Search NASA⌕ Search

SEARCH · Search NASA

Results for “spray manufacturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Spray Manufacturing Thermal Insulation Composites

Cellulose-based thermal insulation materials present significant potential for modern green building applications due to their inherent carbon sequestration properties. However, traditional manufacturing of composites often results in the limited thermal insulation performance and embodied carbon footprint due to an increased density from material shrinkage and higher energy consumption during the water-based slurry drying process. Here, we report solvent spraying coupled with dry powder feedstock to manufacture highly porous silica/straw insulation composites. The manufactured composite exhibits negligible shrinkage with the density of 0.08 g/cm 3 , thermal conductivity of 27.8 mW/(m·K), flexural modulus of 3.1 MPa, and compressive modulus of 0.89 MPa. Additionally, the prepared composite demonstrates fire retardancy (burning rate of 0.5 mm/min) and recyclability (99%). Furthermore, this solvent-spraying strategy opens up opportunities of energy-efficient insulation materials for carbon-sequestration building sectors.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Geometrical effects on the measured neutron residual stress in additively manufactured cold spray AA6061

Aluminum cold spray additive builds were made with varying wall widths and geometries to explore the effects of build geometry on residual stress development in the additively sprayed material. Deposition rates of over 750 g/hr were achieved without any cracking or delamination of the additively manufactured components. Neutron residual stress measurements revealed a maximum tensile residual stress of 41 MPa at the interface of the substrate and a maximum compressive residual stress of −35 MPa in the cold sprayed material. While there was not found to be significant residual stress changes between the cold sprayed walls, the cold sprayed cylinder had varying residual stress throughout the diameter with the outer diameter having a higher tensile residual stress than the interior. The low residual stress and minimal geometrical dependency demonstrate further part size is possible without concerns for component failure in AA6061. The application of common coating residual stress models to full scale additive builds is evaluated and discussed. The lack of residual stress evolution was studied by in-situ coating property measurement that revealed that the deposition stress of the AA6061 sprays reduced with increased layer thickness. In conclusion, this study provides insight into the evolution of residual stress in cold spray additive components and how both the mechanics and material responses differ from coatings.

Additive manufacturing↗
DOE OSTI2026

Scalable High-Throughput Open-Air Spray-Plasma Manufacturing of Solid-State Lithium Batteries

This final technical report presents a comprehensive analysis of a novel plasma-based in-line manufacturing process for large-area, LLZO-separator-based, solid-state lithium-ion batteries, demonstrating both technical feasibility and economic advantages over conventional vacuum deposition methods. The technical validation shows that spray-deposition with plasma curing achieves comparable electrode and separator quality to vacuum techniques while enabling continuous processing of components and industrially relevant film areas. Critical material interfaces maintain low porosity and high ionic conductivities, which confirm the process's ability to overcome the primary limitation of conventional methods - the trade-off between deposition quality and economically-viable production scale.

25 ENERGY STORAGE↗
DOE OSTI2023

Cast or Additively Manufactured Coils with End Turn Enhanced Heat Transfer Surfaces for Spray or Jet Cooling

Cast or additively manufactured coils present a new opportunity for creativity in thermal management of electric machines. Improvements to the heat transfer of spray or jet cooling of coil end turns through the incorporation of pins or enhanced heat transfer surfaces in the cast end turn surfaces is explored. The thermal response of cast copper half-turns is measured for a range of spray/jet volumetric flow rates and ohmic loss heat fluxes. A significant reduction, ~30%, in the steady state temperature and increased spray cooling heat transfer coefficients was experimentally measured when the pins or enhanced heat transfer surfaces are incorporated.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

Mechanical and Tribological Performance of Additively Manufactured Nanocrystalline Aluminum via Cryomilling and Cold Spray

