Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface mineralogy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Experimental flow-through a single fracture with monolayer proppant at reservoir conditions: A case study on Caney Shale, Southwest Oklahoma, USA

Global energy systems are undergoing a crucial transition to clean energy sources, thereby moving away from fossil-fuel based energy with the ultimate aim of reducing carbon dioxide emissions. It is essential to continue to advance in exploring and developing shale gas resources as this will underpin the global supply of natural gas that is needed to support the energy transition. The challenge hereby is that the slow fluid flow of the shale matrix due to its very low permeability requires large-scale volume fracturing to produce a conductive fracture network that enhances the connectivity between the shale formation and the wellbore. This work examines the influence of a thin proppant layer on a single fracture using a flow-through experiment, and also explores whether proppant embedment in the Caney shale is affected by the rock mineralogy, surface roughness, fluids, confining stress, time, temperature and bedding. The experiment was conducted for a duration of nine days (216 h), experimental temperature was varied from ambient temperature to reservoir temperature of 125 °C (257 °F) and confining stress was varied from 367 psi (2.53MPa) to a maximum of 4011.82 psi (27.66 MPa). Here, we find that the conductivity of the fracture is primarily influenced by the layer of proppant used, surface roughness, mineralogy, fluids, temperature and closure stress.

Caney shale↗
DOE OSTI2020

Microbially mediated iron redox cycling of subsurface sediments from Hanford Site, Washington State, USA

Iron-bearing clay minerals are predominant in soils and sediments, and they undergo oxidation-reduction cycles as a result of natural processes such as wetting/drying cycles and plant root respiration. However, the kinetics and mechanisms of multiple redox cycles of iron in clay-rich sediments and consequences of such cycling on sediment properties are poorly understood. The objective of this study was to understand how multiple redox cycles of Fe in clay-rich sediment affect the rate and extent of Fe bioreduction and the physicochemical properties of the sediment. A natural sediment sample containing Fe-bearing montmorillonite from Hanford, Washington, USA was size-fractionated [2.0 to 0.5 μm (Hanford-C) and 0.5 to 0.02 μm (Hanford-F)] and redox-cycled for four times. Bioreduction was achieved utilizing Geobacter sulfurreducens and re-oxidization was performed with sparged air. Time-course change of total Fe (II) was monitored to measure the rate and extent of Fe (III) bioreduction. Redox-cycled sediments were characterized to determine the physicochemical changes. Both the initial rate and extent of bioreduction fluctuated across the four redox cycles, but they ultimately decreased from 5.3 μmol g -1 h -1 and 22.9% to nearly zero by the fourth cycle. These fluctuation patterns were likely due to a combined effect of reductive dissolution of small/poorly crystalline clay particles (by 3–5%) and clay mineral structural changes, as evidenced by redox induced changes of aqueous chemistry, surface area, cation exchange capacity, mineralogy, and Mössbauer parameters. Once these small/poorly crystalline clay particles were dissolved, structural Fe in residual larger and more crystalline clay particles was largely reversible across additional redox cycles, as revealed by Mössbauer spectroscopy through the first three cycles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Distinct Fracture Mineralogy That is Out of Equilibrium With Modern Groundwaters Provides Important Context for Subsurface Life

Rock fracture surfaces in the crust are essential habitat for microorganisms. Fracture‐groundwater interfaces provide physical substrates for biofilm growth and are sources of carbon, nutrients, and electron donors and acceptors. To better understand geochemical processes impacting fracture surfaces and the subsurface microbiome, we identified fractures in archived rock cores from the Soudan formation, which is known to host saline groundwaters and isolated microbial communities dependent on rock‐water interactions. Cores with open fractures were thin sectioned and studied via electron microprobe and synchrotron X‐ray fluorescence microprobe. Most fracture surfaces had mineralogy distinct from that of the bulk rock. Chlorite minerals were abundant on fracture surfaces and had elemental compositions suggesting deposition during late‐stage hydrothermal alteration. Fracture‐lining chlorites likely limit access to iron oxide and sulfide minerals that are active in subsurface biogeochemical cycles. Calcium‐rich rinds were also observed along fracture edges. These rinds were too thin and poorly ordered to be identified via light microscopy or X‐ray diffraction; however, Ca K‐edge micro‐X‐ray absorption near‐edge structure spectroscopy identified them as carbonates, minerals not observed in the bulk rock. Thermodynamic modeling shows that carbonate precipitation is largely unfavorable in Soudan groundwaters, indicating that fracture edge conditions differed from those in modern water samples. Because of the low carbon concentrations in Soudan groundwaters, carbonate rinds likely play an important role in subsurface carbon cycling and may mark fracture surfaces that once hosted biofilms. Overall, this study suggests that fracture alteration can both play an active role in and suppress rock‐water interactions essential to subsurface life.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Acid Erosion of Carbonate Fractures and Accessibility of Arsenic-Bearing Minerals: In Operando Synchrotron-Based Microfluidic Experiment

