Search NASA⌕ Search

SEARCH · Search NASA

Results for “salt concentration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Effect of electrode rinse solutions on the electrodialysis of concentrated salts

The data presented indicate that modest attention to the chemistry of the electrode rinse solution can yield as much as 56% improvement in process efficiency. When operating electrodialysis (ED) with salt concentrations greater than 10,000 mg/l (as NaCl) the amperage can be relatively high even at low voltages. To maximize the overall rate of ion transport from diluate to concentrate, there is a need to minimize resistances in the electrode cells since these can represent as much as 30% of the total resistances in the entire process and in this particular ED unit, represented resistance roughly equivalent to that within the membrane stack. This work describes the performance of a 10-cell pair, 200 cm 2 (0.02 m 2 ) per membrane, pilot ED unit operated in batch mode at 5 V potential. The feedstock to the stack was varied from 0.5% to 6% NaCl. Results from Volt-amp profiles (2.0–15 V) were used as the rationale for choosing the preferred electrode rinse solution, 90 g/l (kg/m 3 ) disodium sulfate at pH 12.5. The recommended solution of 30 g/l (kg/m 3 ) disodium sulfate at neutral pH was tested against stronger solutions (60, 90, and 120 g/l (kg/m 3 ) disodium sulfate) at neutral pH and with 1 g/l (kg/m 3 ) sodium hydroxide added to yield solutions at pH 12.5. There were stark differences in the performance of the ED unit between the solutions at pH 7 and those at pH 12.5. The slopes of the Volt-amp profiles improved indicating less resistance to ion flow at pH 12.5. Most of the difference can be attributed to the greater conductivity of sodium hydroxide compared to disodium sulfate, where even a modest addition of 1 g/l (kg/m 3 ) sodium hydroxide increased the conductivity of the solution between 8 and 20% depending on the concentration of disodium sulfate. Most notably, the initiation voltage was 2.39 ± 0.08 V with solutions at pH 7 and 1.99 V ± 0.04 V when the rinse solutions were around pH 12.5, a difference of around 0.42 V. Since the full batch runs were performed at 5.0 V, this 0.42 V differential represented a loss of 8% in process efficiency. A series of tests showed a shift in initiation voltage occurred between pH 11.5 and 12.5. Nernst equations for water electrolysis are coupled with a simple flux model that estimates the concentration of hydroxide and hydronium ions at the electrode surfaces. This model indicates that the potential demanded by the electrodes is directly linked to the current. Furthermore, there is a steep drop in the potential demanded by the anode when there is sufficient hydroxide available to generate oxygen from hydroxide as opposed to generation from water. The voltage demand is minimal at pH 12.5 and reflective of the reference standard voltage (just over 1.23 V predicted at 0.1 amps). However, the flux model predicts that the voltage demanded by the electrodes at pH 7 is 1.61 V at 0.1 amps (the lowest amperage measurable with the power pack). In conclusion, comparing this result to the reference standard (E 0 = -1.23 V) yields a satisfactory explanation for the observed difference below reference standard of 0.42 V.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Effect of Salt Concentration on the Interfacial Solvation Structure and Early Stage of Solid–Electrolyte Interphase Formation in Ca(BH 4 ) 2 /THF for Ca Batteries

The Ca 2+ solvation structure at the electrolyte/electrode interface is of central importance to understand electroreduction stability and solid–electrolyte interphase (SEI) formation for the novel multivalent Ca battery systems. Here, using an exemplar electrolyte, the concentration-dependent solvation structure of Ca(BH 4 ) 2 -tetrahydrofuran on a gold model electrode has been investigated with various electrolyte concentrations via electrochemical quartz crystal microbalance with dissipation (EQCM-D) and X-ray photoelectron spectroscopy (XPS). For the first time, in situ EQCM-D results prove that the prevalent species adsorbed at the interface is CaBH 4 + across all concentrations. As the salt concentration increases, the number of BH 4 – anions associated with Ca 2+ increases, and much larger solvated complexes such as CaBH 4 + ·4THF or Ca(BH 4 ) 3 – ·4THF form at the interface at high concentrations prior to Ca plating. Different interfacial chemistries lead to the formation of SEIs with different components demonstrated by XPS. High electrolyte concentrations reduce the solvent decomposition and promote the formation of thick, uniform, and inorganic-rich (i.e., CaO) SEI layers, which contribute to improved Ca plating efficiency and current density in electrochemical measurements.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Comparing Theoretical Salt Concentration Profiles in a Polymer Electrolyte with Experimental Measurements using Operando Raman Spectroscopy

