Search NASA⌕ Search

SEARCH · Search NASA

Results for “solar reference cells”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

18 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Equating Reference Cell and Broadband Pyranometer Data

An adjustment algorithm has been developed for broadband Class-A pyranometers, to modify the pyranometer data such that it more closely matches that of silicon-based reference cells. The adjustment algorithm uses modeled clear-sky spectral data as one of its inputs. The adjustment also uses a reference cell angle of incidence modifier. A comparison between the pyranometer and the reference cells is performed with and without the adjustment applied. The adjustment aligns the pyranometer and reference cell data to within +-2 % under clear skies when the zenith angle is less than 70 degrees .

incident angle modifier↗
DOE OSTI2025

Photovoltaic Mini-Module Soiling Stations: Cooperative Research and Development (Final Report)

Photovoltaic (PV) panels can become soiled due to a variety of environmental factors. This soiling reduces the amount of light reaching the cells and thus their energy output. The ratio of actual output of the soiled device that of a clean device is known as the soiling ratio. The daily change in soiling ratio is known as the soiling rate. To study soiling for different glass coatings. Two soiling stations were fabricated. The stations were designed to monitor the short-circuit current of PV cells encapsulated with glass featuring different coatings and measure the daily soiling ratio with a pair of reference cells, one of which is automatically brushed daily. This work meets the need to understand how the glass coatings perform in additional environments. The stations are designed to quantify both the soiling ratio (the ratio between actual/expected photovoltaic panel power output) as well as differences in anti-soiling performance of different glass coatings. The design of the dirty/clean reference cell system is described by Toth et al. The soiling ratio is calculated by calculating the average irradiance measured within one hour of solar noon by each of the reference cells and then taking the ratio of these daily near-noon averages. The soiling ratio time series for the station deployed in Georgia is shown in Figure 1. This figure shows that the soiling ratio at the site has not yet fallen below 0.99, indicating that peak daily soiling losses have been below 1%. The site was chosen because it is thought to be affected by pollen soiling. With continued monitoring over the course of at least a full year, we expect to be able to observe and quantify pollen soiling events.

14 SOLAR ENERGY↗
DOE OSTI2025

PV Reference Cells for Outdoor Use: Stability Over Four Years of Deployment

Photovoltaic (PV) reference cells are frequently used to evaluate the performance of PV power plants. They provide a measure of irradiance that strongly correlates with the electrical output of PV modules, which makes them very useful for detecting short-term anomalies or long-term degradation in PV power plant output. One very important quality is long-term stability. This report presents observations about the stability of a set of 22 commercial reference cells that have been in continuous operation for a period of four years at the Solar Radiation Research Laboratory (SRRL) site at the National Renewable Energy Laboratory (NREL). The 22 reference cells at the SRRL represent 10 different models from 6 manufacturers.

14 SOLAR ENERGY↗
DOE OSTI2025

Scintillator based nuclear photovoltaic batteries for power generation at microwatts level

A nuclear photovoltaic battery uses scintillator to convert radiation into visible light, which is then collected by a photovoltaic (PV) cell to generate electricity. If the radiation is gamma-rays emitted from external sources, the battery may also be referred as gammavoltaic battery. In this study, a polycrystalline CdTe solar cell was optically coupled with a 2.0 cm × 2.0 cm × 1.0 cm Gadolinium Aluminum Gallium Garnet (GAGG) scintillator, and the resulting device was tested using intense gamma radiation fields from a Cs-137 (1.5 kRad/h) and a Co-60 (10 kRad/h) irradiator. Measurements with Cs-137 provided a maximum power output (P max ) of ~288 nW, with a short-circuit current density (J sc ) of ~1.22 μA/cm 2 and an open-circuit voltage (V oc ) of ~0.34 V. In contrast, Co-60 irradiator gave a P max of 1.5 μW, with a J sc of ~4.73 μA/cm 2 and a V oc of ~0.38 V. The CdTe was also paired with a Lutetium-Yttrium Oxyorthosilicate (LYSO) crystal and tested with the Cs-137 source. The experiment presents a scalable option to reach to higher power outputs by harvesting gamma radiation fields in many cases where high radiation field demands heavy shielding and is often regarded as unwanted waste.