In this study, nanocrystalline (NC) aluminum (Al) and magnesium (Mg)-doped Al bulk components were fabricated using a hybrid manufacturing process that combines cryomilling and high-pressure cold spray (HPCS) additive deposition techniques. Yttria-stabilized zirconia (YSZ) was also added during the HPCS process to improve deposition efficiency and build-up thickness via peening. The evolution of morphology, crystallite size, and elemental composition of both cryomilled powders and cold-sprayed (CS’ed) components was systematically characterized using X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and Transmission Electron Microscopy (TEM). Mechanical characterization was performed using Vickers microhardness and uniaxial tensile testing, while the tribological behavior was assessed using sliding wear tests under dry/lubricated conditions. XRD analysis revealed that increased cryomilling duration led to significant crystallite refinement, which directly correlated with enhanced hardness and strength. This mechanical strengthening was accompanied by an increase in coefficient of friction (COF) and lower wear rates. The results also showed that the Mg-doped Al exhibited superior hardness, tensile strength, and tribological performance compared to pure Al. The study further explores the underlying mechanisms responsible for these enhancements, highlighting the potential of solute-assisted grain boundary stabilization in tailoring high-performance NC Al alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Manufacturing Oxide Dispersion Strengthened (ODS) steel plate via cold spray and friction stir processing

Oxide dispersion strengthened (ODS) steels, traditionally fabricated by ball milling and conventional powder metallurgy techniques to achieve bulk form, followed by intricate rolling and thermal treatment steps to achieve plate or sheet form. Here, we present a novel processing route that combines cold spray (CS) with friction stir processing (FSP) to manufacture ODS steel plate directly from gas atomization reaction synthesis (GARS)-prepared powder, thus no rolling steps involved. Microstructural and mechanical characterizations were performed to assess the quality and properties of the resulting ODS steel plate. Our findings demonstrate that the slightly porous CS deposited layer was fully consolidated after FSP, yielding a fully dense ODS steel plate that exhibited a favorable tradeoff between strength and ductility upon extraction from the substrate. Furthermore, through microstructural analysis, we revealed the presence of an appreciable density (∼10 22 /m 3 ) of nano-sized oxide particles, with the majority being smaller than 5 nm via the combined CS + FSP fabrication route. This work serves as a first proof-of-concept demonstration of the manufacturing approach described herein, offering a possible alternative route for producing ODS steel plates.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Smart manufacturing approach to manufacture bulk nanocrystalline aluminum for lightweight applications

In this research, a smart manufacturing approach was used to enhance the mechanical properties of aluminum (Al) for lightweight applications. The smart manufacturing involved cryomilling of Al powders with and without 5 wt.% magnesium (Mg) powders for varying durations followed by a high-pressure cold spray (HPCS) additive manufacturing process to prepare bulk components. The morphological changes, crystallite size, and composition of the cryomilled powders and cold sprayed (CS’ed) components were examined using scanning electron microscopy (SEM), x-ray diffraction (XRD), and transmission electron microscopy (TEM) techniques. The results showed that the crystallite size reduces with an increase in cryomilling time and the addition of Mg dopant. To test the mechanical properties of the bulk CS’ed components, microhardness tests were performed using a Vickers microhardness tester. Uniaxial tensile tests were also carried out to ascertain the material’s tensile properties. The mechanical testing results showed great improvement in the hardness and tensile strength of CS’ed Al–Mg samples as compared to pure Al samples. Subsequently, fractography analysis of the tensile failed samples was carried out to determine the nature of the failure. Here, the research article also discusses the inherent mechanisms for the improvement in mechanical properties of smart manufactured components as a result of Mg doping and cryomilling.

36 MATERIALS SCIENCE↗
DOE OSTI2024

The Grain Boundary Relaxation (GBR) Approach for Manufacturing High Strength Nanocrystalline Lightweight Metals

