Sidelobe suppression techniques for reflector antennas on satellites
Sidelobe suppression for satellite reflector antennas by heavy taper, blockage compensation and active zone techniques, noting net antenna gain enhancement
Goebels, F. J., Jr.↗
SEARCH · Search NASA
Results for “satellite reflector antennas”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A microstrip array feed for land mobile satellite reflector antennas
A circularly polarized feed array for a spacecraft reflector antenna is described that was constructed by using linearly polarized microstrip elements. The array has seven subarrays which form a single cluster as part of a large overlapping cluster reflector feed array. Each of the seven subarrays consists of four linearly polarized microstrip elements. The array achieved a better than 0.8-dB axial ratio at the array pattern peak and better than 3 dB antenna gain to 20 degrees from the peak, across a 7.5 percent frequency bandwidth. A teardrop-shaped feed probe was used to achieve wideband input impedance matching for the relatively thick microstrip substrate. The low impedance and axial ratio bandwidths were achieved using a relatively thick honeycomb substrate with the impedance-matching feed probes.
Huang, John↗
K- and Ka-band mobile-vehicular satellite-tracking reflector antenna system for the NASA ACTS mobile terminal
This paper describes the development of the K- and Ka-band mobile-vehicular satellite-tracking reflector antenna system for NASA's ACTS Mobile Terminal (AMT) project. ACTS is NASA's Advanced Communications Technology Satellites. The AMT project will make the first experimental use of ACTS soon after the satellite is operational, to demonstrate mobile communications via the satellite from a van on the road. The AMT antenna system consists of a mechanically steered small reflector antenna, using a shared aperture for both frequency bands and fitting under a radome of 23 cm diameter and 10 cm height, and a microprocessor controlled antenna controller that tracks the satellite as the vehicle moves about. The RF and mechanical characteristics of the antenna and the antenna tracking control system are discussed. Measurements of the antenna performance are presented.
Densmore, Art↗
K- and Ka-band Mobile-Vehicular Satellite-Tracking Reflector Antenna System for the NASA ACTS Mobile Terminal
This paper describes the development of the K- and Ka-band mobile-vehiclular satellite-tracking reflector antenna system for NASA's ACTS Mobile Terminal (AMT) project. ACTS is NASA's Advanced Communications Tehcnology Satellite.
K-Band↗
Scan performance of dual offset reflector antennas for satellite communications
The basic numerical steps of a method to analyze dual offset reflector antennas are reviewed. The technique employs an alternative approach to calculating the secondary pattern of an arbitrarily shaped offset dual reflector antenna, and is based on the application of the geometrical theory of diffraction from the subreflector and physical optics (PO) scattering from the main reflector. The PO integral is evaluated using the Jacobi-Bessel series expansions, and numerical results are presented for the off-axis scan performance of an offset clear aperture Cassegrain antenna. Results indicate that the equivalent paraboloid concept can be used to determine the location of displaced feed and define the local optimal focal plane, and the scan performance of the Cassegrain reflector can be improved if the feed is located on the true opimal surface.
Rahmat-Samii, Y.↗
Satellite-Tracking Millimeter-Wave Reflector Antenna System For Mobile Satellite-Tracking
A miniature dual-band two-way mobile satellite-tracking antenna system mounted on a movable vehicle includes a miniature parabolic reflector dish having an elliptical aperture with major and minor elliptical axes aligned horizontally and vertically, respectively, to maximize azimuthal directionality and minimize elevational directionality to an extent corresponding to expected pitch excursions of the movable ground vehicle. A feed-horn has a back end and an open front end facing the reflector dish and has vertical side walls opening out from the back end to the front end at a lesser horn angle and horizontal top and bottom walls opening out from the back end to the front end at a greater horn angle. An RF circuit couples two different signal bands between the feed-horn and the user. An antenna attitude controller maintains an antenna azimuth direction relative to the satellite by rotating it in azimuth in response to sensed yaw motions of the movable ground vehicle so as to compensate for the yaw motions to within a pointing error angle. The controller sinusoidally dithers the antenna through a small azimuth dither angle greater than the pointing error angle while sensing a signal from the satellite received at the reflector dish, and deduces the pointing angle error from dither-induced fluctuations in the received signal.
