Search NASA⌕ Search

SEARCH · Search NASA

Results for “spray measurements”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Quantitative near-field water–air spray measurements at elevated pressures by neutron radiography imaging

Extensive experimental research on high-pressure spray has been conducted for decades to deepen our understanding and optimize its use in transportation, aviation, and propulsion applications; however, the near-field and in-nozzle flow characteristics are not fully understood. Dense near-field spray is among the most challenging diagnostic tasks since light is severely scattered and diffused by the liquid droplets and columns. In this work, the near-field spray and in-nozzle flow characteristics of an aeration nozzle at elevated pressures were characterized by neutron radiography imaging at the Oak Ridge National Laboratory High Flux Isotope Reactor. Neutron imaging benefits via strong penetration depths for some metals (i.e., aluminum, lead, and steel) and is sufficiently sensitive to detection of light elements, especially for hydrogen-based molecules, due to the large incoherent scattering cross section of neutrons. Both two-dimensional snapshots of the near-field spray and a three-dimensional tomographic scan of the nozzle geometry and in-nozzle water were obtained. This work provides new quantitative characterization of practical metal nozzle geometry for accurate boundary conditions, internal flow patterns inside the nozzle, and high-pressure spray flows. In conclusion, the findings may be used to improve performance and operating conditions of transportation vehicles and propulsion systems.

42 ENGINEERING↗
DOE OSTI2024

Residual Stress in Cold Spray SS304L Measured Via Neutron Diffraction and Comparison of Analytical Models to Predict the Residual Stress

Here, this study employs neutron diffraction to investigate the relationship between residual stress and coating thickness in cold sprayed 304L austenitic stainless steel. Results show that shot peening predominantly impacts the residual stress profile, leading to substantial in-plane compressive force. The impact of laser heating, a widely used method to alter cold spray's microstructural properties, on the coating's residual stress is also analyzed. The findings indicate that the maximum compressive residual stress in the in-plane component is mainly independent of coating thickness, which suggests that the material properties determine the maximum residual stress. The cold sprayed deposits possessed compressive, nearly biaxial strain and stresses. After laser heating, these stresses were replaced by tensile residual stresses. Two analytical models, the Tsui and Clyne and the Boruah models, for predicting residual stresses are also evaluated, and both models provide reasonable fits to the experimental data. At this point, the deviations between the experimental results and the models are principally caused by the inability of the current models to address plastic deformation and relaxation, and the residual stresses generated by thermal gradients.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Development of limited-view tomography for measurement of Spray G plume direction and liquid volume fraction

Abstract The method for direct injection of fuel in the cylinder of an IC engines is important to high-efficiency and low-emission performance. Optical spray diagnostics plays an important role in understanding plume movement and interaction for multi-hole injectors, and providing baseline understanding used for computational optimization of fuel delivery. Traditional planar or line-of-sight diagnostics fail to capture the liquid distribution because of optical thickness concerns. This work proposes a high-speed (67 kHz) extinction imaging technique at various injector rotations coupled to computed tomography (CT) for time-resolved reconstruction of liquid volume fraction in three dimensions. The number of views selected and processing were based on synthetic (modeled) liquid volume fraction data where extinction and CT adequately reconstructed each plume. The exercise showed that for an 8-hole, symmetric-design injector (ECN Spray G), only three different views are enough to reproduce the direction of each plume, and particularly the mean plume direction. Therefore, the number of views was minimized for experiments to save expense. Measurements applying this limited-view technique confirm plume–plume variations also detected with mechanical patternation, while providing better spatial and temporal resolution than achieved previously. Uncertainties due to the limited view within pressurized spray chambers, the droplet size, and optically thick regions are discussed. Graphic abstract

42 ENGINEERING↗
DOE OSTI2025

Measurement of Spray Chamber Ignition Delay and Cetane Numbers for Aviation Turbine Fuels

Experiments using pure compounds, National Jet Fuels Combustion Program (NJFCP) test fuels, and commercial jet fuels were conducted to demonstrate the equivalence of the indicated cetane number (ICN) and derived cetane number (DCN) for jet fuels. The calibrated range for ICN was also extended to lower cetane number (CN) values (5 to 35) to allow CN quantification for jet fuel synthetic blending components (SBCs) with low CN. ICN and DCN were shown to be highly correlated for values above about 30. This study presents the most comprehensive comparison of these two methods published to date. Because of the importance of low-volume test methods for early-stage SBC production process development, we demonstrated that ICN and DCN can be accurately measured with 15 mL of fuel, well below 40 to 100 mL required by standard methods. ICN or DCN is important for jet fuels because fuels with lower CN are more prone to lean blowout (LBO), an undesirable operational failure in a jet engine. Comparing data on a fuel-to-air ratio (Φ) at LBO for the NJFCP fuels shows similar linear correlations for ICN and DCN. Ignition delay measurements at lower-pressure and higher-temperature conditions may be more directly relevant to LBO. At 675 °C, 0.5 MPa, and a global Φ of roughly 0.68, ignition delay time correlations to LBO were similar to those produced from DCN and ICN. A much weaker correlation was obtained with a global Φ value of 0.34.

