Search NASA⌕ Search

SEARCH · Search NASA

Results for “stereolithography”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Dispersion and properties of zirconia suspensions for stereolithography

Abstract Stereolithography is an attractive technique for the fabrication of complex‐shaped ceramic components with high dimensional accuracy. One of the challenges in this technology is the development of high solid loading, low viscosity photosensitive ceramic suspension. In this study, the dispersion of zirconia in photocurable resin and the slurry properties were intensively investigated. Rheological measurements showed that DISPERBYK‐103 proved to be an effective dispersant. 42 vol% ZrO 2 suspension was successfully prepared using 3.5 wt% DISPERBYK‐103 as the dispersant, with a suitable viscosity (4.88 Pa·s) below the maximum allowable viscosity value (5 Pa·s) for stereolithography applications. The adsorption behavior of DISPERBYK‐103 on the surface of zirconia powders was characterized by TG and FT‐IR, confirming the dispersion effect of dispersant. Contact angle measurements were also conducted to show that the adsorption of DISPERBYK‐103 could help to improve the wettability between powder and photocurable resin. Results showed that DISPERBYK‐103 was effective for the preparation of suitable slurries for the development of ZrO 2 ceramics through stereolithography.

Li, Xingbang↗

Mask Projection Stereolithography for Manufacturing Ceramic Parts for CO 2 Capture and Sequestration

With increased CO 2 in the atmosphere and climate change becoming central in today’s political climate, it is important to make attempts to alleviate climate change. CO 2 capture is possible at the source of some of the larges CO 2 producers – industrial firms – where it can be collected via separation membranes. While current state-of-the-art technology is amine gas treatment or polymer membranes, ceramic membranes infilled with hydroxide offer a more energetically efficient solution. Stereolithography offers a unique manufacturing technique to create uniquely-shaped ceramic parts that will maximize carbon capture while maintaining low energy needs and low cost. High-loading ceramic slurries can be more difficult to manufacture using stereolithography due to high viscosity and opacity, but produce stronger pieces when sintered. The current challenge is optimizing high-load ceramic slurries for stereolithography to print pieces with large surface areas and parts on the micrometer-scale.

36 MATERIALS SCIENCE↗

Use of wire grid polarizers with liquid crystal display for large-volume stereolithography

Spatial light modulators that use liquid crystal devices (LCDs) to pattern ultraviolet light for vat polymerization suffer from a few limitations: limited range of wavelengths that can be patterned, low damage threshold for incoming light, and low efficiency of light transmission. A monochrome LCD can more efficiently transmit useful wavelengths of light for stereolithography (365–405 nm) than a color LCD, but it still contains two absorptive film polarizers that suffer from the aforementioned limitations. Wire grid polarizers reflect rather than absorb the blocked polarizations of light, resulting in a higher intensity damage threshold. They can also polarize lower wavelength light that is limited only by the wire pitch. In this work, this research investigates the effects of replacing an LCD’s film polarizers with wire grid polarizers to enable polarization and patterning of high intensity UV light, resulting in shorter curing times and the ability to print a wider range of stereolithography feedstocks.

42 ENGINEERING↗

Shrinkage, microstructure, and mechanical properties of sintered 3D-printed silica via stereolithography

Stereolithography has been used to create ceramic parts with complex geometry that is difficult to achieve with conventional fabrication techniques. Here this study used stereolithography to print silica honeycomb structures with a commercial Formlabs Form2 printer. The printed samples were sintered at different temperatures, and the print shape was retained up to 1300°C, but significant distortion from partial melting occurred at 1400°C. Higher sintering temperatures lead to more shrinkage, but it is non-uniform among directions, with the open cell plane shrinking more than the dense plane of the sample. As expected, the density of samples also increases with the sintering temperature. At higher sintering temperatures, there is an increase in cristobalite and a decrease in quartz, tridymite, and amorphous silica. Regarding mechanical properties, the out-of-plane compressive strength is approximately one order of magnitude higher than the in-plane compressive strength. When compressed along the out-of-plane direction, the samples sintered at lower temperatures surprisingly exhibit higher strength, which is explained by the micro-cracking mechanism. As expected, the samples sintered at higher temperatures display higher strength when compressed along the in-plane direction.

