Search NASA⌕ Search

SEARCH · Search NASA

Results for “solid state lighting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Green Light Emitting Diodes for the Ultimate Solid-state Lighting

Light-emitting diodes (LEDs), in particular InGaN-based LED devices, have achieved remarkable success in solid-state lighting, contributing to 25% of energy savings already. However, more than two thirds of the electricity is still lost as heat in current white LEDs today. Furthermore, expected population growth and increasing demand for lighting necessitate a more efficient approach, which can only be realized by solving the issue of the green gap (i.e., the inefficiency of the state-of-the-art green LEDs). This green gap is a fundamentally limiting issue in conventional hexagonal nitride LEDs, leading to 19% wall-plug efficiency (WPE) at 100 A/cm 2 , while the department of energy goal is 30% (in 2025) and 55% (in 2035).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Adaptive Time-Division Multiplexing Driving System for Solid State Lighting with Multiple Tunable Channels

Next generation solid state lighting enables unlimited control of light and serve much broader functions beyond the basic lighting for illuminance. The emerging lighting for productivity, well-being, healthcare, and growth have revolutionized the scope of lighting. To empower this unlimited controllability, a multi-channel tunable power-electronics driver is essential but has not been satisfactorily addressed so far. Existing solutions are lossy, large, and expensive, due to introduction of additional buck power conversion stages. This paper proposes a time-division multiplexing (TDM) LED driving system which eliminates those buck stages. The proposed design can directly pair with off-the-shelf pulse width modulated (PWM) controllers and since it inherits entire feature sets, it can achieve low loss at standby and at dimmed condition. The simple analog implementation avoids usage of expensive DSPs/MCU. GaN’s high switching frequency capability can push up the multiplexing frequency so a GaN-based flyback was built and proved the concept.

Xue, Lincoln↗
DOE OSTI2023

Stable Cadmium-Free Quantum Dot Optical Down-Converters for Solid State Lighting

Quantum dots (QDs) have been used in commercial solid-state lighting (SSL) applications to improve the energy efficiency of light generation at warm color temperatures. By increasing the amount of QDs used in each product, further energy savings are possible; however, traditional QDs contain cadmium, which has regulatory limits on its concentration in consumer products. As described within this final technical report, we have established that heavy-metal free QDs made from indium phosphide (InP) exhibit highly efficient emission at the temperatures and fluxes relevant to SSL. However, the maintenance of this emission is compromised during long term operation due to QD oxidation. We have identified multiple methods to slow the oxidation rate, which has improved the operational stability of these materials more than 200 times longer than at the project start. Beyond these improvements, heavy-metal free QDs require a further hundred-fold increase in stability to enable use in mid-power SSL and a ten-fold increase in stability to enable use in diffuse SSL applications. The outcomes of this project demonstrate feasibility for the use of heavy-metal free QDs in commercial SSL applications with potential use in diffuse SSL applications in the near term (1-2 years) pending market need.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Environmentally Robust Quantum Dot Down Converters for Highly Efficient Solid State Lighting

This project contributes fundamental understanding of the chemical synthesis of cadmium free quantum dots (QDs) designed for solid state lighting (SSL). Methods to incorporate gallium into quantum dot architectures were explored, which led to more stable and brighter solid state lighting devices. These findings will help advance the incorporation of quantum dots in highly energy efficient lighting devices with a warm color spectrum. Such Cd-free lighting devices can greatly accelerate the adoption of high efficiency, warm spectrum lighting in buildings. The project targeted InP/GaP/ZnS colloidal quantum dots that more effectively absorb the blue light produced by light emitting diode packages and emit monochromatic red light with near perfect efficiency. While significant improvements in the QD absorptivity were demonstrated, the absorbance increase achieved was 3x rather than the targeted 10x increase. Similarly, the luminescence from these QDs achieved about half of the target photoluminescence quantum yield (PLQY) and twice the desired spectral width, a measure of the color purity of their luminescence. While the target characteristics and some of the year 2/2 milestones were not met, the new QD architectures did lead to greater stability on SSL packages, a sign of the long term promise of the technology.

