Preparation of samples for sintering of submicron particles by transmission electron microscopy
Monolayer submicron self supporting particle film samples preparation for sintering by transmission electron microscopy
Sipe, J. J.↗
SEARCH · Search NASA
Results for “sintering preparation”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Pulsed Laser Deposition of BaCe(sub 0.85)Y(sub 0.15)0(sub 3) FILMS
Pulsed laser deposition has been used to grow nanostructured BaCe(sub 0.85)Y(sub 0.15)0(sub 3) films. The objective is to enhance protonic conduction by reduction of membrane thickness. Sintered samples and laser targets were prepared by sintering BaCe(sub 0.85)Y(sub 0.15)O(sub 3) powders derived by solid state synthesis. Films 2 to 6 m thick were deposited by KrF excimer laser on Si and porous Al2O3 substrates. Nanocrystalline films were fabricated at deposition temperatures of 600-800 C deg at O2 pressure of 30 mTorr and laser fluence of 1.2 J/cm square. Films were characterized by x-ray diffraction, scanning electron microscopy and electrical impedance spectroscopy. Dense single phase BaCe(sub 0.85)Y((sub 0.15) 0(sub 3) films with a columnar growth morphology is observed, preferred crystal growth was found to be dependent upon deposition temperature and substrate type. Electrical conductivity of bulk samples produced by solid state sintering and thin film samples were measured over a temperature range of 100 C deg to 900 C deg in moist argon. Electrical conduction of the fabricated films was 1 to 4 orders of magnitude lower than the sintered bulk samples. With respect to the film growth direction, activation energy for electrical conduction is 3 times higher in the perpendicular direction than the parallel direction.
Dynys, F. W.↗
Pulsed Laser Deposition of High Temperature Protonic Films
Pulsed laser deposition has been used to fabricate nanostructured BaCe(0.85)Y(0.15)O3- sigma) films. Protonic conduction of fabricated BaCe(0.85)Y(0.15)O(3-sigma) films was compared to sintered BaCe(0.85)Y(0.15)O(3-sigma). Sintered samples and laser targets were prepared by sintering BaCe(0.85)Y(0.15)O(3-sigma) powders derived by solid state synthesis. Films 1 to 8 micron thick were deposited by KrF excimer laser on porous Al2O3 substrates. Thin films were fabricated at deposition temperatures of 700 to 950 C at O2 pressures up to 200 mTorr using laser pulse energies of 0.45 - 0.95 J. Fabricated films were characterized by X-ray diffraction, electron microscopy and electrical impedance spectroscopy. Single phase BaCe(0.85)Y(0.15)O(3-sigma) films with a columnar growth morphology are observed with preferred crystal growth along the [100] or [001] direction. Results indicate [100] growth dependence upon laser pulse energy. Electrical conductivity of bulk samples produced by solid state sintering and thin film samples were measured over a temperature range of 100 C to 900 C. Electrical conduction behavior was dependent upon film deposition temperature. Maximum conductivity occurs at deposition temperature of 900 oC; the electrical conductivity exceeds the sintered specimen. All other deposited films exhibit a lower electrical conductivity than the sintered specimen. Activation energy for electrical conduction showed dependence upon deposition temperature, it varied
Dynys, Fred W.↗
Characteristics of Si3N4-SiO2-Ce2O3 compositions sintered in high-pressure nitrogen
Full-density Si3N4-SiO2-Ce2O3 compositions were prepared by sintering with 2.5 MPa nitrogen pressure at temperatures of 1900 and 2090 C. Room-temperature flexural strengths near 700 MPa for sintered material compared favorably with the strength of hot-pressed material. At 1370 C, where flexural strengths as high as 363 MPa were obtained, it was observed that the coarsest structure was the strongest and the finest structure was the weakest. One of the compositions tested, Si3N4-8.7 wt pct SiO2-8.3 wt pct-Ce2O3, was found to have excellent 200-h oxidation resistance at 700, 1000, and 1370 C, without incidence of 700 to 1000 C phase instability and cracking.
Sanders, W. A.↗
Fabrication Of Metal Chloride Cathodes By Sintering
Transition-metal chloride cathodes for use in high-temperature rechargeable sodium batteries prepared by sintering transition-metal powders mixed with sodium chloride. Need for difficult and dangerous chlorination process eliminated. Proportions of transition metal and sodium chloride in mixture adjusted to suit specific requirements. Cathodes integral to sodium/metal-chloride batteries, which have advantages over sodium/sulfur batteries including energy densities, increased safety, reduced material and thermal-management problems, and ease of operation and assembly. Being evaluated for supplying electrical power during peak demand and electric vehicles.
