron cells producing reagents for reprecipitation, this approach could lead to a cost-competitive process for electrochemical ironmaking from industrially relevant feedstocks.

TEM↗
NASA NTRS1984

Electrocatalysis of fuel cell reactions: Investigation of alternate electrolytes

Oxygen reduction and transport properties of the electrolyte in the phosphoric acid fuel cell are studied. The areas covered were: (1) development of a theoretical expression for the rotating ring disk electrode technique; (2) determination of the intermediate reaction rate constants for oxygen reduction on platinum in phosphoric acid electrolyte; (3) determination of oxygen reduction mechanism in trifluoreomethanesulfonic acid (TFMSA) which was considered as an alternate electrolyte for the acid fuel cells; and (4) the measurement of transport properties of the phosphoric acid electrolyte at high concentrations and temperatures.

Chin, D. T.↗
DOE OSTI2025

Hydrodynamic characterization of the redox chemistry of crown-encapsulated uranyl complexes

The redox properties of actinide-containing species strongly influence their reactivity, speciation, and interfacial behavior, but the experimental quantification of the electrochemical characteristics of molecular actinide complexes in nonaqueous media has not received the attention it deserves. Here, results from hydrodynamic methods and electrochemical simulations of U(VI)/U(V) redox are reported, including quantification of heterogeneous electron-transfer kinetics and estimation of chemical reversibility of U(VI)/U(V) interconversion at electrodes in acetonitrile-based electrolyte. The complexes investigated are recently reported U(VI) and U(V) complexes in which the uranyl ion (UO 2 n+ ) is encapsulated in a macrocyclic 18-crown-6-like moiety templated by a Pt(II) center. These complexes feature the most positive value U VI /U V reduction potential yet reported and are thus particularly relevant to study of facile U(V) generation from U(VI) precursors as well as uranium electroanalysis. Rotating disk electrode (RDE) studies have been used to quantify the diffusion coefficients of the U(VI) and U(V) complexes, and standard heterogeneous electron transfer rate constants ( k 0 ) for the redox have been determined using a conventional Koutecký-Levich analysis. Rotating ring-disk electrode (RRDE) studies have been used to directly interrogate the chemical reversibility of U(VI)-U(V) interconversion, confirming that reduction of the U(VI) complex at an Au disk is associated with formation of the U(V) analogue that can be readily re-oxidized at a Pt ring under hydrodynamic (rotating) conditions. Because measurements of the type reported here are generally associated with current flows that are larger than those found in corresponding quiescent (unstirred) conditions, our findings suggest that hydrodynamic methods could be advantageous for design of electroanalytical approaches to detection of actinide species and study of their redox properties.

actinides↗
NASA NTRS1989

Electrocatalysis for oxygen electrodes in fuel cells and water electrolyzers for space applications

In most instances separate electrocatalysts are needed to promote the reduction of O2 in the fuel cell mode and to generate O2 in the energy storage-water electrolysis mode in aqueous electrochemical systems operating at low and moderate temperatures (T greater than or equal to 200 C). Interesting exceptions are the lead and bismuth ruthenate pyrochlores in alkaline electrolytes. These catalysts on high area carbon supports have high catalytic activity for both O2 reduction and generation. Rotating ring-disk electrode measurements provide evidence that the O2 reduction proceeds by a parallel four-electron pathway. The ruthenates can also be used as self-supported catalysts to avoid the problems associated with carbon oxidation, but the electrode performance so far achieved in the research at Case Western Reserve University (CWRU) is considerably less. At the potentials involved in the anodic mode the ruthenate pyrochlores have substantial equilibrium solubility in concentrated alkaline electrolyte. This results in the loss of catalyst into the bulk solution and a decline in catalytic activity. Furthermore, the hydrogen generation counter electrode may become contaminated with reduction products from the pyrochlores (lead, ruthenium).

Prakash, Jai↗
NASA NTRS1989

Electrocatalysts for oxygen electrodes in fuel cells and water electrolyzers for space applications

In most instances separate electrocatalysts are needed to promote the reduction of O2 in the fuel cell mode and to generate O2 in the energy storage-water electrolysis mode in aqueous electrochemical systems operating at low and moderate temperatures (T greater than or equal to 200 C). Interesting exceptions are the lead and bismuth ruthenate pyrochlores in alkaline electrolytes. These catalysts on high area carbon supports have high catalytic activity for both O2 reduction and generation (1,2). Rotating ring-disk electrode measurements provide evidence that the O2 reduction proceeds by a parallel four-electron pathway. The ruthenates can also be used as self-supported catalysts to avoid the problems associated with carbon oxidation, but the electrode performance so far achieved in the research at Case Western Reserve University (CWRU) is considerably less. At the potentials involved in the anodic mode the ruthenate pyrochlores have substantial equilibrium solubility in concentrated alkaline electrolyte. This results in the loss of catalyst into the bulk solution and a decline in catalytic activity. Furthermore, the hydrogen generation counter electrode may become contaminated with reduction products from the pyrochlores (lead, ruthenium). A possible approach to this problem is to immobilize the pyrochlore catalyst within an ionic-conducting solid polymer, which would replace the fluid electrolyte within the porous gas diffusion O2 electrode. For bulk alkaline electrolyte, an anion-exchange polymer is needed with a transference number close to unity for the Oh(-) ion. Preliminary short-term measurements with lead ruthenates using a commercially available partially-fluorinated anion-exchange membrane as an overlayer on the porous gas-fed electrode indicate lower anodic polarization and virtually unchanged cathodic polarization.

