Search NASA⌕ Search

SEARCH · Search NASA

Results for “s_0.1 concentration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Photoinitiator Selection and Concentration in Photopolymer Formulations towards Large-Format Additive Manufacturing

Photopolymers are an attractive option for large-format additive manufacturing (LFAM), because they can be formulated from structural thermosets and cure rapidly in ambient conditions under low-energy ultraviolet light-emitting diode (UV LED) lamps. Photopolymer cure is strongly influenced by the depth penetration of UV light, which can be limited in the 2–4 mm layer thicknesses typical of LFAM. Photoinitiator (PI) systems that exhibit photobleaching have proven useful in thick-section cure applications, because they generate a photoinitiation wavefront, but this effect is time-dependent. This study investigates the light transmission and through-thickness cure behavior in (meth)acrylate photopolymer formulations with the photobleaching initiator bis(2,4,6-trimethylbenzoyl)-phenylphosphine oxide (BAPO). Utilizing an optical model developed by Kenning et al., lower concentrations (0.1 wt% to 0.5 wt%) of BAPO were predicted to yield rapid onset of photoinitiation. In situ cure measurements under continuous UV LED irradiation of 380 mW/cm2 showed that a 0.1 wt% concentration of BAPO achieved peak polymerization rate within 2.5 s at a 3-mm depth. With only 1 s of irradiation at 1.7 W/cm2 intensity, the 0.1 wt% BAPO formulation also achieved the highest level of cure of the formulas tested. For an irradiation dose of 5.5 J/cm2 at a duration of 3.7 s, cured polymer specimens achieved a flexural strength of 108 MPa and a flexural modulus of 3.1 GPa. This study demonstrates the utility of optical modeling as a potential screening tool for new photopolymer formulations, primarily in identifying an upper limit to PI concentration for the desired cure depth. The results also show that photobleaching provides only a limited benefit for LFAM applications with short (1.0 s to 3.7 s) UV irradiation times and indicate that excess PI concentration can inhibit light transmission even under extended irradiation times up to 60 s.

36 MATERIALS SCIENCE↗

Preferential flow systems amended with biogeochemical components: imaging of a two-dimensional study

The vadose zone is a highly interactive heterogeneous system through which water enters the subsurface system by infiltration. This paper details the effects of simulated plant exudate and soil component solutions upon unstable flow patterns in a porous medium (ASTM silica sand; US Silica, Ottawa, IL, USA) through the use of two-dimensional tank light transmission method (LTM). The contact angle (θ) and surface tension (γ) of two simulated plant exudate solutions (i.e., oxalate and citrate) and two soil component solutions (i.e., tannic acid and Suwannee River natural organic matter, SRNOM) were analyzed to determine the liquid–gas and liquid–solid interface characteristics of each. To determine if the unstable flow formations were dependent on the type and concentration of the simulated plant exudates and soil components, the analysis of the effects of the simulated plant exudate and soil component solutions were compared to a control solution (Hoagland nutrient solution with 0.01 M NaCl). Fingering flow patterns, vertical and horizontal water saturation profiles, water saturation at the fingertips, finger dimensions and velocity, and number of fingers were obtained using the light transmission method. Significant differences in the interface properties indicated a decrease between the control and the plant exudate and soil component solutions tested; specifically, the control (θ = 64.5° and γ = 75.75mNm -1 ) samples exhibited a higher contact angle and surface tension than the low concentration of citrate (θ = 52.6° and γ = 70.8mNm -1 ). Wetting front instability and fingering flow phenomena were reported in all infiltration experiments. The results showed that the plant exudates and soil components influenced the soil infiltration as differences in finger geometries, velocities, and water saturation profiles were detected when compared to the control. Among the tested solutions and concentrations of soil components, the largest finger width (10.19cm) was generated by the lowest tannic acid solution concentration (0.1mgL -1 ), and the lowest finger width (6.00cm) was induced by the highest SRNOM concentration (10mgL -1 ). Similarly, for the plant exudate solutions, the largest finger width (8.36cm) was generated by the lowest oxalate solution concentration (0.1mgL -1 ), and the lowest finger width (6.63cm) was induced by the lowest citrate concentration (0.1mgL -1 ). The control solution produced fingers with average width of 8.30cm. Additionally, the wettability of the medium for the citrate, oxalate, and SRNOM solutions increased with an increase in concentration. Our research demonstrates that the plant exudates and soil components which are biochemical compounds produced and released in soil are capable of influencing the process of infiltration in soils. The results of this research also indicate that soil wettability, expressed as cosθ 1/2 , should be included in the scaling of the finger dimension, i.e., finger width, when using the Miller and Miller (1956) scaling theory for the scaling of flow in porous media.

