Search NASA⌕ Search

SEARCH · Search NASA

Results for “specific surface area”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Enzymatic depolymerization of polyester: Foaming as a pretreatment to increase specific surface area

Abstract Poly(ethylene terephthalate) (PET) is widely used for its high strength‐to‐weight ratio, gas barrier properties, and chemical resistance. The growing PET use highlights the demand for a better recycling system. Enzymatic recycling, alongside mechanical and chemical methods, is eco‐friendly and yields properties similar to virgin PET. Substrate properties ( T g , crystallinity, and specific surface area [SSA]) and enzyme stability significantly impact conversion efficiency. Higher SSA and lower crystallinity tend to yield improved depolymerization when employing leaf compost‐cutinase (LCC‐ICCG) enzymes. This study explored melt extrusion and foaming as pretreatment techniques to modify PET structural properties, using a low‐cost chemical foaming agent (CFA). The monomer conversion rate and efficiency during depolymerization were measured and related to the processing, extrudate micro‐ and meso‐structure, and polyester type. Pretreated PET substrates showed reduced T g , crystallinity, density, and enhanced SSA, resulting in a 90% mass loss for foamed RPET and VPET substrates within 2 days. In contrast, PET with ~30% of cyclohexanedimethanol comonomer exhibited a nearly 50% lower depolymerization rate, with zero BHET production. It indicates that the combination of low crystallinity, low T g , and high SSA leads to improved monomer conversion. These findings emphasize the significance of amorphization and foaming in enhancing PET enzymatic depolymerization.

42 ENGINEERING↗
DOE OSTI2026

Consolidation and Permeability of the B1 and D1 Gas Hydrate Bearing Sands and Associated Seal Sediments of the Extended-Duration Gas Production Test Site on the Alaska North Slope

Gas hydrate, a solid combination of gas (mostly methane in nature) and water molecules stable at low temperatures and elevated pressures, occurs naturally in marine and permafrost-associated environments. Gas hydrate reservoirs, such as those in the Alaska North Slope, have been considered potential energy resources for gas production. To understand the petrophysical and geo-mechanical characteristics of the reservoir, core samples retrieved from the site of the JOGMEC-DOE-USGS collaborative gas hydrate R&D project have been analyzed in the laboratory for their hydraulic and mechanical properties. This paper focuses on both seal and reservoir samples associated with the B1 and D1 sands, which are evaluated for index properties (including porosity, grain size distribution, liquid and plastic limits, specific surface area, and specific gravity), consolidation, permeability, and water retention. Furthermore, the reservoir core samples were tested with pore-filling, laboratory-grown tetrahydrofuran hydrate, in order to assess reservoir behavior during gas production from hydrates. Under simulated in situ stress conditions, the seal and hydrate-free reservoir cores had a permeability anisotropy ratio of k h /k v = 3.0−5.0, and k h /k v = 2.4−3.0 for the reservoir tetrahydrofuran hydrate-bearing cores. The data suggest that depressurizing the reservoir to induce hydrate dissociation alters the reservoir effective permeability in three ways: permeabilities decrease due to porosity lost (e.g., the initial reservoir thickness can decrease by up to 5% upon 7 MPa depressurization), permeability increases due to the loss of solid hydrate in the pore space, and permeability anisotropy k h /k v decreases in response to the evolving pore-space geometry. We show that given the simulated in situ gas hydrate saturations (i.e., S h = 32% in core 7P-2E and S h = 21% in core 20P-4), gas production from the dissociation of tetrahydrofuran hydrate in the two tested cores results in a net increase in effective permeability and a decrease in k h /k v . This study highlights the importance of investigating seal and reservoir sediments and the impacts of depressurization on the porosity and permeability responses during production.

