Search NASA⌕ Search

SEARCH · Search NASA

Results for “spiral generator”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

An Investigation into High Voltage Spiral Generators Utilizing Thyristor Input Switches

High voltage nanosecond pulses are widely used in scientific research, but their wider adoption in industry requires compact, cost effective and easy to use generators to be developed. This paper presents modelling and experimental investigations into one method of producing such pulses – a spiral generator with a solid-state, thyristor-based input switch. It includes how the pulses are formed within the spiral, why a high speed input switch is required, how the geometry of the spiral dictates its output characteristics, and the effects of different loads. Using thyristors, often connected in series to increase the operating voltage of the spiral, enables the spiral generators to have low jitter, high repetition rate, and long lifetime. Modelling of the circuit used a combination of telegraph equations to account for the wave propagation along the spiral and a lumped circuit exchanging charge between the spiral, the input switch, and the load. The model is verified by detailed experimental results with the relative error being < 10% in most cases. Here, the output voltage pulse was often observed to have an initial peak of much lower magnitude than the subsequent peak(s) – which can only be fully explained by considering wave propagation effects. Lower input switch inductance, shorter switching time, larger mean diameter of the spiral, and increasing the width of the copper tape that makes up the spiral can all increase the voltage multiplication efficiency. Though increasing the number of turns that make up the spiral can increase the output voltage, it can also lower the multiplication efficiency. By understanding the effects of different geometries the spiral can be optimized to drive different loads - three applications of such spiral generators are then presented: pulses with 10 kV amplitude and 10 kHz repetition rate for driving DBD plasma, pulses with amplitude of 10 kV and 10 kV/ns rising rate for triggering of advanced solid state switches, and pulses with -50 kV amplitude and 50 ns rising time for triggering high current gas switches through field distortion.1 Index Terms—spiral generator, nanosecond pulses, telegraph equations, series-connected thyristor module, pulse forming process

42 ENGINEERING↗
NASA NTRS1985

Generated spiral bevel gears: Optimal machine-tool settings and tooth contact analysis

Geometry and kinematic errors were studied for Gleason generated spiral bevel gears. A new method was devised for choosing optimal machine settings. These settings provide zero kinematic errors and an improved bearing contact. The kinematic errors are a major source of noise and vibration in spiral bevel gears. The improved bearing contact gives improved conditions for lubrication. A computer program for tooth contact analysis was developed, and thereby the new generation process was confirmed. The new process is governed by the requirement that during the generation process there is directional constancy of the common normal of the contacting surfaces for generator and generated surfaces of pinion and gear.

Litvin, F. L.↗
NASA NTRS1985

Generated spiral bevel gears - Optimal machine-tool settings and tooth contact analysis

Geometry and kinematic errors were studied for Gleason generated spiral bevel gears. A new method was devised for choosing optimal machine settings. These settings provide zero kinematic errors and an improved bearing contact. The kinematic errors are a major source of noise and vibration in spiral bevel gears. The improved bearing contact gives improved conditions for lubrication. A computer program for tooth contact analysis was developed, and thereby the new generation process was confirmed. The new process is governed by the requirement that during the generation process there is directional constancy of the common normal of the contacting surfaces for generator and generated surfaces of pinion and gear.

Litvin, F. L.↗
DOE OSTI2023

FFTX-IRIS: Towards Performance Portability and Heterogeneity for SPIRAL Generated Code

FFTX-IRIS is a dynamic system to efficiently utilize novel heterogeneous platforms. This system links two next-generation frameworks, FFTX and IRIS, to navigate the complexity of different hardware architectures. FFTX provides a runtime code generation framework for high-performance Fast Fourier Transform kernels. IRIS runtime provides portability and multi-device heterogeneity, allowing computation on any available compute resource. Together, FFTX-IRIS enables code generation, seamless portability, and performance without user involvement. We show the design of the FFTX-IRIS system along with an evaluation of various small FFT benchmarks. We also demonstrate multi-device heterogeneity of FFTX-IRIS with a larger stencil application.