58 GEOSCIENCES↗

Fractal dimension of cohesive sediment flocs at steady state under seven shear flow conditions

The morphological properties of kaolin flocs were investigated in a Couette-flow experiment at the steady state under seven shear flow conditions (shear rates of 5.36, 9.17, 14, 24, 31, 41 and 53 s -1 ). These properties include a one-dimensional (1-D) fractal dimension (D 1 ), a two-dimensional (2-D) fractal dimension (D 2 ), a perimeter-based fractal dimension (D pf ) and an aspect ratio (AR). They were calculated based on the projected area (A), equivalent size, perimeter (P) and length (L) of the major axis of the floc determined through sample observation and an image analysis system. The parameter D 2 , which characterizes the relationship between the projected area and the length of the major axis using a power function, A ∝ L D 2 , increased from 1.73 ± 0.03, 1.72 ± 0.03, and 1.75 ± 0.04 in the low shear rate group (G = 5.36, 9.17, and 14 s -1 ) to 1.92 ± 0.03, 1.82 ± 0.02, 1.85 ± 0.02, and 1.81 ± 0.02 in the high shear rate group (24, 31, 41 and 53 s -1 ), respectively. The parameter D 1 characterizes the relationship between the perimeter and length of the major axis by the function P ∝ L D 1 and decreased from 1.52 ± 0.02, 1.48 ± 0.02, 1.55 ± 0.02, and 1.63 ± 0.02 in the low shear group (5.36, 9.17, 14 and 24 s -1 ) to 1.45 ± 0.02, 1.39 ± 0.02, and 1.39 ± 0.02 in the high shear group (31, 41 and 53 s -1 ), respectively. The results indicate that with increasing shear rates, the flocs become less elongated and that their boundary lines become tighter and more regular, caused by more breakages and possible restructurings of the flocs. The parameter D pf , which is related to the perimeter and the projected area through the function , decreased as the shear rate increased almost linearly. The parameter AR, which is the ratio of the length of the major axis and equivalent diameter, decreased from 1.56, 1.59, 1.53 and 1.51 in the low shear rate group to 1.43, 1.47 and 1.48 in the high shear rate group. These changes in D pf and AR show that the flocs become less convoluted and more symmetrical and that their boundaries become smoother and more regular in the high shear rate group than in the low shear rate group due to breakage and possible restructuring processes. To assess the effects of electrolyte and sediment concentration, 0.1 mol/L calcium chloride (CaCl 2 ) and initial sediment concentration from 7.87 × 10 -5 to 1.57 × 10 -5 were used in this preliminary study. The addition of electrolyte and increasing sediment concentration could produce more symmetrical flocs with less convoluted and simpler boundaries. In addition, some new information on the temporal variation of the median size of the flocs during the flocculation process is presented.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Crystallization and Phase Transformations of Aluminum (Oxy)hydroxide Polymorphs in Caustic Aqueous Solution

Gibbsite, bayerite, and boehmite are important aluminum (oxy)hydroxide minerals in nature and have been widely deployed in various industrial applications. They are also major components in caustic nuclear wastes stored at various U.S. locations. Knowledge of their crystallization and phase transformation processes contributes to understanding their occurrence and could help optimize waste treatment processes. While it has been reported that partial conversion of bayerite and gibbsite to boehmite occurs in basic solutions at elevated temperatures, systematic studies of factors affecting the phase transformation as well as the underlying reaction mechanisms are non-existent, particularly in highly alkaline solutions. We explored the effects of sodium hydroxide concentrations (0.1~3 M), reaction temperature (60~100 ?) and aluminum concentrations (0.1~1 M) on the crystallization and transformation of these aluminum (oxy)hydroxides. Detailed structural and morphological characterization by X-ray diffraction (XRD), scanning electron microscopy (SEM), and nuclear magnetic resonance (NMR) spectrometry revealed that these processes depend largely on the reaction temperature and the Al/OH- ratio. When 1 = Al/OH- = 2.5, the reactions favor formation of high crystallinity precipitates, whereas at Al/OH- ratio ? 2.5 precipitation ceases unless the Al concentration is higher than 1 M. We identified pseudoboehmite, bayerite and gibbsite as intermediate phases to bayerite, gibbsite and boehmite, respectively, all of which transform via dissolution-reprecipitation. Gibbsite transforms to boehmite in both acidic and weak caustic environments at temperatures above 80 oC. However, a ‘bar-shaped’ gibbsite morphology dominates in highly caustic environments (3 M NaOH). The findings enable a robust basis for selection of various solid phases by tuning the reaction conditions.

aluminum (oxy)hydroxide polymorphs, crystallizatio↗

Characterization of organic aerosol across the global remote troposphere: a comparison of ATom measurements and global chemistry models