09 BIOMASS FUELS↗
DOE OSTI2023

A physics-driven Σ-Y atomization model for heavy-duty engine simulations

The atomization of a liquid jet is a multi-scale and multi-physics problem of interest for many engineering applications. Particularly, it drives the fuel-oxidizer mixing and dictates the efficiency of combustion engines. High-fidelity multi-phase simulations remain challenging due to the excessive computational cost required to capture all the atomization scales. Thus, atomization models are necessary to represent sub-grid liquid structures. Here, in this work, a modified Σ-Y model in the context of Eulerian-Lagrangian Spray Atomization (ELSA) is used to transport the surface area density of the spray. The model's predictive performance is assessed under various operating conditions relevant to heavy-duty engines using the Engine Combustion Network (ECN) Spray C and Spray D research-grade injectors. The classic droplet collision formulation of the Σ-Y model alone does not replicate the response of the measured spray surface area to changes in injector, ambient pressure, and injection pressure, requiring individual tuning of the model's parameters. Instead, a transition between dense and dilute spray breakup mechanisms is proposed in terms of the average droplet spacing. The collision breakup mechanism represents the dilute spray, whereas the droplet size in the dense spray is driven by a competition between the integral scale of turbulence and the balance between the turbulent kinetic energy and the surface energy of the droplets. Such an approach minimizes the requirements for model tuning. Moreover, the role of the constants of a compressible standard k-ε RANS model is assessed in the injector's internal flow and external spray simulation framework, and an updated set is proposed. The results are validated against x-ray radiography and Ultra-Small Angle X-ray Scattering (USAXS) data and highlight the predictive capabilities of the proposed physics-driven Σ-Y model, which is compatible with engine simulation turnaround times.

42 ENGINEERING↗
DOE OSTI2021

Image processing methods for Rayleigh scattering measurements of diesel spray mixing at high repetition rate

This work describes the diagnostic implementation and image processing methods to quantitatively measure diesel spray mixing injected into a high-pressure, high-temperature environment. We used a high-repetition-rate pulse-burst laser developed in-house, a high-speed CMOS camera, and optimized the optical configuration to capture Rayleigh scattering images of the vaporized fuel jets inside a constant volume chamber. The experimental installation was modified to reduce reflections and flare levels to maximize the images’ signal-to-noise ratios by anti-reflection coatings on windows and surfaces, as well as series of optical baffles. Because of the specificities of the high-speed system, several image processing techniques had to be developed and implemented to provide quantitative fuel concentration measurements. We find that these methods involve various correction procedures such as camera linearity, laser intensity fluctuation, dynamic background flare, as well as beam-steering effects. Image inpainting was also applied to correct the Rayleigh scattering signal from large scatterers (e.g. particulates). The experiments demonstrate that applying planar laser Rayleigh scattering at high repetition rate to quantitatively resolve the mixing of fuel and ambient gases in diesel jets is challenging, but possible. The thorough analysis of the experimental uncertainty and comparisons to past data prove that such measurements can be accurate, whilst providing valuable information about the mixing processes of high-pressure diesel jets.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

Fuel reid vapor pressure level and ethanol content on stochastic preignition, effects at steady and unsteady engine operation

