Search NASA⌕ Search

SEARCH · Search NASA

Results for “spark plug”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1946

Effect of Fuel Composition, Engine Operating Variables, and Spark-Plug Type and Condition on Preignition-Limited Performance of an R-2800 Cylinder

The preignition characteristics of the R-2800 cylinder, as effected by fuel consumption, engine operating variables, and spark plug type and condition, were evaluated. The effects on preignition-limited performance of various percentages of aromatics (benzene, toluene, cumene, xylene) in a base fuel of triptane were investigated. Two paraffins (triptane and S + 6.0 ml TEL/gal) and two refinery blends (28-R and 33-R) were preignition rated. The effect of changes in the following engine operating variables on preignition limit was determined: inlet-air temperature, rear spark plug gasket temperature, engine speed, spark advance, tappet clearance, and oil consumption. Preignition limits of the R-2800 cylinder using Champion C34S and C35S and AC-LS86, LS87, and LS88 spark plugs were established and the effect of spark plug deterioration was investigated. No definite trends in preignition-limited indicated mean effective pressure were indicated for aromatics as a class when increased percentages of different aromatics were added to a base fuel of triptane. Three types of fuel (aromatics, paraffins, and refinery blends) showed a preignition range for this cylinder from 65 to 104 percent when based on the performance of S plus 6.0 ml TEL per gallon as 100 percent. The R-2800 cylinder is therefore relatively insensitive to fuel composition when compared to a CFR F-4 engine, which had a pre-ignition range from 72 to 100 percent for the same fuels. Six engine operating variables were investigated with the following results: preignition-limited indicated mean effective pressure decreased, with increases in engine speed, rear spark plug gasket temperature, inlet-air temperature, and spark advance beyond 20 F B.T.C. and was unaffected by rate of oil consumption or by tappet clearance. Spark plugs were rated over a range of preignition-limited indicated mean effective pressure from 200 to 390 pounds per square inch at a fuel-air ratio of 0.07 in the following order of increased resistance to preignition: AC-LS97, AC-LS88, Champion C358, AC-LS86, and Champion C34S. Spark plug deterioration in the form of cracks in the porcelain had been broken away from the center electrode and were retained in the spark plug cavity, the preignition limit was decreased as much as 57 percent. When the broken pieces had been removed, the preignition limit increased from that of the undamaged porcelain as the weight of removed porcelain was increased.

Pfender, John F.↗
NASA NTRS1996

Dual Spark Plugs For Stratified-Charge Rotary Engine

Fuel efficiency of stratified-charge, rotary, internal-combustion engine increased by improved design featuring dual spark plugs. Second spark plug ignites fuel on upstream side of main fuel injector; enabling faster burning and more nearly complete utilization of fuel.

Abraham, John↗
NASA NTRS1920

Spark Plug Defects and Tests

The successful operation of the spark plug depends to a large extent on the gas tightness of the plug. Part 1 of this report describes the method used for measuring the gas tightness of aviation spark plugs. Part 2 describes the methods used in testing the electrical conductivity of the insulation material when hot. Part 3 describes the testing of the cold dielectric strength of the insulation material, the resistance to mechanical shock, and the final engine test.

Silsbee, F B↗
NASA NTRS1919

Temperatures in Spark Plugs Having Steel and Brass Shells

This investigation was conducted at the Bureau of Standards for the National Advisory Committee for Aeronautics. Brass has often been assumed superior to steel for spark plug shells because of its greater heat conductivity. The measurements described in this report prove the contrary, showing that the interior of a spark plug having a brass shell is from 50 degrees to 150 degrees c. (90 degrees to 270 degrees f.) hotter than that of a similar steel plug. Consistent results were obtained in both an aviation and a truck engine, and under conditions which eliminated all other sources of difference between the plugs. It is to be concluded that steel is to be preferred to brass for spark plug shells. This report embodies the results of measurements taken of electrodes and a comparison of brass and steel insulators of spark plugs while they were in actual operation. The data throw considerable light upon the problem of the proper control of temperatures in these parts.