Underground flows of acidic fluids through fractured rock can create new porosity and increase accessibility to hazardous trace elements such as arsenic. In this study, we developed a custom microfluidic cell for an in operando synchrotron experiment using X-ray attenuation. The experiment mimics reactive fracture flow by passing an acidic fluid over a surface of mineralogically heterogeneous rock from the Eagle Ford shale. Over 48 h, calcite was preferentially dissolved, forming an altered layer 200–500 μm thick with a porosity of 63–68% and surface area >10$\times$ higher than that in the unreacted shale as shown by xCT analyses. Calcite dissolution rate quantified from the attenuation data was 3 $\times$ 10 –4 mol/m 2 s and decreased to 3 $\times$ 10 –5 mol/m 2 s after 24 h because of increasing diffusion limitations. Erosion of the fracture surface increased access to iron-rich minerals, thereby increasing access to toxic metals such as arsenic. Quantification using XRF and XANES microspectroscopy indicated up to 0.5 wt % of As(-I) in arsenopyrite and 1.2 wt % of As(V) associated with ferrihydrite. This study provides valuable contributions for understanding and predicting fracture alteration and changes to the mobilization potential of hazardous metals and metalloids.

58 GEOSCIENCES↗
DOE OSTI2022

Elucidating Arsenic and Selenium Speciation in Coal Fly Ashes

Coal fly ash (CFA) is produced during the coal combustion process and contains trace elements (<100 ppm) including selenium (Se) and arsenic (As), both detrimental for environmental and human health. Existing management strategies for CFAs involve disposal in landfills and ash ponds, as well as beneficial usage in other applications such as in concrete. Both the direct disposal and beneficial usage of CFA raise concerns for environmental hazards due to the potential leaching of Se and As. CFAs were classified as reusable material by the U.S. Environmental Protection Agency (EPA) with the first federal regulation (Disposal of Coal Combustion Residuals from Electric Utilities, CCR) for its disposal established six years ago. During coal combustion process, parameters such as furnace firing type, emissions controls, coal rank, use of additives, and particulate matter controls, could contribute to significant variability in As/Se concentrations and their speciation. Although there have been a handful of studies on As/Se speciation on small sets of samples, they do not fully represent the current state of coal-fired electrical generating units. Little information exists on the detailed speciation (e.g. oxidation state, complexation state) of As/Se in large set of fly ash samples. To better investigate the role of the potential contributing parameters, a large-scale survey study with representative samples of typical coal source and combustion conditions is highly desired. The overall goal of this research is to systematically characterize As and Se speciation of representative coal fly ash samples using state-of-the-art synchrotron based spectroscopic and microscopic techniques, in order to develop a correlation between coal source/type, operation condition, As/Se speciation, and As/Se mobility. A detailed survey study was conducted documenting the current state-of-knowledge on fossil power generating units as a function of coal type/source, operating conditions, environmental control systems, additive use, and fly ash handling methods. Based on this survey, a matrix of fly ash samples representing a range of conditions were chosen and collected. The collected ash samples were analyzed for bulk characteristics such as elemental composition, microstructure, chemical and mineralogical composition, surface area, and particle size distribution. State-of-the-art synchrotron X-ray microscopy and spectroscopy techniques were applied to reveal the molecular scale speciation information of As and Se, such as oxidation state, association with other elements/minerals, and complexation states.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2023