The present work investigates relations between fuel Reid vapor pressure (RVP) and biofuel (ethanol) content on stochastic preignition (SPI) at both sustained steady-state engine operation and following load transients. This work stems from in-field observations that automotive original equipment manufacturers have observed consistent seasonal increases in United States customer drivability complaints and warranty claims during September and October where SPI is suspected to be responsible. The seasonal timing of these events coincides with the United States seasonal fuel property changeover initiating on September 15 each year, where fuel RVP increases. To explore potential linkage between fuel RVP and SPI the present study employs engine SPI experiments coupled with laboratory spray measurements of fuels with RVPs of 8, 12, and 16 psi in both E10 (10% ethanol) and E25 (25% ethanol) fuels. Engine results are partitioned into fuel RVP and ethanol content effects on SPI in steady-state, sustained high-load engine operation and unsteady-state low- to high-load transitions, where off-engine spray vessel patternation and tip penetration results help to elucidate the observed fuel effects on SPI. A boosted direct-injected, spark-ignition engine was fueled with three market relevant E10 and E25 fuels with RVPs of 8, 12, and 16 to characterize the interplay between winter fuels and abnormal combustion behavior. The steady-state work shows that for high-load, steady-state engine operation, SPI is directly linked to fuel retention, which was found to be dependent on fuel distillation. The unsteady-state engine operation work shows that following low-to high-load transitions, SPI can occur from a memory of fuel property effects at low-load operation. Specifically, the fuel RVP effect on fuel spray collapse at low loads was found to correlate with SPI with a more than 95% confidence interval following low- to high-engine-load transitions. Results suggest that fuel-wall impingement at low-load operation could carry over into high-load transitions and generate SPI events following low- to high-load transitions.

09 BIOMASS FUELS↗
DOE OSTI2022

Beam Spray Thresholds in ICF-Relevant Plasmas

Beam spray measurements suggest thresholds that are a factor of ≈2 to 15× less than expected based on the filamentation figure of merit often quoted in the literature. In this moderate-intensity regime, the relevant mechanism is forward stimulated Brillouin scattering (FSBS). Both weak ion acoustic wave damping and thermal enhancement of ion acoustic waves contribute to the low thresholds. FSBS imparts a redshift to the transmitted beam. Here, regarding the specific possibility of beam spray occurring outside the laser entrance holes of an indirectly driven hohlraum, this shift may be the most concerning feature owing to the high sensitivity of crossed-beam energy transfer to the interacting beam wavelengths in the subsequent overlap region.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Transmitted wave measurements in cold sprayed materials under dynamic compression

Spray-formed materials have complex microstructures which pose challenges for microscale and mesoscale modeling. To constrain these models, experimental measurements of wave profiles when subjecting the material to dynamic compression are necessary. The use of a gas gun to launch a shock into a material is a traditional method to understand wave propagation and provide information of time-dependent stress variations due to complex microstructures. This data contains information on wave reverberations within a material and provides a boundary condition for simulation. Here we present measurements of the wavespeed and wave profile at the rear surface of tantalum, niobium, and a tantalum/niobium blend subjected to plate impact. Measurements of the Hugoniot elastic limit are compared to previous work and wavespeeds are compared to longitudinal sound velocity measurements to examine wave damping due to the porous microstructure.

36 MATERIALS SCIENCE↗
DOE OSTI2021

X-Ray Radiography and Phase-Contrast Imaging of the Engine Combustion Network Spray B Sprays and Injection

X-ray measurements of diesel sprays from two of the Engine Combustion Network (ECN) Spray B injectors are described. Measurements in these three-hole nozzles complement both visible light measurements of these sprays and previous x-ray measurements of the axial single-hole ECN Spray A injectors. Both axial and lateral motions of the injector needle valve were measured with x-ray phase contrast imaging. Additionally, the liquid mass distribution in room temperature sprays at elevated ambient pressure was determined with x-ray radiography. Measurements of both needle valve motion and spray distribution were performed at both the standard Spray A/B conditions and with selected variations of injection pressure, ambient density, and injection timing. The needle valve motion for the Spray B injectors is quite similar to that of the Spray A injectors, though little lateral motion is seen in either Spray B injector. Compared to the sprays from the Spray A injectors, the sprays from Spray B penetrate more slowly in the near-nozzle region, demonstrate a broader, more uniform distribution in the transverse direction, and are significantly more variable with respect to time. These differences demonstrate the importance of studies with multi-hole nozzles to provide insight into applied diesel combustion.