The overarching goal of the project was to conduct research and development work as proposed in the Statement of Project Objective (SOPO) of the award document DE-FE-0009116. The project had 4 tasks and 12 milestones. All the milestone deliverables were completed. The accomplishments of the project objectives and technical discussions are described in Sections 3 and 4, respectively. The modeling and simulation work indicated that to increase the strength and stability of nanocrystalline aluminum (Al), selection of dopants, such as Mg, is necessary. It was predicted that the crystallite size should be less than 50 nm to give high strength. On the basis of modeling, cryo-milling of Al was conducted with the addition of Mg as a function of different times. The crystallite size of the cryo-milled powders was determined by XRD and TEM. Both measurements showed that the actual crystallite size of the grain was <40 nm. The thermal stability of the grain size was established as a function of temperature. It was established that the grain size was < 50 nm up to 500C. The crystallite size of the bulk sample prepared by spark plasma sintering (SPS) and cold spray (CS) additive manufacturing was less than <40 nm. The mechanical properties of the bulk samples prepared by SPS and CS, showed excellent microhardness, good tensile properties (>200 MPa) with moderate ductility and improved fatigue performance. Adding yttria stabilized zirconia (YSZ) improved the build thick of the CS sample, however the YSZ was getting embedded into the sample. A highly dense SPS samples sent for 3rd party testing to the Innovation Testing Services showed a minimum hardness of 180 HV with an average tensile strength of 512.5 MPa. The high cycle fatigue tests also showed an endurance limit of 179.5 MPa. The Energy cost evaluations showed an overall energy cost of around $\$$17.05 for the cryomilling and SPS processes and the total manufacturing cost calculations of $\$$78.14 for 1 kg of sample. The energy cost to prepare a Kg of CS sample is $\$$17.60 and the overall manufacturing cost is $\$$86.85.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Filament Extension Atomization for High Solids Loading in Energy Efficient Spray Drying Systems

We demonstrate that we could scale FEA to reach outputs needed by industrial production, while increasing solids loading of the sprayed product by at least 30% and maintaining equal or better spray powder. After testing a wide range of products, in collaboration with industry partners we decided on our primary spray products of dry whey and WPC-80, two common materials processed and sold by US manufacturers with different parameters. We sprayed these with FEA at solids loadings of 70% for dry whey and 45% for WPC-80 with a spray output with particle sizes similar to industrial particles sizes and reduced variation in particle size. We simultaneously scaled up FEA first with a multi-nip with 6 nips surrounding a central roller with parallel axis of rotation and eventually with a tapered design that solved problems we encountered with our initial design. We were able to achieve output from a single array from our first design of up to 4.7 liters per minute (L/min) and from an array of our second multi-nip of 8 L/min exceeding expectations. This demonstrates that FEA technology can indeed be scaled up to meet the needs of industrial production. More arrays can be added as necessary to meet a wide range of spray dryer designs. We also tested FEA to create dried powders from a small scale (10 L/hour of water removal) spray dryer. Though we were not able to produce large quantities of powder from FEA due to challenges in integration, the powder we produced was higher quality and produced from higher solids loading materials. From our technoeconomic analysis we for a typically sized spray dryer, we estimate a 27% cost reduction and 41% energy and carbon reduction for WPC-80 and a 39-57% cost reduction and 52-76% energy reduction for sweet dry whey (depending on the exact product).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

Melt compounding of spray-dried cellulose nanofibrils/polypropylene and their application in 3D printing

Abstract Micro- and nano-scale cellulosic fillers exhibit excellent dispersion and distribution within a thermoplastic matrix during the process of melt compounding or injection molding. In this study, spray-dried cellulose nanofiber (SDCNF) powders were manufactured using a pilot-scale rotating disk atomizer spray dryer. Bleached Kraft pulp (BKP), unbleached Kraft pulp (UKP), and old corrugated cardboard pulp (OCC) fibrillated at a fines level of 90% were used as feedstock materials for spray-drying. BKP-, UKP-, and OCC- SDCNFs were compounded with polypropylene using a twin screw co-rotating extruder. Maleic anhydride grafted polypropylene (MAPP) was used as a coupling agent in the composite formulations. The tensile, flexural, and impact properties of SDCNF-filled PP composites increased at 10 wt% SDCNF loading. The presence of SDCNFs in the PP matrix resulted in faster crystallization and a 12% reduction in the degree of crystallinity of the neat PP. The coefficient of thermal expansion (CTE) of neat PP was reduced by up to 31% attributable to the presence of the SDCNFs. Application of the SDCNF-reinforced PP composites in 3D printing reduced the shrinkage rate of the printed neat PP by 39%, and the printability of the PP was significantly improved with the addition of the SDCNFs.

