Search NASA⌕ Search

SEARCH · Search NASA

Results for “sintering temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Moderate temperature sintering of BaZr 0.8 Y 0.2 O 3-δ protonic ceramics by A novel cold sintering pretreatment

The state-of-the-art protonic ceramic conductor BaZr 0.8 Y 0.2 O 3-δ (BZY20) requires an extremely high sintering temperature (≥1700 °C) to achieve the desired relative density and microstructure necessary to function as a proton conducting electrolyte. In this work, we developed a cold sintering pretreatment assisted moderate-temperature sintering method for the fabrication of high-quality pure BZY20 pellets. BZY20 pellets with high relative density of ~94% were fabricated with a final sintering temperature of 1500 °C (200 °C lower than the traditional sintering temperature). A comparison with BZY20 control samples indicated that the proper amount of BaCO 3 introduced on the BZY20 particle surface and the high green density achieved by cold sintering pretreatment were the main drivers for lowering the sintering temperature. The electrical conductivity measurement by electrochemical impedance spectroscopy showed that the as-prepared BZY20 pellets have a proton conductivity comparable to the state-of-the-art values. The cold sintering pretreatment outlined in this work has the potential to lower the sintering temperatures for similar types of protonic ceramic materials under consideration for a wide range of energy conversion and storage applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Enhancing low-temperature sintering in the MgO-LiF system: Mechanistic insights

In the present article, we provide compelling evidence that minor (1 wt%) additions of micron and nanometre-sized LiF particles in MgO decompose leading to free Li diffusing into MgO surfaces enhancing vacancy production during direct current sintering. The addition of nanometre-sized LiF particles leads to a > 500 °C reduction in the sintering temperature and over 99 % theoretical density of final consolidated compacts. Correlating differential scanning calorimetry with in-situ x-ray diffraction, together with Schottky calculations, post sintering electron microscopy and laser induced breakdown spectroscopy, we uncover critical insights into this impressive reduction in sintering temperature. Our quantitative analysis reveals that MgO and LiF interact at low temperatures with the diffusion of Li into the surface of MgO particles due to the intrinsic structural disorder of the LiF and MgO crystallites. Nanometre-sized LiF particles were found to react the most at low temperatures due to their increased structural disorder. Our multimodal characterization points to a Li-promoted densification and sintering mechanism. This impressive reduction in sintering temperature can be harnessed to promote low-temperature fabrication of MgO-based composites for technological applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effect of sintering temperature on feature resolution and flexural strength of ceramics fabricated through vat photopolymerization additive manufacturing

Although ceramic additive manufacturing (AM) could be used to fabricate complex, high-resolution parts for diverse, functional applications, one ongoing challenge is optimizing the post-process, particularly sintering, conditions to consistently produce geometrically accurate and mechanically robust parts. This study aims to investigate how sintering temperature affects feature resolution and flexural properties of silica-based parts formed by vat photopolymerization (VPP) AM. Test artifacts were designed to evaluate features of different sizes, shapes and orientations, and three-point bend specimens printed in multiple orientations were used to evaluate mechanical properties. Sintering temperatures were varied between 1000°C and 1300°C. Deviations from designed dimensions often increased with higher sintering temperatures and/or larger features. Higher sintering temperatures yielded parts with higher strength and lower strain at break. Many features exhibited defects, often dependent on geometry and sintering temperature, highlighting the need for further analysis of debinding and sintering parameters. To the best of the authors’ knowledge, this is the first time test artifacts have been designed for ceramic VPP. This work also offers insights into the effect of sintering temperature and print orientation on flexural properties. These results provide design guidelines for a particular material, while the methodology outlined for assessing feature resolution and flexural strength is broadly applicable to other ceramics, enabling more predictable part performance when considering the future design and manufacture of complex ceramic parts.

36 MATERIALS SCIENCE↗
DOE OSTI2023

On the confluence of ultrafast high-temperature sintering and flash sintering phenomena

Ultrafast high-temperature sintering (UHS) and flash sintering are novel methods for rapid sintering of ceramics, often completed in just a few seconds. Here, we show that both also share two additional features: an abrupt rise in electrical conductivity, which is electronic, and electroluminescence. More fundamentally, both are related to phonon physics where MD calculations have shown that proliferation of phonons at the edge of the Brillouin zone can induce Frenkel pairs without the application of electrical fields. Here, we show that, indeed, heating without the application of electric field, can also induce flash: Rapid heating processes of thin films of an oxide-salt deposited on silk fibers, with a propane torch, are shown to induce electronic conductivity, electroluminescence, and rapid sintering of the oxide. Further, the discussion in this article harkens back to two inventions, more than a century ago, which can now be related to flash and UHS: (i) the Nernst glow lamp circa 1900, made from zirconia, and (ii) the Welsbach mantle, constituted from ceria doped thorium oxide, in the late nineteenth century. Thus, the confluence between high heating rate and electric field induced flash phenomena links the past to the new. The emerging question is how injection of phonons that has been shown to create Frenkels can further induce high electronic conductivity and electroluminescence in oxides. Both electronic conductivity and luminescence are likely related to the generation of electron–hole pairs.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Exploring the relationship between solvent-assisted ball milling, particle size, and sintering temperature in garnet-type solid electrolytes