42 ENGINEERING↗
DOE OSTI2025

Sea spray aerosol production flux retrieval based on Doppler lidar measurements

Supermicron sea spray aerosols (SSA) play a crucial role in stratocumulus cloud microphysics and drizzle formation. However, our understanding of SSA's spatiotemporal distribution, production mechanisms, and fluxes in the marine boundary layer remains limited. This study introduces a novel approach to determine supermicron SSA production flux and number concentration at various heights above the ocean surface. Our method leverages Doppler lidar data, specifically attenuated backscatter and vertical velocity, collected at a 105 m range gate during the Eastern Pacific Clouds and Aerosols for Precipitation Experiment (EPCAPE) at Scripps Pier, La Jolla, California. To focus on nascent SSA, we analyzed data from periods with wind directions between 225° and 315° and wind speeds exceeding 4 m s −1 . Cloud and precipitation events were excluded using relative humidity, backscatter thresholds, and 2D Video Disdrometer observations. Results show that calculated supermicron SSA number concentrations at 105 m ranged from 0.26 to 2.93 cm −3 for surface wind speeds between 4 and 6 ms −1 . When exceeding the method's Limit of Detection, estimated production fluxes ranged from 0.20 to 1.53 cm −2 s −1 . This methodology has potential for application in various oceanic locations, likely enhancing our understanding of SSA's role in atmospheric processes and climate interactions.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Residual stress of controlled atmosphere plasma spray blended metal deposits measured via in-situ substrate curvature method

The preliminary use of the in-situ curvature measurement technique for analyzing the planar stress evolution of controlled atmosphere plasma spray (CAPS) refractory metal deposits was performed with SNL-NM org. 1834’s CAPS system. A porous refractory metal exemplar of Ta-Nb was sprayed onto Ni-200, Ti-6Al-4V, and Al 7075-T6 substrates using a constant plasma torch parameter setting and deposition toolpath. Residual stresses of the deposits were found to be largely influenced by the substrate coefficient of thermal expansion and were calculated to be 49, 90, and -136 MPa for Ni 200, Ti-6Al-4V, and Al 7075-T6, respectively. The “Evolving stress” of the Ta-Nb deposits, which more accurately describes the mean intrinsic splat quenching stress of the spray material during deposition, was calculated to be 67, 92, and 129 MPa for Ni-200, Ti-6Al-4V, and Al 7075-T6, respectively. Notable difference in curvature measurement for the 1st coating pass for the Al 7075- T6 substrate was observed, with interface micrograph evidence suggesting potential softening and/or melting of the Al 7075-T6 substrate surface during deposition. Substrate temperature measurements prior to Ta-Nb deposition were used to calculate thermal energy absorbed from the hot gas plume by the different substrates and were found to correlate to the substrate’s thermal effusively. These calculated thermal energies were also found to be ~10 to 15% of the calculated energy output from the plasma torch’s nozzle exit for these experimental conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Spontaneous Raman–LIF–CO–OH measurements of species concentration in turbulent spray flames

This paper presents new measurements of species concentrations, temperature and mixture fraction in selected regions of a turbulent ethanol spray flame. The line-Raman–LIF–COsingle bondOH setup developed at the Sandia's Combustion Research Facility is utilised to probe regions of a spray flame where laser breakdown of liquid droplets is avoided and the remaining interferences can be corrected. The spray flame is stabilised on the piloted Sydney needle spray burner, where axial translation of the liquid injecting needle in the air-blast stream can transition the spray from dilute to dense. The solution to obtaining successful measurements is found to be multifaceted and includes: the appropriate selection of flame conditions; high sensitivity of the Raman detection system permitting reduced laser energies; development of a pre-processing algorithm to reject strong droplet interferences; and application of the hybrid matrix inversion method combined with wavelet denoising to account for interference corrections and noise at the very low signal levels obtained. Unique and necessary for the successful measurements reported in this paper, a pre-processing algorithm is outlined that removes data points corrupted with strong interferences from droplets. These interferences arise from a range of sources, but the most intense are due to the laser interaction with surrounding mist or liquid fragments, such that measurements near the jet centreline are corrupted and hence discarded. Reliable measurements of mixture fraction, temperature obtained from the sum of the species number densities, and species mole fractions are reported for regions in the flames sufficiently far from the centreline. The paper demonstrates the feasibility of the judicious use of Raman scattering in turbulent spray flames, the results of which will be extremely useful for validating numerical simulations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Bio-fuel effects and seasonal fuel property variations related to abnormal combustion occurrences observed in the field