Concentrated solution theory has furthered our understanding of ion transport in electrolytes. This theory can be used to predict salt concentration profiles under an applied current if the transport properties of the electrolyte (conductivity ( κ ), restricted diffusion coefficient ( D ), and the cation transference number with respect to the solvent velocity ( t + 0 )), and the thermodynamic factor ( T f ) are known. In this work, we provide the first study comparing the predicted salt concentration profiles with measurements based on operando Raman spectroscopy. Concentration polarization is asymmetrical; the increase in salt concentration near the positive electrode is a factor of two greater than the decrease in salt concentration near the negative electrode. We find qualitative agreement between theory and experiment. Further work is needed to resolve the quantitative differences.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Strong stretching theory for pH-responsive polyelectrolyte brushes in large salt concentrations

Here, we develop a theory for describing the thermodynamics, configuration, and electrostatics of strongly-stretched, pH-responsive polyelectrolyte (PE) brushes in the presence of large salt concentrations. The aim of the paper, therefore, is to study the properties of a PE brush in a salt concentration regime (namely, large concentrations of several molars) that has been hitherto unexplored theoretically in the context of PE brushes but can be routinely encountered in molecular scale simulations of the problem. The brushes are modelled using our recently developed augmented Strong Stretching Theory (SST), while the effect of the presence of the large salt concentration is accounted for by including the contributions of three different types of non-Poisson–Boltzmann (non-PB) effects to the free energy description of the PE brush induced electric double layer (EDL). These non-PB effects are ionic non-mean-field ion–ion correlations, solvent polarization, and the finite size effect of the ions and water dipoles. We study the individual influences of these different effects and show that the ion–ion correlations and solvent polarization effect reduce the brush height which consequently enhances the monomer density and leads to an electrostatic potential distribution of the brush induced EDL that has a larger magnitude at near-wall locations and becomes zero at shorter distances from the wall. The finite size effect, on the other hand, increases the brush height and therefore, weakens the monomer density and leads to a smaller near-wall magnitude of the EDL potential that becomes zero at larger distances from the wall. In time, we consider the impact of all the three non-PB effects simultaneously and show that the ion–ion correlations and solvent polarization effect dominate the size effects and dictate the overall brush configuration and the EDL electrostatics. We also point out that the influence of all the three non-PB effects becomes the largest for a larger salt concentration and a smaller bulk pH. Finally, we compare our theoretical predictions with those obtained from our recently developed all-atom MD simulation model and obtain an excellent match.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Effect of salt concentration profiles on protrusion growth in lithium-polymer-lithium cells

In this report, the formation of dendrites and other protrusions on lithium metal anodes is a subject of continued interest due to the potential to incorporate these anodes in next-generation rechargeable batteries with increased energy densities. Solid polymer electrolytes show improved stability against lithium metal compared to liquid carbonate electrolytes. We have studied the effect of salt concentration on the formation of protrusions formed on electrodeposited lithium through a rigid block copolymer electrolyte, polystyrene-block-poly(ethylene oxide) (PS-b-PEO or SEO), in a lithium-lithium symmetric cell. The cell lifetime decreases by a factor of 100 when salt concentration is increased by a factor of 5. Our main objective is to understand the reason for this observation. We show that this decrease is not due to a salt-induced change of the morphology of the block-copolymer electrolyte, nor is it due to a salt-induced change of mechanical properties. We use an approach based on Newman's concentrated solution theory to fully characterize ion transport in the block-copolymer electrolyte, and report the conductivity, salt diffusion coefficient, cation transference number, and thermodynamic factor. Neither cell lifetime nor protrusion density in failed cells correlate with any of these electrochemical parameters. However, the electrochemical parameters can be used to predict salt concentration profiles in our symmetric cells. We posit that an important parameter in protrusion growth is the magnitude of the salt concentration gradient, Δ. We observe a direct correlation between Δ and lithium protrusion growth.

