Search NASA⌕ Search

SEARCH · Search NASA

Results for “siltstone”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Mobilization of Metals from Eau Claire Siltstone and the Impact of Oxygen under Geological Carbon Dioxide Sequestration Conditions

Geologic CO2 sequestration (GCS) has been proposed as a viable strategy to reduce anthropogenic CO2 emission; however, the increased cost that will be incurred by fossil energy production facilities is a deterrent to implementation of this technology. Allowing impurities in the effluent CO2 stream could result in significant financial and energy savings for CO2 capture and separation. However, impurities such as O2 have the potential to influence the redox state and alter the geochemical interactions that occur within GCS reservoirs, which increases the concern for CO2 and brine leakage from the storage reservoir as well as the overlying groundwater contamination. In this work, to investigate the impact of O2 co-injected with CO2 on the geochemical interactions, especially the trace metal mobilization from a GCS reservoir rock, batch studies were conducted with Eau Claire siltstone collected from CO2 sequestration sites. The rock was reacted with synthetic brines in contact with either 100% CO2 or a mixture of 95 mole% CO2-5 mole% O2 at 10.1 MPa and 75 °C. Both microscopic and spectroscopic measurements, including 57Fe-Mössbauer spectroscopy, Laser Ablation-Inductively Coupled Plasma-Mass Spectrometry, powder X-ray diffraction, scanning electron microscopy-energy dispersive x-ray spectroscopy, and chemical extraction were combined in this study to investigate reaction mechanisms. The Eau Claire siltstone contains quartz (52 wt%), fluorapatite (40%), and aluminosilicate (5%) as major components, and dolomite (2%), pyrite (1%), and small-particle-/poorly-crystalline Fe-oxides as minor components. With the introduction of CO2 into the reaction vessel containing rock and brine, the leaching of small amounts of fluorapatite, aluminosilicate, and dolomite occurred. Trace metals of environmental concern, including Pb, As, Cd, and Cu were detected in the leachate with concentrations up to 400 ppb in the CO2-brine-rock reaction system within 30 days. In the presence of O2, the mobilization of Pb, Cd, and Cu was significantly enhanced, whereas As concentrations decreased, compared with the reaction system without oxygen. The presence of oxygen resulted in the formation of secondary Fe-oxides which appear to be Fe(II)-substituted P-containing ferrihydrite. Although the rock contained only 1.04 wt% total Fe, oxidative dissolution of pyrite, leaching and oxidation of structural Fe(II) in fluorapatite, and precipitation of Fe-oxides significantly decreased the pH in brine with oxygen(pH 3.3-3.7), compared with the reaction system without oxygen (pH 4.2-4.4). In the CO2-rock-brine system without O2, the majority of As remained in the rock, with about 1.1% of the total As being released from intrinsic Fe-oxides to the aqueous phase. The release behavior of As to solution was consistent with competitive adsorption between phosphate/fluoride and As on Fe-oxide surfaces. In the presence of O2 the mobility of As was reduced due to enhanced adsorption onto both intrinsic and secondary Fe-oxide surfaces.When O2 was present, the dominant species in solution was the less toxic As(V). This work will advance our understanding of the geochemical reaction mechanisms that occur under GCS conditions and help to evaluate the risks associated with geological CO2 sequestration.

CO2 sequestration, metal release, ground↗

Characterization of damage processes in Montney siltstone under triaxial compression using acoustic emission and diagnostic imaging

SUMMARY Crack nucleation and rock failure processes in a fine-grained siltstone (Montney Formation) under triaxial compression are investigated using combined diagnostic techniques, including ultrasonic-wave measurement, acoustic-emission (AE) monitoring, computed tomography (CT) scanning, and thin-section imaging. The sample displays a weak-to-moderate inherent seismic anisotropy and noticeable stress-induced anisotropy prior to failure. No AE event was detected until the applied axial stress reached 95 per cent of the peak value. The signal-to-noise ratio is relatively low, however, and detectable AE events are more diffuse than those observed in highly brittle rocks. The AE locations correlate with a shear fracture zone imaged by CT scanning. AE moment-tensor analysis reveals that events with larger relative magnitudes are characterized by high volumetric (tensile or compressive) components, and the initiation of the failure zone is dominated by combined shear-tensile (ST) failure. Stress inversion of the AE events with high tensile components is in good agreement with the known applied stress. Microscopic imaging of thin sections from the failed sample shows that the failure zone is an en echelon structure consisting of a major fracture with branching micro and minor cracks. This failure mechanism is consistent with a ST source mechanism and is interpreted to be associated with the fine granular structure and mineral composition of Montney siltstone.