Densmore, Arthur C.↗
A satellite-tracking millimeter-wave reflector antenna system for mobile satellite-tracking
A miniature dual-band two-way mobile satellite tracking antenna system mounted on a movable ground vehicle includes a miniature parabolic reflector dish having an elliptical aperture with major and minor elliptical axes aligned horizontally and vertically, respectively, to maximize azimuthal directionality and minimize elevational directionality to an extent corresponding to expected pitch excursions of the movable ground vehicle. A feed-horn has a back end and an open front end facing the reflector dish and has vertical side walls opening out from the back end to the front end at a lesser horn angle and horizontal top and bottom walls opening out from the back end to the front end at a greater horn angle. An RF circuit couples two different signal bands between the feed-horn and the user. An antenna attitude controller maintains an antenna azimuth direction relative to the satellite by rotating it in azimuth in response to sensed yaw motions of the movable ground vehicle so as to compensate for the yaw motions to within a pointing error angle. The controller sinusoidally dithers the antenna through a small azimuth dither angle greater than the pointing error angle while sensing a signal from the satellite received at the reflector dish, and deduces the pointing angle error from dither-induced fluctuations in the received signal.
Densmore, Arthur C.↗
Near field interaction of microwave signals with a bounded plasma plume
The objective was to study the effect of the arcjet thruster plume on the performance of an onboard satellite reflector antenna. A project summary is presented along with sections on plasma and electromagnetic modeling. The plasma modeling section includes the following topics: wave propagation; plasma analysis; plume electron density model; and the proposed experimental program. The section on electromagnetic modeling includes new developments in ray modeling and the validation of three dimensional ray results.
Ling, Hao↗
Effect of an arcjet plume on satellite reflector performance
The effect of an arcjet plume on the performance of satellite reflector antennas is studied. The arcjet plume is modeled as a weakly ionized plasma. The spatial permittivity distribution of the plume is approximated using the measured electron density profile and a cold plasma model. Geometrical optics is applied to determine the ray paths as well as the transmitted fields through the inhomogeneous plume. The ray optics results are compared against several exact solutions for scattering from inhomogeneous dielectrics, and good agreement is observed for sufficiently large scatterer size. The far-field antenna patterns of the reflector in the presence of the plume are calculated from the transmitted ray fields using a ray-tube integration scheme. For arcjet prototypes in the 1-kW class, the plume effect on the antenna performance is small. As the electron density increases, the main beam and sidelobe level gradually degrade. The main beam also tends to squint away from the plume region.
Ling, Hao↗
Electrical performance of wire mesh for spacecraft deployable reflector antennas
Mobile satellite communications systems require large, high gain antennas at the spacecraft to minimize the antenna gain and power requirements for mobile user elements. The use of a deployable reflector antenna for these applications provides a lightweight system that can be compactly stowed prior to deployment on orbit. The mesh surface material is a critical component in the deployable reflector antenna design. The mesh is required to provide the desired electrical performance as well as the mechanical properties that are necessary to deploy and maintain the reflector surface on orbit. Of particular interest in multi-channel communications applications is the generation of Passive InterModulation (PIM) products at the reflector surface that can result in interference in the receive band. Wire mesh was specifically identified by some as having a high potential for PIM generation based solely on the existence of nonpermanent metal to metal contacts at the junctions that are inherent in the mesh design. There are a number of other factors, however, that reduce the likelihood of PIM occurring at the mesh reflector surface. Experimental data presented demonstrate that mesh PIM generation is not significant for typical applications. PIM and reflectivity performance of wire mesh composed of gold plated molybdenum wire in a tricot knit are described. This type of mesh was successfully used for the deployable Single Access Antennas of the Tracking and Data Relay Satellite System.