25 ENERGY STORAGE↗
DOE OSTI2025

Carboxyl-functionalized perovskite enables ALD growth of a compact and uniform ion migration barrier

Mixed-halide wide-band-gap perovskites are critical components of highly efficient tandem cells, but their operating stability is limited by halide migration. Metal oxides deposited via atomic layer deposition (ALD) have been shown to block halide migration; however, previously pursued methods result in inhomogeneous nucleation and growth. We hypothesized that functionalizing the perovskite surface with ALD-active carboxyl groups could promote nucleation and enable higher-temperature metal oxide growth. We find that 5-ammonium valeric acid iodide (5-AVAI) facilitates the formation of a compact and uniform aluminum oxide (Al 2 O 3 ) layer and allows growth at 100°C compared with the previous limit of 75°C. We demonstrate that halide migration into the C 60 electron transport layer is reduced by a factor of 10 compared with the reference case. Finally, Al 2 O 3 -capped perovskite solar cells with a band gap of 1.78 eV retain 90% of their initial power conversion efficiency after 1,000 h of continuous operation under 1-sun illumination at 55°C.

Al2O3↗
DOE OSTI2025

Combining Organic Cations of Different Sizes Grants Improved Control over Perovskitoid Dimensionality and Bandgap

Because mixed-halide wide-bandgap (1.6-2.0 eV) perovskite solar cells suffer from operating instability related to light-induced halide segregation, it is of interest to study alternative means of bandgap widening. Perovskitoids combine wide bandgaps and structural stability resulting from face- or edge-sharing octahedral connections in their crystal structures. Unfortunately, there existed no prior reports of three-dimensional (3D) perovskitoids having direct bandgaps with optical absorption edges less than 2.2 eV. As the most significant predictor of perovskitoid bandgaps is the fraction of corner-sharing in their crystal structures, we hypothesized that increasing the amount of corner-sharing would access lower bandgaps than previously reported. Here, we accomplished this by mixing a spacer cation within the size range for 3D perovskitoid formation with a smaller perovskite-forming cation. We explored three spacer cations of different sizes: ethylammonium (EA), cyclopropylammonium (c-C3A), and cyclobutylammonium (c-C4A), combining these with methylammonium (MA), and found that the middle cation, c-C3A, pairs with MA to form a 3D perovskitoid with the formula (c-C3A) 3 (MA) 3 Pb 5 I 16 and a direct bandgap with an optical absorption edge at 2.0 eV. Solution-processed films of this perovskitoid showed improved light stability over mixed-halide perovskites, and solar cells based on these films exhibit increased maximum power point operating stability compared to reference mixed-halide devices.

Gilley, Isaiah W. [Northwestern University, Evanst↗
DOE OSTI2024

Bifacial Vertical Testbed and Ground Irradiance Data in Golden, Colorado

This data was collected for Tonita et al., “Vertical bifacial photovoltaic system model validation: study with field data, various orientations, and latitudes,” for validation of optical models for vertically-oriented photovoltaics under high albedo. Ground irradiance data for vertical PV arrays modeling in agrivoltaics is also provided. The dataset is provided for further use or study as open source. For any questions on the dataset, email silvana.ovaitt@nlr.gov.

14 SOLAR ENERGY↗
DOE OSTI2025

High‐Speed Slot‐Die Coating with Donor‐Priority Rapid Aggregation Kinetics for Improved Morphology and Efficiency in Ecofriendly Organic Solar Cells

Abstract Solution‐processable organic solar cells (OSCs) represent a promising renewable photovoltaic technology with significant potential for eco‐compatible production. While high power conversion efficiencies (PCEs) have been achieved in OSCs, scaling this technology for high‐throughput manufacturing remains challenging. Key reason lies in the lack of efficient control strategies for the complex and long‐duration morphology evolution during high‐speed coating process with ecofriendly solvents. Here, a donor‐priority rapid aggregation process (DP‐RAP) scheme is proposed to solve this issue by adjusting the aggregation kinetics of donor and acceptor components. DP‐RAP enables blends with a nanoscale fiber network structure and favorable crystallinity, which contributes to balanced carrier transport and reduced recombination losses. As a result, the PCE is improved from 14.3% (reference) to 17.4% (DP‐RAP) for ultra‐high speed coated PM6:BTP‐eC9 devices in atmosphere, which is one of the highest values for non‐halogenated solvent‐processed solar cells at coating speeds of 500 mm s −1 . Moreover, the DP‐RAP based devices remain a stable PCE of approximately 17.4% across a broad range of coating speeds (20–500 mm s −1 ), illustrating its tolerance to the varied manufacturing conditions. This work highlights a promising avenue for the high‐speed, ecofriendly production of efficient OSCs, pushing the boundaries of practical manufacturing in renewable energy technologies.

