SEARCH · Search NASA

Results for “size reduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

All sources NASA NTRS DOE OSTI

NASA NTRS1990

Effect of tail size reductions on longitudinal aerodynamic characteristics of a three surface F-15 model with nonaxisymmetric nozzles

An investigation was conducted in the Langley 16-Foot Transonic Tunnel to determine the effects of horizontal and vertical tail size reductions on the longitudinal aerodynamic characteristics of a modified F-15 model with canards and 2-D convergent-divergent nozzles. Quantifying the drag decrease at low angles of attack produced by tail size reductions was the primary focus. The model was tested at Mach numbers of 0.40, 0.90, and 1.20 over an angle of attack of -2 degree to 10 degree. The nozzle exhaust flow was simulated using high pressure air at nozzle pressure ratios varying from 1.0 (jet off) to 7.5. Data were obtained on the baseline configuration with and without tails as well as with reduced horizontal and/or vertical tail sizes that were 75, 50, and 25 percent of the baseline tail areas.

Frassinelli, Mark C.↗

NASA NTRS1992

Size-reduction techniques for the determination of efficient aeroservoelastic models

Size-reduction techniques for determining efficient time-domain state-space aeroservoelastic models are presented. Various rational function approximation methods of the unsteady aerodynamic force coefficients are brought to a common motion, emphasizing their differences. Among these, the classic Roger's method is the easier to apply but its resulting number of aerodynamic states is typically equal to or larger than the number of structural states. On the other hand, the minimum-state (MS) method, which typically reduces the number of aerodynamic states by 70 percent or more, requires the solution of an iterative nonlinear least-square solution. The MS computational efforts are reduced significantly when three approximation constraints are applied.

Karpel, Mordechay↗

NASA NTRS2003

The effect of drying and size reduction pretreatments on recovery of inorganic crop nutrients from inedible wheat residues

Inorganic nutrients can be easily recovered from ALS crop residue solid wastes by aqueous leaching. However, oven drying and milling pretreatment of these residues has been frequently required to accommodate crop scientists and facility storage limitations. As part of a research study that will compare three different bioreactor technologies for processing these wastes, we realized that different drying and size-reduction pretreatments had been utilized for each technology. This paper compares the effects of residue pretreatment on recovery of nutrients by leaching. Pretreatments included three drying methods [fresh, oven-dried (70 degrees C overnight), and freeze-dried] and two size reduction methods [chopped (2 cm length) and milled (2 mm diameter)]. Determination of mass balances (dry weight and ash content of solids) before and after leaching indicated solubilization was least for fresh residues (23% dry weight loss and 50% for ash loss), and most for freeze-dried residues (41-47% dry weight loss and nearly 100% for ash loss). Mineral recovery of major elements (NO3, PO4, K, Ca, and Mg) in leachates was poorest for fresh residues. P and K recovery in leachates were best for oven-dried residues and Ca, Mg, and N recovery best for freeze-dried residues. The differences in recovery for N, P, and K in leachates were minimal between chopping and milling and slightly better for Ca and Mg from milled residues.

NASA Center KSC↗

NASA NTRS1964

A-c to d-c power supply using high-frequency techniques for size reduction.

AC to DC power supply using high frequency transistor circuit techniques for size reduction by which conversion, filtering and regulation may be combined

POWER CONVERSION↗

NASA NTRS1986

Particle size reduction of Si3N4 with Si3N4 milling hardware

The grinding of Si3N4 powder using reaction bonded Si3N4 attrition, vibratory, and ball mills with Si3N4 media was examined. The rate of particle size reduction and the change in the chemical composition of the powder were determined in order to compare the grinding efficiency and the increase in impurity content resulting from mill and media wear for each technique. Attrition and vibratory milling exhibited rates of specific surface area increase that were approximately eight times that observed in ball milling. Vibratory milling introduced the greatest impurity pickup.

Herbell, T. P.↗

NASA NTRS1986

Particle-size reduction of Si3N4 powder with Si3N4 milling hardware

Herbell, T. P.↗

NASA NTRS1986

Model-size reduction for the buckling and vibration analyses of anisotropic panels

A computational procedure is presented for reducing the size of the model used in the buckling and vibration analyses of symmetric anisotropic panels to that of the corresponding orthotropic model. The key elements of the procedure are the application of an operator splitting technique through the decomposition of the material stiffness matrix of the panel into the sum of orthotropic and nonorthotropic (anisotropic) parts and the use of a reduction method through successive application of the finite element method and the classical Rayleigh-Ritz technique. The effectiveness of the procedure is demonstrated by numerical examples.