36 MATERIALS SCIENCE↗

Characteristics of products generated by selective sintering and stereolithography rapid prototyping processes

The trend in the modern global economy towards free market policies has motivated companies to use rapid prototyping technologies to not only reduce product development cycle time but also to maintain their competitive edge. A rapid prototyping technology is one which combines computer aided design with computer controlled tracking of focussed high energy source (eg. lasers, heat) on modern ceramic powders, metallic powders, plastics or photosensitive liquid resins in order to produce prototypes or models. At present, except for the process of shape melting, most rapid prototyping processes generate products that are only dimensionally similar to those of the desired end product. There is an urgent need, therefore, to enhance the understanding of the characteristics of these processes in order to realize their potential for production. Currently, the commercial market is dominated by four rapid prototyping processes, namely selective laser sintering, stereolithography, fused deposition modelling and laminated object manufacturing. This phase of the research has focussed on the selective laser sintering and stereolithography rapid prototyping processes. A theoretical model for these processes is under development. Different rapid prototyping sites supplied test specimens (based on ASTM 638-84, Type I) that have been measured and tested to provide a data base on surface finish, dimensional variation and ultimate tensile strength. Further plans call for developing and verifying the theoretical models by carefully designed experiments. This will be a joint effort between NASA and other prototyping centers to generate a larger database, thus encouraging more widespread usage by product designers.

Cariapa, Vikram↗

Development of a variable tensioning system to reduce separation force in large scale stereolithography

Projection micro stereolithography (PµSL) is an additive manufacturing tool that offers multiple advantages, including unparalleled resolution and throughput, but the ability to print high viscosity resin for large-scale parts is limited. One of the key challenges in PµSL is to separate a newly polymerized layer from the vat floor without damaging the part. Since the separation force scales with the printing area, the risk of damaging the part increases significantly with larger-scale systems and must be addressed. In this paper, a novel roll-to-roll, variable tensioning system is proposed to reduce the separation force during printing. A mathematical model is proposed to predict the separation force for different 2D geometries, and a set of experiments is conducted on an experimental prototype to validate the model. Finally, the effects of different separation parameters including peel rate and peel angle are discussed in detail. The results show that the proposed tensioning system reduces the separation force significantly.

36 MATERIALS SCIENCE↗

Wood-reinforced composites by stereolithography with the stress whitening behavior

In this study, poplar wood flour at various concentrations (1–10 wt%) is incorporated into a methacrylate-based resin via solution blending to fabricate wood-reinforced composites using stereolithography apparatus (SLA) 3D printing. Differential scanning calorimetry (DSC) along with Fourier transform infrared spectroscopy (FTIR) analysis shows the presence of a small amount of residual monomer in the printed samples. For the printed composites, the glass transition temperature (T g ) from dynamic mechanical analysis (DMA) decreases as more wood flour is incorporated, which indicates an increase in free volume occupied by polymer chains. The tensile strength is improved up to 17.3% from 21.1 MPa (no wood flour) to 24.7 MPa (1.0 wt% wood flour). The highest Young’s modulus reaches 323.8 MPa (2.0 wt% wood flour), which is 1.9-fold of that of the sample without wood flour. Moreover, the composites show “stress whitening” with the addition of wood flour during the uniaxial drawing. Morphology analysis of the tested samples show that the formation of microcraze and microvoids likely causing the stress whitening. This is the first study that demonstrates wood flour can be utilized in SLA 3D printed wood plastic composites (WPC) which can reinforce the printed products with a modest loading amount.