25 ENERGY STORAGE↗
DOE OSTI2021

Ion Pairing, Clustering and Transport in a LiFSI-TMP Electrolyte as Functions of Salt Concentration using Molecular Dynamics Simulations

Battery capacity is highly related to ion-pairing mechanisms in electrolytes, since a cluster formation can lead to dead Li formation, reducing the number of charge carriers and leading to capacity fading. We use molecular dynamics simulations to model an electrolyte comprising trimethyl phosphate (TMP) solvent and a lithium bis(fluorosulfonyl)imide (LiFSI) salt, exploring effects of salt concentration on solvation and ion-transport. We simulate the LiFSI-TMP electrolyte for salt concentrations of 0.7, 1.43 and 3.82 molar. A statistical analysis was performed to study ion-pairing, clustering, diffusivity, conductivity, and coordination of Li-ions, providing insights into relations between molecular structures and transport properties. Molecular structure of ionic components changes as concentration increases, from a predominant solvent separated ion pair (SSIP) and contact ion pair (CIP) to aggregate salt (AGG) and ionic cluster formation. Given the formation of the ionic cluster, the diffusion mechanism followed by Li-ions changes from a hopping/exchange to a vehicular mechanism as concentration increases; this is reflected in a decrease of ionic conductivities. Ionicity was also calculated to reveal how the ionic motion changes from an uncorrelated to a correlated one as the salt concentration increases. Furthermore, we also compared our results with experimental calculations performed for similar electrolyte systems

25 ENERGY STORAGE↗
DOE OSTI2022

Comparing measurement of limiting current in block copolymer electrolytes as a function of salt concentration with theoretical predictions

Optimizing electrolyte performance is crucial for the widespread adoption of electrochemical energy storage. We demonstrate that limiting current provides a robust criterion for determining the optimum electrolyte. Experiments were conducted on rigid block copolymer electrolytes comprising mixtures of polystyrene-block-poly(ethylene oxide) copolymer (SEO) and lithium bis(trifluoromethanesulfonyl) imide salt (LiTFSI) over a salt concentration range from r av = 0.04 to r av = 0.20 (r av is the molar ratio of lithium ions to ethylene oxide). Here we show that the maximum limiting current density is 4.3 mA cm –2 at r av = 0.12. The dependence of limiting current on salt concentration is in good agreement with predictions from Newman's concentrated solution theory with no adjustable parameters.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Role of Salt Concentration on Interphase Dynamics and Chemistry of Silicon Anodes during Electrochemical Cycling

We investigated the chemistry and structure of the solid electrolyte interphase (SEI) grown over a silicon anode as a function of the lithium salt concentration. In these experiments, in situ neutron reflectivity measurements were performed to measure the thickness and composition of the SEI formed from 1.0 and 5.5 M lithium bis(trifluoromethane)sulfonimide (LiTFSI) in standard ethylene carbonate:dimethyl carbonate electrolytes. These measurements reveal the formation of a 350+ Å thick SEI layer that is predominantly organic (∼80%) and dimensionally stable when using a 1.0 M salt solution. In contrast, increasing the salt concentration to 5.5 M resulted in an SEI that exhibited thickness changes from 100 to 375 Å and became up to 30% inorganic. In conclusion, these compositional and structural changes point to the role of salt speciation on the resulting passivation of silicon electrodes and indicate the need to form more organic-like passivation layers to promote the calendar life of silicon anodes.

Electrodes↗
DOE OSTI2020

Ultrastructure of Critical-Gel-like Polyzwitterion–Polyoxometalate Complex Coacervates: Effects of Temperature, Salt Concentration, and Shear

The structure of unconventional complex coacervates, such as polymer-nonpolymer complex coacervates, remains less investigated than that of the conventional coacervates formed between oppositely charged polyelectrolytes with symmetric charge species. Yet, their microscopic structural organization is important to further elucidate the mechanism of liquid-liquid-phase separation processes upon complexation. In this work, we characterize the microstructural organization of complex coacervates formed between inorganic polyoxometalate (POM) and polyzwitterion by small-angle X-ray scattering (SAXS) with in situ temperature and shear control. Furthermore, despite the apparent transparent and homogeneous morphology of dense coacervates as observed by optical microscopy, our previous results (Macromolecules 2018, 51, 22, 9405-9411) suggest that dense polyzwitterion-POM coacervates exhibit critical-gel-like networks containing both complex-poor region (mesh pore) and complex-rich region (connective network). SAXS results as reported in this work support that the complex-rich region is actually in the form of loosely packed POM aggregates linked by polyzwitterion, designated as complex particles. The structure of aggregating complex particles is further examined against varied composition and salt concentrations, temperature, and shear, thanks to the high X-ray scattering contrast of POMs from that of other components in the coacervates. The complex particles in the dense coacervates appear to grow with more tightly packed POM aggregates with increasing POM-to-polyzwitterion concentration ratio, in contrast to more loosely packed POM aggregates with decreasing salt concentration. Conversely, increasing temperature could result in smaller complex particles containing more loosely packed POM aggregates, consistent with temperature-dependent viscoelasticity of dense coacervates. Furthermore, such POM-based hybrid dense coacervates exhibit intriguing strain-hardening behavior, resulting from shear-enhanced POM packing inside the complex particles. Distinct from the shear-thinning behavior of most conventional crosslinked polymeric networks, the strain-hardening property combined with thermal- and salt-responsive characteristics of polyzwitterion-POM coacervates could broaden the applications of hybrid organic-inorganic macroion coacervates as smart functional materials working under extreme environmental conditions.