36 MATERIALS SCIENCE↗
DOE OSTI2022

2022 Solid-State Lighting R&D Opportunities

This is an updated edition that examines critical opportunities to positively impact energy savings, greenhouse gas emissions, human well-being, and the economy through Solid-State Lighting (SSL) R&D. The document summarizes stakeholder input from DOE-hosted roundtable meetings, workshops, a Request for Information, and other sources.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

Efficient green and yellow light-emitting diodes (LEDs) for solid-state lighting applications

In this project, Lumileds, the University of Michigan, the University of New Mexico, Sandia National Laboratories, and Ohio State University conducted a collaborative and comprehensive research effort to investigate the most promising approaches to improve green and yellow InGaN LEDs. Advanced LED characterization methods and predictive model calculations were applied to design optimization experiments more effectively and accelerate the pace of improvements.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

Solid-State Lighting Using Side-by-Side White Phosphorescent Organic Light-Emitting Diodes

White organic light-emitting diodes (WOLEDs) have become increasingly popular for use in solid-state illumination, where diffuse, large area light sources that achieve a high color rendering index and luminous power efficiency are desirable. Color-tunable emission, where the light source combines emission from multiple, separately addressed color elements, is conveniently provided by WOLEDs for the purpose of adapting the lighting source to a particular illumination requirement. In this work, we demonstrate a method for side-by-side positioning of monochromatic blue and yellow phosphorescent OLED stripes that are combined to create tunable white light, using a high resolution mechanical peel-off patterning method. We achieve a peak luminous power efficiency of 17.1 ± 0.3 lm W –1 and an external quantum efficiency of 11.8 ± 0.2% and demonstrate color tunability of the 1960 Commission Internationale d’Eclairage chromaticity coordinates from (u,v) = (0.33,0.36) to (0.12,0.32). This corresponds to a tuning rnge of the color rendering index from 74 ± 1 to 86 ± 1 and the correlated color temperature from 2000 to 8000 ± 500 K. Here, due to the nondestructive nature of the peel-off technique, patterned devices exhibit a lifetime comparable to conventional, shadow mask-patterned devices.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

Comparing the influence of cation order and composition in simulated Zn(Sn, Ge)N 2 on structure, elastic moduli, and polarization for solid state lighting

Alloying and site ordering play complementary roles in dictating a material’s properties. However, deconvolving the impacts of these separate phenomena can be challenging. In this work, we simulate structures of Zn(Sn,Ge)N 2 with varied Sn content and site ordering to determine the impacts of order and composition on structural and electronic properties. We assess the formation enthalpy, lattice parameters, elastic constants, spontaneous polarization, and piezoelectric coefficients. In mostly disordered structures (order parameters ranging from 0.2 to 0.4), the formation enthalpy exhibits local extrema as a function of the order parameter, deviating from the more linear trends seen in both fully disordered and fully ordered systems. This anomalous deviation from the otherwise linear trend in formation enthalpy with order manifests in each of the other properties calculated. This range of order parameters of interest may be caused by a transition in the ordering of the quaternary material similar to phase changes seen in ternary compounds but stretched over a region inclduing 20% of the order parameter range. Most parameters calculated are more sensitive to order than to composition in the limited composition range tested; however, the lattice parameter c, piezoelectric coefficient e 33 , and elastic moduli C 12 , C 13 , and C 23 are more sensitive to composition. Of the properties compared, the piezoelectric coefficients are influenced most significantly by changes in both the composition and order parameter. Lattice parameters undergo the smallest changes with order and composition, but these small differences appear to impart large trends in the other properties. Better understanding the effects of disorder and group IV alloying in Zn(Sn,Ge)N 2 allows for more accurate modeling of characteristics of this material system for solid state lighting and other applications.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Impact of Solid State Roadway Lighting on Melatonin in Humans