36 MATERIALS SCIENCE↗

3D-printing methacrylate/chitin nanowhiskers composites via stereolithography: Mechanical and thermal properties

We report on the mechanical and thermal properties of stereolithography (SLA) 3D-printed methacrylate (MA) resin reinforced by chitin nanowhiskers (CNWs). CNWs were synthesized by acid hydrolysis of crab shell chitin and nanocomposites with 0 wt%, 0.5 wt%, 1.0 wt%, and 1.5 wt% CNWs loading were prepared by slurry compounding method. The obtained CNWs (diameter = 23 ± 5 nm, length = 253 ± 100 nm, and aspect ratio = 11 ± 3) are well dispersed within the bulk of MA at 1.0 wt% loading, implying good interfacial adhesion between the nanofiller and the resin matrix possibly due to hydrogen bonding interactions. The addition of up to 1.0 wt% CNWs to neat MA enhances the tensile strength, strain at break, modulus, and maximum thermal degradation temperatures of the nanocomposites. Moreover, the incorporation of CNWs not only improves the mechanical and thermal properties, but also preserves the excellent resolution and accuracy of 3D-printed MA/CNWs nanocomposites.

36 MATERIALS SCIENCE↗

Aging of UV curable PDMS developed for large-scale, high viscosity stereolithography

Polydimethylsiloxane (PDMS) elastomers are silicone rubbers that find widespread application in both academic and industrial settings. This study investigates the use of photosensitive platinum catalysts for UV-activated hydrosilylation of PDMS, which enables the additive manufacturing of PDMS objects through techniques such as stereolithography. Specifically, this study focuses on understanding the aging behavior of Pt-catalyzed, UV-curable PDMS samples, including their mechanical behavior under thermal and UV-accelerated aging conditions. The results show that the Pt-catalyzed, UV-curable PDMS introduced in this research is ‘under-cured’ after being printed and will slowly evolve over time resulting in increased stiffness and decreased elongation, likely due to the formation of additional crosslinks. FTIR spectroscopy indicates that no new chemical bonds or functional groups are generated through the aging process, suggesting that no thermal degradation or polymer chain scissions occur in the polymer matrix. Overall, this PDMS formulation exhibits greater mechanical strength and significantly less reduction in strength with aging, compared with the commonly used, UV-curable thiol-ene PDMS.

36 MATERIALS SCIENCE↗

Mechanically and Thermally Enhanced 3D-Printed Photocurable Polymer Nanocomposites Containing Functionalized Chitin Nanowhiskers by Stereolithography

Additive manufacturing, or simply 3D printing (3DP), where objects are built through layer-wise material deposition, has gained significant academic and industrial attention as a result of the development of advanced and functional materials requiring rapid, customized, and flexible solutions. In the context of green manufacturing, diversifying environmentally and economically sustainable material portfolios is an essential endeavor for the success of 3DP technology that uses widely available, highly valuable, and renewable materials. Here, we used stereolithography (SLA) for processing methacrylate-based photocurable resins containing crab shell-derived chitin nanowhiskers (CNWs), which are surface-functionalized by reactive acrylate groups. Results from full spectral, thermal, structural, and topological analyses corroborate not only the surface functionalization of CNWs but also indicate the presence of these photocurable CNW (pCNW) fillers in the 3D-printed nanocomposites. Owing to the strong interfacial bond induced by the physical and chemical crosslinking between the pCNW and methacrylate (MA) polymer matrix, the internally formulated nanocomposites displayed enhanced thermomechanical properties (e.g., storage modulus and glass transition temperature) compared to those of commercially available pure SLA resins. For instance, the inclusion of 0.5 wt % pCNW improved the tensile strength and stiffness to up to 78 and 71%, respectively, without compromising the toughness and ductility of the printed material. Accordingly, this result also evidences the compatibility between the filler and resin materials. Consequently, the formation of a crosslinked network in the nanocomposite structure results in a higher thermal stability and activation energy (i.e., up to ~79%) for all the hybrid materials than the pristine MA. Finally, the high-resolution SLA print features, dimensional accuracy, and enhanced mechanical performance of our microstructure-forming functionalized chitin-based nanocomposites make them promising materials for a wide range of robust and high-performance industrial applications.

