Search NASA⌕ Search

SEARCH · Search NASA

Results for “site quality”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2012

Two Years of Simultaneous K(sub a)-Band Measurements: Goldstone, CA; White Sands, NM; and Guam, USA

In order to statistically characterize the effect of the Earth's atmosphere on Ka-Band links, site test interferometers (STIs) have been deployed at three of NASA s operational sites to directly measure each site's tropospheric phase stability and rain attenuation. These STIs are composed of two antennas on a short baseline (less than 1km) that observe the same unmodulated beacon signal broadcast from a geostationary satellite (e.g., Anik F2). The STIs are used to measure the differential phase between the two received signals as well as the individual signal attenuation at each terminal. There are currently three NASA sites utilizing STIs; the Goldstone Deep Space Communications Complex near Barstow, California; the White Sands Complex in Las Cruces, New Mexico; and the Guam Remote Ground Terminal on the island of Guam. The first two sites are both located in desert regions that have highly similar climates in terms of their seasonal temperatures, average humidity, and annual rain fall (the primary factors in determining phase stability). In contrast, Guam is in a tropical region with drastically higher annual rainfall and humidity. Five station years of data have been collected in Goldstone, three in White Sands, and two in Guam, yielding two years of simultaneous data collection across all three sites. During this period of simultaneous data collection, the root-mean-square (RMS) of the time delay fluctuations stayed under 2.40 picoseconds for 90% of the time in Goldstone, under 2.07 picoseconds for 90% of the time in White Sands, and under 10.13 picoseconds for 90% of the time in Guam. For the 99th percentile, the statistics were 6.32 ps, 6.03 ps, and 24.85 ps, respectively. These values, as well as various other site quality characteristics, will be used to determine the suitability of these sites for NASA s future communication services at Ka-Band.

Acosta, Roberto J.↗
NASA NTRS2010

Path Length Fluctuations Derived from Site Testing Interferometer Data

To evaluate possible sites for NASA's proposed Ka-band antenna array, the NASA Glenn Research Center has constructed atmospheric phase monitors (APM) which directly measure the tropospheric phase stability. These instruments observe an unmodulated 20.2 GHz beacon signal broadcast from a geostationary satellite (Anik F2) and measure the phase difference between the signals received by the two antennas. Two APM's have been deployed, one at the NASA Deep Space Network (DSN) Tracking Complex in Goldstone, California, and the other at the NASA White Sands Complex, in Las Cruces, New Mexico. Two station-years of atmospheric phase fluctuation data have been collected at Goldstone since operations commenced in May 2007 and 0.5 station-years of data have been collected at White Sands since operations began February 2009. With identical instruments operating simultaneously, we can directly compare the phase stability at the two sites. Phase stability is analyzed statistically in terms of the root-mean-square (rms) of the tropospheric path length fluctuations over 10 min blocks. Correlation between surface wind speed and relative humidity with interferometer phase are discussed. For 2 years, the path length fluctuations at the DSN site in Goldstone, California, have been better than 757 micrometer (with reference to a 300 m baseline and to Zenith) for 90 percent of the time. For the 6 months of data collected at White Sands, New Mexico, the path length fluctuations have been better than 830 micrometers (with reference to a 300 m baseline and to Zenith) for 90 percent of the time. This type of data analysis, as well as many other site quality characteristics (e.g., rain attenuation, infrastructure, etc.), will be used to determine the suitability of both sites for NASA s future communication services at Ka-band using an array of antennas.

Acosta, Roberto J.↗
NASA NTRS2011

Simultaneous Ka-Band Site Characterization: Goldstone, CA, White Sands, NM, and Guam, USA

