Search NASA⌕ Search

SEARCH · Search NASA

Results for “roughness”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2017

The influence of interfacial slip on two-phase flow in rough pores

The migration and trapping of supercritical CO 2 (scCO 2 ) in geologic carbon storage is strongly dependent on the geometry and wettability of the pore network in the reservoir rock. During displacement, resident fluids may become trapped in the pits of a rough pore surface forming an immiscible two-phase fluid interface with the invading fluid, allowing apparent slip flow at this interface. We present a two-phase fluid dynamics model, including interfacial tension, to characterize the impact of mineral surface roughness on this slip flow. We show that the slip flow can be cast in more familiar terms as a contact-angle (wettability)-dependent effective permeability to the invading fluid, a nondimensional measurement which relates the interfacial slip to the pore geometry. The analysis shows the surface roughness-induced slip flow can effectively increase or decrease this effective permeability, depending on the wettability and roughness of the mineral surfaces. Configurations of the pore geometry where interfacial slip has a tangible influence on permeability have been identified. The results suggest that for large roughness features, permeability to CO 2 may be enhanced by approximately 30% during drainage, while the permeability to brine during reimbibition may be enhanced or diminished by 60%, depending on the contact angle with the mineral surfaces and degrees of roughness. For smaller roughness features, the changes in permeability through interfacial slip are small. As a result, a much larger range of effective permeabilities are suggested for general fluid pairs and contact angles, including occlusion of the pore by the trapped phase.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Direct Numerical Simulation of Transitional and Turbulent Flows Over Multi-Scale Surface Roughness—Part II: The Effect of Roughness on the Performance of a High-Pressure Turbine Blade

Abstract Turbine blades generally present surface roughness introduced in the manufacturing process or caused by in-service degradation, which can have a significant impact on aero-thermal performance. A better understanding of the fundamental physical mechanisms arising from the interaction between the roughness and the turbine flow at engine-relevant conditions can provide insights for the design of blades with improved efficiency and longer operational life. To this end, a high-fidelity numerical framework combining a well-validated solver for direct numerical simulation and a second-order accurate immersed boundary method is employed to predict roughness-induced aero-thermal effects on an LS89 high-pressure turbine (HPT) blade at engine-relevant conditions. Different amplitudes and distributions of surface roughness are investigated and a reference smooth-blade simulation under the same flow conditions is conducted for comparison. Roughness of increasing amplitude progressively shifts the blade suction side boundary layer transition upstream, producing larger values of the turbulent kinetic energy and higher total wake losses. The on-surface data-capturing capabilities of the numerical framework provide direct measurements of the heat flux and the skin friction coefficient, hence offering quantitative information between the surface topology and engineering-relevant performance parameters. This work may provide a benchmark for future numerical studies of turbomachinery flows with roughness.

Engineering↗
DOE OSTI2022

Investigation of Gas Turbine Internal Cooling Using Supercritical CO 2 —Effect of Surface Roughness and Channel Aspect Ratio

In this paper, an experimental and numerical investigation of internal cooling channels with rib turbulators is presented with sCO 2 as the working fluid at process conditions (pressure-20.7 MPa and temperature up to 150 °C). The effect of channel aspect ratio up to 2:1 on thermal-hydraulic performance is explored in additively manufactured rectangular channels and square channels, both with and without 60 deg ribs on the top and bottom sides. The Wilson-plot method is employed to experimentally measure channel-averaged Nusselt number over a Reynolds number range up to 370,000. The friction factor is calculated from pressure drop and mass flow rate and additionally, the overall thermal performance factor (TPF) is reported. A companion computational fluid dynamics (CFD) simulation is performed for the rib turbulated cooling configurations reported in the experiments using the Reynolds average Navier–Stokes-based turbulence model. The objective of the numerical study is to gain insight into the local heat transfer augmentation in the ribbed channels as a result of varying the aspect ratio, channel configuration (square versus rectangular), operating conditions (Reynolds number) and the surface roughness, an inherent outcome of the additive manufacturing process. Surface roughness is simulated using sand grain roughness height (K S ) calculated from the experimental data, and a comparison is presented with the corresponding channel configuration with varying surface roughness heights starting from smooth surfaces (K S = 0). Experimental results indicate that the heat transfer augmentation is negligible in the rectangular channels with ribs on the long side compared to the square channel. However, it is enhanced by 60% in comparison to placing ribs on the shorter side. The TPF remains constant at around 1 for the entire range of Reynolds numbers consistent with prior work at the National Energy Technology Laboratory (NETL). Here, the simulation results highlight that increased surface roughness can have a favorable considerable influence on Nusselt number and overall thermal performance enhancement.