Jia, Suzie Q. (ORCID:0000000326496190)↗

Multiscale Characterization of the Caney Shale — An Emerging Play in Oklahoma

From a hydrocarbon perspective, the Caney Shale has historically been evaluated as a sealing unit, which resulted in limited studies characterizing the rock properties of the Caney Shale and its suitability for hydraulic fracturing. The objective of our research is to help bridge the current knowledge gap through the integration of multiscale laboratory techniques and to characterize the macro- and microscale rock properties of the Caney Shale. We employed an integrated approach for the characterization of the Caney using 200 ft (61 m) of Caney core from a target well in southern Oklahoma. Core observation and petrographic analysis of thin sections were combined to characterize the general rock types and associated fabrics and textures. Mineralogical composition, pore system architecture, and rock fabric were analyzed using x-ray diffraction (XRD), scanning electron microscopy/energy dispersive x-ray spectroscopy (SEM/EDS), and focused ion beam (FIB)-SEM. In addition, rebound hardness and indentation testing were carried out to determine rock hardness (brittleness) and elasticity, respectively. With the integrated multiscale characterization, three mixed carbonate-siliciclastic rock types were identified — mudstone, calcareous siltstone, and silty carbonate — likely representing a spectrum of deposition from low to relatively high energy environments in the distal portions of a ramp system. Silty carbonate contains mostly interparticle pores. The calcareous siltstones and silty mudstones contain a combination of organic matter pores and interparticle pores. Each of the rock types shows unique mineralogical compositions based on XRD. The mudstone lithofacies has the highest clay content and the least carbonate content. Calcareous siltstones show moderate carbonate and clay content. Silty carbonate indicates the highest carbonate content with the least clay content. In an order of mudstone, calcareous siltstone, and silty carbonate, rebound hardness and Young’s modulus show an increasing trend. As a result of rock-fluid interactions, there are potential scaling reactions during completion and production that could ultimately affect permeability and production rates. Overall, the proposed multiscale integration approach is critical for the geologic characterization of most rocks. However, in shale reservoirs dominated by microporosity and microstructure where engineered fractures are expected to provide permeability at a reservoir scale, successful integration is essential. An optimized, integrated geological characterization of the Caney Shale that is well aligned with the engineering designs in drilling, completing, and producing wellbores will ultimately lead to optimal production while providing safe and environmentally responsible operations.

Wang, Yulun↗

Early burial mud diapirism and its impact on stratigraphic architecture in the Carboniferous of the Shannon Basin, County Clare, Ireland

Delta fronts are often characterized by high rates of sediment supply that result in unstable slopes and a wide variety of soft-sediment deformation, including the formation of overpressured and mobile muds that may flow plastically during early burial, potentially forming mud diapirs. The coastal cliffs of County Clare, western Ireland, expose Pennsylvanian (Namurian) delta-front deposits of the Shannon Basin at large scale and in three dimensions. These deposits include decametre-scale, internally chaotic mudstone masses that clearly impact the surrounding sedimentary strata. Evidence indicates that these were true mud (unlithified sediment) diapirs that pierced overlying strata. This study documents a well-exposed ca 20 m tall mud diapir and its impact on the surrounding mouth-bar deposits of the Tullig Cyclothem. A synsedimentary fault and associated rollover dome, evident from stratal thicknesses and the dip of the beds, define one edge of the diapir. These features are interpreted as recording the reactive rise of the mud diapir in response to extensional faulting along its margin. Above the diapir, heterolithic sandstones and siltstones contain evidence for the creation of localized accommodation, suggesting synsedimentary filling, tilting and erosion of a shallow sag basin accommodated by the progressive collapse of the diapir. Two other diapirs are investigated using three-dimensional models built from ‘structure from motion’ drone imagery. Both diapirs are interpreted to have grown predominantly through passive rise (downbuilding). Stratal relationships for all three diapirs indicate that they were uncompacted and fluid-rich mud beds that became mobilized through soft-sediment deformation during early burial (i.e. <50 m, likely <10 m depth). Each diapir locally controlled the stratigraphic architecture in the shallow subsurface and potentially influenced local palaeocurrents on the delta. The mud diapirs studied herein are distinct from deeper ‘shale diapirs’ that have been inferred from seismic sections worldwide, now largely disputed.