Since 2015, the automotive industry has regularly observed sharp increases in customer complaints of poor driveability and increased warranty claims during the months of September and October. These persistent seasonal complaint increases have been tracked to occur from increased abnormal combustion events that coincide with the seasonal transition from summer to winter fuel volatility, beginning on September 15th annually. The Reid Vapor Pressure (RVP) of gasoline during this seasonal transition has been found to be the primary property attributed to this annual issue. It’s hypothesized that an increase in volatile butanes and pentanes from advanced petroleum recovery techniques and hydrofracking production has hastened the transition from summer to winter fuel volatility in the marketplace, rather than the gradual increase of the RVP over time as historically intended. At worst, mid-winter fuel, with an RVP ranging from 12 to 16 psi, depending on location in the U.S., enters the market while ambient temperatures can still be above average for the winter season. This combination of high volatility fuel with unseasonably warm weather will increase fuel system flash boiling, injector spray cavitation, and spray collapse inside the engine’s combustion chamber, ultimately linking fuel property variations to abnormal engine combustion processes. This CRADA program will investigate these known knowledge gaps by coupling with two national laboratories, Oak Ridge National Laboratory, and the National Renewable Energy Laboratory to employ both unique tools and expertise throughout the industry to provide the insight, knowledge, and data critical to understand the observed interactions. Overall findings of this work are that fuel wall retention increased SPI proportionally, and fuels with an increased distillation (i.e. energy fraction) above the wall temperature increased fuel retention. Likewise fuels with increased enthalpy of vaporization (HoV) increased fuel retention proportional to the temperature reduction from the HoV (~13K reduction in this work). Thus, fuel with increased HoV and increased fuel distillation above the linear temperature also exhibited increased SPI rates. Fuel with high RVP did exhibit increased fuel spray collapse form spray imaging measurements, but in SPI testing the high volatility of these fuels at the tested conditions did not necessarily increase SPI rates despite exhibiting increased spray collapse in injector imaging and increased spray-wall impingement measured in fired engine testing. It was also found that spray imaging showed collapse was possible at throttled conditions, but this was not relevant to high boost pressures relevant to SPI conditions, however, under transient load and or speed encountered in real-world operation fuel spray collapse could affect fuel retention and real-world SPI that were not probed in the automated high load test sequence of this work.

09 BIOMASS FUELS↗
DOE OSTI2023

Detailed mixing measurements from single-hole converging ECN injectors using Rayleigh scattering

Time resolved liquid and vapor fields of dodecane and oxymethylene ethers are measured from Spray A-3 and Spray D using high speed Rayleigh scattering and diffuse back illumination at the Engine Combustion Network (ECN) Spray A condition of 900 K and 22.8 kg/m 3 . Global quantities including mixture fraction, vapor and liquid penetration, as well as spreading angle are measured. The mixture fraction fields and vapor penetration profiles are well predicted by the 1-D Musculus-Kattke model. The mixture fraction field and vapor penetration from Spray A-3 are similar to those measured from Spray A in previous works. Spray D exhibits higher mixture fraction fields and vapor penetration due to its larger nozzle diameter. The quasi-steady mixture fraction fields from these injectors scale well when distance from the injector is normalized by the nozzle diameter. The turbulent dissipation structures were also analyzed based on the orientation, thickness, and magnitude of the mixing layers. Furthermore, the orientation and thickness are similar to other measurements in atmospheric gas jets, while the magnitude is lower. The thickness and magnitude are subject to uncertainties due to limitations in the imaging resolution of the system but still provide an order of magnitude as a useful reference for comparison against computational fluid dynamic simulations.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Computation of conventional and alternative jet fuel sensitivity to lean blowout

Large Eddy Simulations (LES) are performed to compute the sensitivity of a conventional (A-2) and an alternate bio-jet (C-1) fuel to Lean Blowout (LBO). A realistic aviation gas turbine engine combustor configuration is considered. Reliable experimental LBO data and OH* chemiluminescence data for the conventional and alternate jet fuel in the combustor configuration have recently become available. The present work utilizes a highly automated, on-the-fly meshing strategy, along with adaptive mesh refinement, to demonstrate the feasibility of capturing the realistic combustion processes. A Lagrangian framework, with initial conditions specified using measurements of spray statistics, is used to model the fuel spray. Newly developed compact reaction mechanisms based on fuel surrogates are validated for the A-2 and the C-1 fuels. The compact reaction mechanisms are implemented using a detailed finite rate chemistry solver. Spray statistics computed by the present LES simulations compare well with available measurements at stable flame conditions near the lean blowout limit. The computed shape of the stable flame as represented by line integrated OH concentrations compares well with the experimental OH* chemiluminescence data. Lean blowout is reached by gradually decreasing the fuel flow rate in the computations, similar to that in the experiments. The results of the LES simulations effectively capture the fuel composition effects and estimate the sensitivity of the LBO limits to the fuel type. The computed trends in LBO limits agree within engineering accuracy with the experimental results for conventional and alternative aviation fuels. The methodology for predicting the fuel composition effects on the lean blowout limits in a fully resolved realistic, complex combustor is established for the first time.

Adaptive mesh refinement↗