36 MATERIALS SCIENCE↗
NASA NTRS2002

AFM Studies of Salt Concentration Effects on the (110) Surface Structure of Tetragonal Lysozyme Crystals

Previous high resolution AFM studies of the (110) surface of tetragonal chicken egg white lysozyme crystals had shown that only one of two possible molecular surfaces is present, those constituting the completed 43 helices. These suggested that the crystal growth process was by the solution-phase assembly of the growth units, which then attach to the surface. However, the best fit for the imaged surfaces, vs. those predicted based upon the bulk crystallographic coordinates, were obtained when the packing about the 43 helices was "tightened up", while maintaining the underlying crystallographic unit cell spacing. This results in a widening of the gap between adjacent helices, and the top- most layer(s) may no longer be in contact. We postulated that the tightened packing about the helices is a result of the high salt concentrations in the bulk solution, used to crystallize the protein, driving hydrophobic interactions. Once the crystal surface is sufficiently buried by subsequent growth layers the ratio of salt to protein molecules decreases and the helices relax to their bulk crystallographic coordinates. The crystal surface helix structure is thus a reflection of the solution structure, and the tightness of the packing about the 43 helices would be a function of the bulk salt concentration. AFM images of the (110) surface of tetragonal lysozyme crystals grown under low (2%) and high (5%) NaCl concentrations reveal differences in the packing about the 43 helices consistent with the above proposal.

Pusey, Marc Lee↗
DOE OSTI2023

Effects of γ-Irradiation, Cation Size, and Salt Concentration on the Aggregation of Boehmite Nanoplatelets

The effects of radiation on the aggregation of nanoplatelets of aluminum oxyhydroxide (boehmite) in slurries of M 1+ cation nitrates has been observed using tumbler small- and ultra-small-angle neutron scattering. Nitrate solutions of H, Li, Na, K, and Rb at concentrations of 10 -5 , 10 -3 , 10 -1 , 2, and 4 molal were compared to the results for pure H 2 O. Primary aggregates consisting of small stacks of boehmite platelets that form immediately after the boehmite is placed in water are smaller for irradiated boehmite than the pristine material. Here, the primary aggregates for irradiated boehmite also appear to have a rougher surface than those observed for unirradiated materials. Both results are possibly due to breaking of the surface OH species and a neutralization of the surface. At low salt concentrations, the pH of the irradiated boehmite slurries is lower than that of the corresponding pristine material indicating that irradiated boehmite adsorbs fewer protons or more hydroxide onto its surface than the pristine boehmite. Increasing the salt concentration decreases the pH to near neutral at 7 due to screening of the electric double layer at the solid/liquid interface. Irradiation does not seem to affect the size of secondary aggregates formed from the aggregation of primary aggregates or of the overall size of the primary aggregates.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

A Green, Fire–Retarding Ether Solvent for Sustainable High–Voltage Li–Ion Batteries at Standard Salt Concentration

Lithium-ion batteries (LIBs) are increasingly encouraged to enhance their environmental friendliness and safety while maintaining optimal energy density and cost-effectiveness. Although various electrolytes using greener and safer glyme solvents have been reported, the low charge voltage (usually lower than 4.0 V vs Li/Li + ) restricts the energy density of LIBs. Herein, tetraglyme, a less-toxic, non-volatile, and non-flammable ether solvent, is exploited to build safer and greener LIBs. It is demonstrated that ether electrolytes, at a standard salt concentration (1 m), can be reversibly cycled to 4.5 V vs Li/Li + . Anchored with Boron-rich cathode-electrolyte interphase (CEI) and mitigated current collector corrosion, the LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) cathode delivers competitive cyclability versus commercial carbonate electrolytes when charged to 4.5 V. Synchrotron spectroscopic and imaging analyses show that the tetraglyme electrolyte can sufficiently suppress the overcharge behavior associated with the high-voltage electrolyte decomposition, which is advantageous over previously reported glyme electrolytes. The new electrolyte also enables minimal transition metal dissolution and deposition. NMC811||hard carbon full cell delivers excellent cycling stability at C/3 with a high average Coulombic efficiency of 99.77%. In conclusion, this work reports an oxidation-resilient tetraglyme electrolyte with record-high 4.5 V stability and enlightens further applications of glyme solvents for sustainable LIBs by designing Boron-rich interphases.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Understanding the effect of salt concentrations on fast charging performance of Li-ion cells