To statistically characterize atmospheric effects on Ka-band links at NASA operational sites, NASA has constructed site test interferometers (STI s) which directly measure the tropospheric phase stability and rain attenuation. These instruments observe an unmodulated beacon signal broadcast from a geostationary satellite (e.g., Anik F2) and measure the phase difference between the signals received by the two antennas and its signal attenuation. Three STI s have been deployed so far: the first one at the NASA Deep Space Network Tracking Complex in Goldstone, California (May 2007); the second at the NASA White Sands Complex, in Las Cruses, New Mexico (February 2009); and the third at the NASA Tracking and Data Relay Satellite (TDRS) Remote Ground Terminal (GRGT) complex in Guam (May 2010). Two station-years of simultaneous atmospheric phase fluctuation data have been collected at Goldstone and White Sands, while one year of data has been collected in Guam. With identical instruments operating simultaneously, we can directly compare the phase stability and rain attenuation at the three sites. Phase stability is analyzed statistically in terms of the root-mean-square (rms) of the tropospheric induced time delay fluctuations over 10 minute blocks. For two years, the time delay fluctuations at the DSN site in Goldstone, CA, have been better than 2.5 picoseconds (ps) for 90% of the time (with reference to zenith), meanwhile at the White Sands, New Mexico site, the time delay fluctuations have been better than 2.2 ps with reference to zenith) for 90% of time. For Guam, the time delay fluctuations have been better than 12 ps (reference to zenith) at 90% of the time, the higher fluctuations are as expected from a high humidity tropical rain zone. This type of data analysis, as well as many other site quality characteristics (e.g., rain attenuation, infrastructure, etc.) will be used to determine the suitability of all the sites for NASA s future communication services at Ka-band.

Acosta, Roberto↗
NASA NTRS1994

BSM Delta Qualification 2, volume 2

This report, presented in three volumes, provides the results of a two-motor Delta Qualification 2 program conducted in 1993 to certify the following enhancements for incorporation into booster separation motor (BSM) flight hardware: vulcanized-in-place nozzle aft closure insulation; new iso-static ATJ bulk graphite throat insert material; adhesive EA 9394 for bonding the nozzle throat, igniter grain rod/centering insert/igniter case; deletion of the igniter adapter insulator ring; deletion of the igniter adapter/igniter case interface RTV; and deletion of loctite from igniter retainer plate threads. The enhancements above directly resulted from (1) the BSM total quality management (TQM) team initiatives to enhance the BSM producibility, and (2) the necessity to qualify new throat insert and adhesive systems to replace existing materials that will not be available. Testing was completed at both the component and motor levels. Component testing was accomplished to screen candidate materials (e.g., throat materials, adhesive systems) and to optimize processes (e.g., aft closure insulator vulcanization approach) prior to their incorporation into the test motors. Motor tests -- consisting of two motors, randomly selected by USBI's on-site quality personnel from production lot AAY, which were modified to accept the enhancements -- were completed to provide the final qualification of the enhancements for incorporation into flight hardware. Volume 2 details the environmental testing (vibration and shock) conducted at Marshall Space Flight Center (MSFC) to which the motors were subjected prior to static tests.

Source record↗
NASA NTRS1994

BSA Delta Qualification 2, volume 3, book 1

This report, presented in three volumes, provides the results of a two-motor Delta Qualification 2 program conducted in 1993 to certify the following enhancements for incorporation into booster separation motor (BSM) flight hardware: vulcanized-in-place nozzle aft closure insulation; new iso-static ATJ bulk graphite throat insert material; adhesive EA 9394 for bonding the nozzle throat, igniter grain rod/centering insert/igniter case; deletion of the igniter adapter insulator ring; deletion of the igniter adapter/igniter case interface RTV; and deletion of Loctite from igniter retainer plate threads. The enhancements above directly resulted from (1) the BSM total quality management (TQM) team initiatives to enhance the BSM producibility, and (2) the necessity to qualify new throat insert and adhesive systems to replace existing materials that will not be available. Testing was completed at both the component and motor levels. Component testing was accomplished to screen candidate materials (e.g., throat materials, adhesive systems) and to optimize processes (e.g., aft closure insulator vulcanization approach) prior to their incorporation into the test motors. Motor tests -- consisting of two motors, randomly selected by USBI's on-site quality personnel from production lot AAY, which were modified to accept the enhancements -- were completed to provide the final qualification of the enhancements for incorporation into flight hardware. Volume 3 book 1 provides supporting documentation to the analyses and plans of testing the two Delta Qualification units including thermal cycling planning/data acceptance records, environmental test procedures and pretest temperature conditioning history, Delta Qualification test plan, and specification SE0837 -- mix acceptance test specification.

