SEARCH · Search NASA

Results for “teeth”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

All sources NASA NTRS DOE OSTI

NASA NTRS1986

Experimental rotordynamic coefficient results for teeth-on-rotor and teeth-on-stator labyrinth gas seals

An experimental test facility is used to measure the rotordynamic coefficients of teeth-on-rotor and teeth-on-stator labyrinth gas seals. Direct damping coefficients are presented for these seals for the first time. The results are presented for the two seal configurations at identical operating conditions, and show that, in a rotordynamic sense, the teeth-on-stator seal is more stable than the teeth-on-rotor seal, for inlet tangential velocity in the direction of rotation.

Childs, D. W.↗

NASA NTRS1987

Experimental rotordynamic coefficient results for teeth-on-rotor and teeth-on-stator labyrinth gas seals

Childs, Dara W.↗

NASA NTRS1982

The optimal design of involute gear teeth with unequal addenda

The design of a gear mesh is treated with the objective of minimizing the gear size for a given gear ratio, pinion torque, pressure angle, and allowable tooth lengths. Tooth strengths considered include scoring, pitting fatigue, and bending fatigue. Kinematic involute interference is avoided. The design variation on standard spur gear teeth called the long and short addendum system, is considered. In this system the mesh center distance and pressure angle are maintained as is the ability to manufacture the teeth with standard tooling. However, the pinion and gear tooth proportions are altered in order to obtain fewer teeth numbers for the same ratio as standard gears without kinematic involute interference. The effect of this nonstandard gearing geometry with on tooth strengths and gear mesh size are studied. For a 2:1 gearing ratio, the optimal nonstandard gear design is compared with the optimal standard gear design.

Savage, M.↗

NASA NTRS1992

Contact stresses in meshing spur gear teeth: Use of an incremental finite element procedure

Contact stresses in meshing spur gear teeth are examined. The analysis is based upon an incremental finite element procedure that simultaneously determines the stresses in the contact region between the meshing teeth. The teeth themselves are modeled by two dimensional plain strain elements. Friction effects are included, with the friction forces assumed to obey Coulomb's law. The analysis assumes that the displacements are small and that the tooth materials are linearly elastic. The analysis procedure is validated by comparing its results with those for the classical two contacting semicylinders obtained from the Hertz method. Agreement is excellent.

Hsieh, Chih-Ming↗

NASA NTRS1995

Bending strength model for internal spur gear teeth

Internal spur gear teeth are normally stronger than pinion teeth of the same pitch and face width since external teeth are smaller at the base. However, ring gears which are narrower have an unequal addendum or are made of a material with a lower strength than that of the meshing pinion may be loaded more critically in bending. In this study, a model for the bending strength of an internal gear tooth as a function of the applied load pressure angle is presented which is based on the inscribed Lewis constant strength parabolic beam. The bending model includes a stress concentration factor and an axial compression term which are extensions of the model for an external gear tooth. The geometry of the Lewis factor determination is presented, the iteration to determine the factor is described, and the bending strength J factor is compared to that of an external gear tooth. This strength model will assist optimal design efforts for unequal addendum gears and gears of mixed materials.

Savage, Michael↗

NASA NTRS2017

Brushing Your Spacecrafts Teeth: A Review of Biological Reduction Processes for Planetary Protection Missions

Much like keeping your teeth clean, where you brush away biofilms that your dentist calls "plaque," there are various methods to clean spaceflight hardware of biological contamination, known as biological reduction processes. Different approaches clean your hardware's "teeth" in different ways and with different levels of effectiveness. We know that brushing at home with a simple toothbrush is convenient and has a different level of impact vs. getting your teeth cleaned at the dentist. In the same way, there are some approaches to biological reduction that may require simple tools or more complex implementation approaches (think about sonicating or just soaking your dentures, vs. brushing them). There are also some that are more effective for different degrees of cleanliness and still some that have materials compatibility concerns. In this article, we review known and NASA-certified approaches for biological reduction, pointing out materials compatibility concerns and areas where additional research is needed.

Pugel, D. E. (Betsy)↗

NASA NTRS2017

Brushing Your Spacecrafts Teeth: A Review of Biological Reduction Processes for Planetary Protection Missions

Much like keeping your teeth clean, where you brush away biofilms that your dentist calls plaque, there are various methods to clean spaceflight hardware of biological contamination, known as biological reduction processes. Different approaches clean your hardwares teeth in different ways and with different levels of effectiveness. We know that brushing at home with a simple toothbrush is convenient and has a different level of impact vs. getting your teeth cleaned at the dentist. In the same way, there are some approaches to biological reduction that may require simple tools or more complex implementation approaches (think about sonicating or just soaking your dentures, vs. brushing them). There are also some that are more effective for different degrees of cleanliness and still some that have materials compatibility concerns. In this article, we review known and NASA-certified approaches for biological reduction, pointing out materials compatibility concerns and areas where additional research is needed.

Pugel, D.E. (Betsy)↗

NASA NTRS1985

Study of meshing of beveled gears with normally decreasing arc teeth

The meshing of beveled gears was studied by the direct and inverse approaches. Gear wheels with teeth of equal height are studied, and wheels with normally-decreasing arc teeth. Different coordinate systems are utilized to plot the determination of the rotation of the originating gear wheel and the meshing line of the gear wheel which is cut. Matrices are used to determine the equations of the originating surfaces and the unit vectors of the normals to these originating surfaces.

Litvin, F. L.↗

NASA NTRS1984

A computer aided design procedure for generating gear teeth

A procedure for computer aided design (CAD) of gear teeth is presented. It is developed for generated teeth fabricated by a hob cutter or a shaper. It provides a means for analytically and numerically determining the tooth profile, given the cutter profile. An illustrative example with involute tooth profiles is given. Application with non-standard profiles and with bevel, spiral bevel, and hypoid gears is discussed.