Geological materials↗
DOE OSTI2025

Microstructure Scale Lithium-Ion Battery Modeling: Part III. When and Where Lithium Plating Occurs and its Correlation with the Electrode Microstructure

Li-ion battery performance and degradation are closely related to the cell’s underlying electrode microstructure. Electrode microstructures are typically characterized with volume-averaged properties that neglect the impact of local heterogeneities. However, local heterogeneities create hot spots that can trigger degradation onset. Herein, a microstructure scale electrochemical model is used to investigate the impact of microstructure heterogeneity on lithium plating. The model predicts lithium plating is not uniform, even when considering a relatively small portion of the electrode (a cross-sectional area of 154×144 µm 2 ), preferring to plate on larger particles as compared to smaller particles. While local heterogeneities control where plating occurs, the model predicts that volume-averaged properties control when plating occurs. Additionally, the model predicts that the active material specific surface area has a linear relationship with the plating onset. However, the linear relationship between increased active material surface area and delayed plating response appears to be sensitive to the microstructure feature used to increase the active interface area. Here, a comparative case-study is explored where the specific surface area is increased by either reducing the active material particle diameter, adding open-porosity cracks, or increasing the active material surface roughness. The model predicts that increasing the specific surface area by reducing the active material particle diameter is the most effective strategy for delaying lithium plating. At 6C, reducing particle size is shown to be 3 and 20 times more effective than, respectively, adding open-porosity cracks and increasing surface roughness. A dual-layer electrode architecture combining gradations both for average properties and uniformities is eventually proposed to improve homogeneous material utilization and reduce degradation at high charge rates.

25 ENERGY STORAGE↗
DOE OSTI2025

Rigid Supramolecular Aramid Nanotubes as Catalyst Supports

Solution‐phase heterogeneous catalysts benefit from nanoscale dimensions, which maximize specific surface area and enhance catalytic activity. However, the ease of recovering such nanocatalysts depends on the design of the support materials, which are often particle‐like. Rigid 1D nanomaterials are proposed as supports that can enhance separability while offering high volumetric specific surface area for greater catalyst loading and activity. Here, aramid amphiphiles (AAs) are designed to spontaneously self‐assemble in water into high‐aspect‐ratio supramolecular nanotubes with tunable surface chemistry. These AA nanotubes exhibit high persistence lengths (P = 750 ± 340 µm) and mechanical stiffnesses (3 N/m). Incorporating surface thiol groups enables immobilization of catalytic gold nanoparticles. The resulting AA nanotube‐gold nanoparticle complexes exhibit high catalytic activity, efficient recoverability via simple microfiltration, and sustained reusability over ten reaction cycles. This study demonstrates the utility of molecular self‐assembled 1D nanomaterials as versatile scaffolds for the reuse and recovery of nanoscale catalysts.

1D nanomaterials↗
DOE OSTI2025

Microstructurally Strained Pyrochlore–Perovskite Biphasic Electrocatalysts for the Oxygen Evolution Reaction

Efficiency of water splitting for hydrogen production is often limited by the sluggish kinetics of multiple electronic transfers required in the heterogeneous oxygen evolution reaction (OER). Catalyst design for reducing the high OER overpotential remains a major scientific challenge. Lattice-strain engineering, a method for tuning the electronic structure and surface geometric configuration of active sites, may greatly affect the interaction between adsorbates and catalytic surfaces for high activity and stability. Here, in this study, we present the synthesis of biphasic oxides of YPrSrRuMnO x , which consists of distinct phases of Y 2 Ru 2 O 7 pyrochlore and (Pr 0.7 Sr 0.3 )MnO 3 perovskite, and the development of a suitable analytical approach to study the strain–catalytic property relationship. Linear sweep voltammetry results reveal that the biphasic oxide exhibits approximately 3.1 times greater mass activity and 2.4 times larger turnover frequency (TOF) than single-phase Y 2 Ru 2 O 7 in the 0.1 M HClO 4 electrolyte. The biphasic catalyst is also about 3 times more stable than the single-phase oxide under acidic conditions. X-ray photoelectron spectroscopy, nitrogen isotherm, and electrochemical surface area analyses indicate that the oxidation state, specific surface area, and electrochemical surface area do not cause enough difference in the observed enhancement of OER performance. We examined the effects of microstrain on electrocatalysis, originating from lattice mismatch between different phases, using three different structural models. Specifically, we compared the Williamson–Hall method, standard stress–strain analysis, and Rietveld refinement in analyzing the structure–property relationship. Strain mapping using geometric phase analysis (GPA) further revealed significant microstrain and lattice dislocations localized near phase boundaries in the biphasic oxide, in contrast to the uniform strain in single-phase materials. The results reveal that the increased microstrain correlates well with the improved OER performance, as the biphasic oxide catalyst exhibits 2–3 times greater microstrain than Y 2 Ru 2 O 7 pyrochlore.

