Search NASA⌕ Search

SEARCH · Search NASA

Results for “solar cell performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Improving Solar Cell Performance Using Quantum Dot Triad Charge-Separation Engines

Here, we use kinetic modeling to explore the current–voltage, power–voltage, and power conversion efficiency characteristics of quantum dot dyads and triads as possible light absorption and charge separation engines in quantum dot, bulk heterojunction solar cells. The external and internal power conversion quantum efficiencies are significantly enhanced by introducing a third quantum dot between the donor and acceptor quantum dots. Given the constraint of comparable charge-recombination and charge-separation rates, open-circuit voltages for triads are predicted to be about 10%–17% larger than those for dyads, and short-circuit currents for triads are about 400% larger than those for dyads. These improvements in the efficiencies can be further enhanced by tuning the band-edge energy offset of the middle-position quantum dot from its neighbors. The band-edge energies of the middle quantum dot should be tuned so that they form a cascading band-edge energy alignment from the band-edge energies of the left CdTe QD to the right CdSe QD. To produce the most favorable solar cell performance, the middle quantum dot’s conduction (valence) band edge should be closer to the right quantum dot’s band edge when the charge recombination rates are low (high) and near the conduction (valence) band edge of the left quantum dot when the charge recombination rates are high (low). This analysis identifies prime strategies to design multi-QD assemblies for solar energy harvesting and conversion.

36 MATERIALS SCIENCE↗

Correlations of Capacitance-Voltage Hysteresis with Thin-Film CdTe Solar Cell Performance During Accelerated Lifetime Testing

In this paper we present the correlation of CdTe solar cell performance with capacitance-voltage hysteresis, defined presently as the difference in capacitance measured at zero-volt bias when collecting such data with different pre-measurement bias conditions. These correlations were obtained on CdTe cells stressed under conditions of 1-sun illumination, open-circuit bias, and an accelerationtemperature of approximately 100 degrees C.

14 SOLAR ENERGY↗

Flexible transparent conducting electrodes unexpectedly influence MAPbI 3 film morphology and perovskite solar cell performance

Fabricating perovskite solar cells (PSCs) on plastic substrates will enable cost-effective manufacturing of lightweight and portable energy systems. Here, we study the influence of flexible transparent conductive electrodes (TCEs) on the methylammonium lead iodide (MAPbI3) film morphology and PSC performance. Three types of TCEs on polyethylene terephthalate (PET) are compared: a custom-made AgNWs/indium zinc oxide hybrid TCE and two commercial substrates with indium tin oxide (ITO) or metal/insulator/metal (MIM) as the TCE. Using the same p-i-n architecture and hole transport layer (HTL), we find that PSCs fabricated on the hybrid TCE show better performance and stability compared to those made on commercial TCEs. The PSC performance enhancement is attributed to the superior structural and optical properties of MAPbI3 film deposited on the hybrid TCE, which is explained by the surface energy difference of the HTL. While it is anticipated that solar cell performance can be affected by TCEs’ transmittance and sheet resistance as they determine light absorption and carrier transport, respectively, our finding of TCE influencing the morphology and crystallinity of MAPbI3 film, and hence PSC performance, is unexpected.

14 SOLAR ENERGY↗

Properties of reactively sputtered oxygenated cadmium sulfide (CdS:O) and their impact on CdTe solar cell performance

Oxygenated cadmium sulfide (CdS:O) is commonly used as the n-type window layer in high-performance CdTe heterojunction solar cells. This layer is deposited by reactive sputtering, but the optimal amount of oxygen in the sputtering ambient is highly dependent on the specific system and process employed. In this work, the intrinsic properties of CdS:O were measured as a function of the oxygen content (0%–10%) in the sputtering ambient and correlated to device performance with the goal of better defining optimal CdS:O properties for CdTe solar cells. Optimal performance was found using CdS:O films that contained ∼40 at. % oxygen as measured by Rutherford backscattering spectrometry. X-ray photoelectron spectroscopy confirmed these results and showed that oxygen is incorporated primarily as oxygenated sulfur compounds (SO{sub x}). Device efficiency improved from 10.5% using CdS to >14% with CdS:O due largely to increases in short-circuit current density as well as a modest improvement in open-circuit voltage. The transparency of the CdS:O films was well correlated with observed improvements in blue quantum efficiency with increasing oxygen content. The optical bandgap of as-deposited CdS:O was identified as a simple metric for process optimization and transfer, with 2.8 eV being ideal for the device architecture employed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Enhanced Sb 2 Se 3 solar cell performance through theory-guided defect control: Enhanced Sb 2 Se 3 solar cell performance