Materials Science↗
DOE OSTI2025

Eutectic melting of alloy microparticles upon low velocity impact

Although impact melting has been quantified in a number of pure metals, alloyed microparticles have access to low melting-point eutectics that can promote earlier melting. Through real-time monitoring of single particle impacts resolved at the nanosecond- and micron-scales, we explore the impact melting of AA7075 from high velocities, where it is abundant and clear, to velocities as low as ∼269 m/s. Here, by using a hard substrate to isolate the deformation largely to the particle, we show that the adiabatic heat produced by the plasticity of the impact can explain the onset of melting at low velocity.

Additive manufacturing↗
DOE OSTI2025

Assessment of Benefits of Solid-State Advanced Manufacturing Processes for Nuclear Energy Products

The Advanced Materials and Manufacturing Technology (AMMT) program develops cross cutting technologies in support of a broad range of nuclear reactor technologies and maintains U.S. leadership in materials and manufacturing technologies for nuclear energy applications. This overall project provides the U.S. Department of Energy a critical feasibility study comparison of three solid-state processes to other AM processes, thereby providing the feasibility of the solid-state processes examined to manufacture 316H SS and ODS steel components: • Fused-filament fabrication (FFF): This work provides an initial evaluation of the impact of powder morphology and sizes on the FFF process, and the feasibility and adaptability for different material systems, to use FFF for ODS steels and 316 SS. • Shear-assisted processing and extrusion (ShAPE): Specifically for this portion of the project on ShAPE tube forming, the objectives will be to determine the feasibility to direct tube forming of high tensile strength steel tubing, specifically for ODS steel to determine the effect of the patented extrusion process on the dispersoids of the ODS material. Additionally, as often ODS powders are mechanically alloyed and therefore more platelike or angular, this feasibility was to explore the impact on the optimization process and initial feasibility of direct tube forming. • Cold spray and friction stir additive manufacturing as a stretch goal: Bulk and near net shape manufacturing processes for high-temperature, high-strength alloys are needed. Additionally, cold spray techniques can be applied in-situ at the operational level for repair and can provide multiple benefits to the nuclear industry. These tasks aim to provide information to show benefits of cold spray during the full life cycle, namely research and development, product manufacturing, and repair to mention a few key points.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

Automation of Solid Oxyde Electrolyzer Cell (SOEC) & Stack Assembly

The work performed under this agreement before the No/Go decision amounted to the following: 1. Preliminary manufacturing requirements defined by business sensitivity, baseline processes & risk assessment; 2. Process & materials development, in-line gauge exploration, and preliminary automation work used to reduce risk & further refine equipment specifications; 3. “Request for Quote” issued to multiple suppliers for major equipment; 4. Application specific equipment, hardware, and fixturing will be more beneficial to fabricate inhouse; 5.Current proposals & estimates meet cycle time, capital spend, & direct labor; space is on target but requires awareness; 6. Team will continue to explore opportunities to reduce risk (dry time, traceability); 7. Go / No-Go, Purchase Orders, Equipment build & commissioning next All other future task were not completed because during the Go /No-Go decision it was confirmed this project was a "No-Go" and did not proceed past BP1; these included the following: 1. Preliminary manufacturing requirements defined by business sensitivity, baseline processes & risk assessment; 2. Process & materials development, in-line gauge exploration, and preliminary automation work used to reduce risk & further refine equipment specifications; 3. “Request for Quote” issued to multiple suppliers for major equipment; 4. Application specific equipment, hardware, and fixturing will be more beneficial to fabricate inhouse; 5. Current proposals & estimates meet cycle time, capital spend, & direct labor; space is on target but requires awareness; 6. Team will continue to explore opportunities to reduce risk (dry time, traceability) In final preparation of the termination of the Automation of Solid Oxyde Electrolyzer Cell (SOEC) & Stack Assembly, Cummins has purchased no equipment with government funds, and there is no government-owned property in Cummins possession related to this project. Minimal labor and travel were completed and paid. This acts as the Final technical report and concludes our business with DOE on this grant.

36 MATERIALS SCIENCE↗