Search NASA⌕ Search

SEARCH · Search NASA

Results for “thermal annealing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

In Situ Characterization of Ferroelectric HfO 2 During Rapid Thermal Annealing

Thermal annealing is critical in governing the phase distribution, and ultimately the electrical properties, of ferroelectric hafnium oxide films. In particular, rapid thermal annealing (RTA) has been shown to favor the formation of ferroelectric crystal phases, but the dynamic behavior of the film over the course of the anneal is not well understood. Herein, synchrotron X-ray diffraction is used to characterize the phase distribution of HfO 2 films deposited by atomic layer deposition (ALD) in situ during RTA, revealing complex phase transformations occurring on the scale of seconds. All samples investigated here transform into a nonmonoclinic phase, which is required for ferroelectric films. However, this phase often converts into the more stable monoclinic phase as annealing proceeds. The kinetic barrier to the transformation to the monoclinic phase during heating is higher than 1 eV f.u. -1 In this work, the initial crystallization into the ferroelectric phase and relatively high barrier to transformation to the nonferroelectric phase suggests that careful control of the thermal annealing profile can greatly increase the ferroelectric fraction of the film. By using a fast ramp rate and a short annealing time above the ferroelectric crystallization temperature, the remanent polarization of a pure HfO 2 film can be increased more than twofold.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Relationship between microstructure evolution and properties enhancement of carbon nanotubes‐filled polybutylene terephthalate/polypropylene blends induced by thermal annealing

Abstract Thermal annealing induced microstructure evolution and properties enhancement of polybutylene terephthalate/polypropylene/carbon nanotubes (PBT/PP/CNTs) nanocomposites was methodically investigated. The electrical conductive PBT/PP/CNTs nanocomposites with a low percolation threshold were obtained by simple melt blending due to the selective location of the CNTs in PBT phase and the formation of the double percolation structure. Thermal annealing further remarkably decreased the volume resistivity of the nanocomposites, with the maximum reduction of seven orders of magnitude. Scanning electron microscope observation and rheology tests demonstrated that the relatively large CNTs agglomerates were redistributed to build more homogeneous CNTs networks after annealing. The phase coalescence during annealing promoted the formation of the more perfect co‐continuous structure. These phenomena helped to enhance the electrical conductivity of the nanocomposites. Flexural properties of the nanocomposites were also enhanced after annealing, which might be due to the more effective stress transfer between the polymer and CNTs induced by the reconstructed CNTs networks. The nanocomposites obtained in this study possess excellent electrical and mechanical properties, which can be applied to the fields of sensors, electromagnetic interference shielding, anti‐static materials, and so forth.

Shang, Mengyao↗
DOE OSTI2020

Fabrication of flexible perovskite solar cells via rapid thermal annealing

Adaptability, lightweight, and low cost of materials make flexible perovskite solar cells essential for the perovskite technology to breach commercial photovoltaic markets. Roll-to-roll manufacturing has great potential for high-throughput perovskite manufacturing; however, conventional annealing methods are not capable of producing flexible perovskite solar cells at scale. Conventional methods are time consuming and may compromise functionality of flexible substrates under tension. Here, we introduce a bladecoated perovskite thin film on flexible ITO-coated PET annealed via rapid thermal annealing (RTA) that reduces post-deposition processing time from ~150 s to ~14 s. As a result, performance was not sacrificed for scalability as a perovskite solar cell was produced with a power conversion efficiency (PCE) of 14.58%.