Garnet-type solid electrolytes, such as Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 (LLZTO), are promising materials for solid-state batteries, but processing remains a challenge, in part due to the high sintering temperature required for densification. Additionally, this temperature can be lowered by decreasing the initial particle size via solvent-assisted ball milling, but the relationship between solvent choice, particle properties, sintering behavior, and ionic conductivity is not well understood. In this work, we systematically explore these parameters, showing that milling in commonly used protic solvents, such as alcohols, effectively decreases the particle size but results in lithium loss (through Li + /H + exchange) that leads to poor sintering. By contrast, milling in aprotic solvents with surfactant reduces the particle size to ~220 nm without lithium loss, enabling the fabrication of dense samples (5.1 g/cm 3 ) with good ionic conductivity (0.43 mS/cm at 25 °C) at a lower sintering temperature (1000 °C). We compare ionic conductivities and activation energies for samples prepared with different particle sizes and sintering temperatures and use multiphase-field simulations to identify the mass transport and microstructural mechanisms responsible for the observed sintering dependence on particle size. These results further clarify the relationship between processing parameters and performance and represent important progress toward overcoming fabrication challenges for these materials.

25 ENERGY STORAGE↗
DOE OSTI2025

Effect of sintering temperature on adhesion of spray-on piezoelectric transducers

Conventionally sol-gel spray-on transducers require a high-temperature (> 700 ◦C) sintering process; however, this process can affect the microstructure of the substrate material. For mechanical elbows and valves utilized for fluid transport in the energy sector, the components are designed to have a specific microstructure, and deviations from these specifications can create weak points in the system. For this reason it is important to investigate how the temperature of the deposition process affects the substrate. This paper investigates the effect of high-temperature and low-temperature (< 150 ◦C) processing conditions on the surface composition of the substrate. Furthermore, the resultant transducers from high- and low-temperature fabrication processes are compared to determine if a low-temperature processing method is feasible. For these studies a sol-gel spray-on process is employed to deposit piezoelectric ceramics onto a stainless-steel 316L substrate. Energy-dispersive X-ray spectroscopy is utilized to determine the composition of the substrate surface before and after transducer deposition. Results indicate that the high-temperature processing conditions may alter the surface composition of the metal due to a diffusion of the metal into the ceramic, which results in a metal surface that is bonded to the ceramic. Furthermore, it is shown that low-temperature processing of spray-on transducers is a viable method for transducer fabrication where the resultant transducers meet the industry minimum requirement of 30 dB signalto-noise ratio. In parallel simulation calculations, finite-element method (FEM) studies were performed to model the adhesive strength of the low-temperature processed transducer to the substrate surface. Comparisons between the simulations and experiments suggest that the bond strength is much greater than the commercial gel bonds and closer to hardened epoxy glue bonds. These results indicate that spray-on transducers fabricated under lowtemperature processing conditions are a viable solution for leave-in-place monitoring of structures.

M. Sinding, Kyle↗
DOE OSTI2023

Design, Fabrication, and Screening of Environmental‐Thermal Barrier Coatings Prepared by Ultrafast High‐Temperature Sintering

Abstract The demand for more efficient gas turbines relies heavily on the development of new environmental‐thermal barrier coatings (ETBCs). However, there is still uncertainty about which alloys and composites will be used for the next generation of turbine blades, as well as the most promising coating materials. Herein, an ETBCs development strategy is presented by integrating the coating design, synthesis, and screening using an ultrafast high temperature sintering (UHS) technique to accelerate coating improvements. The initial basis for composition selection is their thermal expansion mismatch with the substrate alloys; for which a temperature‐dependent coefficient of thermal expansion database is created. By combining tape casting method with the UHS technique a high‐throughput synthesis of single and multi‐layer coatings are realized with different compositions, layer stacking sequences, and layer thicknesses. To evaluate the coatings, thermal cycling tests from room temperature to 1300 °C are conducted. The approach enabled coatings on objects with complex geometries, multi‐layer ETBCs, and porosity tailoring by using staged UHS that runs with different temperatures and durations. The fast iteration strategy is more cost‐effective for the screening of ETBCs compared to conventional methods and greater throughput which can be further extended for rapid optimization of other materials systems.