Bugga, Ratnakumar V.↗
Production of uniform nickel-cadmium battery plate materials Quarterly report, 13 Sep. - 12 Dec. 1969
Preparation of sintered nickel plaques under varied experimental conditions for development of laboratory process to manufacture uniform and reliable nickel cadmium battery plate materials
Source record↗
On Heat-Treatable Copper-Chromium Alloy, 1
A mother alloy of 10% Cr and 90% Cu was prepared by sintering. This was alloyed with the Cu melt and Cu-Cr alloys containing about 0.5% Cr was obtained. These alloys could be deformed easily in both the hot and cold states. By measuring the hardness change, age-hardening properties of cast alloys were studied, which were quenched from 950 deg and aged at 300 to 700 deg for 1 hour. The maximum hardness was obtained with the tempering temperature of 500 deg. For the temperature of solution-treatment, 950 deg was insufficient and that above 1000 deg necessary. For the tempering time, a treatment at 500 deg for 1 hr. or at 450 deg for 3 hrs. yielded the maximum hardness. As for the properties for electrical conductors, 3 kinds of wires (diam. 2 mm.) were made: (1) after cold-drawn to 2 mm., solution-treated, quenched, and then tempered (500 deg, 1 hr.); (2) after quenching, cold-drawn (75% reduction) to 2 mm. and tempered (500 deg, 1 hr.); and (3) after quenching, cold-drawn (81%) to intermediate diameter, tempered (500 deg, 1 hr.) and then cold-drawn (88%) again. Properties obtained for the 3 kinds, respectively, were as follows: conductivity 91, 90, and 86%. Tensile strength and strength for electrical conductivity are given.
Koda, S.↗
Model studies in catalysis with uhv-deposited metal particles and clusters
Small supported metal particles have become a popular area of intense research interest, and important contributions to the considered problems are being made from the fields of uhv technology, thin film physics surface science, and surface and thin film instrumentation. Attention is given to insulating supports, particulate metal deposits and their properties, metal/support interactions and gas exposures, and integrated experimental approaches. It is concluded that major contributions to the field of model catalysis should be forthcoming in the near future from uhv-based methods of research. Catalysis and catalysis-related problem areas expected to benefit from advanced model studies include catalyst preparation processing, sintering mechanisms for metals and alloys, separation of initial and final state effects for supported clusters, and the influence of particle and/or support morphologies.
Poppa, H.↗
A high-temperature heat sensitive element
This invention concerns the high-temperature heat sensitive element which is stable at high temperatures. A solid solution of the main component MgO-Al2O3-Cr2O3-Fe2O3 which contains spinel crystal structure is mixed with the secondary component ZrO2 at the mol ratio of 100 : 0.1 to 5.0 and sintered to prepare a high-temperature heat sensitive element.
Oguro, M.↗
Grinding Si3N4 Powder In Si3N4 Equipment
Three methods of grinding compared. Report based on study of grinding silicon nitride powder in preparation for sintering into solid ceramic material. Attrition, vibratory, and ball mills lined with reaction-bonded silicon nitride tested. Rates of reduction of particle sizes and changes in chemical compositions of powders measured so grinding efficiences and increases in impurity contents from wear of mills and media evaluated for each technique.
Herbell, Thomas P.↗
Development of electrostrictive ceramic motor actuators
Electrostriction, which exists in all materials, exhibits many potential applications in electronic and optically controlled systems. Few materials, however, possess electrostrictive effects large enough to be of practical usefulness. The development of materials with high electrostrictive coefficients has been a major impetus of much research in this area. The Pb(x)Ba(1 - x)(Zr(y)Ti(1 - y))O3 (PBZT) ceramic system appears to be a very promising candidate because of the electrostrictive coefficients, Q(sub 11) and Q(sub 12), are among the highest discovered today. In this paper, we describe the preparation and sintering of the PBZT(73/37) ceramic, and the effect of some sintering conditions on sintered samples. The results on the measurement of the electrostrictive and related properties are presented. In addition, a brief discussion of characteristics of PBZT ceramics is provided.
