Search NASA⌕ Search

SEARCH · Search NASA

Results for “stagnation pressure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Geometric optimization of the supersonic stagnation-pressure probe

An investigation was conducted at Mach numbers of 1.41, 1.83, and 2.20 to determine the effects of parametric variations both in the height of the pitot-tube center line from the probe surface, by varying the pitot-tube diameter, and in the radius of surface curvature on the pressure recovery of a probe designed to measure free-stream stagnation pressure. The probe consists of a pitot tube mounted on the surface of a curved cylinder of circular cross section; the pitot tube senses the pressure of the stream tube which has been slowed to subsonic or near sonic velocity by isentropic compression along the curved surface. Pressure recovery - greater than or equal to 99.8 percent of free-stream stagnation pressure - was obtained for a wide range of both angle of attack and yaw for probes satisfying the optimum design criteria determined in this investigation.

Couch, L. M.↗
NASA NTRS1972

A stagnation pressure probe for use in supersonic flow

Probe was developed which is capable of recording true stagnation pressure in supersonic and subsonic flows. Static pressure orifices in the compression surface allow probe to be used as combined flow direction and stagnation pressure sensor.

Goodyer, M. J.↗
NASA NTRS1975

Effects of geometric variables on the performance of a probe for direct measurement of free-steam stagnation pressure in supersonic flow

An investigation was conducted at Mach numbers of 1.41, 1.83, and 2.20 to determine the effects of parametric variations in the height of the pitot-tube center line from the probe surface and in the radius of the surface curvature on the pressure recovery of a probe designed to measure the free-stream stagnation pressure. The probe consists of a pitot tube mounted on the surface of a curved cylinder of circular cross section. The pitot tube senses the pressure of the stream tube which has been slowed by isentropic compression along the curved surface. Pressure recovery, greater than or equal to 99.8 percent of the free-stream stagnation pressure, was obtained for a wide range both of angle of attack and of yaw for probes satisfying the predetermined optimum design criteria.

Couch, L. M.↗
NASA NTRS1992

Increase of stagnation pressure and enthalpy in shock tunnels

High stagnation pressures and enthalpies are required for the testing of aerospace vehicles such as aerospace planes, aeroassist vehicles, and reentry vehicles. Among the most useful ground test facilities for performing such tests are shock tunnels. With a given driver gas condition, the enthalpy and pressure in the driven tube nozzle reservoir condition can be varied by changing the driven tube geometry and initial gas fill pressure. Reducing the driven tube diameter yields only very modest increases in reservoir pressure and enthalpy. Reducing the driven tube initial gas fill pressure can increase the reservoir enthalpy significantly, but at the cost of reduced reservoir pressure and useful test time. A new technique, the insertion of a converging section in the driven tube is found to produce substantial increases in both reservoir pressure and enthalpy. Using a one-dimensional inviscid full kinetics code, a number of different locations and shapes for the converging driven tube section were studied and the best cases found. For these best cases, for driven tube diameter reductions of factors of 2 and 3, the reservoir pressure can be increased by factors of 2.1 and 3.2, respectively and the enthalpy can be increased by factors of 1.5 and 2.1, respectively.

Bogdanoff, David W.↗
NASA NTRS1985

A stagnation pressure probe for droplet-laden air flow

It is often of interest in a droplet-laden gas flow to obtain the stagnation pressure of both the gas phase and the mixture. A flow-decelerating probe (TPF), with separate, purged ports for the gas phase and the mixture and with a bleed for accumulating liquid at the closed end, has been developed. Measurements obtained utilizing the TPF in a nearly isothermal air-water droplet mixture flow in a smooth circular pipe under various conditions of flow velocity, pressure, liquid concentration and droplet size are presented and compared with data obtained under identical conditions with a conventional, gas phase stagnation pressure probe (CSP). The data obtained with the CSP and TPF probes are analyzed to determine the applicability of the two probes in relation to the multi-phase characteristics of the flow and the geometry of the probe.

Murthy, S. N. B.↗
NASA NTRS1974

Stagnation pressure probe

A method and apparatus for measuring the stagnation pressure of supersonic velocity gas streams without the generation of shock waves which interfere with such measurements are given. The technique is insensitive to the type of gas and Mach number and is therefore particularly useful in the study of jet engine exhausts.

Goodyer, M. J.↗
NASA NTRS1990

Prediction of inviscid stagnation pressure losses in supersonic inlet flows

An effort is made to quantify the stagnation pressure losses associated with shock-wave systems that may be present in such high Mach number flows as those of scramjet hypersonic diffusers. If the shock-related contribution turns out to be much larger than that attributable to viscous effects, a designer could introduce methods for the minimization of the shock system's scale; in particular, the size of the normal shock should be reduced. The angles presently treated may be approached during vehicle maneuvering or other transients.