electrocatalysts↗
DOE OSTI2025

Influence of calcium nitrate timing on the structural and textural characteristics of mesoporous SiO 2 -CaO nanoparticles

Mesoporous bioactive glass nanoparticles (MBGNPs) are promising materials for drug delivery due to their high pore volume and specific surface area. This study investigates how the timing of calcium nitrate addition affects the structural and textural characteristics of MBGNPs synthesized via a microemulsion-assisted sol-gel method. Delayed calcium nitrate addition reduced calcium incorporation from 14.2 to 9.5 mol% and increased particle size from 178 ± 51 nm to 256 ± 30 nm. The specific surface area values increased with the delayed addition of calcium nitrate, as observed through BET and USAXS/SAXS measurements. The proportion of Q Si n units slightly changed, but no cytotoxicity was observed in osteoblast-like cells. These findings provide valuable insights into optimizing MBGNP synthesis for biomedical applications.

Calcium nitrate tetrahydrate↗
DOE OSTI2024

Manufacturing of Fabric Electrodes using a High-Throughput Screening Platform for Redox Flow Batteries

The objective of this project is to establish a new manufacturing methodology with machine learning- based high-throughput screening for the design and development of hierarchical structured, high-performance fabric electrodes for redox flow batteries (RFBs). The end goal of the project is to design and manufacture fabric electrodes for RFB applications that can provide 250 mA/cm2 current density operation for 100-cycles with 80% average energy efficiency. This was accomplished by first examining the structure-performance-property linkages of the electrodes provided by our partner, AvCarb. The electrodes’ microstructure was characterized by determining their pore size distribution, tortuosity, specific surface area, and porosity. The ohmic, charge transfer and mass transfer resistances were then calculated using electrochemical impedance spectroscopy. Carbon cloth electrodes showed the greatest resistance, which was dominated by charge transfer resistance, which we believe is related to the surface functionalization. Full cell cycling was used in order to determine the area specific resistance and energy efficiency of the cells. All of this experimental data and the results of the mathematical model (to increase the amount of inputs with parametric sweeping) were used to develop a machine learning-based model for the design of high-performance fabric electrodes. Using the results from the machine learning tool, optimized electrodes were fabricated by AvCarb. The ohmic, charge transfer and mass transfer resistances for these new electrodes were measured, and both performed better than any of the initial samples which had been provided by AvCarb.

25 ENERGY STORAGE↗
DOE OSTI2025

Effects of chemical composition and physicochemical properties of poplar biomass on the performance of 3D printed poplar-reinforced PLA materials

Lignocellulosic biomass has been well-acknowledged as a filler for making 3D printed composites. The technical performances of composites were influenced by the characteristics of the components. The correlations between poplar biomass properties and the mechanical and thermal performances of the 3D printed poplar-plastic composites were investigated. The characteristics of poplar were modified by different pretreatment methods, including using hot water, dilute acid, and organic solvent (organosolv), and each treated poplar biomass was applied as a filler in a polylactic acid (PLA) polymer matrix to produce eco-friendly materials. These solvent pretreatments increased the hydrophobicity and surface area of poplar. Organosolv treated poplar showed the highest cellulose content and significantly increased Young's modulus of its biocomposites. Principal component analysis revealed that the specific surface area and water contact angle of biomass contributed to the thermal stability of biocomposites. Additionally, the degree of polymerization of cellulose and xylan content within the biomass correlated with the biocomposites' break stress. Notably, the crystallinity of biocomposites impacted the modulus of these materials. The reported relationships between biomass characteristics and 3D printed composite behaviors provide guidance for optimizing biomass processing in biocomposite applications.