The spatial distribution and properties of submicron organic aerosol (OA) are among the key sources of uncertainty in our understanding of aerosol effects on climate. Uncertainties are particularly large over remote regions of the free troposphere and Southern Ocean, where very few data have been available and where OA predictions from AeroCom Phase II global models span 2 to 3 orders of magnitude, greatly exceeding the model spread over source regions. The (nearly) pole-to-pole vertical distribution of non-refractory aerosols was measured with an aerosol mass spectrometer onboard the NASA DC-8 aircraft as part of the Atmospheric Tomography (ATom) mission during the Northern Hemisphere summer (August 2016) and winter (February 2017). This study presents the first extensive characterization of OA mass concentrations and their level of oxidation in the remote atmosphere. OA and sulfate are the major contributors by mass to submicron aerosols in the remote troposphere, together with sea salt in the marine boundary layer. Sulfate was dominant in the lower stratosphere. OA concentrations have a strong seasonal and zonal variability, with the highest levels measured in the lower troposphere in the summer and over the regions influenced by biomass burning from Africa (up to 10 µg sm -3 ). Lower concentrations (~0.1–0.3 µg sm -3 ) are observed in the northern middle and high latitudes and very low concentrations (<0.1 µg sm -3 ) in the southern middle and high latitudes. The ATom dataset is used to evaluate predictions of eight current global chemistry models that implement a variety of commonly used representations of OA sources and chemistry, as well as of the AeroCom-II ensemble. The current model ensemble captures the average vertical and spatial distribution of measured OA concentrations, and the spread of the individual models remains within a factor of 5. These results are significantly improved over the AeroCom-II model ensemble, which shows large overestimations over these regions. However, some of the improved agreement with observations occurs for the wrong reasons, as models have the tendency to greatly overestimate the primary OA fraction and underestimate the secondary fraction. Measured OA in the remote free troposphere is highly oxygenated, with organic aerosol to organic carbon (OA/OC) ratios of ~2.2–2.8, and is 30 %–60 % more oxygenated than in current models, which can lead to significant errors in OA concentrations. The model–measurement comparisons presented here support the concept of a more dynamic OA system as proposed by Hodzic et al. (2016), with enhanced removal of primary OA and a stronger production of secondary OA in global models needed to provide better agreement with observations.

54 ENVIRONMENTAL SCIENCES↗

Shape-Selective Catalysts for Fischer-Tropsch Chemistry: January 1, 2001 - December 31, 2008 (Final Report)

Argonne National Laboratory carried out a research program to create, prepare, and evaluate catalysts to promote Fischer-Tropsch (FT) chemistry-specifically, the reaction of hydrogen with carbon monoxide to form long-chain hydrocarbons. In addition to needing high activity, it was desirable that the catalysts have high selectivity and stability with respect to both mechanical strength and aging properties. It was desired that selectivity be directed toward producing diesel fraction components and avoiding excess yields of both light hydrocarbons and heavy waxes. The original goal was to produce shape-selective catalysts that had the potential to limit the formation of long-chain products and yet retain the active metal sites in a protected 'cage.' This cage would also restrict their loss by attrition during use in slurry-bed reactors. The first stage of this program was to prepare and evaluate iron-containing particulate catalysts. Such catalysts were prepared with silica-containing fractal cages. The activity and strength was essentially the same as that of catalysts without the cages. Since there was no improvement, the program plan was modified as discussed below. A second experimental stage was undertaken to prepare and evaluate active FT catalysts formed by atomic-layer deposition [ALD] of active components on supported membranes and particulate supports. The concept was that of depositing active metals (i.e. ruthenium, iron or cobalt) upon membranes with well defined flow channels of small diameter and length such that the catalytic activity and product molecular weight distribution could be controlled. In order to rapidly evaluate the catalytic membranes, the ALD coating processes were performed in an 'exploratory mode' in which ALD procedures from the literature appropriate for coating flat surfaces were applied to the high surface area membranes. Consequently, the Fe and Ru loadings in the membranes were likely to be smaller than those expected for complete monolayer coverage. In addition, there was likely to be significant variation in the Fe and Ru loading among the membranes due to difficulties in nucleating these materials on the aluminum oxide surfaces. The first series of experiments using coated membranes demonstrated that the technology needed further improvement. Specifically, observed catalytic FT activity was low. This low activity appeared to be due to: (1) low available surface area, (2) atomic deposition techniques that needed improvements, and (3) insufficient preconditioning of the catalyst surface prior to FT testing. Therefore, experimentation was expanded to the use of particulate silica supports having defined channels and reasonably high surface area. An effective FT catalyst consisting of ALD-deposited Co and Pt on a silica support has been prepared and demonstrated. This catalyst was more effective than a similar catalyst deposited upon a support of ALD-deposited Al 2 O 3 on silica. This result implies that the deposition of Al 2 O 3 to form a support is not as effective as desired. The addition of Pt as a Co-containing catalyst promoter has been demonstrated; it appears to primarily affect the catalyst pre-conditioning step. Co on Al 2 O 3 catalyst prepared by the Center for Applied Energy Research (CAER) is more effective than Argonne-prepared ALD-deposited Co on ALD-deposited Al 2 O 3 catalyst. The FT activity of ALD-coated Co catalyst on Al 2 O 3 is about linear with Co level from about 9 to 25%. A cooperative research effort was undertaken to test the deposition of platinum on Co FT catalysts; this Pt influences the effectiveness of catalyst conditioning and its continuing activity. In summary, the ALD Pt at a low concentration (0.1 wt %) was as effective as that of the wet chemical deposition technique of CAER (specifically incipient deposition on a Co catalyst that had been prepared and calcined before the Pt deposition.) The ALD technique appeared to be nominally better than the incipient wetness technique that involved co-deposition of Pt and Co prior to calcination. The activation energy of the rate of CO conversion was tightly grouped about an average of 29.2 Kcal/mol when all of the Co-containing catalysts other than those with high Pt promoter levels were taken into account; this implies a uniform reaction mechanism. Catalysts containing Pt and Ru that were ALD-deposited on an ALD-Al 2 O 3 coated catalyst support were found to be relatively inactive. Additional tests were made with a low concentration (0.1 wt %) of Ru or Ir deposited on the reference Co catalyst. The Ir coated catalysts were particularly effective. In support of the above, there was an opportunity to undertake a study of cobalt/promoter/support interaction using the Advanced Photon Source (APS) of Argonne. A number of catalysts (including reference cobalt oxide and iron oxides) were tested using temperature programmed EXAFS/XANES experiments.