Chemistry↗
DOE OSTI2026

Public Reference Data for Megawatt-Scale Hydrogen Electrolysis - NLR Historical Solar PV

The U.S. Department of Energy and National Laboratory of the Rockies (NLR) demonstrate hydrogen electrolysis from variable sources, hydrogen compression and storage, and hydrogen fuel cell power production using megawatt-scale equipment at NLR’s Flatirons Campus as part of the Advanced Research on Integrated Energy Systems (ARIES) research platform. This dataset represents part of that effort and is intended for academic, national laboratory, industrial, and other stakeholders to plan, design, and validate models of megawatt-scale hydrogen technologies and diverse energy infrastructure nationwide. These data provide a baseline for how existing hydrogen electrolysis technologies perform when coupled with various energy technologies. Future datasets will demonstrate how existing hydrogen fuel cell technologies can provide controllable, dispatchable, and variable power output for artificial intelligence data centers and other variable loads. This dataset entry describes the behavior of a 1.25-MW proton exchange membrane MC250 electrolyzer system, manufactured by Nel Hydrogen , [1] when fed historical data generated by the 430-kW, fixed-axis solar photovoltaic (PV) array located at NLR’s Flatirons Campus. (While the electrolyzer balance of plant supports up to 2.5 MW of electrolysis, NLR only has a single 1.25-MW electrolysis stack.) Solar PV power output data for the 2020 calendar year were categorized on a daily basis by total energy generation and standard deviation. Each day was then ranked by these metrics, and the 25th, 50th, and 100th percentiles were selected. The 75th percentile day did not exhibit sufficient variability to make for a valuable experiment. A similar process was used for the related historical wind dataset . [2] The historical days in 2020 that represented these percentiles are Dec. 19, March 29, and May 4, respectively. The entire solar day’s power profile was then fed through the MC250 electrolyzer. Due to its length, the 100th percentile day experiment was split into two parts, and the final 3 hours of the solar day were not captured. These final 3 hours contained no spikes or dips of interest and simply represented a slow decay of input solar power. Also, a single timestamp (13:13:47 on Jan. 14, 2026) was lost in the hydrogen system supervisory control and data acquisition. Finally, during the 25th percentile experiment (solar day Dec. 19, 2020) data recording was lost from 11:00:13 to 11:14:45. The roughly 15 minutes of the solar profile were rerun at the end of the experiment and spliced into this time slot during post-processing. The electrolysis system controls hydrogen production by varying direct current applied to the stack, from a maximum of 3,000 A to a minimum safe operation of 300 A, or 10%. Because the current–voltage characteristic changes as the stack ages and efficiency degrades, the actual minimum safe operating power changes over time. The historical solar profiles were translated from power (kilowatts) to current (amperes) using a curve fit with calibration data and sent to the electrolyzer power supply at 1-Hz frequency. For more details on the statistical analysis process, see the slide deck “Public Reference Data for Megawatt-Scale Hydrogen Electrolysis: NLR Historical Solar PV Analysis and Profile Generation” accessible with this data entry. These datasets report relevant hydrogen balance-of-plant and system data, all captured at 1 Hz, including hydrogen mass production measured with an Emerson Coriolis flow meter. Each .zip file represents a single solar PV electrolysis experiment and is formatted as: {technology}_{percentile}_{scaling factor} For instance, “solarPV-430kW_25_2x.zip” reports the experiment using the 25th percentile solar data from the historical 2020 solar PV dataset, scaled to 200%. Scaling factors were applied to the generated solar PV power output files to more closely match the 1.25-MW capacity of the electrolyzer. Each .zip folder contains the following files: A .csv file containing raw data. An .xlsx file explaining all the fields in the raw data. A .png plot showing the time series of hydrogen production, electrolysis power consumption, and solar power input. A PDF file detailing the historical solar data statistical analysis used to generate the solar profile. An experiment labeled “characterization_200.zip” demonstrates the MC250 electrolyzer steady-state response with 30-minute load steps for a total duration of 5 hours. Finally, a .csv file is provided with all experiments combined into one dataset labeled "combined_solarPV_experiments.csv". [1] nelhydrogen.com/product/mc-series-electrolyser . [2] data.nlr.gov/submissions/316 .