defects, mechanical behavior, carbon sequestration↗

Principal sources and dispersal patterns of suspended particulate matter in nearshore surface waters of the northeast Pacific Ocean and the Hawaiian Islands

The author has identified the following significant results. Numerous geologic features can be discerned on ERTS-1 imagery of the northwestern Olympic Peninsula, Washington, and southern Vancouver Island, British Columbia. A thick homoclinal sequence of north-dipping Tertiary marine strata along the northwestern Olympic Peninsula is readily discernible because of the banded nature of its outcrop. The submarine basalt on which the sequence rests shows as a high, rugged ridge. Within the sedimentary sequence, alternating sandstone and siltstone members 100 m or more thick show in the southeast corner of the image. Broad folds in this banded sequence and faults that cut it can be detected. One large fault, the Pysht River fault, and a large syncline in sandstone and siltstone east of it show prominently on the image. Numerous lineations on the image of southern Vancouver Island correlate with faults shown on Muller's map. Particularly prominent are the Leech River and San Juan faults along the southernmost part of the island.

Carlson, P. R.↗

Research core drilling in the Manson impact structure, Iowa

The Manson impact structure (MIS) has a diameter of 35 km and is the largest confirmed impact structure in the United States. The MIS has yielded a Ar-40/Ar-39 age of 65.7 Ma on microcline from its central peak, an age that is indistinguishable from the age of the Cretaceous-Tertiary boundary. In the summer of 1991 the Iowa Geological Survey Bureau and U.S. Geological Survey initiated a research core drilling project on the MIS. The first core was beneath 55 m of glacial drift. The core penetrated a 6-m layered sequence of shale and siltstone and 42 m of Cretaceous shale-dominated sedimentary clast breccia. Below this breccia, the core encountered two crystalline rock clast breccia units. The upper unit is 53 m thick, with a glassy matrix displaying various degrees of devitrification. The upper half of this unit is dominated by the glassy matrix, with shock-deformed mineral grains (especially quartz) the most common clast. The glassy-matrix unit grades downward into the basal unit in the core, a crystalline rock breccia with a sandy matrix, the matrix dominated by igneous and metamorphic rock fragments or disaggregated grains from those rocks. The unit is about 45 m thick, and grains display abundant shock deformation features. Preliminary interpretations suggest that the crystalline rock breccias are the transient crater floor, lifted up with the central peak. The sedimentary clast breccia probably represents a postimpact debris flow from the crater rim, and the uppermost layered unit probably represents a large block associated with the flow. The second core (M-2) was drilled near the center of the crater moat in an area where an early crater model suggested the presence of postimpact lake sediments. The core encountered 39 m of sedimentary clast breccia, similar to that in the M-1 core. Beneath the breccia, 120 m of poorly consolidated, mildly deformed, and sheared siltstone, shale, and sandstone was encountered. The basal unit in the core was another sequence of sedimentary clast breccia. The two sedimentary clast units, like the lithologically similar unit in the M-1 core, probably formed as debris flows from the crater rim. The middle, nonbrecciated interval is probably a large, intact block of Upper Cretaceous strata transported from the crater rim with the debris flow. Alternatively, the sequence may represent the elusive postimpact lake sequence.