08 HYDROGEN↗

Manganese, Metallogenium, and Martian Microfossils

Manganese could easily be considered an abundant element in the Martian regolith, assuming that the composition of martian meteorites reflects the composition of the planet. Mineralogical analyses of 5 SNC meteorites have revealed an average manganese oxide concentration of 0.48%, relative to the 0.1% concentration of manganese found in the Earth's crust. On the Earth, the accumulation of manganese oxides in oceans, soils, rocks, sedimentary ores, fresh water systems, and hydrothermal vents can be largely attributed to microbial activity. Manganese is also a required trace nutrient for most life forms and participates in many critical enzymatic reactions such as photosynthesis. The wide-spread process of bacterial manganese cycling on Earth suggests that manganese is an important element to both geology and biology. Furthermore, there is evidence that bacteria can be fossilized within manganese ores, implying that manganese beds may be good repositories for preserved biomarkers. A particular genus of bacteria, known historically as Metallogenium, can form star-shaped manganese oxide minerals (called metallogenium) through the action of manganese oxide precipitation along its surface. Fossilized structures that resemble metallogenium have been found in Precambrian sedimentary formations and in Cretaceous-Paleogene cherts. The Cretaceous-Paleogene formations are highly enriched in manganese and have concentrations of trace elements (Fe, Zn, Cu, and Co) similar to modern-day manganese oxide deposits in marine environments. The appearance of metallogenium-like fossils associated with manganese deposits suggests that bacteria may be preserved within the minerals that they form. Additional information is contained in the original extended abstract.

Stein, L. Y.↗

Thermodynamic Stability and Site‐Specific Distribution of Graphitic and Pyridinic Nitrogen in Graphene Moiré on Ru(0001)

Abstract Graphene‐like materials are of interest for large‐scale hydrogen storage applications due to their lightweight, durable, and scalable properties. Nitrogen‐doping minimizes kinetic limitations in diffusion and recombination on surfaces, however, the role of graphitic nitrogen (GN) and pyridinic nitrogen (PN) is not well understood. Nitrogen‐doped graphene is synthesized on Ru(0001) using chemical vapor deposition (CVD) of pyridine and ion irradiation. Scanning tunneling microscopy (STM), x‐ray photoelectron spectroscopy (XPS), and density functional theory (DFT) are used to identify the structure, location, and thermodynamic stability of nitrogen species within the graphene moiré. CVD of pyridine results in a low nitrogen concentration (<0.1at%), while the post‐growth nitrogen ion irradiation allows us to increase the concentration further. The concentration of GN and PN is controlled by varying the ion dose and annealing temperature. Comparison of measured and simulated STM images of GN and PN yield an excellent agreement, allowing us to confidently establish that GN is preferentially located near the center of the Atop region, while PN is located in the valley region of the graphene moiré. This report explicitly confirms the site assignments and provides a foundation for the site synthesis and analysis of structural and electronic properties that drive the reactivity of N‐doped graphene.

Gedara, Buddhika S. A. [Physical and Computational↗

Extraction of americium, curium, and californium with LN resin from HCl and HNO 3

The uptake of 241 Am, 244 Cm and 249 Cf with LN resin was studied in HCl and HNO3 solutions with concentrations ranging from 0.02 to 2.5 M. There is high uptake at concentrations < 0.1 M in both acids for all three isotopes with decreasing uptake at higher concentrations and negligible extraction at ≥ 0.6 M. Californium has a higher extraction than americium and curium, which are extremely similar. Kinetics studies showed rapid uptake of all three isotopes. Here, column studies were performed to demonstrate the separation of 241 Am and 249 Cf, and a bulk separation including nine stable lanthanides along with 241 Am, 249 Cf, and 88 Y.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

TG-interacting factor transcriptionally induced by AKT/FOXO3A is a negative regulator that antagonizes arsenic trioxide-induced cancer cell apoptosis