Cragoe, C S↗
NASA NTRS1920

Properties and preparation of ceramic insulators for spark plugs

Report describes in detail the preliminary experiments which were made on the conductivity of spark-plug insulators in order to develop a satisfactory comparative method for testing various spark-plug materials. Materials tested were cements, porcelain, feldspar, and quartz.

Silsbee, F B↗
NASA NTRS1925

The sparking voltage of spark plugs

This report has been prepared in order to collect and correlate into convenient and useful form the available data on this subject. The importance of the subject lies in the fact that it forms the common meeting ground for studies of the performance of spark generators and spark plugs on the one hand and of the internal combustion engines on the other hand. While much of the data presented was obtained from various earlier publications, numerous places were found where necessary data were lacking, and these have been provided by experiments in gasoline engines at the Bureau of Standards.

Silsbee, F B↗
NASA NTRS1951

Preliminary results of turbojet-engine altitude-starting investigation

A spark energy of 2.13 joules per spark at 1 spark per second produced ignition to an altitude of 50,000 feet at a flight Mach number of 0.6. The minimum power requirements for ignition were obtained from a combination of low spark repetition rates and high spark energy. The altitude-ignition limit was also increased by increasing spark-gap immersion, fuel temperature, inlet-air temperature, and fuel volatility, and by decreasing flight Mach number. The maximum altitude at which flame propagation was accomplished from combusters with spark plugs to combusters without spark plugs to combustors without spark plugs was increased about 5000 feet by increasing fuel volatility.

COMBUSTION - IGNITION OF GASES↗
NASA NTRS1949

Comparison of Performance of AN-F-58 Fuel and Gasoline in J34-WE-22 Turbojet Engine

As part of an investigation of the performance of AN-F-58 fuel in various types of turbojet engine, the performance of this fuel in a 3000-pound-thrust turbojet engine has been investigated in an altitude test chamber together with the comparative performance of 62-octane gasoline. The investigation of normal engine performance, which covered a range of engine speeds at altitudes from 5000 to 50,000 feet and flight Mach numbers up to 1.00, showed that both the net thrust and average turbine-outlet temperatures were approximately the same for both fuels. The specific fuel consumption and the combustion efficiency at the maximum engine speeds investigated were approximately the same for both fuels at altitudes up to 35,000 feet, but at an altitude of 50,000 feet the specific fuel consumption was about 9 percent higher and the combustion efficiency was correspondingly lower with the AN-F-58 fuel than with gasoline. The low-engine-speed blow-out limits were about the same for both fuels. Ignition of AN-F-58 fuel with the standard spark plug was possible only with the spark plug in a clean condition; ignition was impossible at all flight conditions investigated when the plug was fouled by an accumulation of liquid fuel from a preceding false start. Use of an extended-electrode spark plug provided satisfactory ignition over a slightly smaller range of altitudes and flight Mach numbers than for gasoline with the standard spark plug.

Dowman, Harry W↗
NASA NTRS2017

Coil-On-Plug Ignition for LOX/Methane Liquid Rocket Engines in Thermal Vacuum Environments

A coil-on-plug ignition system has been developed and tested for Liquid Oxygen (LOX) / liquid methane rocket engines operating in thermal vacuum conditions. The igniters were developed and tested as part of the Integrated Cryogenic Propulsion Test Article (ICPTA), previously tested as part of the Project Morpheus test vehicle. The ICPTA uses an integrated, pressure-fed, cryogenic LOX/methane propulsion system including a reaction control system (RCS) and a main engine. The ICPTA was tested at NASA Glenn Research Center's Plum Brook Station in the Spacecraft Propulsion Research Facility (B-2) under vacuum and thermal vacuum conditions. In order to successfully demonstrate ignition reliability in the vacuum conditions and eliminate corona discharge issues, a coil-on-plug ignition system has been developed. The ICPTA uses spark-plug ignition for both the main engine igniter and the RCS. The coil-on-plug configuration eliminates the conventional high-voltage spark plug cable by combining the coil and the spark-plug into a single component. Prior to ICPTA testing at Plum Brook, component-level reaction control engine (RCE) and main engine igniter testing was conducted at NASA Johnson Space Center (JSC), which demonstrated successful hot-fire ignition using the coil-on-plug from sea-level ambient conditions down to 10(exp.-2) torr. Integrated vehicle hot-fire testing at JSC demonstrated electrical and command/data system performance. Lastly, Plum Brook testing demonstrated successful ignitions at simulated altitude conditions at 30 torr and cold thermal-vacuum conditions at 6 torr. The test campaign successfully proved that coil-on-plug technology will enable integrated LOX/methane propulsion systems in future spacecraft.