Source record↗
NASA NTRS1994

BSM Delta Qualification 2, volume 3, book 2

This report, presented in three volumes, provides the results of a two-motor Delta Qualification 2 program conducted in 1993 to certify the following enhancements for incorporation into booster separation motor (BSM0 flight hardware: vulcanized-in-place nozzle aft closure insulation; new iso-static ATJ bulk graphite throat insert material, adhesive EA9394 for bonding the nozzle throat, igniter grain rod/centering insert/igniter case; deletion of the igniter adapter insulator ring; deletion of the igniter adapter/igniter case interface RTV; and deletion of loctite from igniter retainer plate threads. The enhancements above directly resulted from (1) the BSM total quality management (TQM) team initiatives to enhance the BSM producibility, and (2) the necessity to qualify new throat insert and adhesive systems to replace existing materials that will not be available. Testing was completed at both the component and motor levels. Component testing was accomplished to screen candidate materials (e.g., throat materials, adhesive systems) and to optimize processes (e.g., aft closure insulator vulcanization approach) prior to their incorporation into the test motors. Motor testing--consisting of two motors, randomly selected by USBI's on-site quality personnel from production lot AAY, which were modified to accept the enhancements -- was completed to provide the final qualification of the enhancements for incorporation into flight hardware. Volume 3, Book 2 provides various supporting documentation to the previous volumes with regards to the testing of the two Delta qualification units: data acceptance records, thermal conditioning analysis, igniter adapter thermal flake analysis, laboratory adhesive (EA-9394) qualification report, throat insert thermal/structural analysis, Delta Qualification Nonconformance Reports (NCR's), O-ring seating tests, and interim test report for vulcanization process qualification.

Source record↗
NASA NTRS1986

Interpreting forest and grassland biome productivity utilizing nested scales of image resolution and biogeographical analysis

Data acquisition, initial site characterization, image and geographic information methods available, and brief evaluations of first-year for NASA's Thematic Mapper (TM) working group are presented. The TM and other spectral data are examined in order to relate local, intensive ecosystem research findings to estimates of carbon cycling rates over wide geographic regions. The effort is to span environments ranging from dry to moist climates and from good to poor site quality using the TM capability, with and without the inclusion of geographic information system (GIS) data, and thus to interpret the local spatial pattern of factors conditioning biomass or productivity. Twenty-eight TM data sets were acquired, archived, and evaluated. The ERDAS image processing and GIS system were installed on the microcomputer (PC-AT) and its capabilities are being investigated. The TM coverage of seven study areas were exported via ELAS software on the Prime to the ERDAS system. Statistical analysis procedures to be used on the spectral data are being identified.

Iverson, L. R.↗
NASA NTRSDate not supplied

Observation of Pollution Events at Low Altitude During TRACER-AQ – The Advantage of Adaptive Resolution Lidar

The TRACER-AQ campaign happened in August-September 2021 in Houston, Texas. Its objective was to better understand the pollution events in the coastal environment and to evaluate models and satellite observations. As a supporting instrument, NASA’s Langley Mobile Ozone Lidar (LMOL) was installed on the Houston campus, adjacent to University of Houston’s air-quality site, and performed observations of ozone and aerosols. Co-located instrumentation included a Pandora spectrophotometer, in-situ trace-gas measurements, and ozonesonde launches. Thanks to an adaptive resolution retrieval scheme, LMOL was able to detect thin-layer O3 structures at low (~200m) altitude that are not captured by the ozonesondes, and would ordinarily be missed with traditional coarse TOLNet lidar vertical averaging. We show that some of these features are not present in the models and are likely coming from local, industry-generated, emissions.