Chang, S. H.↗

NASA NTRS1987

A simplified computer solution for the flexibility matrix of contacting teeth for spiral bevel gears

A computer code, FLEXM, was developed to calculate the flexibility matrices of contacting teeth for spiral bevel gears using a simplified analysis based on the elementary beam theory for the deformation of gear and shaft. The simplified theory requires a computer time at least one order of magnitude less than that needed for the complete finite element method analysis reported earlier by H. Chao, and it is much easier to apply for different gear and shaft geometries. Results were obtained for a set of spiral bevel gears. The teeth deflections due to torsion, bending moment, shearing strain and axial force were found to be in the order 10(-5), 10(-6), 10(-7), and 10(-8) respectively. Thus, the torsional deformation was the most predominant factor. In the analysis of dynamic load, response frequencies were found to be larger when the mass or moment of inertia was smaller or the stiffness was larger. The change in damping coefficient had little influence on the resonance frequency, but has a marked influence on the dynamic load at the resonant frequencies.

Hsu, C. Y.↗

NASA NTRS1965

Device measures curved surface finish on gear teeth

Measurement of the curved surface finish on gear teeth is made by a device used in conjunction with a conventional profilometer.

Source record↗

NASA NTRS1979

Incorporation of glycine-2-C-14 in acid-insoluble proteins of rat bones and teeth during hypokinesia and administration of thyrocalcitonine

A forced limitation of the motor activity in rats (from 5 to 60 days) results in reduced incorporation of glycine 2-C14 in the total acid insoluble proteins of limb bones and its increase in the teeth and mandibular-maxillary bones. Daily administration of five micrograms of thyrocalcitonine together with polyvinylpyrrolidone normalizes the protein metabolism in the bone tissues during the 40 days of experimentation.

Volozhin, A. I.↗

NASA NTRS1990

Modification Of Gear Teeth To Reduce Vibrations

Computer simulations yield data useful in designing for low noise. Effects of modifications in shape of gear teeth upon static transmission error and dynamic loading of gears now analyzed systematically. Design curves generated by conducting numerical simulations of dynamic effects at successive incremental modifications of gear systems operated at various applied loads. Modifications that result in minimum dynamic effect determined from design curves.

Townsend, Dennis P.↗

NASA NTRS1991

A new procedure for calculating contact stresses in gear teeth

A numerical procedure for evaluating and monitoring contact stresses in meshing gear teeth is discussed. The procedure is intended to extend the range of applicability and to improve the accuracy of gear contact stress analysis. The procedure is based upon fundamental solution from the theory of elasticity. It is an iterative numerical procedure. The method is believed to have distinct advantages over the classical Hertz method, the finite-element method, and over existing approaches with the boundary element method. Unlike many classical contact stress analyses, friction effects and sliding are included. Slipping and sticking in the contact region are studied. Several examples are discussed. The results are in agreement with classical results. Applications are presented for spur gears.

Somprakit, Paisan↗

NASA NTRS1991

Contact stresses in gear teeth: A new method of analysis

A new, innovative procedure called point load superposition for determining the contact stresses in mating gear teeth. It is believed that this procedure will greatly extend both the range of applicability and the accuracy of gear contact stress analysis. Point load superposition is based upon fundamental solutions from the theory of elasticity. It is an iterative numerical procedure which has distinct advantages over the classical Hertz method, the finite element method, and over existing applications with the boundary element method. Specifically, friction and sliding effects, which are either excluded from or difficult to study with the classical methods, are routinely handled with the new procedure. Presented here are the basic theory and the algorithms. Several examples are given. Results are consistent with those of the classical theories. Applications to spur gears are discussed.

Somprakit, Paisan↗

NASA NTRS1991

Contact stresses in gear teeth - A new method of analysis

A new, innovative procedure called point load superposition for determining the contact stresses in mating gear teeth is presented. It is believed that this procedure will greatly extend both the range of applicability and the accuracy of gear contact stress analysis. Point load superposition is based upon fundamental solutions from the theory of elasticity. It is an iterative numerical procedure which has distinct advantages over the classical Hertz method, the finite element method, and over existing applications with the boundary element method. Specifically, friction and sliding effects, which are either excluded from or difficult to study with the classical methods, are routinely handled with the new procedure. Presented here are the basic theory and the algorithms. Several examples are given. Results are consistent with those of the classical theories. Applications to spur gears are discussed.

Somprakit, Paisan↗

NASA NTRS1992

A basis for solid modeling of gear teeth with application in design and manufacture

A new approach to modeling gear tooth surfaces is discussed. A computer graphics solid modeling procedure is used to simulate the tooth fabrication process. This procedure is based on the principles of differential geometry that pertain to envelopes of curves and surfaces. The procedure is illustrated with the modeling of spur, helical, bevel, spiral bevel, and hypoid gear teeth. Applications in design and manufacturing are discussed. Extensions to nonstandard tooth forms, to cams, and to rolling element bearings are proposed.

Huston, Ronald L.↗

NASA NTRS1994

Numerical Simulation Of Cutting Of Gear Teeth

Shapes of gear teeth produced by gear cutters of specified shape simulated computationally, according to approach based on principles of differential geometry. Results of computer simulation displayed as computer graphics and/or used in analyses of design, manufacturing, and performance of gears. Applicable to both standard and non-standard gear-tooth forms. Accelerates and facilitates analysis of alternative designs of gears and cutters. Simulation extended to study generation of surfaces other than gears. Applied to cams, bearings, and surfaces of arbitrary rolling elements as well as to gears. Possible to develop analogous procedures for simulating manufacture of skin surfaces like automobile fenders, airfoils, and ship hulls.

Oswald, Fred B.↗