Noor, A. K.↗

NASA NTRS1985

Model-size reduction technique for the analysis of symmetric anisotropic structures

A two-step computational procedure is presented for reducing the size of the analysis model for an anisotropic symmetric structure to that of the corresponding orthotropic structure. The key elements of the procedure are: (1) decomposition of the stiffness matrix into the sum of an orthotropic and nonorthotropic (anisotropic) parts; and (2) successive application of the finite element method and the classical Rayleigh-Ritz technique. The finite element method is first used to generate few global approximation vectors (or modes). Then the amplitudes of these modes are computed by using the Rayleigh-Ritz technique. The global approximation vectors are selected to be the solution corresponding to zero nonorthotropic matrix and its various-order derivatives with respect to an anisotropic tracing parameter (identifying the nonorthotropic material coefficients). The size of the analysis model used in generating the global approximation vectors is identical to that of the corresponding orthotropic structure. The effectiveness of the proposed technique is demonstrated by means of numerical examples and its potential for solving other quasi-symmetric problems is discussed.

Noor, A. K.↗

NASA NTRS1987

Model-size reduction for the analysis of symmetric structures with asymmetric boundary conditions

A simple computational procedure is presented for reducing the size of the analysis model for a symmetric structure with asymmetric boundary conditions to that of the corresponding structure with symmetric boundary conditions. The procedure is based on approximating the asymmetric response of the structure by a linear combination of symmetric and antisymmetric global approximation vectors (or modes). The key elements of the procedure are (1) restructuring the governing finite-element equations to delineate the contributions to the symmetric and antisymmetric components of the asymmetric response, (2) successive application of the finite element method and the classical Rayleigh-Ritz technique. The finite-element method is first used to generate a few global approximation vectors (or modes). Then the amplitudes of these modes are computed by using the Rayleigh-Ritz technique. The effectiveness of the computational procedure is demonstrated by means of numerical examples of linear static problems of shells, and its potential for solving nonlinear problems is discussed.

Noor, Ahmed K.↗

NASA NTRS1987

Model-size reduction for the non-linear dynamic analysis of quasi-symmetric structures

A numerical technique is developed to reduce the size of models describing the nonlinear dynamic response of quasi-symmetric structures (i.e., structures with unsymmetric geometry). The response vectors of the structure are approximated by a linear combination of the symmetric and antisymmetric vectors at each time step. The mathematical formulation and numerical implementation of the method are described in detail, and results for a shallow laminated anisotropic panel of quadrilateral planform are presented in graphs and normalized contour plots.

Noor, Ahmed K.↗

NASA NTRS1977

Structured estimation - Sample size reduction for adaptive pattern classification

The Gaussian two-category classification problem with known category mean value vectors and identical but unknown category covariance matrices is considered. The weight vector depends on the unknown common covariance matrix, so the procedure is to estimate the covariance matrix in order to obtain an estimate of the optimum weight vector. The measure of performance for the adapted classifier is the output signal-to-interference noise ratio (SIR). A simple approximation for the expected SIR is gained by using the general sample covariance matrix estimator; this performance is both signal and true covariance matrix independent. An approximation is also found for the expected SIR obtained by using a Toeplitz form covariance matrix estimator; this performance is found to be dependent on both the signal and the true covariance matrix.

Morgera, S.↗

NASA NTRS1992

Grain size reduction in granular flows of spheres - The effects of critical impact energy

Methods employed to derive recent kinetic theories for rapid noncomminuting granular flows are extended to homogeneous flows in which a fraction of the repeated collisions produce tiny fractures on the particles' peripheries and gradually reduce their effective diameters. The theory consists of balance equations for mass, momentum, and energy, as well as constitutive relations for the presence tensor and collisional rates of mass and energy lost. The work of Richman and Chou (1989) is improved by incorporating into the constitutive theory the critical impact energy below which no mass loss occurs in a binary collision. The theory is applied to granular shear flows and, for fixed shear rates, predicts the time variations of the solid fraction granular temperature, and induced stresses, as well as their extreme sensitivities to small changes in the critical impact energy.

Richman, M. W.↗

NASA NTRS1993

Production of Ultrafine, High-purity Ceramic Powders Using the US Bureau of Mines Developed Turbomill

Turbomilling, an innovative grinding technology developed by the U.S. Bureau of Mines in the early 1960's for delaminating filler-grade kaolinitic clays, has been expanded into the areas of particle size reduction, material mixing, and process reaction kinetics. The turbomill, originally called an attrition grinder, has been used for particle size reduction of many minerals, including natural and synthetic mica, pyrophyllite, talc, and marble. In recent years, an all-polymer version of the turbomill has been used to produce ultrafine, high-purity, advanced ceramic powders such as SiC, Si3N4, TiB2, and ZrO2. In addition to particle size reduction, the turbomill has been used to produce intimate mixtures of high surface area powders and whiskers. Raw materials, TiN, AlN, and Al2O3, used to produce a titanium nitride/aluminum oxynitride (TiN/AlON) composite, were mixed in the turbomill, resulting in strength increases over samples prepared by dry ball milling. Using the turbomill as a leach vessel, it was found that 90.4 pct of the copper was extracted from the chalcopyrite during a 4-hour leach test in ferric sulfate versus conventional processing which involves either roasting of the ore for Cu recovery or leaching of the ore for several days.