A Spectroscopic Study of Mars-analog Materials with Amorphous Sulfate and Chloride Phases: Implications for Detecting Amorphous Materials on the Martian Surface

The Chemistry and Mineralogy X-ray diffraction (XRD) instrument aboard the Curiosity rover consistently identifies amorphous material at Gale Crater, which is compositionally variable, but often includes elevated sulfur and iron, suggesting that amorphous ferric sulfate (AFS) may be present. Understanding how desiccating ferric sulfate brines affect the spectra of Martian material analogs is necessary for interpreting complex/realistic reaction assemblages. Visible and near-infrared reflectance (VNIR), mid-infrared attenuated total reflectance (MIR, FTIR-ATR), and Raman spectra, along with XRD data are presented for basaltic glass, hematite, gypsum, nontronite, and magnesite, each at three grain sizes (<25, 25–63, and 63–180 μm), mixed with ferric sulfate (+/–NaCl), deliquesced, then rapidly desiccated in 11% relative humidity or via vacuum. All desiccated products are partially or completely XRD amorphous; crystalline phases include starting materials and trace precipitates, leaving the bulk of the ferric sulfate in the amorphous fraction. Due to considerable spectral masking, AFS detectability is highly dependent on spectroscopic technique and minerals present. This has strong implications for remote and in situ observations of Martian samples that include an amorphous component. AFS is only identifiable in VNIR spectra for magnesite, nontronite, and gypsum samples; hematite and basaltic glass samples appear similar to pure materials. Sulfate features dominate Raman spectra for nontronite and basaltic glass samples; the analog material dominates Raman spectra of hematite and gypsum samples. MIR data are least affected by masking, but basaltic glass is almost undetectable in MIR spectra of those mixtures. NaCl produces similar FTIR-ATR and Raman features, regardless of analog material.

58 GEOSCIENCES↗
DOE OSTI2022

Partitioning behavior and mechanisms of rare earth elements during precipitation in acid mine drainage

Rare earth elements (REEs) are frequently found concentrated in acid mine drainage (AMD). The recovery of REEs from AMD has been successfully achieved using selective chemical precipitation. However, a portion of the REEs is often lost to the precipitates of the dominant metal contaminant ions. To better understand the REE partitioning behavior and mechanisms during the precipitation process, a systematic study was performed on both natural and synthetic AMD solutions. Precipitation test results show that REE removal was noticeably elevated at pH 4.0 after adding H 2 O 2 to convert ferrous to ferric ions, causing nearly complete precipitation of iron. Solution equilibrium calculations suggested that the REE removal increase was realized through adsorption onto the surfaces of the ferric precipitates. The presence of aluminum species in the solutions reduced the adsorption of REEs on the ferric precipitates. Based on electro-kinetic test results, it was concluded that aluminum species neutralize the negative surface charge of the ferric precipitates and compete with REEs for the adsorption active sites. The presence of ferrous ions in the solutions reduced REE adsorption on the aluminum precipitates at lower pH values (e.g., 5.0) due to competitive adsorption. However, at higher pH values (e.g., 6.0), REE removal to the precipitate product increased due to the precipitation of ferrous ions. Additionally, to the electro-kinetic tests and solution equilibrium calculations, mineralogy characterization, specific surface area measurement, particle size analysis, and morphology analysis were also conducted to investigate and identify the partitioning mechanisms.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Link Between CO 2 –Induced Wettability and Pore Architecture Alteration

Changes in pore (throat) size, surface roughness and mineralogy induced by supercritical-CO 2 -water-rock reactions impact petrophysical properties such as porosity, permeability, and especially wettability. Herein, we show that these changes directly impact relative permeability and capillary pressure curves, a fact rarely studied in the literature. In this work, we show that CO 2 contact angle changes emerge after Madison Limestone samples were soaked for 400 hours in CO 2 -enriched brine. Coreflooding results show that the water production rate and cumulative water production increased after the rock was exposed to carbonic acid. Moreover, the mercury capillary pressure decreased in meso- and macro-pores, indicating the increase of size in these pores due to reactions. This compounded wettability and pore network alteration can directly affect CO 2 injectivity, migration and storage capacity. Furthermore, this fundamental insight into CO 2 geological storage processes should aid practitioners to reduce uncertainties in forecasting CO 2 distribution via injection simulation.