Rao, Sanil↗
NASA NTRS2016

Plasma Generator Using Spiral Conductors

A plasma generator includes a pair of identical spiraled electrical conductors separated by dielectric material. Both spiraled conductors have inductance and capacitance wherein, in the presence of a time-varying electromagnetic field, the spiraled conductors resonate to generate a harmonic electromagnetic field response. The spiraled conductors lie in parallel planes and partially overlap one another in a direction perpendicular to the parallel planes. The geometric centers of the spiraled conductors define endpoints of a line that is non-perpendicular with respect to the parallel planes. A voltage source coupled across the spiraled conductors applies a voltage sufficient to generate a plasma in at least a portion of the dielectric material.

Szatkowski, George N.↗
NASA NTRS1987

Method for generation of spiral bevel gears with conjugate gear tooth surfaces

A method for generation of spiral bevel gears is proposed that provides conjugate gear tooth surfaces. This method is based on a new principle for the performance of parallel motion of a straight line that slides along two mating ellipses with related dimensions and parameters of orientation. The parallel motion of the straight line, that is, the contact normal, is performed parallel to the line which passes through the foci of symmetry of the related ellipses. The manufacturing of gears can be performed with the existing Gleason's equipment.

Litvin, F. L.↗
NASA NTRS1987

Generation of spiral bevel gears with conjugate tooth surfaces and tooth contact analysis

A new method for generation of spiral bevel gears is proposed. The main features of this method are as follows: (1) the gear tooth surfaces are conjugated and can transform rotation with zero transmission errors; (2) the tooth bearing contact is localized; (3) the center of the instantaneous contact ellipse moves in a plane that has a fixed orientation; (4) the contact normal performs in the process of meshing a parallel motion; (5) the motion of the contact ellipse provides improved conditions of lubrication; and (6) the gears can be manufactured by use of Gleason's equipment.

Litvin, Faydor L.↗
NASA NTRS1985

Generation of spiral bevel gears with zero kinematical errors and computer aided simulation of their meshing and contact

There is proposed a method for generation of Gleason's spiral bevel gears which provides the following properties of meshing and contact: (1) the contact normal keeps its original direction within the neighborhood of the main contact point; (2) the contact ellipse moves along the gear tooth surface; and (3) the kinematical errors caused by Gleason's method of cutting are almost zero. Computer programs for the simulation of meshing and bearing contact are developed.

Litvin, F. L.↗
NASA NTRS1971

Millimeter-wave generation with spiraling electron beams

The feasibility of using the interaction between a thin, solid, spiraling electron beam of 10 to 20 kV energy and a microwave cavity to generate watts of CW millimeter-wave power was investigated. Experimental results are given for several prototype devices operating at 9.4 GHz and at 94 GHz. Power outputs of 5 W, and electronic efficiencies near 3%, were obtained at X band, and moderate gain was obtained at 94 GHz. The small-signal theory gives a good fit to the X-band data, and the device behavior at 94 GHz is as expected from the given beam characteristics. The performance is limited chiefly by the velocity spread in the spiraling electron beam, and once this can be brought under control, high-power generation of millimeter waves appears quite feasible with this type of device.

Kulke, B.↗
DOE OSTI2022

The Origin of the Doppler Flip in HD 100546: A Large-scale Spiral Arm Generated by an Inner Binary Companion

Companions at subarcsecond separation from young stars are difficult to image. However, their presence can be inferred from the perturbations they create in the dust and gas of protoplanetary disks. Here we present a new interpretation of SPHERE polarized observations that reveal the previously detected inner spiral in the disk of HD 100546. The spiral coincides with a newly detected 12 CO inner spiral and the previously reported CO emission Doppler flip, which has been interpreted as the signature of an embedded protoplanet. Comparisons with hydrodynamical models indicate that this Doppler flip is instead the kinematic counterpart of the spiral, which is likely generated by an inner companion inside the disk cavity.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS1972

Limitations on millimeter-wave power generation with spiraling electron beams.

A study is made of the suitability of the interaction between a thin, solid, spiraling electron beam of 5-15-kV energy and a microwave cavity, for the purpose of generating watts of CW millimeter-wave power. The effect of finite energy spread in the electron beam is considered both theoretically and experimentally. Measured results are given for a prototype device operating at 9.4 GHz. Power outputs of 5 W and electronic efficiencies near 2% have been obtained. The data agree well with the theory, subject to some ambiguity in the energy-distribution parameters. The performance is strongly limited by the energy spread in the beam.