Guillaume Gronoff↗
NASA NTRS1998

Automatic Generation of CFD-Ready Surface Triangulations from CAD Geometry

This paper presents an approach for the generation of closed manifold surface triangulations from CAD geometry. CAD parts and assemblies are used in their native format, without translation, and a part's native geometry engine is accessed through a modeler-independent application programming interface (API). In seeking a robust and fully automated procedure, the algorithm is based on a new physical space manifold triangulation technique which was developed to avoid robustness issues associated with poorly conditioned mappings. In addition, this approach avoids the usual ambiguities associated with floating-point predicate evaluation on constructed coordinate geometry in a mapped space, The technique is incremental, so that each new site improves the triangulation by some well defined quality measure. Sites are inserted using a variety of priority queues to ensure that new insertions will address the worst triangles first, As a result of this strategy, the algorithm will return its 'best' mesh for a given (prespecified) number of sites. Alternatively, the algorithm may be allowed to terminate naturally after achieving a prespecified measure of mesh quality. The resulting triangulations are 'CFD-ready' in that: (1) Edges match the underlying part model to within a specified tolerance. (2) Triangles on disjoint surfaces in close proximity have matching length-scales. (3) The algorithm produces a triangulation such that no angle is less than a given angle bound, alpha, or greater than Pi - 2alpha This result also sets bounds on the maximum vertex degree, triangle aspect-ratio and maximum stretching rate for the triangulation. In addition to tile output triangulations for a variety of CAD parts, tile discussion presents related theoretical results which assert the existence of such all angle bound, and demonstrate that maximum bounds of between 25 deg and 30 deg may be achieved in practice.

Aftosmis, M. J.↗
NASA NTRSDate not supplied

Analysis of Atmospheric Conditions Responsible for an Ozone Exceedance Event in Southeast Virginia on June 15, 2022

On June 15, 2022, the Virginia Department of Environmental Quality monitoring site at Suffolk/Holland, a rural site in southeast Virginia, recorded its first ozone exceedance since 2016. An ozone exceedance day occurs when the daily maximum 8-hour average surface ozone concentration is greater than 70 ppb. On this day, it was 75 ppb. This event is also noteworthy due to the rapid increase in surface ozone between 6 am and 9 am EDT as well as the hourly maximum ozone concentration of 82 ppb that was measured at 1 pm EDT. In this analysis, we utilize various observational and model data to determine the atmospheric conditions responsible for this ozone exceedance event. The analysis is conducted in two parts: (1) an evaluation of the accuracy of the GEOS-CF and WRF-Chem model forecasts and (2) an investigation of the mechanisms responsible for the high surface ozone at the Virginia DEQ Suffolk/Holland monitoring site. Comparisons of model forecasted ozone time-height cross sections with measured ozone by lidars from the Tropospheric Ozone Lidar Network (TOLNet) at NASA Langley and NASA Goddard reveal that both models forecasted ozone reasonably well near the surface. Model and observational data reveal that an upper-level ridge was present over much of the eastern United States, with a broad anticyclonic circulation near the surface, resulting in north-northeasterly flow over southeast Virginia. Back trajectory calculations using the Hybrid Single-Particle Lagrangian Integrated Trajectory model (HYSPLIT) and model data suggest that a low-level plume rich in ozone and precursor species originating from the New York City and New Jersey region was transported along the east coast between June 14 and June 15, arriving in southeast Virginia around 6 am EDT on June 15. In the early morning hours, this plume mixed down to the surface, elevating the background ozone mixing ratio as well as the mixing ratios of several precursor species. Other potential contributions are also explored and discussed. Lastly, the authors note that this work represents the analysis of the authors and not the Virginia Department of Environmental Quality.

Daniel B Phoenix↗
NASA NTRSDate not supplied

Using Machine Learning to Estimate Surface-Level SO2 Concentrations from Satellite-Based Measurements