Anderson, R. R.↗

Geology and Hydrothermal Alteration of the Raft River Geothermal System, Idaho

The Raft River geothermal system is located in southern Idaho, near the Utah-Idaho state boarder in the Raft River Valley. The field, which is owned and operated by U.S. Geothermal, has been selected as an EGS demonstration site by the U. S. Department of Energy. This paper summarizes ongoing geologic and petrologic investigations being conducted in support of this project. The reservoir is developed in fractured Proterozoic schist and quartzite, and Archean quartz monzonite cut by younger diabase intrusions. The basement complex was deformed during the mid Tertiary and covered by approximately 5000 ft of late Tertiary sedimentary and volcanic deposits. Listric normal faults of Cenozoic age disrupt the Tertiary deposits but do not offset the basement rocks. RRG-9, the target well, was drilled southwest of the main well field to a measured depth (MD) of 6089 ft. The well is deviated to the west and cased to a depth of 2316 ft MD. It penetrated the Proterozoic reservoir rocks at a depth of 5286 ft MD and encountered a maximum temperature of 139 degrees C. Bottomhole temperatures in other deep wells range from 133 to 149 degrees C. X-ray diffraction and thin section analyses are being conducted on samples from 5 deep wells, RRG- 1, 2, 3, 7 and 9, to determine the characteristics of the rock types and hydrothermal alteration within the geothermal system. Thin section analyses of samples from RRG-9 document the presence of strong alteration and brecciation at the contact between the Tertiary and basement complex. The Tertiary rocks consist of ash-flow tuffs, lava flows, tuffaceous siltstone, greywacke, and sandstone. No core is available from RRG-9 but core was obtained from RRG-3C. The sample is a brecciated and altered siltstone from the base of the Tertiary sequence and is similar to rocks at the base of the Tertiary deposits in RRG-9. Here, the results of thermal and quasi-static mechanical property measurements that were conducted on the core sample are presented.

Jones, Clay↗

Characterization of Tight Gas Reservoir Pore Structure Using USANS/SANS and Gas Adsorption Analysis

Small-angle and ultra-small-angle neutron scattering (SANS and USANS) measurements were performed on samples from the Triassic Montney tight gas reservoir in Western Canada in order to determine the applicability of these techniques for characterizing the full pore size spectrum and to gain insight into the nature of the pore structure and its control on permeability. The subject tight gas reservoir consists of a finely laminated siltstone sequence; extensive cementation and moderate clay content are the primary causes of low permeability. SANS/USANS experiments run at ambient pressure and temperature conditions on lithologically-diverse sub-samples of three core plugs demonstrated that a broad pore size distribution could be interpreted from the data. Two interpretation methods were used to evaluate total porosity, pore size distribution and surface area and the results were compared to independent estimates derived from helium porosimetry (connected porosity) and low-pressure N{sub 2} and CO{sub 2} adsorption (accessible surface area and pore size distribution). The pore structure of the three samples as interpreted from SANS/USANS is fairly uniform, with small differences in the small-pore range (< 2000 {angstrom}), possibly related to differences in degree of cementation, and mineralogy, in particular clay content. Total porosity interpreted from USANS/SANS is similar to (but systematically higher than) helium porosities measured on the whole core plug. Both methods were used to estimate the percentage of open porosity expressed here as a ratio of connected porosity, as established from helium adsorption, to the total porosity, as estimated from SANS/USANS techniques. Open porosity appears to control permeability (determined using pressure and pulse-decay techniques), with the highest permeability sample also having the highest percentage of open porosity. Surface area, as calculated from low-pressure N{sub 2} and CO{sub 2} adsorption, is significantly less than surface area estimates from SANS/USANS, which is due in part to limited accessibility of the gases to all pores. The similarity between N{sub 2} and CO{sub 2}-accessible surface area suggests an absence of microporosity in these samples, which is in agreement with SANS analysis. A core gamma ray profile run on the same core from which the core plug samples were taken correlates to profile permeability measurements run on the slabbed core. This correlation is related to clay content, which possibly controls the percentage of open porosity. Continued study of these effects will prove useful in log-core calibration efforts for tight gas.

03 NATURAL GAS↗

Annual report of monitoring at Barnes, Kansas, in 2011

Barnes, Kansas, is a small rural community (population approximately 150) located in Washington County, in north-central Kansas (Figure 1.1). The city lies in a transition zone between the Flint Hills and the glaciated region. The area's topography consists of gently sloping hills of Pleistocene loess (< 20 ft) overlying a shale unit and interbedded shale, limestone, and siltstone of the Permian Chase Group.