Ji, Anqi [State Univ. of New York (SUNY), Syracuse↗
DOE OSTI2024

Upcycling Low Linear Density Polyethylene Waste into Turbostratic Graphene for High Mass Loading Supercapacitors

In this work, LLDPE was upcycled into a high quality turbostratic graphene using a pre-treatment step to oxidatively crosslink the polymer with the assistance of solid additives (KCl and K2CO3) that improve crosslinking by increasing the effective surface area of the polymer melt during processing. After this pretreatment step, the crosslinked polymer could then be carbonized and catalytically graphenized between 400-950 °C without complete decomposition of the material. The LLDPE derived graphene (LLDPE-G) obtained from this process has a Brunauer–Emmett–Teller (BET) specific surface area, up to 1800 m2g-1 and average Raman ID/IG and I2D/IG ratios of 0.85 and 0.57, respectively, indicating high quality graphene. When used as an electrode material in symmetric supercapacitors, LLDPE-G possesses an outstanding specific capacitance up to 175 Fg-1 at a mass loading of 20 mgcm-2, which is two times the commercial requirement, yielding an excellent areal capacitance of 3.5 Fcm-2. Moreover, LLDPE-G exhibits exceptional cycling stability with a capacitance retention of 95.8% after 100,000 cycles at a current density of 4.0 Ag-1. Additionally, the KCl and K2CO3 were recycled and reused over 3 complete cycles to make new LLDPE-G with the material quality and electrocapacitive performance retained and verified after each cycle. Our approach creates new opportunities for upcycling not only waste LLDPE but also other varieties of PE to high value graphene materials.

Gao, Yuan [NETL Site Support Contractor, National ↗
DOE OSTI2024

Microscopic 3D Graphene for High-Performance Supercapacitors with Ultra-High Areal Capacitance

Despite graphene being considered as an ideal supercapacitor electrode material, its use in commercial devices is limited because few methods exist to produce high-quality graphene at large scale and low-cost. We report a simple method to synthesize 3D graphene by graphenization of coal tar pitch with a K2CO3 catalyst. This produces 3D graphenes with high specific surface areas up to 2113 m2 g-1 and exceptional crystallinity (Raman ID/IG as low as ~ 0.15). The material has an outstanding specific capacitance of 182.6 F g-1 at a current density of 1.0 A g-1. This occurs at mass loading of 30 mg cm-2 which is 3 times higher than commercial requirements, yielding an ultra-high areal capacitance of 5.48 F cm-2. Moreover, the K2CO3 is recycled and reused over 10 cycles. The synthesis method and resulting electrocapacitive performance properties create new opportunities for using 3D graphene more broadly in practical supercapacitor devices.

Pham, Viet Hung↗
DOE OSTI2024

Upcycling linear low-density polyethylene waste to turbostratic graphene for high mass loading supercapacitors

Linear low-density polyethylene (LLDPE) waste is difficult to upcycle into more valuable carbon materials because it tends to completely decompose into small molecules during thermal processing. In this work, LLDPE is upcycled into a high quality turbostratic graphene using a pre-treatment step to oxidatively crosslink the polymer with the assistance of solid additives (KCl and K 2 CO 3 ) that improve crosslinking by increasing the effective surface area of the polymer melt during processing. After this pretreatment step, the crosslinked polymer could then be carbonized and catalytically graphenized between 400–950°C without decomposition of the polymer feedstock. The LLDPE derived graphene (LLDPE-G) obtained from this process has a Brunauer–Emmett–Teller (BET) specific surface area, up to 1800m 2 g -1 and average Raman I D /I G and I 2D /I G ratios of 0.85 and 0.57, respectively, indicating high quality graphene. When used as an electrode material in symmetric supercapacitors, LLDPE-G possesses a specific capacitance up to 175Fg -1 at a mass loading of 20mgcm -2 , which is two times the commercial requirement, yielding an areal capacitance of 3.5 Fcm -2 . Moreover, LLDPE-G exhibits exceptional cycling stability with a capacitance retention of 95.8 % after 100,000 cycles at a current density of 4.0 Ag -1 . Additionally, the KCl and K 2 CO 3 solids are recycled and reused over 3 complete reaction cycles to make new LLDPE-G with the material quality and electrocapacitive performance retained and verified after each cycle. Our approach creates new opportunities for upcycling waste LLDPE and other varieties of polyethylene into a higher value graphene used for electrochemical energy storage applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Upcycling Polyethylene Waste Into Hybrid Graphitic Porous Carbon Materials Used in High-Performance Zinc-Ion Hybrid Capacitors