42 ENGINEERING↗
DOE OSTI2020

A constitutive model for sheared dense suspensions of rough particles

In a concentrated suspension, particles come into contact due to the presence of asperities on their surfaces. As a result, the contact forces and interparticle friction become one of the important factors governing the rheology of rigid particle suspensions at high concentrations. We show that a load-dependent friction model can be used to reproduce the experimentally observed shear thickening [ST—continuous and discontinuous (DST)] behavior with an increase in the asperity size. Increasing the particle surface roughness size leads to a decrease in the critical shear rate above which shear-thickening takes place, a reduction in the critical volume fraction for DST and an increase in the viscosity jump across non-shear-thickened to shear-thickened regime. In this paper, we propose a constitutive model to quantify the effect of increasing the roughness size on the rheology of dense ST suspensions as well as on the critical shear rate for ST and the critical volume fraction for DST. We fit this model to our simulation data for stress controlled shear flow of dense rough particle suspensions. Once the fitting is complete, these equations are used to predict exact volume fractions and shear stress values for transitions between three regimes on the shear stress-shear rate flow state diagram for different roughness values. Furthermore, the results of this study can be used to tune the particle surface roughness for manipulating the dense suspension rheology according to different applications.

42 ENGINEERING↗
DOE OSTI2020

Fractal Model for Drag Reduction on Multiscale Nonwetting Rough Surfaces

Rough surfaces in contact with a flow of fluid exhibit alternating no-slip and free shear boundary conditions at the solid–liquid and air–liquid interfaces, respectively, thereby potentially offering drag reduction benefits. The balance between the dynamic pressure in the flow and the restoring capillary pressure in the interasperity spaces determines the stability of the Cassie state of wettability and is a function of the relative extent of no-slip and free shear regions per unit surface area. In the present study, using a fractal representation of rough surface topography, an analytical model is developed to quantify the stability of the Cassie state of wettability as well as drag reduction and the friction factor for laminar flow in a rectangular channel between nonwetting multiscale rough surfaces. A systematic study is conducted to quantify the effects of fractal parameters of the surfaces and the flow Reynolds number on drag reduction and the friction factor. The studies are used to develop friction factor curves extending the classical Moody diagram to hydrophobic and superhydrophobic surfaces. On the basis of the studies, regime maps are derived for estimating the extent of drag reduction offered by hydrophobic and superhydrophobic surfaces, revealing that superhydrophobic surfaces do not always offer the best drag reduction performance. The application of the fractal model to practical topographies of nonwetting surfaces of copper, aluminum, and zinc oxide fabricated via electrodeposition and etching is also discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Coaxial Ceramic Direct Ink Writing on Heterogenous and Rough Surfaces: Investigation of Core–Shell Interactions

In this work, coaxial conductor–ceramic direct ink writing enables the printing of sensitive or encapsulated materials onto heterogeneous and rough substrates. While encasing the core fluid within a stiff ceramic shell, continuity may be maintained, even while printing onto conventionally challenging substrates. Here, we report the development of a coaxial ceramic direct ink writing suite and explore coflow interrelationships based on microfluidic principles. A coaxial nozzle is designed to facilitate the coextrusion of an alumina shell, whereas indium–tin-oxide inks constitute the core. In this manner, a core–shell ceramic element may be printed onto rough substrates for future high-temperature applications. Colloidal inks are engineered to provide the required rheological and sintering performance. Moreover, flow simulations in conjunction with microfluidic coflow principles are used to explore the coaxial printing processing space, thus controlling the core–shell architectures. Physical modeling is further used to analyze core deformations and eccentricity. As a result, simulations are validated experimentally, and the analyses are used to deposit coaxial ceramic features onto heterogeneous, high-temperature ceramic substrates.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2021

Preparation of Ultrathin Gold Films with Subatomic Surface Roughness

Nanoscale device fabrication requires control over film growth at the atomic scale. Growth conditions must be tuned in consideration of interface parameters like chemical bonding, surface free energy, and lattice matching. In metals, electronic properties may also be utilized for control of physical parameters. Quantum size effects can induce metals to spontaneously form specific shapes and sizes according to their electronic structure. Unfortunately, such electronic growth is generally known only for a few systems and is typically only stable under cryogenic conditions. In this work, we explore a recently discovered class of electronic growth systems in which metal films are grown upon the relatively inert surfaces of van der Waals crystals. In this class of materials, the electronic growth is highly stable at room temperature and actually requires higher temperature annealing to achieve proper equilibrium. We work with the Au/MoS 2 system, which shows excellent stability and can readily form discrete and atomically flat nanostructures. Here, we show how the electronic growth modes facilitate the formation of atomically flat films with nanometer scale thickness. Here, the surface roughness of these films was found to be less than a single atom over several square microns, creating nearly perfect surfaces for studies of self-assembled monolayers or other applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