Defects present in the absorber layer largely dictate photovoltaic device performance. Recently, a binary photovoltaic material, Sb 2 Se 3 , has drawn much attention due to its low-cost and nontoxic constituents and rapid performance promotion. So far, however, the intrinsic defects of Sb 2 Se 3 remain elusive. Here in this work, through a combined theoretical and experimental investigation, we revealed that shallow acceptors, SeSb antisites, are the dominant defects in Sb 2 Se 3 produced in an Se-rich environment, where deep donors, SbSe and VSe, dominate in Sb 2 Se 3 produced in an Se-poor environment. We further constructed a superstrate CdS/Sb 2 Se 3 thin-film solar cell achieving 5.76% efficiency through in situ Se compensation during Sb 2 Se 3 evaporation and through careful optimization of absorber layer thickness. In conclusion, the understanding of intrinsic defects in Sb 2 Se 3 film and the demonstrated success of in situ Se compensation strategy pave the way for further efficiency improvement of this very promising photovoltaic technology.

14 SOLAR ENERGY↗

Defects in Epitaxial Lift-Off Thin Si Films/Wafers and Their Influence on the Solar Cell Performance

In this paper, we will describe the nature of defects and impurities in thick epitaxial-Si layers and their influence on the cell efficiency. These wafers have very low average dislocation density. Stacking faults (SFs) are the main defect in epi layers. They can occur in many configurations - be isolated, intersecting, and nested. When nested, they can be accompanied by formation of coherent twins resulting in dendritic growth, with pyramids protruding out of the wafer surface. Such pyramids create large local stresses and punch out dislocations. The main mechanism of dislocation formation is through pyramids. Stacking faults degrade solar cell performance. Analyses of the solar cells have revealed that the nested SFs have a controlling effect on the solar cell performance. A well-controlled growth can minimize defect generation and produce wafers that can yield cell efficiencies close to 20%.

14 SOLAR ENERGY↗

Influence of Different Light Sources, Light Intensities, and Water Flow Lens (WFL) System on Dye-Sensitized Solar Cell Performances

Recently, dye-sensitized solar cells demonstrated a superior performance under ambient light conditions. In this study, the influence on dye-sensitized solar cell performances was investigated under different light sources, light intensity, spectra, and water flow lens (WFL) system. Three types of light sources (xenon, halogen, and tungsten) with various spectral distributions (spectra) were used. Dyes-sensitized solar cells with varied sensitizers and co-sensitizers were tested depending on the light sources. Higher efficiency was obtained under irradiance of tungsten and halogen lamp in comparison to the xenon lamp, specifically at lower light intensities. Additionally, a new way of spectral adjustment was demonstrated. The use of a WFL system changes the distribution of spectra and remarkably influence for better performances of solar cells and efficiency values up to 30%. The results revealed that at lower light intensity, the influence of spectra was dominant and by changing spectral distribution various values of efficiency can be obtained. Also, a great influence on solar cells characteristics had a light source used for measurements. IEEE.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Amorphous/crystalline silicon interface passivation: Ambient-temperature dependence and implications for solar cell performance

Silicon heterojunction (SHJ) solar cells feature amorphous silicon passivation films, which enable very high voltages. We report how such passivation increases with operating temperature for amorphous silicon stacks involving doped layers and decreases for intrinsic-layer-only passivation. We discuss the implications of this phenomenon on the solar cell's temperature coefficient, which represents an important figure-of-merit for the energy yield of devices deployed in the field. We show evidence that both open-circuit voltage (Voc) and fill factor (FF) are affected by these variations in passivation and quantify these temperature-mediated effects, compared with those expected from standard diode equations. We confirm that devices with high Voc values at 25°C show better high-temperature performance. Thus, we also argue that the precise device architecture, such as the presence of charge-transport barriers, may affect the temperature-dependent device performance as well.

14 SOLAR ENERGY↗