58 GEOSCIENCES↗
DOE OSTI2023

Effects of Fe(III) (hydr)oxide mineralogy on the development of microbial communities originating from soil, surface water, groundwater, and aerosols

Microbial Fe(III) reduction is a key component of the iron cycle in natural environments. However, the susceptibility of Fe(III) (hydr)oxides to microbial reduction varies depending on the mineral's crystallinity, and the type of Fe(III) (hydr)oxide in turn will affect the composition of the microbial community. Here, we created microcosm reactors with microbial communities from four different sources (soil, surface water, groundwater, and aerosols), three Fe(III) (hydr)oxides (lepidocrocite, goethite, and hematite) as electron acceptors, and acetate as an electron donor to investigate the shaping effect of Fe(III) mineral type on the development of microbial communities. During a 10-month incubation, changes in microbial community composition, Fe(III) reduction, and acetate utilization were monitored. Overall, there was greater reduction of lepidocrocite than of goethite and hematite, and the development of microbial communities originating from the same source diverged when supplied with different Fe(III) (hydr)oxides. Furthermore, each Fe(III) mineral was associated with unique taxa that emerged from different sources. This study illustrates the taxonomic diversity of Fe(III)-reducing microbes from a broad range of natural environments.

58 GEOSCIENCES↗
DOE OSTI2022

Can fractal dimensions objectivize gastropod shell morphometrics? A case study from Lake Lugu (SW China)

1. Morphometrics are fundamental for the analysis of size and shape in fossils, particularly because soft parts or DNA are rarely preserved and hard parts such as shells are commonly the only source of information. Geometric morphometrics, that is, landmark analysis, is well established for the description of shape but it exhibits a couple of shortcomings resulting from subjective choices during landmarking (number and position of landmarks) and from difficulties in resolving shape at the level of micro-sculpture. 2. With the aid of high-resolution 3D scanning technology and analyses of fractal dimensions, we test whether such shortcomings of linear and landmark morphometrics can be overcome. As a model group, we selected a clade of modern viviparid gastropods from Lake Lugu, with shells that show a high degree of sculptural variation. Linear and landmark analyses were applied to the same shells in order to establish the fractal dimensions. 3. The genetic diversity of the gastropod clade was assessed. The genetic results suggest that the gastropod clade represents a single species. The results of all morphometric methods applied are in line with the genetic results, which is that no specific morphotype could be delimited. Apart from this overall agreement, landmark and fractal dimension analyses do not correspond to each other but represent data sets with different information. Generally, the fractal dimension values quantify the roughness of the shell surface, the resolution of the 3D scans determining the level. In our approach, we captured the micro-sculpture but not the first-order sculptural elements, which explains that fractal dimension and landmark data are not in phase. 4. We can show that analyzing fractal dimensions of gastropod shells opens a window to more detailed information that can be considered in evolutionary and ecological contexts. We propose that using low-resolution 3D scans may successfully substitute landmark analyses because it overcomes the subjective landmarking. Analyses of 3D scans with higher resolution than used in this study will provide surface roughness information at the mineralogical level. We suggest that fractal dimension analyses of a combination of differently resolved 3D models will significantly improve the quality of shell morphometrics.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Feasibility of Algal Biochar, a Byproduct of Biofuel Production, as a Supplemental Cementitious Material