Sulfur dioxide (SO2) is a criteria air pollutant due to its contributions to aerosol formation, rainfall acidification, and harm to human health. The placement of air quality monitoring sites is typically biased towards urban areas, leaving large areas with very limited monitoring data. The Ozone Monitoring Instrument (OMI) has been used to provide estimates of SO2 vertical column densities (VCDs) globally at spatial resolution of 10s of kms once per day. OMI SO2 VCDs have been previously used to estimate surface SO2 concentrations using chemical transport model (CTM) simulations. The CTMs use estimated emissions and assimilated meteorological data, and simulate the chemical and physical processes that determine the vertical profile of SO2, which can be used to derive a ratio between the surface concentrations and VCDs. These models are complex, computationally expensive, and have large uncertainties in the simulated surface-to-VCD ratio due to biases in emissions and relatively coarse resolution. Machine learning techniques are comparatively easier to use, much less computationally expensive to use after training, and can produce more accurate estimations of surface concentrations than the CTM-based method. The interpretation of machine learning models often poses challenges, and in some cases, non-physical variables unrelated to SO2 are used as predictors. In this work, we create an artificial neural network (ANN) to relate OMI retrievals and archived GEOS-FP boundary layer heights to surface SO2 concentrations from the ChinaHighAirPollutants ChinaHighSO2 dataset (CHAP; Wei et al., 2023) on a seasonal average timescale from 2013-2018. Our model only utilizes five variables that are directly relevant to the satellite retrieval, lifetime, and spatial distribution of SO2. The model was trained on 16 seasons (four of each) with independent validation (one of each season) and testing datasets (one of each season) to avoid overfitting. Our ANN generates surface SO2 concentrations that are sensitive (slope = 0.51) and consistent (r = 0.74) with the CHAP data, but are underpredicted by an average of 1.2 ppbv with a mean absolute error of 2.2 ppbv. These results are better than recent studies utilizing the CTM method. To our knowledge, this is the best performing machine learning model that only uses physical variables to predict surface SO2. Our work demonstrates that a carefully constructed, simple ML model can accurately estimate surface-based SO2 concentrations from satellite VCD measurements, and this technique has future promise to expend to newer, higher resolution satellites and other air pollutants.

SO2, air quality, OMI, machine learning↗
NASA NTRS1996

A Conservation Strategy for the Florida Scrub-Jay on John F. Kennedy Space Center/Merritt Island National Wildlife Refuge: An Initial Scientific Basis for Recovery

The Florida Scrub-Jay (Aphelocoma coerulescens) is an indicator of ecosystem integrity of Florida scrub, an endangered ecosystem that requires frequent fire. One of the largest populations of this federally threatened species occurs on John F. Kennedy Space Center/Merritt Island National Wildlife Refuge. Population trends were predicted using population modeling and field data on reproduction and survival of Florida Scrub-Jays collected from 1988 - 1995. Analyses of historical photography indicated that habitat suitability has been declining for 30 years. Field data and computer simulations suggested that the population declined by at least 40% and will decline by another 40% in 1 0 years, if habitat management is not greatly intensified. Data and computer simulations suggest that habitat suitability cannot deviate greatly from optimal for the jay population to persist. Landscape trajectories of vegetation structure, responsible for declining habitat suitability, are associated with the disruption of natural fire regimes. Prescribed fire alone can not reverse the trajectories. A recovery strategy was developed, based on studies of Florida Scrub-Jays and scrub vegetation. A reserve design was formulated based on conservation science principles for scrub ecosystems. The strategy emphasizes frequent fire to restore habitat, but includes mechanical tree cutting for severely degraded areas. Pine thinning across large areas can produce rapid increases in habitat quality. Site-specific strategies will need to be developed, monitored, and modified to achieve conditions suitable for population persistence.