08 HYDROGEN↗
DOE OSTI2025

Significant Efficiency Enhancements in Non‐Y Series Acceptors by the Addition of Outer Side Chains

Abstract Most current highly efficient organic solar cells utilize small molecules like Y6 and its derivatives as electron acceptors in the photoactive layer. In this work, a small molecule acceptor, SC8‐IT4F, is developed through outer side chain engineering on the terminal thiophene of a conjugated 6,12‐dihydro‐dithienoindeno[2,3‐d:2′,3′‐d′]‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene (IDTT) central core. Compared to the reference molecule C8‐IT4F, which lacks outer side chains, SC8‐IT4F displays notable differences in molecule geometry (as shown by simulations), thermal behavior, single‐crystal packing, and film morphology. Blend films of SC8‐IT4F and the polymer donor PM6 exhibit larger carrier mobilities, longer carrier lifetimes, and reduced recombination compared to C8‐IT4F, resulting in improved device performance. Binary photovoltaic devices based on the PM6:SC8‐IT4F films reveal an optimal efficiency over 15%, which is one of the best values for non‐Y type small molecule acceptors (SMAs). The resultant devices also show better thermal and operational stability than the control PM6:L8‐BO devices. SC8‐IT4F and its blend exhibit a higher relative degree of crystallinity and π coherence length, compared to C8‐IT4F samples, beneficial for charge transport and device performance. The results indicate that outer side chain engineering on existing small electron acceptors can be a promising molecular design strategy for further pursuing high‐performance organic solar cells.

He, Qiao [Department of Chemistry and Centre for P↗
DOE OSTI2026

Africa Battery Energy Storage Systems (BESS) Capacity Building Li-Ion Battery Degradation and Performance [Slides]

This presentation is intended for power system engineers, operators, and planners who work on isolated power systems that have (or may soon have) high levels of power generation coming from wind turbines, solar farms, and battery energy storage, which are collectively referred to as inverter-based resources. It describes the basics of lithium-ion battery energy storage systems and lithium-ion battery degradation. Battery degradation at the cell-level is explained, and then the structure and degradation of battery energy storage systems is also explained. This is intended to help power system engineers, operators, and planners to understand and effectively utilize battery energy storage systems.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2024

Safety Review of the Hydrogen Components of a Reference Design of the Wind-H2-Green Steel/Ammonia Project

The Department of Energy Hydrogen Fuel Cell Technology Office and Wind Energy Technologies Office’s Wind-H2-Green Steel/Ammonia project is an initiative to demonstrate the feasibility and efficacy of GW-scale integrated energy systems. The team designed reference facilities that utilize wind- and solar-produced hydrogen for industrial steel and ammonia production. This novel concept warranted review of safety codes and standards as they apply to the designs and the identification of codes and standards as they apply to the designs and the identification of codes and standards gaps. This report reviews hydrogen production and storage codes and standards using reference design specifications from a Minnesota steel plant. Requirements, recommendations, and exclusions for the system were identified. Observed gaps included non-specific salt cavern storage requirements, electrolyzer capacity beyond regulated ranges, and lack of requirements for iron reduction via hydrogen. This report will aide future project design efforts and may provide a basis for safety reviews in new designs for industrial facilities with hydrogen production integration.

08 HYDROGEN↗
DOE OSTI2024

Safety Review of the Hydrogen Components of a Reference Design of the Wind-H2-Green Steel/Ammonia Project

The Department of Energy Hydrogen Fuel Cell Technology Office and Wind Energy Technologies Office's Wind-H2-Green Steel/Ammonia project is an initiative to demonstrate the feasibility and efficacy of GW-scale integrated energy systems. The team designed reference facilities that utilize wind- and solar-produced hydrogen for industrial steel and ammonia production. This novel concept warranted review of safety codes and standards as they apply to the designs and the identification of codes and standards gaps. This report reviews hydrogen production and storage codes and standards using reference design specifications from a Minnesota steel plant. Requirements, recommendations, and exclusions for the system were identified. Observed gaps included non-specific salt cavern storage requirements, electrolyzer capacity beyond regulated ranges, and lack of requirements for iron reduction via hydrogen. This report will aide future project design efforts and may provide a basis for safety reviews in new designs for industrial facilities with hydrogen production integration.