Algal biochar, as the solid residue of biofuel production from algal biomass, is reported to explore disposition options, aiming to lessen the liability or obstacles to biofuel production processes. However, landfills and open combustion lead to adverse environmental impacts. One way to add value to such wastes is to use them as admixtures in cementitious construction materials. This study aims to investigate the feasibility of algae-derived biochar as supplementary cementitious materials (SCM) at different water contents and mixture ratios. Algal biochar-cement composites were prepared with different algal biochar content as well as different water-to-cement (w/c) ratios, and the surface area, morphology, elemental, and mineralogical composition were characterized. To compensate for the high-water absorption of algal biochar, a small concentration of a superplasticizer was used since higher w/c ratios negatively impact strength. The mechanical performance of algal biochar-cement composites is compared with control composites using commercial silica fume as a typical commercial SCM. The findings suggest that algal biochar is a promising candidate to replace commercial SCM, like silica fume, since algal biochar-cement composites can reach comparable compressive strength and Young’s modulus to commercial pozzolan-cement materials with the same w/c ratio, though at later curing times, 33 days. Although the tensile strength of algal biochar-cement composites is statistically similar at 7 days, it is significantly lower at later curing times, and further investigation is required to improve this property. Algal biochar-based cement binders showed comparable embodied carbon to silica fume-based cement binders based on a cradle-to-gate lifecycle analysis. However, the ability of algal biochar to absorb large volumes of CO 2 over short periods of time, as measured in this study, makes this novel SCM an excellent alternative to reduce the embodied carbon of concrete structures cradle-to-grave at 1/10 of the cost. In conclusion, valorization of algae-derived solid waste provides great potential to reduce embodied carbon and brings credit to biofuel production and concrete-based construction.

algae-derived↗
DOE OSTI2021

Spectral Induced Polarization-Biogeochemical Relationships for Remediation Amendment Monitoring

Geophysical tools such as electrical resistivity (ER) can indirectly monitor subsurface changes in response to remedial injections. These methods exhibit relatively low spatial resolution compared to sediment core characterization but are advantageous due to the ability to collect measurements non-intrusively over time across large volumes of the subsurface. Moreover, along with confirmatory groundwater or core sampling, geophysical methods can be used during active biogeochemical remedies to monitor short-term contaminant transformations and mobility, as well as part of an overall strategy for long-term monitoring of subsurface contaminated sites. The use of alternating current spectral induced polarization (SIP) provides significantly more information than conventional geophysical methods like direct current ER. SIP allows for monitoring changes in both solution and surface conductivity by separation of real and imaginary conductivity, respectively, as well as surface capacitance. In principle, SIP can measure indicators of remedy progression such as precipitation reactions that sequester contaminants, potentially providing a better indication of amendment delivery and reactivity as compared to conventional ER methods. However, multiple processes and material properties have overlapping (interacting) electrical responses across a range of frequencies. Hence, the purpose of this scoping study was to evaluate if SIP can be used to monitor (a) amendment delivery and (b) precipitation and reactivity of amendments under consideration at Hanford. SIP measurements were collected in fully saturated columns packed with sand and Hanford formation sediments containing (a) amendments that were highly conductive with significant capacitance (zero valent iron – ZVI, sulfur modified iron – SMI) and (b) amendments that exhibited low electrical conductivity with a small capacitance (calcite, apatite, bismuth). The sand was a quartz material with homogenous particle size that exhibited a relatively low surface conductivity. It was used as a control for comparison with the sediments from the Hanford Site, which have a greater surface conductivity because of their complex mineralogy and heterogeneous particle size distribution and may have complex interactions with amendments. The amendment mass fraction was varied to represent the different stages and subsurface locations associated with the delivery of a remedy. The primary objective was to identify the solution and solid surface changes associated with the delivery amendments and their secondary reactions within the subsurface. The figure below summarizes results for the amendments tested through this project. The SIP phase shift or imaginary conductivity change for the high conductivity amendments was more than 10 times that of the low conductivity amendments, highlighting the relative ease of detection of ZVI and SMI independent of the background signal from sand or Hanford sediments. The ZVI phase shift and imaginary conductivity changes occur primarily at high frequency (> 100 Hz) whereas SMI changes were at low frequency (0.01 to 10 Hz). SIP signals of SMI also increased over time and the maximum shifted to lower frequencies. The low conductivity amendments (calcite, abiotic and biotic apatite, bismuth subnitrate) exhibited relatively small phase and imaginary conductivity changes when added to sediments. The changes were above minimum detection limits (0.5 mrad for phase shift, 0.03 µS/cm for imaginary conductivity) for the highest concentration except for the commercial bismuth material. The lowest amendment concentration that can be detected is likely sediment specific, as minerals in sediments (clays, magnetite, Fe-oxides) have some capacitance and, therefore, exhibit a variable phase shift.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Characterizing mineralization on low carbon steel exposed to aerated and degassed synthetic hydraulic fracture fluids