Xie, Hua↗
DOE OSTI2021

All solid thick oxide cathodes based on low temperature sintering for high energy solid batteries

Solid-state batteries (SSBs) could significantly improve the safety and energy density over conventional liquid cells. One key enabling technology is the use of solid electrolytes. NASICON-type Li 1.3 Al 0.3 Ti 1.7 (PO 4 ) 3 (LATP) is a very attractive solid-state electrolyte for the cathode side due to its high oxidation potential and high ionic conductivity. The usage, however, is limited by its large interfacial resistance against most of the cathode materials as well as the thermodynamic instability during high temperature sintering needed to achieve high mass density. Here we construct thin, percolative, and mixed conductive interphases through in situ low-melting-point liquid sintering. These mixed conductive interphases drastically improve the kinetics, leading to high-loading solid LATP/LiCoO 2 cathodes achieving capacity loading of up to ~6 mA h cm –2 . The technique is also applicable to Ni-rich cathode materials, achieving up to ~10 mAh cm –2 , which can lead to more than 400 W h kg –1 cells in SSBs. Furthermore, our composite cathodes show a ten-times and three-times area capacity improvement over the state-of-the-art cathodes using oxide and sulfide SSEs, respectively.

25 ENERGY STORAGE↗
DOE OSTI2023

Reduced-temperature sintering of spinel-type coatings and layers with metallic alloy powder precursors

A method of forming a spinel coating on a substrate is disclosed including the steps of coating at least a portion of the substrate with a precursor including an alloy powder, and sintering the precursor at a temperature of less than 1000 degrees Celsius to form the spinel coating. The alloy powder used for the precursor can include particles having a particle size of less than 10 micrometers. The method can be utilized to form spinel coatings as contact surfaces between electrodes and interconnects of solid oxide fuel cell (SOFC) stacks.

Zhu, Jiahong↗
DOE OSTI2024

Tuning the spontaneous exchange bias effect in La 1.5 Sr 0.5 CoMnO 6 with sintering temperature

Here, in this study, we present a study of the influence of microstructure on the magnetic properties of polycrystalline samples of the La 1.5 Sr 0.5 CoMnO 6 double perovskite, with primary attention to the spontaneous exchange bias effect, a fascinating recently discovered phenomena for which some materials exhibit unidirectional magnetic anisotropy after being cooled in zero magnetic fields. By sintering La 1.5 Sr 0.5 CoMnO 6 at different temperatures, we obtained samples with distinct average grain sizes, ranging from 1.54-6.65 μm. A detailed investigation of the material's structural, morphologic, electronic, and magnetic properties using x-ray powder diffraction, powder neutron diffraction, x-ray absorption near edge structure spectroscopy, scanning electron microscopy, and ac and dc magnetometry has revealed a systematic enhancement of the exchange bias effect with increasing the average grain size. This evolution is discussed in terms of changes in the material's porosity and grain morphology and its influence on the exchange couplings at the magnetic interfaces.

14 SOLAR ENERGY↗
DOE OSTI2024

Optimization and purification of magnesium borides fabricated by combustion synthesis and by high-temperature sintering

Hydrogen as a fuel provides several benefits over the use of fossil fuels; however, one challenge in utilizing hydrogen as an energy carrier revolves around its storage. Achieving sufficient volumetric hydrogen density in a storage solution will facilitate hydrogen’s adoption for use in both stationary and mobile applications. Solid-state hydrogen storage provides a promising pathway to solving this problem. However, the hydrogenation of these materials is characterized by slow kinetics and extreme thermodynamic conditions. Magnesium borohydride (Mg(BH4)2) is a promising material in hydrogen storage due to its reversible properties and a theoretical hydrogen capacity of 14.9 wt.%. To synthesize this material, combustion synthesis of magnesium borides (MgBx) has been implemented with the aim to further lower thermodynamic requirements for direct hydrogenation. A drawback of this process is the potential formation of oxide contaminants, which decrease hydrogenation/dehydrogenation and recyclability performance. The present work focuses on identifying parameters useful for reducing contamination and evaluating potential pathways to the purification of magnesium borides with the goal of improving their quality.