08 HYDROGEN↗
DOE OSTI2025

Closing the Accuracy Gap in Tandem Photovoltaic Testing: An Accessible and Efficient Spectral Tuning Method Using LED-Based Simulators for Research Laboratories and Industry

Accurate performance calibration of multijunction (MJ) solar cells is critical for advancing this technology toward large-scale terrestrial application, yet existing testing methods developed by photovoltaics calibration laboratories remain prohibitively complex and resource intensive for most research laboratories. Current approaches rely on expensive multisource simulators and/or intricate spectral tuning algorithms, limiting accessibility and hindering standardized comparisons of emerging MJ technologies such as perovskite-based tandems. This paper introduces a streamlined spectral irradiance adjustment method for light-emitting diode (LED)-based solar simulators, which are increasingly adopted in the photovoltaics community due to their versatility and cost-effectiveness. The method we present bins LED channels into groups based on the number of junctions of the MJ photovoltaic device under test (DUT) and their corresponding band gaps and incorporates an automated tuning algorithm that eliminates the need to adjust each channel’s irradiance individually. This tuning algorithm requires the relative spectral responsivities of both the DUT and a broadband reference cell, as well as a calibrated spectroradiometer. Measurement validation across various MJ devices, including III-V and perovskite/silicon tandems, demonstrates excellent agreement within 1% with well-established xenon-tungsten multisource simulators and associated tuning algorithms. By enabling precise spectral tuning with readily available equipment and a simple tuning algorithm, our approach bridges the measurement accuracy gap between research laboratories and accredited testing facilities, fostering more reliable device comparisons and accelerating the translation of MJ technologies into real-world energy systems.

14 SOLAR ENERGY↗
DOE OSTI2024

Machine learning enhanced characterization and optimization of photonic cured MAPbI 3 for efficient perovskite solar cells

Photonic curing (PC) can facilitate high-speed perovskite solar cell (PSC) manufacturing because it uses high-intensity light pulses to crystallize perovskite films in milliseconds. However, optimizing PC conditions is challenging due to its many variables, and using power conversion efficiency (PCE) as the optimization metric is both time-consuming and labor-intensive. This work presents a machine learning (ML) approach to optimize PC conditions for fabricating methylammonium lead iodide (MAPbI 3 ) films by quantitatively comparing their ultraviolet-visible (UV-vis) absorbance spectra to thermal annealed (TA) films using four similarity metrics. We perform Bayesian optimization coupled with Gaussian process regression (BO-GP) to minimize the similarity metrics. Refining PC conditions using active learning based on BO-GP models, we achieve a PC MAPbI3 film with an absorbance spectrum closely matching a TA reference film, which is further verified by its crystalline and morphological properties. Thus, we demonstrate that the UV-vis absorption spectrum can accurately proxy film quality. Additionally, we use an AI-based segmentation model for a more efficient grain size analysis. However, when we use the optimized PC condition to fabricate PSCs, we find that interaction between MAPbI 3 and the hole transport layer (HTL) during PC critically degrades the PSC performance. By adding a buffer layer between the HTL and MAPbI 3 , the optimized PC PSCs produce a champion PCE of 11.8%, comparable to the TA reference of 11.7%. Using UV-vis similarity metrics instead of device PCE as the objective in our BO-GP method accelerates the optimization of PC processing conditions for MAPbI 3 films.

14 SOLAR ENERGY↗
DOE OSTI2026

Structure of Layers Formed by [2-(3,6-Disubstituted-9 H -carbazol-9-yl)ethyl]phosphonic Acids on Metal Oxides

[2-(9 H -Carbazol-9-yl)ethyl]phosphonic acid (2PACz) and its derivatives are being used extensively as hole-transport layers in organic and perovskite solar cells due to their ability to modify electrode work function, surface wettability, and in some cases, to improve active-layer adhesion, while minimizing interfacial energy losses. The orientation and coverage of surface modifiers significantly impact these functional properties; however, the detailed structure and packing in these overlayers are challenging to investigate, leading to a lack of understanding of how this structure and packing influence performance and limiting the ability to rationally design molecular modifiers. Here, we investigate monolayers of 2-(9 H -carbazol-9-yl)ethyl phosphonic acid derivatives (from here on referred to as X-2PACz) on indium tin oxide (ITO) and alpha phase aluminum oxide (α-Al 2 O 3 ) using a combination of X-ray photoelectron spectroscopy (XPS), near-edge X-ray absorption fine structure (NEXAFS) spectroscopy, and X-ray reflectivity (XRR). By correlating elemental ratios, molecular orientation, and electron density profiles, we directly quantify surface coverage, layer thickness, and molecular tilt across a series of chemically related monolayers. We find that 2PACz and the X-2PACz derivatives form dense monolayers on α-Al 2 O 3 and ITO, with similar surface coverages on either substrate that are inversely proportional to molecular steric bulk. These surface coverage results indicate that X-2PACz is sterically limited in its monolayer surface packing density, as opposed to site limited. Despite surface packing density differences between molecules, the NEXAFS data show a constant average molecular orientation of 61° to 65° between the plane of the carbazole and the substrate for all the molecules on both substrates. These results increase our general understanding of 2PACz derivatives as they become increasingly useful in high performance solar cells.