Hoyer, Jesse L.↗

NASA NTRS1985

Reduction method for thermal analysis of complex aerospace structures

A reduction method which combines classical Rayleigh-Ritz modal superposition techniques with contemporary finite-element methods is applied to transient nonlinear thermal analysis of aerospace structures. The essence of the method is the use of a few thermal modes from eigenvalue analyses as basis vectors to represent the temperature response in the structure. The method is used to obtain approximate temperature histories for a portion of the Shuttle orbiter wing subject to reentry heating and for a large space antenna reflector subject to heating associated with a low Earth orbit. The reduction method has excellent potential for significant size reduction for radiation-dominated problems such as the antenna reflector. However, for conduction-dominated problems such as the Shuttle wing, especially those with complex spatial and temporal variations in the applied heating, additional work appears necessary to find alternate sources of basis vectors which will permit significant problem size reductions.

Shore, C. P.↗

NASA NTRS1993

Reduction in size and unsteadiness of a VTOL ground vortex by ground fences

A ground vortex, produced when a jet impinges on the ground in the presence of cross flow, is encountered by V/STOL aircraft hovering near the ground and is known to be hazardous to the aircraft. The objective of this research was to identify a ground-based technique by which both the mean size and fluctuation in size of the ground vortex could be reduced. A simple passive method was identified and examined in the laboratory. Specifically, one or two fine wire mesh screens (ground fences) bent in a horseshoe shape and located on the ground in front of the jet impingement point proved to be very effective. The ground fences work by decreasing the momentum of the upstream-traveling wall jet, effectively causing a higher freestream-to-jet velocity ratio (V(sub infinity)/V(sub j)) and thus, a ground vortex smaller in size and unsteadiness. At(V(sub infinity)/V(sub j)) = 0.15, the addition of a single ground fence resulted in a 70 percent reduction in mean size of the ground vortex. With two ground fences, the mean size decreased by about 85 percent. Fluctuations in size decreased nearly in proportion to the mean size, for both the single and double fence configurations. These results were consistent over a wide range of jet Reynolds number (10(exp 4) less than Re(sub jet) less than 10(exp 5)); further development and full-scale Reynolds number testing are required, however, to determine if this technique can be made practical for the case of actual VTOL aircraft.

Cimbala, John M.↗

NASA NTRS1995

Reduction Of Sizes Of Semi-Markov Reliability Models

Trimming technique reduces computational effort by order of magnitude while introducing negligible error. Error bound depends on only three parameters from semi-Markov model: maximum sum of rates for failure transitions leaving any state, maximum average holding time for recovery-mode state, and operating time for system. Error bound computed before any model generated, enabling modeler to decide immediately whether or not model can be trimmed. Trimming procedure specified by precise and easy description, making it easy to include trimming procedure in program generating mathematical models for use in assessing reliability. Typical application of technique in design of digital control systems required to be extremely reliable. In addition to aerospace applications, fault-tolerant design has growing importance in wide range of industrial applications.

White, Allan L.↗

NASA NTRS2003

Unsteady Probabilistic Analysis of a Gas Turbine System

In this work, we have considered an annular cascade configuration subjected to unsteady inflow conditions. The unsteady response calculation has been implemented into the time marching CFD code, MSUTURBO. The computed steady state results for the pressure distribution demonstrated good agreement with experimental data. We have computed results for the amplitudes of the unsteady pressure over the blade surfaces. With the increase in gas turbine engine structural complexity and performance over the past 50 years, structural engineers have created an array of safety nets to ensure against component failures in turbine engines. In order to reduce what is now considered to be excessive conservatism and yet maintain the same adequate margins of safety, there is a pressing need to explore methods of incorporating probabilistic design procedures into engine development. Probabilistic methods combine and prioritize the statistical distributions of each design variable, generate an interactive distribution and offer the designer a quantified relationship between robustness, endurance and performance. The designer can therefore iterate between weight reduction, life increase, engine size reduction, speed increase etc.

Brown, Marilyn↗

NASA NTRS1996

Piezoceramic Microactuation for Robotic Space Exploration

From overview: Current approach for realization of small vehicles is evolutionary: through the miniaturization1 of existing wheeled/legged vehicles based on state of the art in miniature actuators and motors. However, such miniaturization does not lend itself to cost reduction concomitant with the size reduction because cost of the individual mobility components goes up by an order of magnitude or more for such miniature motors etc. which often need to be precisely hand assembled. An alternate approach with significant potential advantages, especially when traversing unusual and difficult terrain such as loose granular surfaes, is to imitate the mobility attributes of insects.

vehicles artificial insects advanced mobility↗