Arsenic trioxide (ATO) is a multi-target drug approved by the Food and Drug Administration as the first-line chemotherapeutic agent for the treatment of acute promyelocytic leukemia. In addition, several clinical trials are being conducted with arsenic-based drugs for the treatment of other hematological malignancies and solid tumors. However, ATO's modest clinical efficacy on some cancers, and potential toxic effects on humans have been reported. Determining how best to reduce these adverse effects while increasing its therapeutic efficacy is obviously a critical issue. Previously, we demonstrated that the JNK-induced complex formation of phosphorylated c-Jun and TG-interacting factor (TGIF) antagonizes ERK-induced cyclin-dependent kinase inhibitor CDKN1A (p21{sup WAF1/CIP1}) expression and resultant apoptosis in response to ATO in A431 cells. Surprisingly, at low-concentrations (0.1–0.2 μM), ATO increased cellular proliferation, migration and invasion, involving TGIF expression, however, at high-concentrations (5–20 μM), ATO induced cell apoptosis. Using a promoter analysis, TGIF was transcriptionally regulated by ATO at the FOXO3A binding site (− 1486 to − 1479 bp) via the c-Src/EGFR/AKT pathway. Stable overexpression of TGIF promoted advancing the cell cycle into the S phase, and attenuated 20 μM ATO-induced apoptosis. Furthermore, blockage of the AKT pathway enhanced ATO-induced CDKN1A expression and resultant apoptosis in cancer cells, but overexpression of AKT1 inhibited CDKN1A expression. Therefore, we suggest that TGIF is transcriptionally regulated by the c-Src/EGFR/AKT pathway, which plays a role as a negative regulator in antagonizing ATO-induced CDKN1A expression and resultant apoptosis. Suppression of these antagonistic effects might be a promising therapeutic strategy toward improving clinical efficacy of ATO. - Highlights: • ATO-induced biphasic survival responses of cancer cells depend on low- or high-concentrations. • TGIF mediates low-concentration ATO-induced cancer cell proliferation, migration, and invasion. • ATO transcriptionally regulates TGIF expression via c-Src/EGFR/AKT/FOXO3A signalings. • Increased TGIF or AKT activation attenuates high-concentration ATO-induced CDKN1A expression and cellular apoptosis. • Suppression of these negative regulators might be a promising therapeutic strategy to improve therapeutic efficacy of ATO.

60 APPLIED LIFE SCIENCES↗

Transcriptional responses in the rat nasal epithelium following subchronic inhalation of naphthalene vapor

Male and female Fischer 344 rats were exposed to naphthalene vapors at 0 (controls), 0.1, 1, 10, and 30 ppm for 6 h/d, 5 d/wk, over a 90-day period. Following exposure, the respiratory epithelium and olfactory epithelium from the nasal cavity were dissected separately, RNA was isolated, and gene expression microarray analysis was conducted. Only a few significant gene expression changes were observed in the olfactory or respiratory epithelium of either gender at the lowest concentration (0.1 ppm). At the 1.0 ppm concentration there was limited evidence of an oxidative stress response in the respiratory epithelium, but not in the olfactory epithelium. In contrast, a large number of significantly enriched cellular pathway responses were observed in both tissues at the two highest concentrations (10 and 30 ppm, which correspond to tumorigenic concentrations in the NTP bioassay). The nature of these responses supports a mode of action involving oxidative stress, inflammation and proliferation. These results are consistent with a dose-dependent transition in the mode of action for naphthalene toxicity/carcinogenicity between 1.0 and 10 ppm in the rat. In the female olfactory epithelium (the gender/site with the highest incidences of neuroblastomas in the NTP bioassay), the lowest concentration at which any signaling pathway was significantly affected, as characterized by the median pathway benchmark dose (BMD) or its 95% lower bound (BMDL) was 6.0 or 3.7 ppm, respectively, while the lowest female olfactory BMD values for pathways related to glutathione homeostasis, inflammation, and proliferation were 16.1, 11.1, and 8.4 ppm, respectively. In the male respiratory epithelium (the gender/site with the highest incidences of adenomas in the NTP bioassay), the lowest pathway BMD and BMDL were 0.4 and 0.3 ppm, respectively, and the lowest male respiratory BMD values for pathways related to glutathione homeostasis, inflammation, and proliferation were 0.5, 0.7, and 0.9 ppm, respectively. Using a published physiologically based pharmacokinetic (PBPK) model to estimate target tissue dose relevant to the proposed mode of action (total naphthalene metabolism per gram nasal tissue), the lowest transcriptional BMDLs from this analysis equate to human continuous naphthalene exposure at approximately 0.3 ppm. It is unlikely that significant effects of naphthalene or its metabolites will occur at exposures below this concentration. - Highlights: • We investigated mode of action for carcinogenicity of inhaled naphthalene in rats. • Gene expression changes were measured in rat nasal tissues after 90 day exposures. • Support a non-linear mode of action (oxidative stress, inflammation, and proliferation) • Suggest a dose-dependent transition in the mode of action between 1.0 and 10 ppm • Transcriptional benchmark doses could inform point of departure for risk assessment.