Kulke, B.↗
NASA NTRS1989

Generation Method Improves Spiral Bevel Gears

Conjugate tooth surfaces reduce kinematic errors. Method for generation of spiral bevel gears provides conjugated gear-tooth surfaces and improved bearing contact. Conjugated surfaces preferable because maintain constant gear ratios during tooth-contact cycles. Changing gear ratios of nonconjugated surfaces give rise to kinematical errors in transfer of motion from driving gears to driven gears. Errors major sources of noise in power transmissions. Computer program developed to simulate cutting and meshing processes for pinions and gears to minimize kinematical errors.

Litvin, Faydor L.↗
DOE OSTI2020

Involute Working Group – Validation of CFD Turbulence Models for Steady-State Safety Analysis

There are three research reactors in the world having fuel plates curved as circle-involute (a spiral generated around a circle): The Oak Ridge National Laboratory (ORNL) High Flux Isotope Reactor (HFIR) located in Tennessee, U.S.A. [ORNL, 2018]; The Laue-Langevin Institute (ILL) High Flux Reactor (RHF) located in Grenoble, France [ILL, 2018]; and, The Technical University of Munich (TUM) Research Neutron Source Heinz Maier-Leibnitz (FRM II) located in Garching, Germany [TUM, 2018]. All three reactors are currently using Highly Enriched Uranium (HEU, 235U/U ≥ 20 wt. %) as fuel and all three are actively engaged in activities to convert to Low Enriched Uranium (LEU, 235U/U < 20 wt. %) fuel. More information on these reactors can be found in Section two. For various reasons, these reactors have expressed interest in using Computational Fluid Dynamics (CFD) tools to perform their Steady-State Thermal-Hydraulic (SSTH) safety calculations. Using CFD tools for SSTH analysis represents generally a significant departure from traditional methods and requires thorough verification and validation (V&V) to be accepted by regulators. This is why Argonne National Laboratory (ANL) and the involute reactors formed an informal group to help each other in this endeavor. This so-called Involute Working Group (IWG) aims at supporting the qualification of CFD tools for SSTH safety calculations. Activities include benchmarking, code-to-code comparison, Verification and Validation (V&V) as well as technical support. More information on the IWG and the reasons why involute-plate reactors are interested in CFD can be found in Section three. The present study aims at testing three turbulence models commonly implemented in commercial software (namely K-Epsilon, K-Omega and Reynolds-Stress) and assessing their relevance for involute-plate reactor application. An experiment performed by Gambill and Bundy in 1961 was performed to measure heat transfer coefficients in conditions prototypic of the HFIR reactor [Gambill, 1961]. More details on this experiment are provided in Section four. Based on the information available, CFD models of this experiment have been created and the experimental results have been compared to the ones obtained with these CFD models. CFD models and the results of this comparison are provided in Section five.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2021

Involute Working Group – Validation of CFD Turbulence Models for Steady-State Safety Analysis of Corner Geometry

Worldwide, three research reactors have fuel plates curved as a circle-involute (a spiral generated around a circle): Oak Ridge National Laboratory High Flux Isotope Reactor located in Tennessee, U.S.A. [1], Institut Laue-Langevin High Flux Reactor located in Grenoble, France [2], and Technical University of Munich Research Neutron Source Heinz Maier-Leibnitz located in Garching, Germany [3]. All three reactors are currently using highly enriched uranium ( 235 U/U ≥ 20 wt%) as fuel, and all three are actively engaged in activities to convert to low-enriched uranium ( 235 U/U < 20 wt%) fuel.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
NASA NTRS2002

Elliptic Grid Generation of Spiral-Bevel Pinion Gear Typical of OH-58 Helicopter Transmission

This paper discusses the source term treatment in the numerical solution of elliptic partial differential equations for an interior grid generation problem in generalized curvilinear coordinates. The geometry considered is that of a planar cross-section of a generic spiral-bevel gear tooth typical of a pinion in the OH-58 helicopter transmission. The source terms used are appropriate for an interior grid domain where all the boundaries are prescribed via a combination of Dirichlet and Neumann boundary conditions. New constraints based on the Green's Theorem are derived which uniquely determine the coefficients in the source terms. These constraints are designed for boundary clustered grids where gradients in physical quantities need to be resolved adequately. However, it is seen that the present formulation works satisfactorily for mild clustering also. Thus, a fully automated elliptic grid generation technique is made possible where there is no need for a parametric study of these parameters since the new relations fix these free parameters uniquely.

Kaul, Upender K.↗