Turner, Greg↗
An experimental 20/30 GHz communications satellite conceptual design employing multiple-beam paraboloid reflector antennas
An experimental 20/30 GHz communications satellite conceptual design is described which employs multiple-beam paraboloid reflector antennas coupled to a TDMA transponder. It is shown that the satellite employs solid state GaAs FET power amplifiers and low noise amplifiers while signal processing and switching takes place on-board the spacecraft. The proposed areas to be served by this satellite would be the continental U.S. plus Alaska, Hawaii, Puerto Rico, and the Virgin Islands, as well as southern Canada and Mexico City. Finally, attention is given to the earth stations which are designed to be low cost.
Goldman, A. M., Jr.↗
Active feed array compensation for reflector antenna surface distortions
The feasibility of electromagnetic compensation for reflector antenna surface distortions is investigated. The performance characteristics of large satellite communication reflector antenna systems degrade as the reflector surface distorts, mainly due to thermal effects from solar radiation. The technique developed can be used to maintain the antenna boresight directivity and sidelobe level independent of thermal effects on the reflector surface. With the advent of monolithic microwave integrated circuits (MMIC), a greater flexibility in array fed reflector antenna systems can be achieved. MMIC arrays provide independent control of amplitude and phase for each of the many radiating elements in the feed array. By assuming a known surface distortion profile, a simulation study is carried out to examine the antenna performance as a function of feed array size and number of elements. Results indicate that the compensation technique can effectively control boresight directivity and sidelobe level under peak surface distortion in the order of tenth of a wavelength.
Acosta, Roberto J.↗
Satellite-aided mobile radio concepts study: Concept definition of a satellite-aided mobile and personal radio communication system
The satellite system requires the use of a large satellite antenna and spacecraft array power of about 12 kW or more depending on the operating frequency. Technology developments needed include large offset reflector multibeam antennas, satellite electrical power sybsystems providing greater than 12 kW of power, signal switching hardware, and linearized efficient solid state amplifiers for the satellite-aided mobile band. Presently there is no frequency assignment for this service, and it is recommended that an allocation be pursued. The satellite system appears to be within reasonable extrapolation of the state of the art. It is further recommended that the satellite-aided system spacecraft definition studies and supporting technology development be initiated.
Anderson, R. E.↗
Segmented Solid Surface Reflector Concentrically Stacked With Tubular Shape Memory Composite Hinges
A new architecture for solid surface reflector antennas scalable to sizes greater than 10 m is presented. The design uses compact, light, and simple advanced deployable structures to create sub-reflectors that can be assembled in space into larger units using a robotic arm. The seven-panel hexagonal sub-reflector is divided into hexagonal panels that stack concentrically and vertically. The central panel is connected to each side panel on the back side by a pair of tubular shape memory composite hinges that enable the required deployment kinematics with controlled dynamics. A secondary mechanism closes the interpanel gap. The focus of the paper is on the development of the sub-reflector elements, namely the tubular hinges that use embedded heaters and sensors for triggering and control, the actuation mechanisms, and the lightweight sandwich construction reflector panels. A parametric study using finite element analyses was conducted to assess how design features of the hinge affect its stowage and deployment dynamics. The preliminary component fabrication and testing results for the two-panel assembly breadboard model are outlined. Finally, the results of the test campaign with the brassboard reflector model are presented. A comparison of deployed reflector surface deviation between the measured surface after the stowage and deployment process and the pre-test scans and the nominal surface revealed root mean square errors of less than 1 mm, as required by X-band radiofrequency transmission.