60 APPLIED LIFE SCIENCES↗

Influence of CeO{sub 2} NPs on biological phosphorus removal and bacterial community shifts in a sequencing batch biofilm reactor with the differential effects of molecular oxygen

The effects of CeO{sub 2} nanoparticles (CeO{sub 2} NPs) on a sequencing batch biofilm reactor (SBBR) with established biological phosphorus (P) removal were investigated from the processes of anaerobic P release and aerobic P uptake. At low concentration (0.1 mg/L), no significant impact was observed on total phosphorus (TP) removal after operating for 8 h. However, at a concentration of 20 mg/L, TP removal efficiency decreased from 83.68% to 55.88% and 16.76% when the CeO{sub 2} NPs were added at the beginning of the anaerobic and aerobic periods, respectively. Further studies illustrated that the inhibition of the specific P release rate was caused by the reversible states of Ce{sup 3+} and Ce{sup 4+}, which inhibited the activity of exopolyphosphatase (PPX) and transformation of poly-β-hydoxyalkanoates (PHA) and glycogen, as well as the uptake of volatile fatty acids (VFAs). The decrease in the specific P uptake rate was mainly attributed to the significantly suppressed energy generation and decreased abundance of Burkholderia caused by excess reactive oxygen species. The removal of chemical oxygen demand (COD) was not influenced by CeO{sub 2} NPs under aerobic conditions, due to the increased abundance of Acetobacter and Acidocella after exposure. The inhibitory effects of CeO{sub 2} NPs with molecular oxygen were reduced after anaerobic exposure due to the enhanced particle size and the presence of Ce{sup 3+}. - Highlights: • CeO{sub 2} NPs (20 mg/L) had a notable toxicity effect on P removal in SBBR system. • The deteriorated SPRR was caused by the inhibited key enzyme activity (PPX). • The decreased SPUR was caused by the bacterial community shifts. • Ce ions converting and excess ROS generation are related toxicity mechanisms.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Kinetic Monte Carlo Simulation of Hydrogen Diffusion in Tungsten

Nuclear fusion is considered as the most promising sustainable energy source. If achieved, it could provide electricity to the mankind for millions of years. During the reaction, the fusion ash is continuously removed from the magnetic gap, the divertor region, and the divertor facing component is subjected to intense plasma bombardment. It is proposed to use tungsten as the divertor facing material, because it has low physical sputtering yield and superior thermomechanical properties. However, the high mobility of hydrogen in tungsten and the high bombardment flux bring the hydrogen isotopes deep into the tungsten tile. The presence of hydrogen in tungsten tends to weaken the gram boundaries and produce surface blistering. The ejection of tungsten particulates into the plasma core will cool the reaction and cease the fusion reactions. Therefore, it is important to have a detailed understanding of the hydrogen diffusion in tungsten bulk. The KMC method is a stochastic computer simulation to predict the time evolution of a certain system. Typically, at a given time, the system will evolve through a few possible paths with known probabilities. In each step, the KMC method analyzes the entire system and randomly determines the system evolving events based on all transition rates of all possible events and advance the physical time. This process is repeated till the simulation of the entire physical time is completed. In previous work, the authors developed a kinetic Monte Carlo (KMC) algorithm and program to simulate hydrogen diffusion process on tungsten reconstructed surface. In this article, this KMC method is extended to model the hydrogen diffusion in tungsten bulk. The diffusion coefficients are calculated and fitted to the Arrhenius equation. The result matches the experiment measurement very well. KMC diffusion simulation needs the locations of the hydrogen trapping sites, diffusion paths and the corresponding diffusion energy barriers. The hydrogen interstitial sites in tungsten crystal have been thoroughly studied by density function theory (DFT) and molecular dynamics (MD). Johnson and Carter used DFT to determine the preferred location of the hydrogen interstitial sites m tungsten crystal, which are the tetrahedral sites (T-sites) in body-centered-cubic (bcc) lattice surfaces. All T-sites are located on the surfaces of a lattice cell. There are four T-sites per surface and twelve T-sites per lattice cell. The hydrogen atoms diffuse by traveling from one T-site to one of its nearest four T-site neighbors. Thus, each T-site is surrounded by two neighbors on the same surface, and one neighbor on each of the two adjacent surfaces perpendicular to the surface holding the center T-site. The diffusion barrier between two neighboring T-sites was calculated to be 0.38 eV. Knowing the diffusion path, energy barrier, and the crystal structure, the KMC simulation is readily to be performed. Based on other researchers' DFT calculations, the hydrogen stable interstitial site in tungsten bulk is determined as the tetrahedral site on the surface of the bee lattice. Each T-site has 4 neighbors and the energy barrier between two adjacent T-sites are estimated to be 0.38 eV. Based on those facts and the KMC theory, a MATLAB program is developed to model the hydrogen diffusion in tungsten bulk. In the MATLAB program, substrate temperature, hydrogen concentration, physical time to be simulated, and the number of cycles are all customizable. To compare the KMC determined diffusion coefficients with experiment results in the literature, the simulations are performed for temperature 300 K - 2500 K and low hydrogen concentration (0.1%), mimicking the experiment condition. The calculated diffusion coefficients match the reference values measured by the experiment under low hydrogen concentration condition. The results are also fitted to the Arrhenius equation. The pre-exponential factor and the average activation energy in Arrhenius equation are obtained. The good agreement between simulation and experiment proves that the developed KMC algorithm truly reflect the well-established theory of interstitial hydrogens in tungsten. The developed program could easily be used to model the diffusion process and predict the diffusion coefficients under other concentrations and temperatures. This work is part of the ongoing development of hydrogen diffusion in tungsten integrating surface diffusion (previous work), bulk diffusion (this work), and adsorption/desorption on surface (future work)