Polyethylene (PE) waste is a challenge to upcycle into useful materials because this plastic tends to decompose into volatile compounds when heated at relatively low temperatures. In this work, we report a chemical process that addresses this challenge by converting mixtures of linear low-density polyethylene (LLDPE), low-density polyethylene (LDPE), and high-density polyethylene (HDPE) waste into a hybrid graphitic porous carbon (HGPC) that can be used as a zinc-ion hybrid capacitor cathode. The process uses a low temperature thermal oxidation pre-treatment step, with assistance of an inert solid additive (KCl) to increase the effective surface area of the PE melt, to functionalize, cross-link, and stabilize the PE waste followed by carbonization and catalytic graphitization steps at higher temperatures with a potassium carbonate (K2CO3) catalyst. The PE waste derived HPGC (PW-HPGC) has a hybrid structure composed of graphene-like carbon nanosheets grown on the surface of carbon particles, high porosity with the Brunauer–Emmett–Teller (BET) specific surface area up to 1,763 m2g-1, and good graphitic degree with average Raman I2D/IG ratios of 0.53. When used as a cathode material for zinc-ion hybrid capacitors, this PW-HGPC exhibits an excellent specific capacity up to 126.7 mAhg-1 at high mass loading of 10 mgcm-2. Moreover, PW-HGPC exhibits remarkable cycling stability with capacity retention of >94% after 10,000 cycles at a current density of 2.0 A g-1.

hybrid graphitic porous carbon↗
DOE OSTI2024

A comprehensive study on two types of supercapacitor composite electrodes comprising MnO 2 and activated carbon nanofibers: Self-supporting membrane and ground powder

Manganese dioxide (MnO 2 )@carbon composites have been attractively considered as electrode materials for supercapacitors (SCs) due to synergistic effects. This work systematically investigated the structure of MnO 2 @carbon nanofiber (CNF) composite electrodes with the different forms of CNFs and the corresponding electrochemical performance of SCs. In brief, novel activated carbon nanofibers were first fabricated by electrospinning the hydroxyl-containing poly(amic acid) solution, and then the preferred CNF material was decorated by MnO 2 crystals in the form of self-supporting membrane and ground powders, respectively. Additionally, the synthesis parameters were investigated and optimized based on the electrochemical performance of SCs. The results reveal that the powdered composite electrode exhibits a higher specific surface area of 501 m 2 g –1 compared to the self-supporting membrane composite electrode under the same conditions, resulting in a promising specific capacity of 214.1 mAh g –1 (770.8 Fg –1 ) in 6M KOH solution at 0.5 A g –1 . In addition, the capacitance of the symmetrical SC device assembled by G-HMC-1:3–80 reaches 179.8 Fg –1 , coupled with an energy density of 24.86 Whkg –1 at 230 Wkg –1 power density. This work provides valuable hints for designing SC composite electrode materials with outstanding performance.

25 ENERGY STORAGE↗
DOE OSTI2024

Upcycling Linear Low-Density Polyethylene Waste into Graphene for High Mass Loading Supercapacitors

Upcycling plastic into advanced carbons, such as graphene and porous carbon, offers attractive options to manage waste streams by converting the plastic into carbon electrode materials for energy storage devices. Linear low density polyethylene (LLDPE) is firstly bulk-oxidized with a facile and scalable method and then carbonized and catalyticlly graphenized into porous graphene materials. The LLDPE derived graphene (LLDPE-G) has a BET specific surface area up to 1800 m2/g and Raman ID/IG ratio of 0.85. When used as electrode material for symmetric supercapacitor, LLDPE-G possesses outstanding specific capacitance and excellent areal capacitance. Moreover, LLDPE-G exhibits exceptional cycling stability with capacitance retention of 95.8% after 100,000 cycles. Last but not least, KCl is recycled and reused over 3 cycles with material quality and electrocapacitive performance of LLDPE-G retained and verified after each cycle.