gravity offloading↗
Segmented Hexagonal Antenna Reflector Concentrically Stacked Using Shape Memory Composite Tubular Hinges
A new architecture for solid surface reflector antennas scalable to sizes greater than 10 m is presented. The design uses compact, light, and simple advanced deployable structures to create sub-reflectors that can be assembled in space into larger units using a robotic arm. The seven-panel hexagonal sub-reflector is divided into hexagonal panels that stack concentrically and vertically. The central panel is connected to each side panel on the back side by a pair of tubular shape memory composite hinges that enable the required deployment kinematics with controlled dynamics. A secondary mechanism closes the interpanel gap. The focus of the paper is on the development of the sub-reflector elements, namely the tubular hinges that use embedded heaters and sensors for triggering and control, the actuation mechanisms, and the lightweight sandwich construction reflector panels. A parametric study using finite element analyses was conducted to assess how design features of the hinge affect its stowage and deployment dynamics. The preliminary component fabrication and testing results for the two-panel assembly breadboard model are outlined. Finally, the results of the test campaign with the brassboard reflector model are presented. A comparison of deployed reflector surface deviation between the measured surface after the stowage and deployment process and the pre-test scans and the nominal surface revealed root mean square errors of less than 1 mm, as required by X-band radiofrequency transmission.
gravity offloading methods↗
SMA applications in an innovative multishot deployment mechanism
An innovative Deployment and Retraction hinge Mechanism (DARM) in the frame of a technological program is examined. The mechanism includes two restraint/release devices, which enable it to be stable in its stowed or deployed position while sustaining all associated loads, and to carry its payload by remote command. The main characteristics of the DARM are as follows: deployment and retraction movements are spring actuated; the available amount of functional sequences is almost unlimited; and no use of electrical motors is made. These features were accomplished by: the application of a special kinematic scheme to the mechanical connection between the spring motor and the swivel head arm; and the use of shape memory alloys (SMA) actuators for both release and spring recharge functions. DARM is thus a mechanism which can find many applications in the general space scenario of in-orbit maintenance and servicing. In such a frame, the DARM typical concept, which has a design close to very simple one-shot deployment mechanisms, has a good chance to replace existing analog machines. Potential items that could be moved by DARM are: booms for satellite instruments; antenna reflector tips; entire antenna reflectors; and solar panels.
Stella, D.↗
A Ka-Band (26 GHz) Circularly Polarized 2x2 Microstrip Patch Sub-Array with Compact Feed
A Ka-Band (26 gigahertz) 2 by 2 sub-array with square-shaped microstrip patch antenna elements having two truncated corners for circular polarization (CP) is presented. In addition, the layout for a new compact microstrip feed network for the sub-array is also presented. The compact feed network offers a footprint size reduction of near 60 percent over traditional sub-array at 26 gigahertz. Experimental data indicates that a truncation amount a equals 0.741 millimeters for an isolated patch element results in a return loss (S (sub II)) of minus 35 decibels at 26.3 gigahertz. Furthermore, the measured S (sub II) for the proof-of-concept sub-array with the above elements is better than minus 10.0 decibels at 27.7 gigahertz. However, the impedance match and the operating frequency can be fine-tuned to 26 gigahertz by adjusting the feed network dimensions. Lastly, good agreement is observed between the measured and simulated S (sub II) for the subarray for both right hand and left hand CP. The goal of this effort is utilize the above sub-array as a building block for a larger N by N element array, which would serve as a feed for a reflector antenna for satellite communications.
Microstrip↗
Multibeam antenna for 30/20 GHz advanced communications satellite using offset shaped, dual reflector surfaces
Progress in the Antenna Technology Study being performed by NASA to characterize an antenna system with a scaning beam with a half-power beam diameter of around 0.3 deg and a minimum width over which the sidelobes stay below the -30 dB level is reported. Continuous U.S. (CONUS) coverage is desired by the satellite antenna system, with 10-20 fixed beams for trunk coverage and a rapidly scanned narrow beam for customer premises. The design specifies 24 beamwidths from east to west and 10 beamwidths from south to north. Reflector parameters have been identified to optimally focus all beams from a planar feed array. An example of coverage expected with the design demonstrates optimized beams for Seattle, Oklahoma City, and Miami, with -3 dB contours in circles 0,25 deg in diameter and a peak directivity of 55 dB. Experimental work was scheduled for 1983.
Smoll, A. E.↗