Melcher, John C.↗
NASA NTRS2017

Coil-On-Plug Ignition for Oxygen/Methane Liquid Rocket Engines in Thermal-Vacuum Environments

A coil-on-plug ignition system has been developed and tested for Liquid Oxygen (LOX)/liquid methane (LCH4) rocket engines operating in thermal vacuum conditions. The igniters were developed and tested as part of the Integrated Cryogenic Propulsion Test Article (ICPTA), previously tested as part of the Project Morpheus test vehicle. The ICPTA uses an integrated, pressure-fed, cryogenic LOX/LCH4 propulsion system including a reaction control system (RCS) and a main engine. The ICPTA was tested at NASA Glenn Research Center's Plum Brook Station in the Spacecraft Propulsion Research Facility (B-2) under vacuum and thermal vacuum conditions. A coil-on-plug ignition system has been developed to successfully demonstrate ignition reliability at these conditions while preventing corona discharge issues. The ICPTA uses spark plug ignition for both the main engine igniter and the RCS. The coil-on-plug configuration eliminates the conventional high-voltage spark plug cable by combining the coil and the spark plug into a single component. Prior to ICPTA testing at Plum Brook, component-level reaction control engine (RCE) and main engine igniter testing was conducted at NASA Johnson Space Center (JSC), which demonstrated successful hot-fire ignition using the coil-on-plug from sea-level ambient conditions down to 10(exp -2) torr. Integrated vehicle hot-fire testing at JSC demonstrated electrical and command/data system performance. Lastly, hot-fire testing at Plum Brook demonstrated successful ignitions at simulated altitude conditions at 30 torr and cold thermal-vacuum conditions at 6 torr. The test campaign successfully proved that coil-on-plug technology will enable integrated LOX/LCH4 propulsion systems in future spacecraft.

Melcher, John C.↗
DOE OSTI2025

Enabling Low-Temperature (LTP) Ignition Technologies for Multi-Mode Engines through the Development of a Validated High-Fidelity LTP Model for Predicative Simulations Tools

The goal of multi-mode engine architectures is to extend current lean-burn dilution limits with renewable fuels, which requires spark plugs to deposit high energies (hundreds of mJ) in order to initiate ignition and complete combustion. At elevated energy deposition rates, spark plugs experience increased electrode erosion and thermal losses, which ultimately shortens the spark-plug lifetime and lowers ignition efficiency. As such, in order to safeguard the efficiency gains of multi-mode concepts, new and improved ignition technologies are required. Recently, non-equilibrium low-temperature plasmas (LTP) have been shown to promote energy-efficient ignition via quenching and transport of electronically excited atoms and molecules, selective radical production and fast heating of hydrocarbon/air mixtures [1-2]. Thus, LTP is seen as a technology that can potentially improve the energy extraction efficiency of fuels, while enabling kinetically controlled combustion modes towards fuel leaner conditions to realize current DOE VTO goals of improving the sustainability of future mobility [3]. Although many previous studies have demonstrated the efficacy of plasma-assisted ignition to enhance combustion, the detailed enhancement mechanisms remain largely unknown, especially for oxygenated fuels and at elevated pressures that are most relevant to practical engine conditions. These barriers hinder the development of accurate and comprehensive numerical models that seek to describe LTP-based ignition in existing engine design software tools and methods. Current state-of-the-art simulation capabilities for LTP ignition systems are in need of improvements since they deliver qualitative results only due to important limitations of existing approaches. Firstly, validated kinetic models with elementary steps for plasma discharges in oxygenated fuel/air mixtures of relevance to the transportation sector are required. Such kinetic models do not exist at present and will be developed and validated within this project. Secondly, plasma discharges and reactive mixture ignition are multi-scale, unsteady processes requiring high-performance numerical methods and software that execute efficiently on DOE supercomputers. Such software does not exist at present and will be developed and applied to practical LTP ignition scenarios as part of this project. Thirdly, experimental databases that are tailored to serve as benchmark in support of the development of predictive computational models of LTP ignition do not exist and will be part of this project.