Gene H. Haertling↗
Effect of Processing on Morphology of Hydroxyapatites: Bioactive Glasses and Crystalline Composites
Recent studies on multinary oxides for applications as laser hosts and high dielectric capacitors have shown that processing at high temperature provides glassy or crystalline materials based on thermal treatments and cooling rates. Since hydroxyapatites are now subject of great interests due to their bioactivity, interest in producing soft and hard materials with glassy and crystalline nature by processing parameters has become very important. Crystalline materials by using Bridgman, Czochralski and flux growth methods are costly and require huge investment. We have observed that even low temperature solidification in organic flux produced oriented fibers. This organic treated material has different characteristics than in situ oxide materials prepared by sintering and grain growth. Examples of phosphate and silicate-based systems will be presented to demonstrate soft and hard materials. Effect of TiO2 and other hardening elements will be also reported.
McAdams, Joel↗
TEM observations on grain boundaries in sintered silicon, part 1
Grain boundaries in silicon with a predetermined orientation were prepared by the sintering of two single crystals. A combination of standard transmission electron microscopy and lattice imaging was used to investigate the structure of the boundaries produced. Low angle grain boundaries on (100) and (111) planes, and twin boundaries on (111) planes are discussed in detail.
Ast, D. G.↗
Microwave Sintering Lunar Landing Pads & Horizontal Infrastructure
Moon to Mars Planetary Autonomous Construction Technology’s (MMPACT) Microwave Structure Construction Capability (MSCC) team is developing the ability to prepare the lunar regolith and densify it into glass-ceramic landing pads and horizontal infrastructure. Microwave energy will be utilized to densify the lunar regolith. Some of the concept of operations, simulant and synthetic minerals, site preparation, design, microwave sintering, testing, & ancillary instrument technical challenges were listed. A current status of the MSCC project is also provided.
Microwave, sintering, lunar, regolith, landing pad↗
Ammonia formation caused by the presence of water in the wet grinding of silicon nitride powder
Si3 N4 powder (amorphous, alpha-, and beta-Si3 N4) was mixed with MeOH containing 8.87 mol. % H2O and ground. The NH3 generation rapidly increased after a grinding time of 100 hours. Silicon nitride sintered material was chosen as one of the high temperature, high strength structural materials and studies of the control of the raw material powder, preparation of the sintered body (finding the right assistant, hot press, high pressure sintering, fracture toughness and oxidation at high temperature were performed.
Kanno, Y.↗
Improved plaque materials for aerospace nickel-cadmium cells
Improved cadmium electrode substrates with precisely controlled microstructures for possible use in aerospace nickel-cadmium cells were prepared. The preparative technique was a powder metallurgical process in which a fugitive pore-former and a nickel powder were blended, then isostatically compacted, and subsequently sintered. Cadmium electrodes prepared from such substrates were cycle tested using an accelerated tortuous test regime. It was discovered that plaques of 60% or 80% porosity prepared with a 25 micron pore-former were better than state-of-the-art electrodes in terms of efficienty and/or mechanical strength. The 60% structures were particularly outstanding in this respect in that they had efficiencies only 5-10 percentage points lower than state-of-the-art electrodes and vastly superior mechanical properties. This added strength was observed to eliminate cracking and physical degradation of the electrodes during processing and cycling. The cadmium electrodes prepared from the 80% porous substrates proved to be the best electrodes made during the course of the work from the point of view of highest efficiency. Three-point bend tests were used to measure mechanical properties of the plaques produced and also as a general characterization tool. In addition, the BET surface areas of selected specimens was determined. The SEM was used for judging microscopic uniformity and quantitatively determining the induced pore size and various other fine structures in the substrates. The technique of X-ray radiography was used to follow the bulk uniformity of the substrates at various stages of their processing.
Luksha, E.↗
Heat-sterilized silver oxide-zinc cells: Cycle life studies
A JPL study was conducted to evaluate the cell design parameters that contribute to the cycle life of sealed, heat-sterilized silver oxide-zinc cells. Test cells having a rated capacity of 4.2 A-h were fabricated using zinc oxide electrodes prepared by the sintered Teflon process. Two separator variations were evaluated, one having acrylic acid and the other methacrylic acid grafted to irradiated polyethylene film. Significant results of this study include the following: (1) cycle life in excess of 300 cycles was attained; (2) a zinc oxide/silver stoichiometric ratio of 1.5 resulted in greater cycle life than a ratio of 1.1, and similar cycle life to cells having a ratio of 2; (3) cells having methacrylic acid grafted separators suffered somewhat less in capacity loss due to zinc electrode shape change than cells having acrylic acid type; (4) use of acrylic acid grafted separators was slightly superior to the methacrylic acid type in respect to silver penetration; and (5) the inclusion of a layer of potassium titanate paper adjacent to the zinc electrodes resulted in cells that achieved higher cycle life before any of the group failed than that reached by cells of any other construction.
Arms, J. T.↗