This study investigates the mineralization occurring at the interface between injected hydraulic fracturing fluids and steel production casing during the shut-in period of unconventional shale wells. Mild steel coupons were reacted with synthetic hydraulic fracturing fluids with varying base fluid and dissolved gas concentrations. Experiments were carried out in an autoclave system set at 50 °C and 2000 PSI for 2 and 14 days. Physical and mineralogical changes to the steel coupons’ surface were characterized using an FEI Quanta 600 field emission gun (FEG) scanning electron microscope (SEM) and a PANalytical XPert Pro diffractometer. Barite precipitation occurred ubiquitously during the first 48 hours in all experimental scenarios. Sulfate radicals created from degradation and reduction of ammonium persulfate breakers facilitate barite formation. Concomitant barite and corrosion related precipitates on the sample surfaces suggest iron hydroxy salts act as nucleation sites for mineral scale growth. These results suggest hydraulic fracturing fluids may have deleterious effects on the wellbore before production of the well begins.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Fast redox switches lead to rapid transformation of goethite in humid tropical soils: A Mössbauer spectroscopy study

Abstract Humid tropical forest soils experience frequent rainfall, which limits oxygen diffusion and creates redox heterogeneity in upland soils. In this study we gauged the effect of short‐term anoxic conditions on Fe mineralogy of relatively Fe‐ and C‐rich surface soils (C/Fe mole ratio ∼5) from a humid tropical forest in Puerto Rico. Soils subjected to 4‐d oxic/anoxic oscillation were characterized by selective chemical extractions, Mössbauer spectroscopy (MBS), and X‐ray diffraction. Chemical extraction data suggested that rapidly switching redox conditions had subtle effects on bulk Fe mineralogy. Mössbauer, on the other hand, indicated that (a) the soil Fe is a mixture of goethites of varying characteristics with minor contributions from ferrihydrite (<5%) and Fe(III)‐organic matter (OM) phases (∼10%), and (b) anoxic conditions rapidly transformed all forms of goethite to relatively stable Fe oxides. Such fast changes in goethite features could be due to rapid depletion and sorption of bio‐released structural Al or sorbed OM onto residual soil components. The rapid temporal changes in MBS parameters and corresponding pore water nominal oxidation state of C values suggest that Fe‐C transformations in these upland tropical soils are complex and intricately coupled. A comprehensive understanding of the fate of Fe, Al, and OM (Fe‐organic moieties) during redox switches and concurrent changes in pore water chemistry is critical for development of robust transport models in humid tropical soils, which are subject to episodic low‐redox events.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Reactive Transport Modeling of Hydrogen Production from Serpentinization of Olivine

Hydrogen production from serpentinization of ultramafic rocks represents a promising natural pathway for generating carbon-free energy, yet its kinetics and controlling factors remain incompletely understood. A key challenge in advancing serpentinization research lies in the heterogeneity of porosity and permeability in rocks, which leads to nonuniform fluid velocity fields, as well as uncertainties in estimating reactive surface area and identifying appropriate mineral reaction equilibria. Additional complexities arise from the role of dissolved SiO 2 , Fe 2+ /Fe 3+ partitioning, and the limited effect of pH variations within the strongly alkaline regime on hydrogen yields. These challenges hinder straightforward extrapolation from laboratory tests to practical applications of hydrogen production from natural rocks. Here, in this work, we address these questions using a simulation-based reactive transport modeling framework calibrated against controlled laboratory experiments reported elsewhere. The model couples geochemical kinetics, multiphase flow, and mineralogical feedbacks, enabling systematic evaluation of how surface area, dissolved silica concentration, Fe redox state, temperature, and pressure govern serpentinization and H2 generation. We find that surface area exerts the strongest control on reaction rates and hydrogen yields, while Fe 2+ /Fe 3+ ratios act as secondary modulators. Elevated dissolved silica concentrations suppress hydrogen production but accelerate serpentine precipitation, whereas increasing pH beyond 12 within the strongly alkaline regime produces only marginal gains. Finally, we demonstrate that integrating targeted experiments with calibrated simulations offers a powerful and efficient approach for predicting hydrogen yields and assessing parameter trade-offs in industrial-scale applications. This integration can substantially reduce the experimental burden while improving predictive capability, thereby enhancing both the mechanistic understanding and the practical feasibility of hydrogen production from serpentinization.