Breininger, D. R.↗
NASA NTRS1999

Dependence of Z-R Relations on the Rain Type Classification Scheme

The TRMM Global Validation Program is giving us a unique opportunity to compare radar datasets from different sites since they are analyzed in a relatively uniform procedure. Monthly Ze-R relations for four different sites (i.e, Melbourne Florida, Houston Texas, Darwin Australia and Kwajalein Atoll) were derived. The relations were obtained using the Window Probability Matching Method (WPMM). This version of the PMM relies on matching unconditional probabilities of rain rates, R, and radar reflectivity, Ze, using rain gauge and radar data, respectively. This procedure was done separately for convective and stratiform rain type using the Steiner classification procedure. The radar and gauge data from all sites were quality controlled using the same algorithms, which include also an automatic procedure to filter unreliable rain gauge data upon comparison to radar data. An adjusted power law Z-R for each rain type was also derived by comparing the radar-gauge coincident pairs in order to adjust the total monthly rainfall to match the gauges. The obtained PMM based Ze-R relations are found to be curved lines in log-log space rather than any straight line power law. While the PMM based Ze-R curves were always distinctly different between the convective and stratiform rain, the power law based Z-R, in few cases, was found to be the same for both types. In general, a given reflectivity was matched to a much lower rain intensity in the convective rainfall as compared to that in stratiform rainfall. These findings are inherently contradictory to previous findings based on disdrometer data and suggest some precaution for using the latter Z-R relations on radar data when the partition of stratiform and convective rainfall amount is in concern. The inverse trends in the relations might be caused by effects such as partial beam fillings, the use of different classification schemes, as well as having a distinct difference in the Z-R relations between the initial convective and the trailing transition regions as suggested by recent findings.

Amitai, Eyal↗
NASA NTRS1975

USDI DCS technical support: Mississippi Test Facility

The objective of the technical support effort is to provide hardware and data processing support to DCS users so that application of the system may be simply and effectively implemented. Technical support at Mississippi Test Facility (MTF) is concerned primarily with on-site hardware. The first objective of the DCP hardware support was to assure that standard measuring apparatus and techniques used by the USGS could be adapted to the DCS. The second objective was to try to standardize the miscellaneous variety of parameters into a standard instrument set. The third objective was to provide the necessary accessories to simplify the use and complement the capabilities of the DCP. The standard USGS sites have been interfaced and are presently operating. These sites are stream gauge, ground water level and line operated quality of water. Evapotranspiration, meteorological and battery operated quality of water sites are planned for near future DCP operation. Three accessories which are under test or development are the Chu antenna, solar power supply and add-on memory. The DCP has proven to be relatively easy to interface with many monitors. The large antenna is awkward to install and transport. The DCS has met the original requirements well; it has and is proving that an operation, satellite-based data collection system is feasible.

Preble, D. M.↗
NASA NTRS2018

Linking Improvements in Sulfur Dioxide Emissions to Decreasing Sulfate Wet Deposition by Combining Satellite and Surface Observations with Trajectory Analysis

Sulfur dioxide (SO2), a criteria pollutant, and sulfate (SO42) deposition are major environmental concerns in the eastern U.S. and both have been on the decline for two decades. In this study, we use satellite column SO2 data from the Ozone Monitoring Instrument (OMI), and SO42 wet deposition data from the NADP (National Atmospheric Deposition Program) to investigate the temporal and spatial relationship between trends in SO2 emissions and the downward sulfate wet deposition over the eastern U.S. from 2005 to 2015. To establish the relationship between SO2 emission sources and receptor sites, we conducted a Potential Source Contribution Function (PSCF) analysis using HYSPLIT back trajectories for five selected Air Quality System (AQS) sites - (Hackney, OH, Akron, OH, South Fayette, PA, Wilmington, DE, and Beltsville, MD) - in close proximity to NADP sites with large downward SO42 trends since 2005. Back trajectories were run for three summers (JJA) and three winters (DJF) and used to generate seasonal climatology PSCFs for each site. The OMI SO2 and interpolated NADP sulfate deposition trends were normalized and overlapped with the PSCF, to identify the areas that had the highest contribution to the observed drop. The results suggest that emission reductions along the Ohio River Valley have led to decreases in sulfate deposition in eastern OH and western PA (Hackney, Akron and South Fayette). Farther to the east, emission reductions in southeast PA resulted in improvements in sulfate deposition at Wilmington, DE, while for Beltsville, reductions in both the Ohio River Valley and nearby favorably impacted sulfate deposition. For Beltsville, sources closer than 300km from the site contribute roughly 56% observed deposition trends in winter, and 82% in summer, reflecting seasonal changes in transport pattern as well as faster oxidation and washout of sulfur in summer. This suggests that emissions and wet deposition are linked through not only the location of sources relative to the observing sites, but also to photochemistry and the weather patterns characteristic to the region, as evidenced by a west to east shift in the contribution between winter and summer. The method developed here is applicable to other regions with significant trends such as China and India, and can be used to estimate the potential benefits of emission reduction in those areas.