54 ENVIRONMENTAL SCIENCES↗

Discrete element modeling of indentation tests to investigate mechanisms of CO 2 -related chemomechanical rock alteration

During CO 2 injection into geological formations, petrophysical and geomechanical properties of host formations can be altered due to mineral dissolution and precipitation. Field and laboratory results have shown that sandstone and siltstone can be altered by CO 2 -water mixtures, but few quantitative studies have been performed to fully investigate underlying mechanisms. Based on the hypothesis that CO 2 -water mixtures alter the integrity of rock structure by attacking cements rather than grains, we attempt to explain the degradation of cementation due to long-term contact with CO 2 and water and mechanisms for changes in rock mechanical properties. Many sandstones, including calcite-cemented quartzitic sandstone, chlorite-cemented quartzitic sandstone, and hematite-cemented quartzitic sandstone, contain interparticle cements that are more readily affected by CO 2 -water mixtures than grains. A model that couples the discrete element method and the bonded-particle model is used to perform simulations of indentation tests on synthetic rocks with crystal and random packings. The model is verified against the analytical cavity expansion model and validated against laboratory indentation tests on Entrada sandstone with and without CO 2 alteration. Sensitivity analysis is performed for cementation microscopic parameters including stiffness, size, axial, and shear strength. The simulation results indicate that the CO 2 -related degradation of mechanical properties in bleached Entrada sandstone can be attributed to the reduction of cement size rather than cement strength. Finally, our study indicates that it is possible to describe the CO 2 -related rock alteration through particle-scale mechanisms.

54 ENVIRONMENTAL SCIENCES↗

CO 2 -induced chemo-mechanical alteration in reservoir rocks assessed via batch reaction experiments and scratch testing

Here, the injection of carbon dioxide (CO 2 ) into geological formations results in a chemical re-equilibration between the mineral assemblage and the pore fluid, with ensuing mineral dissolution and re-precipitation. Hence, target rock formations may exhibit changes of mechanical and petrophysical properties due to CO 2 exposure. We conducted batch reaction experiments with Entrada Sandstone and Summerville Siltstone exposed to de-ionized water and synthetic brine under reservoir pressure (9–10 MPa) and temperature (80°C) for up to four weeks. Samples originate from the Crystal Geyser field site, where a naturally occurring CO 2 seepage alters portions of these geologic formations. We conducted micro-scratch tests on rock samples without alteration, altered under laboratory conditions, and naturally altered over geologic time. Scratch toughness and hardness decrease as a function of exposure time and water salinity up to 52% in the case of Entrada and 87% in the case of Summerville after CO 2 -induced alteration in the laboratory. Imaging of altered cores with SEM-EDS and X-ray microCT methods show dissolution of carbonate and silica cements and matrix accompanied by minor dissolution of Fe-oxides, clays, and other silicates. Parallel experiments using powdered samples confirm that dissolution of carbonate and silica are the primary reactions. The batch reaction experiments in the autoclave utilize a high fluid to rock volume ratio and represent an end member of possible alteration associated with CO 2 storage systems. These types of tests serve as a pre-screening tool to identify the susceptibility of rock facies to CO 2 -related chemical-mechanical alteration during long-term CO 2 storage.

54 ENVIRONMENTAL SCIENCES↗

Evaluation of experimentally measured and model-calculated pH for rock-brine-CO2 systems under geologic CO2 sequestration conditions

pH is an essential parameter for understanding the geochemical reactions that occur in rock-brine-CO2 systems when CO2 is injected into deep geologic formations for long-term storage. Due to a lack of reliable experimental methods, most laboratory studies conducted under geological CO2 sequestration (GCS) conditions have relied on thermodynamic modeling to estimate pH. The accuracy of these model predictions is typically uncertain. In our previous work, we have developed a method for pH determination by in-situ spectrophotometry. In the present work, we expanded the applicable pH range for this method and measured the pH of several rock-brine-CO2 systems at GCS conditions for five rock samples collected from ongoing GCS demonstration projects. Experimental measurements were compared with pH values calculated using several geochemical modeling approaches. The effect of different thermodynamic databases on the accuracy of model prediction was evaluated. Results indicate that the accuracy of model calculations is rock-dependent. For rocks comprised of carbonate and sandstone, model results generally agreed well with experimentally measured pH; however, for basalt, significant differences were observed. These discrepancies may be due to the models’ failure to fully account for certain reaction occurring between the basalt minerals the CO2-saturated brine solutions.