Gao, Yuan↗
DOE OSTI2024

Synthesis of Microscopic 3D Graphene for High‐Performance Supercapacitors with Ultra‐High Areal Capacitance

Abstract Despite graphene being considered an ideal supercapacitor electrode material, its use in commercial devices is limited because few methods exist to produce high‐quality graphene at a large scale and low cost. A simple method is reported to synthesize 3D graphene by graphenization of coal tar pitch with a K 2 CO 3 catalyst. This produces 3D graphenes with high specific surface areas up to 2113 m 2 g −1 and exceptional crystallinity (Raman I D / I G as low as ≈0.15). The material has an outstanding specific capacitance of 182.6 F g −1 at a current density of 1.0 A g −1 . This occurs at a mass loading of 30 mg cm −2 which is 3 times higher than commercial requirements, yielding an ultra‐high areal capacitance of 5.48 F cm −2 . The K 2 CO 3 is recycled and reused over 10 cycles with material quality and electrocapacitive performance of 3D graphene retained and verified after each cycle. The synthesis method and resulting electrocapacitive performance properties create new opportunities for using 3D graphene more broadly in practical supercapacitor devices.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Upcycling Linear Low-Density Polyethylene Waste into Graphene for High Mass Loading Supercapacitors

Polyethylene is notoriously difficult to upcycle because it decomposes into light gases at approximately 350-400 °C which prevents processing it at higher temperatures to convert it into electrode materials. We address this challenge by using an air-based, thermos-oxidative process, which heats linear low-density polyethylene (LLDPE) just below the decomposition point to initiate oxidation and cross-linking of LLDPE alkyl chains. These molecular transformations allow LLDPE to be graphenized at 950 °C without decomposing. The LLDPE-derived graphene (LLDPE-G) has a BET specific surface area up to 1,800 m2/g and Raman ID/IG ratio of 0.85. When used as electrode material for a symmetric supercapacitor with the 1 M H2SO4 electrolyte, LLDPE-G possesses an specific capacitance up to 175 F/g at mass loading of 20 mg/cm2, yielding an areal capacitance of 3.5 F/cm2. The cycling stability with capacitance demonstrates a retention of 95.8% after 100,000 cycles at high current density of 4.0 A/g.

Gao, Yuan↗
DOE OSTI2025

Upcycling Polyethylene Waste into Hybrid Graphitic Porous Carbon Materials Used in High‐Performance Zinc‐Ion Hybrid Capacitors

Polyethylene (PE) waste is a challenge to upcycle into useful materials because this plastic tends to decompose into volatile compounds when heated at relatively low temperatures. In this work, mixtures of PE wastes into a hybrid graphitic porous carbon (HGPC) by a thermal oxidation pretreatment step, with assistance of an inert solid additive (KCl), to functionalize, crosslink, and stabilize the PE waste followed by carbonization and catalytic graphitization steps with a potassium carbonate catalyst, are upcycled. The PE waste‐derived HGPC (PW‐HGPC) has a hybrid structure composed of graphene‐like carbon nanosheets grown on the surface of carbon particles, high porosity with specific surface area, up to 1,763 m 2 g −1 , and good graphitic degree with average Raman I 2D / I G ratios of 0.53. When used as cathode material for zinc‐ion hybrid capacitors, this PW‐HGPC exhibits an excellent specific capacity, up to 126.7 mAh g −1 , at high mass loading of 10 mg cm −2 . Moreover, PW‐HGPC exhibits remarkable cycling stability with capacity retention of >94% after 10 000 cycles. Additionally, the KCl is recycled and reused over five times. This method provides a new solution for upcycling PE wastes into high value‐added carbon materials, not only for zinc‐ion hybrid capacitors but also for other electrochemical energy storage device applications.