08 HYDROGEN↗
DOE OSTI2025

Dust Direct Radiative Effect Including Large Particles and Component Minerals

The direct radiative effect (DRE) of dust aerosols in Earth system models (ESMs) remains highly uncertain, largely due to inadequate representations of particle size distribution (PSD) and mineral composition. Using NASA's Earth Surface Mineral Dust Source Investigation (EMIT) soil mineralogy data and observed PSD in an ESM that resolves dust mineral composition and emitted diameters from 0.1 to 70 μm, we find a near-neutral global dust net DRE (−0.057 W m −2 ), weaker than most previous estimates. Large dust (diameter >10 μm) contributes 30% of the global longwave dust optical depth, providing observational constraints on large-particle abundance, and offsets 20% of the dust shortwave cooling over major source regions. Incorporation of EMIT mineralogy reduces shortwave uncertainty by more than 50%. The remaining uncertainty mainly exists in processes controlling dust abundance, particularly the poorly understood transport of large dust, and longwave optical properties, which require additional observational constraints to more accurately quantify the dust DRE.

Li, Longlei [Cornell Univ., Ithaca, NY (United Sta↗
DOE OSTI2022

Impact of Concurrent Solubilization and Fines Migration on Fracture Aperture Growth in Shales during Acidized Brine Injection

Acidic hydraulic fracturing fluid chemically and physically alters shale rock fabric during injection and shut-in, creating a “reaction-altered zone” along the fracture faces. To better characterize the variable thickness and composition of this reaction-altered zone under advective flow, we take a coupled experimental and modeling approach. A fluidic cell, with six fiducial markers, is first fabricated to keep the rock sample in place during the core floods and to allow image alignment of acquired images. Then, we conduct a series of reactive core floods in a clay-rich siliceous Wolfcamp shale sample with 10 wt % carbonate, using a synthetic fracturing fluid under no confining stress and at room temperature. High-resolution computed tomography (CT) scans are periodically conducted to observe the spatial alteration of the fracture network. We then perform scanning electron microscopy (SEM-EDS) on the two orthogonal surfaces (fracture surface and freshly cut profile face) to generate high-resolution elemental maps that show the change in mineralogy, both with distance along a given flow path along a fracture surface and with depth from the fracture surface into the shale matrix. These results are contrasted against a two-dimensional (2D) advection-diffusion reaction model developed previously for batch reactions between shale and synthetic fracturing fluids. The model simulates the geochemical interaction occurring at the fracture/matrix interface and penetrating into the shale matrix during the reactive core flood. Both model and experimental results show that the acidic brine is neutralized during the core flood, corresponding to an increase in fracture aperture as a function of fluid volume injected with the greatest change near the inlet. SEM-EDS scans reveal significant dissolution of carbonates on the fracture surface without pyrite oxidation. The reactive transport model indicates that carbonate depletion into the shale interior should be observable, yet SEM-EDS shows no discernible loss of carbonate in the orthogonal profile face. The combination of these observations suggests an additional fracture evolution mechanism in the reactive system, i.e., fines migration. We show that fines migration enhances the access of fracturing fluid to the matrix resulting in a more pronounced fracture widening. Finally, we conclude that coupled mineral dissolution and fines migration govern fracture aperture growth during acidized brine injection. In this work, we effectively show the underlying risk of relying solely on models that do not include an important (transport) process that can alter the system significantly and propose a combined chemomechanical mechanism for fracture evolution appropriate for this shale mineralogy.