NEXAFS↗
DOE OSTI2025

Dielectric constant engineering of nonfullerene acceptors enables a record fill factor of 83.58% and a high efficiency of 20.80% in organic solar cells

Organic solar cells (OSCs) have achieved power conversion efficiencies (PCEs) surpassing 20%, but their development remains hindered by the inherently low dielectric constant (εr) of organic semiconductors, which limits charge transport and contributes to serious recombination losses. Herein, we present a comprehensive strategy to overcome the challenge by engineering the dielectric properties of nonfullerene acceptors (NFAs). Two Y-series NFAs of BTP-N3F and BTP-C3F have been synthesized featuring trifluoromethyl (CF 3 ) end-capped alkyl side chains. This molecular design significantly enhances the dipole moment and ε r (up to ∼5.9) when compared to the reference acceptor Y6 (∼3), reducing the exciton binding energy (E b ) and improving charge transport. Furthermore, the incorporation of a high-εr polymer additive, poly(pentafluorostyrene) (PPFS), synergistically improves the active layer morphology and dielectric properties, enabling efficient charge extraction and reduced recombination losses. Devices based on the optimized D18-Cl/BTP-C3F system have achieved a record-high fill factor (FF) of 83.58% and an impressive PCE of 20.80%, setting a new benchmark for OSCs. Finally, our results underscore the pivotal role of ε r in enhancing device performance and establish a versatile pathway for advancing OSC efficiency and stability through molecular and morphological optimization.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Monthly averages of ED2 model simulations initialized with airborne lidar structure, Jan 1981-Dec 2018, Brazilian Amazon

Deforestation and forest degradation (selective logging, fires, fragmentation) have impacted nearly 40% of the original extent of the Brazilian Amazon, and have markedly impacted forest structure across the region. To date, few studies analysed how shifts in forest structure from degradation influence the forest sensitivity to climate extremes, because of the complex interactions between forest structure and micro-environmental conditions. To address this knowledge gap, we carried out a series of simulations across the Brazilian Amazon using the Ecosystem Demography Model (ED2), using observed forest structure derived from 541 airborne lidar transects (375 ha each) and two scenarios representing forest recovery and expansion of degradation to investigate how shifts in forest structure impact ecosystem function under near-average and extreme climate conditions, as part of the manuscript Longo et al 2025 "Degradation and Deforestation Increase the Sensitivity of the Amazon Forest to Climate Extremes". This dataset provides the output results from the ED2 model simulations for the three simulations at monthly time scales, in NetCDF format. For all simulations, we used bias-corrected hourly reanalyses (WFDE5) for most meteorological drivers, except for precipitation, which was obtained from CHIRPS. The meteorological drivers used in the study span 38 years (Jan 1981–Dec 2018). The output results correspond to the last 38 years of simulation (one full cycle of meteorological drivers), in which ED2 simulations used static stand structure (i.e., the forest structure was held constant). The following files are provided:ED2_emean_Global_R004_BrAmaz_s1c0t0l0f0.nc. This corresponds to the Control simulation. The forest structure was obtained from the airborne lidar.ED2_emean_Global_R005_BrAmaz_s1c0t1l1f0.nc. This corresponds to the Degraded simulation. The forest structure was obtained from a spin-up simulation initialized with airborne lidar and a scenario that expanded deforestation and selective logging across the Amazon.ED2_emean_Global_R006_BrAmaz_s1c0t1l0f0.nc. This corresponds to the Recovery simulation. The forest structure was obtained from a spin-up simulation initialized with airborne lidar and a scenario that completely halted deforestation and degradation, allowing degraded forests to recover for 38 years.We also provide file ED2_zones_R004_BrAmaz_s1c0t0l0f0.nc, which classifies each grid cell into zones used in the reference manuscript: 1: Southeast. 2: South. 3: West. 4: Central. 5: Northeast. 6: North. 7: Northwest". Index 0 corresponds to grid cells excluded from sub-region analyses because they were dominated by flooded forests, deforestation, and naturally non-forest vegetation.

54 ENVIRONMENTAL SCIENCES↗