hybrid graphitic porous carbon↗
DOE OSTI2025

Data for: Climatic Imprint on Interfacially-Controlled Platinum-Palladium Resources

Data package for manuscript "Climatic Imprint on Interfacially-Controlled Platinum-Palladium Resources" by Emily G. Wright, Ivey Wang, Yihang Fang, Elaine D. Flynn, and Jeffrey G. Catalano. This dataset contains adsorption results from experiments designed to investigate the effect of chloride on Pd(II) adsorption to goethite and Pt(II) adsorption to hematite and goethite, including lab experiments, X-ray absorption fine structure spectroscopy, and models of retention within a laterite. See the associated manuscript for full methods information. The file "Wright2025_PtAds_data.csv" contains the target starting Pt concentration (uM), final aqueous Pt and associated error (in uM), calculated adsorbed Pt and associated error (in umol/m2), target and measured aqueous chloride (mM), target aqueous nitrate (mM), final pH, and mineral concentration/loading (g/L). Associated mineral-free controls (mineral loading = 0 g/L) are included; the aqueous Pd error was not calculated and chloride was not measured in every sample. These data appear in Figures 1, S3, S4, S5, S20, and S22 in the associated manuscript. The file "Wright2025_PdAds_data.csv" contains the target starting Pd concentration (uM), final aqueous Pd and associated error (in uM), calculated adsorbed Pd and associated error (in umol/m2), target and measured aqueous chloride (mM), and mineral concentration/loading (g/L). Associated mineral-free controls (mineral loading = 0 g/L) are included; the aqueous Pd error was not calculated and chloride was not measured in every sample. These data appear in Figures 1, S3, S4, S5, and S20 in the associated manuscript. The file "Wright2025_MineralBatches_data.csv" contains the mineral identity and BET specific surface area (m2/g) for every mineral batch synthesized and used in experiments. The annealing time used is listed for hydrothermally annealed goethite. These data appear in Table S2 in the associated manuscript. The file "Wright2025_XRD_data.csv" contains the XRD patterns for every mineral batch synthesized as the counts as a function of two theta (in degrees). See "Wright2025_MineralBatches_data.csv" for more details on specific mineral batches. These data appear in Figure S2 in the associated manuscript. The file "Wright 2025_ZetaPotential_data.csv" contains the measured zeta potentials for samples of goethite (batch G2) at pH 4 the presence of varying amounts of sodium chloride. These data appear in Table S3 in the associated manuscript. The file "Wright2025_XAFSSamples_data.csv" contains the specific mineral batch, measured final aqueous Pd or Pt (uM), measured final aqueous chloride (mM), and estimated adsorbed Pd or Pt (umol/m2) of all XAFS samples. These data appear in Tables S4, S7, S8, and S10 in the associated manuscript. The files "Wright2025_PdXAFS_data.csv" and "Wright2025_PtXAFS_data.csv" contain the normalized spectra of Pd and Pt, respectively, adsorbed to minerals at varying chloride concentrations. See "Wright2025_XAFSSamples_data.csv" for a guide to sample names. Note that "05" in a sample name is equivalent to "0.5". These data appear in Figures 2, S6, S7, S8, S12, S13, and S14 in the associated manuscript. The file "Wright2025_LateriteProfileProfileModelParameters_data.csv" include the ratio of hematite to hematite and goethite in two synthetic, modeled profiles, as well as the modeled surface areas of goethite and hematite as a function of relative depth within the modeled weathering zone. These data were used, in conjunction with equations presented in the paper, to calculate the theoretical concentrations of Pd and Pt (and the resulting Pt/Pd ratio) within the profiles. These data appear in Figure 3 in the associated manuscript. The file "Wright2025_Imagery_data.zip" is a zipped folder containing the TEM and STEM images appear in Figures S18 and S19. Individual files are labeled as either STEM (Fig. S18) or TEM (Fig. S19) with a letter representing the part of the multipart figure.

58 GEOSCIENCES↗