pH, carbon sequestration↗

Stratigraphic control of landscape response to base-level fall, Young Womans Creek, Pennsylvania, USA [Caprock controls on landscape response to baselevel fall constrained by nested detrital in situ 10Be, Young Womans Creek, Pennsylvania, USA]

Landscapes are thought to respond to changes in relative base level through the upstream propagation of a boundary that delineates relict from adjusting topography. However, spatially-variable rock strength can influence the topographic expression of such transient landscapes, especially in layered rocks, where strength variations can mask topographic signals expected due to changes in climate or tectonics. Here, we analyze the landscape response to base-level fall in Young Womans Creek, a 220 km 2 catchment on the Appalachian Plateau, USA underlain by gently folded Paleozoic sedimentary rocks. We measured in situ 10 Be concentrations in stream sands from 17 nested watersheds, and used a spatially-distributed model of sediment and 10 Be production to constrain a threefold increase in the rate of base-level fall propagating upstream from the catchment outlet. Using lidar topography and a nearby detailed stratigraphic section, we map the extent of continuous, blocky, resistant sandstone strata that act as a caprock overlying more easily erodible sandstones and siltstones. The caprock influences landscape response in two ways. First, it serves as a boundary between slowly eroding (11.5 m Myr –1 ), low-sloping (3–5°) areas of relict topography and lower, steeper portions of the landscape adjusting to base-level fall. Second, hillslopes supported by the overlying caprock are armored with coarse sediment and are significantly steeper (20–30°) than hillslopes where the caprock has been eroded (10°), despite having similar erosion rates (36 m Myr –1 ) and bedrock substrate. Lastly, our results illustrate how gently dipping, layered rocks engender complicated relationships between lithology, topography and erosion rate, highlighting the importance of understanding how rock material properties influence surface processes and landscape evolution.

58 GEOSCIENCES↗

Permeability and Induced Polarization of Mudstones

Electrical measurements can be used to estimate hydraulic properties such as permeability ( k ) in sedimentary rocks. Previous work has focused on sandstones, siltstones, and carbonates, while investigations on mudstones have rarely been reported. In this study, we report on electrical geophysical measurements for 23 mudstone samples using an experimental approach designed to reliably saturate these low permeability mudstones. The modified Hagen-Poiseuille model linking permeability to the formation factor ( F ) and an effective pore radius ( r ) provides an excellent fit to the data set with a near-constant pore radius, indicating that the effective porosity (1/ F ) is the controlling factor on k . In these samples, the surface area normalized to pore volume ( S por ), frequently used in permeability estimation models, varies by 1–2 orders of magnitude and is thus not a reliable proxy of the inverse effective hydraulic radius. The formation factor also exerts the primary control on induced polarization (IP) parameters, whereas Spor shows no relation to the IP parameters. A strong linear relationship is found between IP parameters (imaginary conductivity and normalized chargeability) and surface conductivity, although the proportionality factor is significantly lower than those observed in more permeable rocks and sediments. Apparent relationships between the polarization strength-derived and time constant-derived geophysical length scales and the effective hydraulic radius appear to be driven by variations in the electrochemical parameters (i.e., specific polarizability and diffusion coefficient). Overall, these findings emphasize that predicting hydraulic properties from electrical measurements in fine-grained rocks remains challenging and requires further investigation into the electrochemical properties involved.