Prakash, Jai↗
DOE OSTI2025

Quantification of Reactive Oxygen Species Produced from Electrocatalytic Materials

Oxygen electrochemistry goes beyond O 2 , as the formation of reactive oxygen species (ROS) such as H 2 O 2 and O 3 during water oxidation is key in the destruction of persistent pollutants in water remediation technologies as well as in the degradation of fuel cell and electrolyzer components. In this study, we developed an in situ method utilizing the rotating ring-disk electrode technique to quantify the formation of O 2 , O 3 , and H 2 O 2 species across a broad pH range (1–8.3). Oxygen selectivity trends over Pt, IrO 2 , and PbO 2 surfaces reveal that even O 2 evolution catalysts may produce small yet measurable amounts of ROS, further modulated by pH and electrode potential. In conclusion, these findings emphasize the need to probe the selectivity of oxygen electrochemistry for a more complete picture of advanced materials for electrochemical technologies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Electrochemical Corrosion and Catalysis Dynamics of Tin Oxide during Water Oxidation

Metal oxide corrosion severely limits anodic electrocatalysis, particularly at high potentials in acidic environments, where degradation pathways remain poorly defined. This study establishes explicit connections between corrosion and electrocatalysis on tin oxide during water oxidation by examining the roles of lattice defects, reactive oxygen species, interfacial pH variations, and speciation of corroded tin in acid. We first demonstrate the presence of structural defects such as oxygen vacancies and substoichiometric Sn(II) species by integrating electron paramagnetic resonance spectroscopy, ultraviolet photoelectron spectroscopy, and Mott–Schottky analysis. Kohn–Sham density functional theory calculations reveal that explicit water structures thermodynamically stabilize reaction intermediates and lower reaction overpotentials. Moreover, we propose that water dissociation leads to hydrogen-bonding networks formed by H* and OH* intermediates, which may span the entire catalyst surface and decrease the interfacial pH to drive corrosion. In contrast, the electrochemical generation of reactive oxygen species is shown to play a minor role in catalyst corrosion during water oxidation using inductively coupled plasma mass spectrometry coupled with selective chemical scavengers. Square-wave voltammetry combined with rotating ring-disk electrodes is used to reveal that under open-circuit conditions, only Sn(IV) cations chemically dissolve from tin oxide, while both Sn(IV) and Sn(II) species electrochemically corrode during water oxidation. Our results unveil a dynamic and complicated interplay between corrosive and catalytic pathways on metal oxide electrocatalysts: a decrease in interfacial pH due to water oxidation exacerbates Sn(II)/Sn(IV) corrosion. Subsequently, the electrochemical corrosion of Sn(II)/Sn(IV) facilitates product formation from lattice oxygen, while the redeposition of corroded Sn(II) as Sn(IV) can enable oxygen exchange with water. By elucidating the roles of defects and interfacial chemistry, this work provides a roadmap for engineering improved electrocatalysts that balance activity and stability, a critical step toward scalable and durable energy technologies.

36 MATERIALS SCIENCE↗
NASA NTRS1983

Electrocatalysis of fuel cell reactions: Investigation of alternate electrolytes

Oxygen reduction and transport properties of the electrolyte in the phosphoric acid fuel cell are studied. A theoretical expression for the rotating ring-disk electrode technique; the intermediate reaction rate constants for oxygen reduction on platinum in phosphoric acid electrolyte; oxygen reduction mechanism in trifluoromethanesulfonic acid (TFMSA), considered as an alternate electrolyte for the acid fuel cells; and transport properties of the phosphoric acid electrolyte at high concentrations and temperatures are covered.

Chin, D. T.↗
NASA NTRS1987

Organometallic catalysts for primary phosphoric acid fuel cells

A continuing effort by the U.S. Department of Energy to improve the competitiveness of the phosphoric acid fuel cell by improving cell performance and/or reducing cell cost is discussed. Cathode improvement, both in performance and cost, available through the use of a class of organometallic cathode catalysts, the tetraazaannulenes (TAAs), was investigated. A new mixed catalyst was identified which provides improved cathode performance without the need for the use of a noble metal. This mixed catalyst was tested under load for 1000 hr. in full cell at 160 to 200 C in phosphoric acid H3PO4, and was shown to provide stable performance. The mixed catalyst contains an organometallic to catalyze electroreduction of oxygen to hydrogen peroxide and a metal to catalyze further electroreduction of the hydrogen peroxide to water. Cathodes containing an exemplar mixed catalyst (e.g., Co bisphenyl TAA/Mn) operate at approximately 650 mV vs DHE in 160 C, 85% H3PO4 with oxygen as reactant. In developing this mixed catalyst, a broad spectrum of TAAs were prepared, tested in half-cell and in a rotating ring-disk electrode system. TAAs found to facilitate the production of hydrogen peroxide in electroreduction were shown to be preferred TAAs for use in the mixed catalyst. Manganese (Mn) was identified as a preferred metal because it is capable of catalyzing hydrogen peroxide electroreduction, is lower in cost and is of less strategic importance than platinum, the cathode catalyst normally used in the fuel cell.

Walsh, Fraser↗