Camarena, Miguel Joaquin↗
DOE OSTI2025

Effect of high scandium doping in barium zirconate on nickel diffusion and performance of proton-conducting solid oxide electrolyzer cells

Proton-conducting solid oxide electrolyzer cells (p-SOECs) are emerging but promising technologies for hydrogen production. However, due to the lack of a robust electrolyte, p-SOECs struggle simultaneously to display high performance, Faradaic efficiency, and durability. Motivated by its high proton concentrations and stability as a barium zirconate, we have investigated BaZr 0.6 Sc 0.4 O 3-δ (BZSc40) as a potential next-generation p-SOEC electrolyte. Here, we found elevated levels of NiO diffusion through BZSc40 electrolytes during high-temperature sintering, attributed to the large oxygen vacancy concentrations present in BZSc40, as revealed by first-principle computational results. Controlling NiO diffusion is critical, as it can facilitate densification and grain size growth, but it may also detrimentally impact performance by causing electronic leakage. By optimizing sintering temperature when fabricating BZSc40 cells, we successfully controlled NiO diffusion, achieving sufficient electrolyte densification along with high performance and Faradaic efficiency. BZSc40 cells reached −0.99 A/cm 2 at 1.3 V and 600 °C and exhibited enhanced durability with a 3.37 mV/kh degradation rate at −0.8 A/cm 2 over a 200-h testing period. BZSc40 electrolytes demonstrated superior performance over BaZr 0.8 Y 0.2 O 3-δ (BZY20). In addition to elevated current densities and grain sizes, BZSc40 cells achieved Faradaic efficiencies of 76 % compared to 54 % for BZY20 at −0.2 A/cm 2 and 600 °C. This work lays the foundation for BZSc40 as a potential electrolyte due to its advantages over BZY20 while demonstrating the significance of controlling NiO diffusion when fabricating p-SOECs.

Electrolyzer↗
DOE OSTI2024

Phase Field Modeling of Pressure Induced Densification in Solid Electrolytes

Adoption of dense and homogeneous solid electrolytes can possibly mitigate the propagation of lithium dendrites and enable lithium metal anodes. Application of external pressure helps to minimize the sintering temperature in oxide ceramics and can potentially densify softer sulfide electrolytes even under room temperature conditions. Here, a previously developed phase field-based computational scheme for predicting the high-temperature sintering-induced densification of oxide ceramic solid electrolytes is extended in the present context to capture the influence of external pressure for densifying solid electrolytes. Two different bulk deformation mechanisms, namely, "reorganization" and "creep deformation," are dominant under external pressure, which is different from the surface and grain-boundary diffusion-induced densification of solid electrolytes that occurs during high temperature sintering. External pressure also increases the points of contact between the particles, which further enhances the propensity of diffusion-induced sintering process. Results obtained from simulations indicate that densification under external pressure is independent of the solid electrolyte particle morphology. Finally, a phase map is generated between applied pressure and temperature for achieving complete densification of oxide ceramics, which can possibly guide the synthesis of thin and dense solid electrolyte separators.

25 ENERGY STORAGE↗
DOE OSTI2020

Unravelling the sintering temperature-induced phase transformations in Ba(Fe 0.7 Ta 0.3 )O 3-δ ceramics

This work reports on the fundamental details of the crystal structure and phase transformations in Ba(Fe 0.7 Ta 0.3 )O 3-δ , the best known temperature-independent oxygen-sensing ceramic material for applications in extreme environments. Ba(Fe 0.7 Ta 0.3 )O 3-δ ceramics were synthesized using conventional solid-state ceramic reaction under variable sintering temperatures (T s = 1200–1350 °C). Combined X-ray diffraction (XRD) and high-resolution transmission electron microscopy (TEM) measurements revealed the T s -induced phase transformations and their origin in Ba(Fe 0.7 Ta 0.3 )O 3-δ . Associated with phase transformations, pseudo-cubic (PC) reflections, such as {200} PC , {211} PC , and {220} PC , exhibited distinct anomalies with increasing T s . At T s = 1200 °C, Ba(Fe 0.7 Ta 0.3 )O 3-δ stabilized in mixed orthorhombic + rhombohedral phases (Amm2 + R3m). With increasing T s (≥1250 °C), Ba(Fe 0.7 Ta 0.3 )O 3-δ ceramics stabilized in tetragonal/rhombohedral [P4mm + R3m] mixed phases, while variations in the quantity of the respective phases were observed. Because both structure and crystal chemistry play key roles in achieving enhanced performance in chemical sensing and catalytic converters, detailed understanding of the phase transformations and crystal structure of Ba(Fe 0.7 Ta 0.3 )O 3-δ ceramics, as derived in this work, will be useful to develop chemical sensors with optimum performance for high-temperature and corrosive environments.

36 MATERIALS SCIENCE↗