58 GEOSCIENCES↗

Preservation of erniettomorph fossils in clay-rich siliciclastic deposits from the Ediacaran Wood Canyon Formation, Nevada

Three-dimensionally preserved Ediacaran fossils occur globally within sandstone beds. Sandy siliciclastic deposits of the Ediacaran Wood Canyon Formation (WCF) in the Montgomery Mountains, Nevada, contain two fossil morphologies with similar shapes and sizes: one exhibits mm-scale ridges and a distinct lower boundary and the other is devoid of these diagnostic features. We interpret these as taphomorphs of erniettomorphs, soft-bodied organisms with uncertain taxonomic affinities. We explore the cast-and-mould preservation of both taphomorphs by petrography, Raman spectroscopy, X-ray fluorescence microprobe and X-ray diffraction. All fossils and the surrounding sedimentary matrix contain quartz grains, iron-rich chlorite and muscovite. The ridged fossils contain about 70% larger quartz grains compared to the ridgeless taphomorph, indicating a lower abundance of clay minerals in the ridged fossil. Chlorite and muscovite likely originated from smectite and kaolinite precursors that underwent lower greenschist facies metamorphism. Kaolinite and smectite are inferred to have been abundant in sediments around the ridged fossil, which enabled the preservation of a continuous, distinct, clay- and kerogen-rich bottom boundary. The prevalence of quartz in the ridged fossils of the WCF and in erniettomorphs from other localities also suggests a role for this mineral in three-dimensional preservation of erniettomorphs in sandstone and siltstone deposits.

58 GEOSCIENCES↗

3D Model of the Tuscarora Geothermal Area

The Tuscarora geothermal system sits within a ~15 km wide left-step in a major west-dipping range-bounding normal fault system. The step over is defined by the Independence Mountains fault zone and the Bull Runs Mountains fault zone which overlap along strike. Strain is transferred between these major fault segments via and array of northerly striking normal faults with offsets of 10s to 100s of meters and strike lengths of less than 5 km. These faults within the step over are one to two orders of magnitude smaller than the range-bounding fault zones between which they reside. Faults within the broad step define an anticlinal accommodation zone wherein east-dipping faults mainly occupy western half of the accommodation zone and west-dipping faults lie in the eastern half of the accommodation zone. The 3D model of Tuscarora encompasses 70 small-offset normal faults that define the accommodation zone and a portion of the Independence Mountains fault zone, which dips beneath the geothermal field. The geothermal system resides in the axial part of the accommodation, straddling the two fault dip domains. The Tuscarora 3D geologic model consists of 10 stratigraphic units. Unconsolidated Quaternary alluvium has eroded down into bedrock units, the youngest and stratigraphically highest bedrock units are middle Miocene rhyolite and dacite flows regionally correlated with the Jarbidge Rhyolite and modeled with uniform cumulative thickness of ~350 m. Underlying these lava flows are Eocene volcanic rocks of the Big Cottonwood Canyon caldera. These units are modeled as intracaldera deposits, including domes, flows, and thick ash deposits that change in thickness and locally pinch out. The Paleozoic basement of consists metasedimenary and metavolcanic rocks, dominated by argillite, siltstone, limestone, quartzite, and metabasalt of the Schoonover and Snow Canyon Formations. Paleozoic formations are lumped in a single basement unit in the model. Fault blocks in the eastern portion of the model are tilted 5-30 degrees toward the Independence Mountains fault zone. Fault blocks in the western portion of the model are tilted toward steeply east-dipping normal faults. These opposing fault block dips define a shallow extensional anticline. Geothermal production is from 4 closely-spaced wells, that exploit a west-dipping, NNE-striking fault zone near the axial part of the accommodation zone.

15 GEOTHERMAL ENERGY↗

AmeriFlux US-CLF Cole Farm

This is the AmeriFlux version of the carbon flux data for the site US-CLF Cole Farm. Site Description - The Cole Farm catchment (0.65km2) is located ~ 4 km southwest of the Shale Hills site, draining orthogonally to a syncline axis of the Wills Creek Formation, a calcareous shale containing interbedded siltstone, sandstone, shaly limestone, and dolomite. Even though the farm adopted no-till practices in the 1970s, the axial channel of Cole Farm flows over a thick (>2.5 m) package of sediment in the valley floor. Soils range in texture from silty clay at the ridge top to sandy loam in the valley floor. Data was collected and funded by the Critical Zone Observatory Network.

Davis, Kenneth J.↗