58 GEOSCIENCES↗
DOE OSTI2020

Engineered Barrier System R&D and International Collaborations – LANL (FY20): Spent Fuel and Waste Disposition

The United States Department of Energy’s Spent Fuel and Waste Disposition (SFWD) program is investigating the design and safety function of generic nuclear geologic repositories in a variety of geologic settings (salt, argillite, and crystalline rock). Different configurations and loadings of spent nuclear fuel and waste within disposal canisters are also being investigated, some of which have the potential to generate repository temperatures higher than previously considered (i.e., temperatures >100ºC) by foreign and domestic concepts. This report expands on engineered barrier material stability in a high temperature crystalline rock repository through high temperature hydrothermal experiments. Experiments were designed to develop engineered barrier system (EBS) concepts in a hightemperature crystalline environment in 1) bentonite-Grimsel Granodiorite interactions, 2) bentonite-cement reactions, and 3) interaction between waste canister materials and bentonite. Experiment results are applied to understanding long-term repository performance in terms of radionuclide isolation. One hydrothermal experiment was completed in the rocking autoclaves at LANL in FY-20: IEBS-6 (Grimsel Granodiorite + Wyoming bentonite + cured ordinary Portland cement + Grimsel Granodiorite synthetic groundwater, 250ºC/150 bar, 8 weeks). Several other experiments were planned but were delayed due to the COVID-19 pause in laboratory work. In addition, some characterization of the reaction products of experiments conducted in FY-20 was prevented by COVID-19. Mineral phase chemistry was not measured via electron microprobe analyses for IEBS-6. Quantitative X-ray diffraction results from IEBS-6 and HBT-1 were not completed. The missing analyses and discussion of the results will be included in next year’s report. New characterization that was completed includes scanning electron microscopy of reaction products from IEBS-6, quantitative X-ray diffraction results are presented from IEBS-1 through IBES-5, preliminary scanning electron microscope images and chemical analyses for IEBS-6, X-ray diffraction of the clay fraction from all experiments, measurement/imaging of mineral growth on the surface of steel coupons. Major observations pertaining to bentonite stability in a Grimsel Granodiorite environment include the stability of Na-montmorillonite at 250°C, the formation of trace CSH phases, and the formation of bentonite colloids on experiment cooling. The addition of a cured chip of Portland cement to the bentonite-Grimsel system results in slightly higher pH values and the formation of diverse secondary mineral phases that were not observed in the previous experiments (e.g., analcime, garronite, CSH phases). The new characterization efforts related to the interaction of stainless-steel coupons and bentonite clay focused on thickness and mineralogy of phases that formed at the steel surface. In Wyoming bentonite + Grimsel Granodiorite systems, newly formed minerals at the bentonitesteel coupon interface included alteration of the outermost steel edge to Fe,Cr-oxide phases, followed by Fe-rich phyllosilicates (Fe-saponite, chlorite) and interbedded Fe,Cr,Ni-sulfide phases (pentlandite). Hydrothermal experiments were completed to assess uranium-carbonate complexation at conditions relevant to high-temperature disposal. Autoclave solubility experiments were conducted at 150 to 250ºC with a range of carbonate and uranium concentrations. The experiment results were characterized via situ UV-Visible spectroscopy and synchrotron-based in situ XAS techniques. Results show a significant decrease in the stability of uranyl-carbonate complexes at temperatures above 100ºC along with the precipitation of uranium oxides. Further, at T > 200ºC, results show that uranyl-hydroxyl complexes control solubility of uranium instead of the previously predicted uranyl-carbonate species. These results are significant for understanding the mobility of uranium in the EBS, which will likely contain carbonate-rich fluids. International research efforts focused on three main areas: 1) participation in international conferences, 2) building collaborations with foreign repository programs, and 3) the initiation of an experimental program to complement the full-scale HotBENT test at the Grimsel test site. This experiment included Wyoming bentonite + low carbon steel + Grimsel Granodiorite synthetic groundwater and was run at the planned maximum temperature of the HotBENT test (200°C). Complete characterization of reaction products was hindered by disruptions to laboratory work but will be reported in the next FY. The experimental results obtained in FY-20 continue to document the wide-ranging effects of bulk composition and pressure-temperature conditions in the mineralogical and geochemical evolution of a high-temperature repository environment. Concepts developed will be used to inform models of long-term material stability in a generic crystalline rock-hosted repository.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