Here, different lithium salt (lithium bis(fluorosulfonyl) imide (LiFSI)/LiPF 6 9/1 mol ratio) concentrations in carbonate electrolyte were studied on the fast charging performance of LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622)/graphite pouch cells. The cells with electrolyte concentration from 0.75 M to 1.50 M showed similar fast charging capabilities. Further increase of the concentration to 1.75 M and 2.00 M decreased the attainable capacity in fast charging. In the long-term cycling test, the capacity retention after 200 fast charging cycles increased with the increase of salt concentration in electrolyte. Cells with 1.5 M electrolyte showed the best overall performance in fast charging capacity and long-term cycling. Li platings were observed in the cells with 0.75 M, 1.00 M and 1.25 M electrolyte. It was improved with greatly reduced Li plating area in 1.50 M, and no Li plating at all in 1.75 M and 2.00 M electrolyte. Post-mortem analysis such as neutron powder diffraction (NPD) and X-ray photoelectron spectroscopy (XPS) were used to characterize the electrode after cycling. It suggests that electrolyte concentration needs to be optimized for a given cell configuration with specific electrode and loading.

25 ENERGY STORAGE↗
DOE OSTI2021

Local molecular environment drives speciation and reactivity of ion complexes in concentrated salt solution

The speciation and reactivity of aqueous salt solutions are important for a wide variety of applications. However, application of this information is inhibited by broad disagreement about composition, mechanisms, and structure in concentrated solutions especially. Here, neutron diffraction with isotopic substitution measurements on aqueous zinc chloride solutions are used to calibrate molecular dynamics simulations that include effective electronic polarization. This allows us to probe the origin of speciation and reactivity of zinc chloride-water ion complexes, ZnCl x (H 2 O) y 2-x (x ≤ 4 and y ≤ 6), by comparing the reactivity of species in concentrated (4.5 m) and dilute (0.01 m) conditions. Within the concentrated solution, it is found that the extended solvation environment is dominated by solvent-separated ion complexes whose presence increases the free energy of activation for interconversion of species while simultaneously enhancing their thermodynamic stability. This concentration-dependent reactivity and stability suggests that other reactions, such as the nucleation of solid phases, will also be affected.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Effects of Salt Concentration, Ionic Strength, and Water Activity on the Growth of a WIPP Archaeal Isolate, Halobacterium sp.

An extremely halophilic archaeon (Halobacterium sp., WIPP strain), isolated from WIPP halite, was tested for its ability to grow in media containing various combinations of sodium and magnesium chloride that influenced overall ionic strength and water activity. Halobacterium sp. grew well in most tested salt combinations, and its growth appeared to depend more upon the relative contribution of sodium to overall ionic strength than on other parameters. Growth rates were highest when media consisted of at least 2 M NaCl and lowest when NaCl dropped below 20% of the ionic strength (usually less than 0.5 M). High magnesium concentrations (1 and 1.5 M MgCl 2 ) did not prevent Halobacterium sp. growth, as long as the sodium contribution was sufficient. Water activity was not a definitive factor in determining growth, because this value did not reach an extreme lower limit in the experimental media.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Effects of Salt Concentration, Ionic Strength, and Water Activity on the Growth of a WIPP Archaeal Isolate, Halobacterium sp.

An extremely halophilic archaeon ( Halobacterium sp., WIPP strain), isolated from WIPP halite, was tested for its ability to grow in media containing various combinations of sodium and magnesium chloride that influenced overall ionic strength and water activity. Halobacterium sp. grew well in most tested salt combinations, and its growth appeared to depend more upon the relative contribution of sodium to overall ionic strength than on other parameters. Growth rates were highest when media consisted of at least 2 M NaCl and lowest when NaCl dropped below 20% of the ionic strength (usually less than 0.5 M). High magnesium concentrations ( 1 and 1.5 M MgCh 2 ) did not prevent Halobacterium sp. growth, as long as the sodium contribution was sufficient. Water activity was not a definitive factor in determining growth, because this value did not reach an extreme lower limit in the experimental media.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