36 MATERIALS SCIENCE↗

MONTE CARLO ANALYSES OF THE YALINA THERMAL FACILITY WITH SERPENT STEREOLITHOGRAPHY GEOMETRY MODEL

This paper analyzes the YALINA Thermal subcritical assembly of Belarus using two different Monte Carlo transport programs, SERPENT and MCNP. The MCNP model is based on combinatorial geometry and universes hierarchy, while the SERPENT model is based on Stereolithography geometry. The latter consists of unstructured triangulated surfaces defined by the normal and vertices. This geometry format is used by 3D printers and it has been created by: the CUBIT software, MATLAB scripts, and C coding. All the Monte Carlo simulations have been performed using the ENDF/B-VII.0 nuclear data library. Both MCNP and SERPENT share the same geometry specifications, which describe the facility details without using any material homogenization. Three different configurations have been studied with different number of fuel rods. The three fuel configurations use 216, 245, or 280 fuel rods, respectively. The numerical simulations show that the agreement between SERPENT and MCNP results is within few tens of pcms.

CUBIT↗

Multi‐Material Gradient Printing Using Meniscus‐enabled Projection Stereolithography (MAPS)

Light‐based additive manufacturing methods are widely used to print high‐resolution 3D structures for applications in tissue engineering, soft robotics, photonics, and microfluidics, among others. Despite this progress, multi‐material printing with these methods remains challenging due to constraints associated with hardware modifications, control systems, cross‐contamination, waste, and resin properties. Here, a new printing platform coined Meniscus‐enabled Projection Stereolithography (MAPS) is reported, a vat‐free method that relies on generating and maintaining a resin meniscus between a crosslinked structure and bottom window to print lateral, vertical, discrete, or gradient multi‐material 3D structures with no waste and user‐defined mixing between layers. MAPS is compatible with a wide range of resins shown and can print complex multi‐material 3D structures without requiring specialized hardware, software, or complex washing protocols. MAPS's ability to print structures with microscale variations in mechanical stiffness, opacity, surface energy, cell densities, and magnetic properties provides a generic method to make advanced materials for a broad range of applications.

bioprinting↗

Ability of x‐ray computed tomography to resolve critical flaw size in laser‐based, paste stereolithography ceramic printing of alumina

Abstract Complex alumina parts were printed using vat photopolymerization (VPP), which is a stereolithography‐based additive manufacturing (AM) technique used to shape ceramic preforms, or green parts. The critical flaw size was determined using classical fracture mechanics techniques. The strength and fracture toughness were measured and compared to flaws detected in x‐ray computed tomography (XCT or CT) distributions as well as the fracture surfaces. The strength was lower compared traditionally made alumina, and that is due to layering effects, slurry defects, and printing defects. The critical flaw size from fracture mechanics was 206 µm. XCT has high enough resolution to detect the critical flaw size and much smaller features, where the average flaw size observed in CT scans was around 80–100 µm. The fracture surfaces indicate that flaws causing failure are larger than that of the critical flaw size (∼300 µm), but fracture surfaces do not show definitive features compared to traditionally made ceramics. Since XCT can observe flaws smaller than the critical flaw size, this method can be used as a screening technique.

36 MATERIALS SCIENCE↗

Resin chemistry and particle size influence on stereolithography with silicon carbide

Stereolithography (SLA) is an established process able to produce high resolution polymer parts with complex geometries. Silicon carbide (SiC) has uses in a variety of applications, but traditionally was difficult to manufacture into complex geometries. There have been advances in producing SiC through SLA using a SiC-derived ceramic such as silicon oxycarbide (SiOC). In this study, a slurry using a commercially available resin as the base material with additional modifiers was investigated to create a SiC slurry ready for pressureless sintering. The effects of photoinitiator, dispersant and a bimodal distribution of SiC particle sizes was studied using a design of experiments (DOE). A slurry with a bimodal distribution of 70 % coarse and 30 % fine SiC powder at 40 % solids loading by volume was prepared and successfully printed. Rheology measurements show the slurry to have viscoelastic shear thinning behavior below the recommended 1000 Pas necessary for printing. Printing parameters for the new material on a commercially available SLA printer were studied parametrically. The laser marking speeds found to print the slurry was 260 mm/s and 130 mm/s. A slurry and printing parameters were determined to produce a green part with a proposed debinding cycle.