Azevedo, David J.↗
DOE OSTI2018

Increasing stagnation pressure and thermonuclear performance of inertial confinement fusion capsules by the introduction of a high-Z dopant

Inertial confinement fusion requires the inertia of the imploding mass to provide the necessary confinement such that the core reaches adequate high density, temperature, and pressure. Studies utilize low-Z capsules filled with hydrogenic fuel, which are subject to multiple instabilities at the interfaces during the implosion. To improve the stability of the fuel:capsule interface and narrow the imploding shell profile, capsules are doped with a small atomic percentage of a high-Z material. A series of recent indirect-drive experiments executed at the National Ignition Facility with tungsten-doped high density carbon capsules has demonstrated that the presence of this dopant serves to increase the in-flight aspect ratio of the shell and increase the compression and neutron yield performance of both gas-filled and deuterium-tritium cryogenically layered targets. These experiments definitively show that benefits accrued by the introduction of a high-Z dopant into the capsule can outweigh the detrimentally reduced stability of the ablation front, avoiding shell breakup or significant radiative cooling of the hot spot. Future experiments will utilize these types of capsules to additionally increase nuclear performance.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1993

Increase in stagnation pressure and enthalpy in shock tunnels

A new technique based on the insertion of a converging section in the driven tube is described which is capable of producing substantial increases in both reservoir pressure and enthalpy. A 1D inviscid full kinetics code is used to study a number of different locations and shapes for the converging driven tube section. For driven tube diameter reductions of factors of 2 and 3, the reservoir pressure is found to increase by factors of 2.1 and 3.2, respectively, and the enthalpy is found to simultaneously increase by factors of 1.5 and 2.1, respectively.

Bogdanoff, David W.↗
NASA NTRS2011

Enthalpy Distributions of Arc Jet Flow Based on Measured Laser Induced Fluorescence, Heat Flux and Stagnation Pressure Distributions

The centerline total enthalpy of arc jet flow is determined using laser induced fluorescence of oxygen and nitrogen atoms. Each component of the energy, kinetic, thermal, and chemical can be determined from LIF measurements. Additionally, enthalpy distributions are inferred from heat flux and pressure probe distribution measurements using an engineering formula. Average enthalpies are determined by integration over the radius of the jet flow, assuming constant mass flux and a mass flux distribution estimated from computational fluid dynamics calculations at similar arc jet conditions. The trends show favorable agreement, but there is an uncertainty that relates to the multiple individual measurements and assumptions inherent in LIF measurements.

Suess, Leonard E.↗
NASA NTRS1974

Calculation of supersonic stream parameters of a real gas from measurable quantities using FORTRAN 4 routines

Sets of routines are presented that calculate such real-gas supersonic stream properties as velocity, density, enthalpy, entropy, and isentropic exponent. Two alternative sets of measurements are assumed: (1) stagnation pressure, stagnation temperature, and the pressure on the surface of a static-pressure wedge; or (2) pressure and temperature in a plenum upstream of a supersonic nozzle and the stagnation pressure at the exit of this nozzle. The routines are applicable to any gas whose properties are known. Explicit routines are presented for determining these properties for air, nitrogen, oxygen, normal hydrogen, para-hydrogen, helium, argon, steam, methane, and natural gas.

Johnson, R. C.↗
NASA NTRS2002

Using Temperature Sensitive Paint Technology

New facilities and test techniques afford research aerodynamicists many opportunities to investigate complex aerodynamic phenomena. For example, NASA Langley Research Center's National Transonic Facility (NTF) can hold Mach number, Reynolds number, dynamic pressure, stagnation temperature and stagnation pressure constant during testing. This is important because the wing twist associated with model construction may mask important Reynolds number effects associated with the flight vehicle. Beyond this, the NTF's ability to vary Reynolds number allows for important research into the study of boundary layer transition. The capabilities of facilities such as the NTF coupled with test techniques such as temperature sensitive paint yield data that can be applied not only to vehicle design but also to validation of computational methods. Development of Luminescent Paint Technology for acquiring pressure and temperature measurements began in the mid-1980s. While pressure sensitive luminescent paints (PSP) were being developed to acquire data for aerodynamic performance and loads, temperature sensitive luminescent paints (TSP) have been used for a much broader range of applications. For example, TSP has been used to acquire surface temperature data to determine the heating due to rotating parts in various types of mechanical systems. It has been used to determine the heating pattern(s) on circuit boards. And, it has been used in boundary layer analysis and applied to the validation of full-scale flight performance predictions. That is, data acquired on the same model can be used to develop trends from off design to full scale flight Reynolds number, e.g. to show the progression of boundary layer transition. A discussion of issues related to successfully setting-up TSP tests and using TSP systems for boundary layer studies is included in this paper, as well as results from a variety of TSP tests. TSP images included in this paper are all grey-scale so that similar to pictures from sublimating chemical tests areas of laminar flow appear "lighter," or white, and areas of turbulent flow appear "darker."

Hamner, M. P.↗