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Influence of Concentration Gradients on Electroconvection at a Cation-Exchange Membrane Surface

Membrane-based systems, such as electrodialysis, play an important role in desalination and industrial separation processes. Electrodialysis uses alternating anion- and cation-exchange membranes with a perpendicular electric field to generate concentrated and diluate streams from a feed solution. It is known that under overlimiting current conditions, reduced charge and mass transfer at the membrane interface leads to regions of high ion depletion generating instability and vortices termed electroconvection. While electroconvective mixing is known to directly impact the separation efficiency of electrodialysis, the influence of ion concentration gradients across the membrane experienced in a functional electrodialysis system is not known. Here, we report the influence of ion concentration gradients across a cation exchange membrane (Nafion) that is both aligned with and opposed to the applied electric field. Experiments were conducted by coflowing NaCl solutions of different concentrations (0.1–100 mM) on each side of the membrane, and electroconvection was visualized with a fluorescence dye (Rhodamine 6G). Here, we obtained concentration profiles from fluorescence image data and systematically measured the thickness of the depletion boundary layer d BL under different conditions. We found smaller d BL values at a higher flow rate both with and without concentration gradients. Our results show that electroconvection is enhanced when the electric field is opposite to the direction of the concentration gradient.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of Anions on the Changes in the Structure and Adsorption Mechanism of Zirconium Species at the Muscovite (001)–Water Interface

Multivalent cations primarily exist as polynuclear hydroxo and oxyhydroxo clusters and/or nanoparticles (NPs) in aqueous environments, where their interactions with mineral surfaces can be influenced by complexing anions. In this work, we explored the distribution of tetravalent Zr adsorbed on the negatively charged basal surface of muscovite mica in four background electrolytes (0.1 M NaClO 4 , 0.1 M NaCl, 0.04 M Na 2 SO 4 , and 0.045 M Na 2 HPO 4 ) at constant pH (= 3), total Zr(IV) concentration (= 0.1 mM), and ionic strength (= 0.1 M). The results show that aqueous Zr speciation determined by reactions with anions controls the formation and structure of Zr-containing adsorbates on the mica surface. The Zr coverages measured by X-ray fluorescence (XRF) in ClO 4 - and Cl - systems were 1.3 and 2.1 Zr/A UC (where A UC = 46.72 Å 2 is the area of the unit cell of the mica (001) surface), respectively, and mostly remained unchanged during the reaction time from 6 to 50 h. In these conditions, Zr adsorption occurred both as small NPs (with an average height of ~4 nm observed by ex situ atomic force microscopy, AFM) and in a ~2 nm-thick molecular layer (observed by in situ resonant anomalous X-ray reflectivity, RAXR). In comparison, higher Zr coverages that increased with reaction time (i.e., from ~4 to ~7 Zr/A UC from 6 to 50 h reactions) were observed in the SO 4 2- system. Ex situ AFM showed that the Zr uptake in this system occurred predominantly as NPs that were ~5 to 15 nm tall and 20 to 40 nm wide, but no evidence of the interfacial molecular-layer formation was observed by RAXR. In the HPO 4 2– solution, all measurements unequivocally showed no significant Zr sorption, in stark contrast to the observations in the other solutions. Details of the Zr surface coverage and sorption modes are consistent with the known clustering of tetravalent Zr in solutions in the presence of these anions. These results reveal the critical impact of anions on the adsorption affinity and mechanism of Zr on the negatively charged mica surface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A solution NMR investigation into the impaired self-assembly properties of two murine amelogenins containing the point mutations T21→I or P41→T