Introduction: In 2009, the World Health Organization identified vehicle crashes, both injury-related and fatal, as a public health hazard. Roadway lighting has long been used to reduce crashes and improve the safety of all road users. Ocular light exposure at night can suppress melatonin levels in humans. At sufficient light levels, all visible light wavelengths can elicit this response, but melatonin suppression is maximally sensitive to visible short wavelength light. With the conversion of roadway lighting to solid state sources that have a greater short wavelength spectrum than traditional sources, there is a potential negative health impact through suppressed melatonin levels to roadway users and those living close to the roadway. This paper presents data on the impact of outdoor roadway lighting on salivary melatonin in three cohorts of participants: drivers, pedestrians, and those experiencing light trespass in their homes. Methods: In an outdoor naturalistic roadway environment, healthy participants (N = 29) each being assigned to a cohort of either pedestrian, driver, or light trespass experiment, were exposed to five different solid state light sources with differing spectral emissions and one no lighting condition. Salivary melatonin measurements were made under an average roadway luminance of 1.0 cd/m2 (IES RP-18 Roadway Lighting Requirements for expressway roads) with a corneal melanopic Equivalent Daylight Illuminances (EDI) ranging from 0.22 to 0.86 lux. Results: The results indicate that compared to the no roadway lighting condition, the roadway light source spectral content did not significantly impact salivary melatonin levels in the participants in any of the cohorts. Conclusions: These data show that recommended levels of street lighting for expressway roads do not elicit an acute suppression of salivary melatonin and suggest that the health benefit of roadway lighting for traffic safety is not compromised by an acute effect on salivary melatonin.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2022

Evaluation of the Reliability of Passive Infrared (PIR) Occupancy Sensors for Residential Indoor Lighting

Solid-state lighting (SSL) technologies have penetrated the general illumination market in recent years, largely replacing conventional technologies such as incandescent and fluorescent lighting. Most of the initial excitement about light-emitting diode (LED) sources for SSL devices focused on their energy savings potential resulting from vast improvements in source efficiency and luminous efficacy compared with conventional illumination products. More recently, the focus has shifted toward other aspects of lighting application efficiency, namely intensity effectiveness and spectral efficiency, because of the ease of controlling both the light intensity of LEDs with drive voltage and the color properties of the LED-based illuminators. To capitalize on the energy savings of increased intensity effectiveness and spectral efficiency, a lighting control system (LCS) is often used. While the current penetration of LCSs is relatively modest, it is anticipated that lighting controls (i.e., connected lighting, controls and LED and conventional lighting) could have an installed penetration as higher as 46% by the year 2035, saving an additional 1.3 quads of energy. Despite the large energy savings that can be gained from using LCSs, standard test methods for evaluating sensors employed in LCSs and reliability data of the LCSs and their components are generally lacking. The National Electrical Manufacturers Association (NEMA) developed the only standard, NEMA WD 7-2011 (R2016), to test occupancy and motion sensor performance (herein referred to as “the NEMA protocol”). In a previous U.S. Department of Energy (DOE) effort, some concerns of the NEMA protocol were identified (e.g., strict height and weight limits on test subjects, large amounts of manual effort, sometimes inconsistent repeatability). During the current work, a consistent detection length test (DLT) and a Robotic Sensor Evaluation System (RoboSES) were developed to alleviate some of these concerns. RoboSES acts as a human surrogate by using thermal pads on a mannequin and a remote-controlled mobile base to test a sensor’s field of view (FOV). This report builds on the earlier DOE efforts to understand sensor technologies used in LCSs for general illumination. Specifically, this report describes the optimization of RoboSES, characterizes and establishes test methods to assess the reliability of multiple passive infrared (PIR) sensors, and reports the findings of robustness and reliability testing on two commercial PIR sensors intended for residential applications. The information presented in this report is gained from up to 4,000 hours (hrs) of accelerated stress tests (ASTs).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

Surface Ligand Effects on Energetics, Charge Transfer, and Stability at Interfaces Between Metal Halide Perovskites and Organic Semiconductors