Herd, Tien [ORNL]↗

Stereolithography 3D Printing of Lignin-Reinforced Composites with Enhanced Mechanical Properties

Due to the availability, biodegradability, and biological effects, lignin has emerged as an interesting alternative to petroleum-based compounds for developing sustainable chemicals, materials, and composites. In this study, lignin at various concentrations was incorporated into methacrylate resin via solution blending to fabricate lignin-reinforced composites using stereolithography apparatus three-dimensional printing. Softwood kraft lignin in the amounts of 0.2, 0.4, 0.5, 0.8, and 1.0 wt % in the methacrylate resin was used as a printing ink, and the gel contents and relative contents of the residual resin in the printed samples with various lignin concentrations were measured. The effects of the lignin on the ultimate mechanical properties of the non-postcured and postcured printed composites were determined. The tensile testing results revealed that the incorporation of lignin in the composite increased the tensile strength by 46–64% and Young’s modulus by 13–37% for the postcured printed composites compared with that of the control sample (no lignin added). Employing a 0.4 wt % softwood kraft lignin, the tensile strength of the postcured printed composite reached the highest value of 49.0 MPa, which was a 60% increase in comparison to that of the control sample with 30.7 MPa. Scanning electron microscopy images of the fracture samples illustrated that the lignin-incorporated composites exhibited a rougher fracture surface that can presumably dissipate the stress, which could be a contributing factor for the mechanical enhancement.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Optimization of PDMS Photoresin for Three-Dimensional Printng via Projection Micro-Stereolithography

As an industry, additive manufacturing (AM) has provided a way to quickly build structures in a cost-effective manner. Furthermore, the ability to utilize a computer aided design file to build said structures permits rapid customization of parts. Threedimensional (3D) printing, specifically projection micro-stereolithography (PμSL), has these qualities in addition to not being restricted by a structure’s geometry. However, printing using a PμSL system is limited by the chemistry the resin undergoes and by resin viscosity. In this work, silicone structures were printed via a thiol-ene “click” reaction, which is less sensitive to oxygen inhibition compared to commercial resins. The resin chemistry was optimized in order to decrease feature size. Formulation changes along with various light intensity doses and exposure times resulted in a 50% decrease in feature sizes. Silica filler was added to the resin to increase mechanical strength. A postcure procedure did not improve the material’s strength, suggesting a full cure is reached during printing.

36 MATERIALS SCIENCE↗

The Effect of Acceleration on the Separation Force in Constrained-Surface Stereolithography

Constrained-surface-based stereolithography has recently attracted much attention from both academic and industrial communities. Despite numerous experimental, numerical and theoretical efforts, the fundamental need to reduce the separation force between the newly cured part and constrained surface has not yet been completely solved. In this paper, we develop a fluid dynamics approach, proposed in our previous work, to theoretically model the separation force in 3D printing of a cylindrical part for flat and patterned windows. We demonstrate the possibility of separation force reduction with an accelerated movement of the printing platform. In particular, we investigate behaviors of transient parameter, its reduction rate, and separation force reduction with respect to elevation speed and time. The proposed approach involves deceleration and acceleration stages and allows to achieve the force reduction for the entire printing process. Finally, we provide implicit analytical solutions for time moments when switching between the stages can be done without noticeable increase of separation force and explicit expression for separation force in case of patterned window.

Gritsenko, Dmitry (ORCID:0000000248181512)↗