Acid depostion↗
NASA NTRS2018

Linking Improvements in Sulfur Dioxide Emissions to Decreasing Sulfate Wet Deposition By Combining Satellite and Surface Observations With Trajectory Analysis

Sulfur dioxide (SO2), a criteria pollutant, and sulfate (SO42−) deposition are major environmental concerns in the eastern U.S. and both have been on the decline for two decades. In this study, we use satellite column SO2 data from the Ozone Monitoring Instrument (OMI), and SO42− wet deposition data from the NADP (National Atmospheric Deposition Program) to investigate the temporal and spatial relationship between trends in SO2 emissions and the downward sulfate wet deposition over the eastern U.S. from 2005 to 2015. To establish the relationship between SO2 emission sources and receptor sites, we conducted a Potential Source Contribution Function (PSCF) analysis using HYSPLIT back trajectories for five selected Air Quality System (AQS) sites - (Hackney, OH, Akron, OH, South Fayette, PA, Wilmington, DE, and Beltsville, MD) - in close proximity to NADP sites with large downward SO42− trends since 2005. Back trajectories were run for three summers (JJA) and three winters (DJF) and used to generate seasonal climatology PSCFs for each site. The OMI SO2 and interpolated NADP sulfate deposition trends were normalized and overlapped with the PSCF, to identify the areas that had the highest contribution to the observed drop. The results suggest that emission reductions along the Ohio River Valley have led to decreases in sulfate deposition in eastern OH and western PA (Hackney, Akron and South Fayette). Farther to the east, emission reductions in southeast PA resulted in improvements in sulfate deposition at Wilmington, DE, while for Beltsville, reductions in both the Ohio River Valley and nearby favorably impacted sulfate deposition. For Beltsville, sources closer than 300 km from the site contribute roughly 56% observed deposition trends in winter, and 82% in summer, reflecting seasonal changes in transport pattern as well as faster oxidation and washout of sulfur in summer. This suggests that emissions and wet deposition are linked through not only the location of sources relative to the observing sites, but also to photochemistry and the weather patterns characteristic to the region, as evidenced by a west to east shift in the contribution between winter and summer. The method developed here is applicable to other regions with significant trends such as China and India, and can be used to estimate the potential benefits of emission reduction in those areas.

sulfur dioxide emissions↗
NASA NTRS2020

Spatiotemporal Characteristics of the Association between AOD and PM over the California Central Valley

Many air pollution health effects studies rely on exposure estimates of particulate matter (PM) concentrations derived from remote sensing observations of aerosol optical depth (AOD). Simple but robust calibration models between AOD and PM are therefore important for generating reliable PM exposures. We conduct an in-depth examination of the spatial and temporal characteristics of the AOD-PM2.5 relationship by leveraging data from the Distributed Regional Aerosol Gridded Observation Networks (DRAGON) field campaign where eight NASA Aerosol Robotic Network (AERONET) sites were co-located with EPA Air Quality System (AQS) monitoring sites in California’s Central Valley from November 2012 to April 2013. With this spatiotemporally rich data we found that linear calibration models (R(exp 2) = 0.35, RMSE = 10.38 µg/cu.m) were significantly improved when spatial (R(exp 2) = 0.45, RMSE = 9.54 µg/cu.m), temporal (R(exp 2) = 0.62, RMSE = 8.30 µg/cu.m), and spatiotemporal (R(exp 2) = 0.65, RMSE = 7.58 µg/cu.m) functions were included. As a use-case we applied the best spatiotemporal model to convert space-borne MultiAngle Imaging Spectroradiometer (MISR) AOD observations to predict PM2.5 over the region (R(exp 2) = 0.60, RMSE = 8.42 µg/cu.m). Our results imply that simple AERONET AOD-PM2.5 calibrations are robust and can be reliably applied to space-borne AOD observations, resulting in PM2.5 prediction surfaces for use in downstream applications.

Meytar Sorek-Hamer↗