Chemistry at organic-inorganic interfaces plays a major role in determining the performance of electronic and optoelectronic devices. Understanding, developing, and using surface chemistry is thus essential for creating improved and novel materials and devices. Organic metal halide perovskites (HPs) are inexpensive semiconductors that can be printed from solution to make efficient photovoltaic cells for harvesting solar energy, light emitting diodes for energy efficient solid-state lighting applications, solid-state lasers, and even spin selective devices with applications to quantum computing. To realize the potential of HPs, their surface chemistry and interfacial properties must be better understood and appropriately adjusted to meet the needs of the targeted application. For example, surface chemistry influences non-radiative recombination, which influences the efficiency of light emission and solar energy conversion, charge-carrier injection and extraction from optoelectronic devices, and material and device stability. This research project centered around determining how the surface chemistry of HP thin films and nanoparticles influences optical properties, charge transfer processes, energetics, and stability. In this project we characterized ligand binding strengths to HPs; determined how surface ligand chemistry influences photoluminescence properties, energetics, and charge transfer processes; determined that surface ligands often penetrate into HPs and uncovered methods of reducing surface ligand penetration through structural modifications; and discovered how interfacial energetics impact charge transfer processes and photovoltaic performance parameters. Overall, this research established important insights into how surface ligands interact with HPs to influence their optical properties, electronic properties, stability, and device level performance.

14 SOLAR ENERGY↗
DOE OSTI2021

Improved Light Extraction by Engineering Molecular Properties of Square Planar Phosphorescent Emissive Materials

The ultimate objective of this project was to develop a cost-effective technology which could significantly improve the light outcoupling efficiency up to 70% and higher and the key tasks were listed as follows: (i) improving light extraction efficiency through a better control of horizontally aligned emitting dipoles of square planar phosphorescent emitters; (ii) fabricating high-efficiency monochromic and amber OLED in the device settings; (iii) fabricating high-efficiency white OLED in the device settings. With both materials innovation and device structure optimization, we realized OLEDs with an EQE of 66% with a LT 95 lifetime of over 100 khrs at a brightness of 1,000 cd/m 2 . This proposed research is a high impact project which could potentially revolutionize OLED lighting technology and expedite the commercialization process of OLED technology for solid state lighting. This project outcomes contributed to meet the targeted performance of organic solid state lighting set in the DOE MYPP.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Investigating the Impacts of Outdoor Lighting (Final Report)

This report documents the research associated with the Depart of Energy supported project “Investigating the Health Impact of Outdoor Lighting.” This project was developed to consider how alternative solid state lighting options, particularly the spectral power distribution, effected the hormone melatonin which ultimately could lead to potential health issues. The project also provides an opportunity to gather other secondary data with respect to visual performance in a controlled environment. These tasks were developed to consider how alternative solid state lighting applications impacted performance. This report is a complete documentation of the tasks undertaken as part of this project. The report includes a literature review and consideration of the background data which are part of this field of study as well as a documentation of the methods developed as part of the project. The melatonin results, the primary dependent variable are included in the attached peer-review paper that has been recent published (Gibbons et al., 2022). Our discussion of these results are included in that publication. Other results from this project will be documented in one or more future publications.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Tunable broadband luminescence in lead-free hybrid copper halides

Metal halides are an important class of optoelectronic materials combining exceptional optical and electronic properties. An inherent advantage of metal halides is their solution synthesis and processability, which render them as low-cost and environmentally friendly materials for a range of applications from photovoltaics and photodetection to solid-state lighting (SSL). Here, in this study, we synthesized three previously unreported lead-free organic–inorganic hybrid copper halides: (OA) 4 CuX 5 (X = Br, I; OA + = C 8 H 17 NH 3+ , n-octylammonium cation) and (HA) 2 CuI 3 (HA + = C 6 H 13 NH 3 + , n-hexylammonium cation), all of which exhibit broadband emissions arising from self-trapped excitons (STEs). Among these compounds, (OA) 4 CuI 5 demonstrates tunable dual-band white-light emission with a high color rendering index value of 91 at room temperature. Temperature-dependent photoluminescence measurements and first-principles calculations reveal distinct behaviors between the two emission states in (OA) 4 CuI 5 . These findings highlight the potential of copper halide compounds for optoelectronic applications, particularly in the development of environmentally friendly solid-state lighting technologies.

36 MATERIALS SCIENCE↗