Amelogenesis imperfecta describes a group of inherited disorders that results in defective tooth enamel. Two disorders associated with human amelogenesis imperfecta are the point mutations T21?I or P40?T in amelogenin, the dominant protein present during the early stages of enamel biomineralization. The biophysical properties of wildtype murine amelogenin (M180) and two proteins containing the equivalent mutations in murine amelogenin, T21?I (M180-I) and P41?T (M180-T), were probed by NMR spectroscopy. At low protein concentration (0.1 mM), M180, M180-I, and M180-T are predomi- nately monomeric at pH 3.0 in 2% acetic acid and neither mutation produces a major structural change. Chemical shift perturbation studies as a function of protein (0.1–1.8 mM) or NaCl (0–400 mM) concentra- tions show that the mutations affect the self-association properties by causing self-assembly at lower protein or salt concentrations, relative to wildtype amelogenin, with the largest effect observed for M180-I. Under both conditions, the premature self-assembly is initiated near the N-terminus, providing further evidence for the importance of this region in the self-assembly process. The self-association of M180-I and M180-T at lower protein concentrations and lower ionic strengths than wildtype M180 may account for the clinical phenotypes of these mutations, defective enamel formation.

amelogenesis↗

Colloidal Behavior of Plutonium Oxide in Concentrated Electrolyte Solutions

The Hanford Site in Washington State manages legacy high-level radioactive waste streams that display major chemistry and engineering challenges, including the high salt levels and pH values that correspond to conditions under which many classical concepts describing chemical reactivity cannot be applied. One particular challenge that needs to be tackled at Hanford is that Pu concentrations, [Pu], in the soluble phases of the tank wastes are higher than expected based on the solubility of crystalline PuO2, which is widely accepted to be caused by the formation of PuO2 colloid, consisting of nano- to submicron-sized particles (PuO2 NPs). Fundamental research underpinning the behavior of PuO2 NPs under conditions not only relevant to the Hanford tank waste but at high ionic strength in general is needed to reliably predict the chemical reactivity of PuO2 NPs and develop engineering solutions to safely and efficiently process high-level radioactive waste into forms suitable for long-term storage. In this work, we study the behavior of PuO2 NPs (particle size ~100 nm) under high ionic strength conditions by reacting it with highly concentrated (up to 5 M) salt solutions. We explore different electrolyte compositions to elucidate the impact of different anions (NO3-, Cl-, ClO4-, SO42-, C2O42-, CO32-) on the stability of PuO2 NP in the acidic and alkaline pH regime. PuO2 NP aggregation and precipitation as function electrolyte concentration is tracked by a combination of liquid scintillation counting, dynamic light scattering for determination of particle size distributions, and zeta potentials as a proxy for particle charge. At acidic pH, electrolytes containing non-coordinating anions, such as NaNO3, NaCl, and NaClO4 mostly stabilize PuO2 NPs over a large electrolyte concentration range, showing only subtle differences in their reactivity. Other electrolyte anions show a more pronounced effect on the PuO2 NP stability: SO42-, binds directly to the particles’ surface, reverses the particle charge, and precipitates the PuO2 NPs efficiently even at intermediate sulfate concentrations (>0.1 M). In contrast, C2O42- is found to lead to high [Pu] in solution, in the milli-molar range, even at mildly acidic pH (~4). Thermodynamic modeling of the dissolved Pu concentrations using PHREEQC is unable to predict the observed [Pu] in the acidic pH regime, supporting the influence of colloids in maintaining elevated [Pu]. It is noteworthy that the current thermodynamic databases do not include constants for colloidal Pu phases and cannot accurately predict many of the high ionic strength solutions relevant to this work. The mechanisms and models responsible for these observations will need further investigation in the future. At high pH values (~12), PuO2 NPs exhibits classical sol-gel chemistry, meaning that upon destabilization of the colloidal sol, for example by addition of concentrated NaOH, highly porous and viscid PuO2 coagulates are formed that consist of a three-dimensional network likely held together by physical interactions. The PuO2 NP coagulate shows no significant reversibility of the aggregation when contacted with concentrated brines; however, PuO2 NPs can be efficiently resuspended in solution by addition of diluted electrolytes, alkaline solutions containing high amounts of carbonate, or simple addition of water. Especially carbonate is shown to stabilize PuO2 NPs in solution at high pH, characterized by stable colloidal suspensions that are resistant against sedimentation during centrifugation. Thermodynamic modeling of the carbonate system was able to predict an increasing dissolved Pu concentration with increasing carbonate concentration. However, the model was profoundly sensitive to the fixed redox potential and does not include any thermodynamic constants for colloidal Pu species.

Neumann, Julia↗

Enhanced optical band-gap of ZnO thin films by sol-gel technique

Transparent ZnO thin films were prepared using different molar concentration (0.1 M, 0.2 M & 0.8 M) of zinc acetate on soda lime glass substrates by the sol-gel spin coating technique. The optical properties revealed that the transmittance found to decrease with increase in molar concentration. Absorption edge showed that the higher concentration film has increasingly red shifted. An increased band gap energy of the thin films was found to be direct allowed transition of ∼3.9 eV exhibiting their relevance for photovoltaic applications. The extinction coefficient analysis revealed maximum transmittance with negligible absorption coefficient in the respective wavelengths. The results of ZnO thin film prepared by sol-gel technique reveal its suitability for optoelectronics and as a window layer in solar cell applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