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRS1938

Experimental Study of Ignition by Hot Spot in Internal Combustion Engines

In order to carry out the contemplated study, it was first necessary to provide hot spots in the combustion chamber, which could be measured and whose temperature could be changed. It seemed difficult to realize both conditions working solely on the temperature of the cooling water in a way so as to produce hot spots on the cylinder wall capable of provoking autoignition. Moreover, in the majority of practical cases, autoignition is produced by the spark plug, one of the least cooled parts in the engine. The first procedure therefore did not resemble that which most generally occurs in actual engine operation. All of these considerations caused us to reproduce similar hot spots at the spark plugs. The hot spots produced were of two kinds and designated with the name of thermo-electric spark plug and of metallic hot spot.

Serruys, Max↗
NASA NTRS1940

Correlation of knocking characteristics of fuels in an engine having a hemispherical combustion chamber

Data are presented to show the effects of inlet-air pressure, inlet-air temperature, and compression ratio on the maximum permissible performance obtained with having a hemispherical-dome combustion chamber. The five aircraft-engine fuels used have octane numbers varying from 90 to 100 plus 2 ml of tetraethyl lead per gallon. The data were obtained on a 5 1/4-inch by 4 3/4-inch liquid-cooled engine operating at 2,500 r.p.m. The compression ratio was varied from 6.0 to 8.9. The inlet-air temperature was varied from 110 to 310 F. For each set of conditions, the inlet-air pressure was increased until audible knock occurred and then reduced 2 inches of mercury before data were recorded. The results for each fuel can be correlated by plotting the calculated end-gas density factor against the calculated end-gas temperature. Measurements of spark-plugs, cutting off the switch to one spark plug lowered the electrode temperature of that plug from a value of 1,365 F to a value of 957 F. The results indicate that the surface temperatures of combustion-chamber areas which become new sources of ignition markedly increase after ignition.

Rothrock, A M↗
NASA NTRS2008

Igniters for Liquid Oxygen/Liquid Methane Technology Development

As part of NASA's technology development of liquid methane / liquid oxygen engines for future exploration missions, two different igniters were recently studied at NASA Marshall Space Flight Center. The first igniter tested was an impinging injection, spark-initiated torch igniter, and the second was a microwave-generated plasma igniter. The purpose of the ignition tests was to define the ignition limits under vacuum conditions and characterize the transient start-up performance as a function of propellant mixture ratio (MR), mass flow rates, inlet temperatures, and pre-ignition chamber pressure. In addition, for the impinging igniter two different spark plugs were tested, and for the microwave igniter the magnetron filament warm-up time and the magnetron input power were both varied. The results gathered from these tests indicated that the impinging igniter is capable of operating over an MR range of 2 - 27, with methane and oxygen inlet temperatures as low as -161 F and -233 F, respectively. The microwave igniter was tested over an MR range of 2 - 9, with methane and oxygen inlet temperatures as low as -90 F and -200 F, respectively. The microwave igniter achieved ignition over this range, although an upper ignition limit was determined for the oxidizer mass flow rate. In general, the torch exhaust temperatures for the microwave igniter were not as high as those attained with the impinging igniter. The microwave igniter, however, was hot-fired 17 times and was still operational, whereas the impinging igniter spark plugs experienced thermal shock and erosion over nine hot-fire tests. It was concluded that for the microwave igniter better mixing of the propellants might be required in order to both raise the torch exhaust temperature and decrease the required magnetron input power, and for the impinging igniter the spark plug position within the igniter chamber should be varied in future tests to identify a more optimal location. All of the igniter tests were supported by the Propulsion & Cryogenics Advanced Development project, which is part of NASA's Exploration Technology Development Program.

Osborne, Robin J.↗