14 SOLAR ENERGY↗
DOE OSTI2020

Modification of magnetic ground state in Tb 2 Ni 0.90 Si 2.94 by thermal annealing

In this work, we have investigated the thermal annealing effect on the physical properties of an AlB 2 -type ternary intermetallic compound, Tb 2 Ni 0.90 Si 2.94 , that undergoes spin freezing behaviour coexisting with spatially limited antiferromagnetic phase below 9.9 K in as-cast form. Thermal annealing effect is found to result in considerable changes in the magnetic ground state properties of the system. Though only one magnetic transition around 9.9 K is observed for as-cast compound, the annealed sample exhibits two distinct magnetic transitions; one around T N ~ 13.5 K and another around T f ~ 4 K. The magnetization measurements and zero field neutron diffraction study reveal that the high temperature transition is antiferromagnetic type, though of limited correlation length, while the low temperature transition corresponds to spin freezing behaviour. The ac susceptibility and heat capacity studies also confirm the existence of frustrated cluster glass state at lower temperature than the antiferromagnetic ordering temperature. Additionally, ac susceptibility data exhibits signature of an additional peak in the even lower temperature region (at 2.2 K for zero frequency) that tends to shift in opposite direction with frequency in contrast to that observed for conventional glassy transitions. The change in intrinsic local structural disorder of Ni and Si ions associated with annealing has been argued to be responsible for the different magnetic behaviour in as-cast and annealed samples.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Pressure and thermal annealing effects on the photoconversion efficiency of polymer solar cells

This paper presents the results of experimental and theoretical studies of the effects of pressure and thermal annealing on the photo-conversion efficiencies (PCEs) of polymer solar cells with active layers that consist of a mixture of poly(3-hexylthiophene-2,5-diyl) and fullerene derivative (6,6)-phenyl-C 61 -butyric acid methyl ester. The PCEs of the solar cells increased from ~2.3% (for the unannealed devices) to ~3.7% for devices annealed at ~150 °C. A further increase in thermal annealing temperatures (beyond 150 °C) resulted in lower PCEs. Further improvements in the PCEs (from ~3.7% to ~5.4%) were observed with pressure application between 0 and 8 MPa. However, a decrease in PCEs was observed for pressure application beyond 8 MPa. The improved performance associated with thermal annealing is attributed to changes in the active layer microstructure and texture, which also enhance the optical absorption, mobility, and lifetime of the optically excited charge carriers. The beneficial effects of applied pressure are attributed to the decreased interfacial surface contacts that are associated with pressure application. The implications of the results are then discussed for the design and fabrication of organic solar cells with improved PCEs.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Considerations for Thermal Annealing of Zr-Alloy Cladding During Dry Storage

In January 2025, the U.S. Department of Energy (DOE) sponsored a technical workshop with fuel vendors that provided a forum for increased collaboration on backend fuel cycle research. The workshop reviewed observations of thermal annealing of irradiated zirconium alloys in simulated dry storage conditions and discussed implications to the industry’s interest in reducing wet storage to optimize operational flexibility and the expected trend of increasing discharge burnup (and decay heats), which could lead to an increase in dry storage temperatures. One approach to accommodate increased decay heats in dry storage is to increase the regulatory temperature limit during dry storage, which is now 400°C. However, this could lead to thermal annealing of the cladding, which will tend to increase creep rates, creep strains, and ductility while decreasing yield strength. These considerations are compounded by bonding between the pellet and cladding at high burnup, which results in the pellet carrying more load during fuel rod deformations, especially in bending, which is the dominant deformation phenomenon in canister drop analyses. Because the U.S. Nuclear Regulatory Commission (NRC) recommends yield strength as a primary failure criterion for accident analyses in storage and transportation, particularly for canister drop scenarios, the purpose of the workshop was to develop options for alternative failure criterion that could replace yield strength in canister drop analyses. Topics discussed were (1) the regulatory framework, (2) the effect of thermal annealing on microhardness and tensile properties of cladding materials, (3) the effect of thermal annealing on fuel rod failure during bending, bending fatigue, and pinch loading, and (4) an alternative failure criterion for canister drop analyses. This paper provides a summary of the key discussions and outcomes of the workshop

Cantonwine, Paul [ORNL] (ORCID:0009000522247033)↗
NASA NTRS1990

Chemical nature of silicon nitride-indium phosphide interface and rapid thermal annealing for InP MISFETs

A rapid thermal annealing (RTA) process in pure N2 or pure H2 was developed for ion-implanted and encapsulated indium phosphide compound semiconductors, and the chemical nature at the silicon nitride-InP interface before and after RTA was examined using XPS. Results obtained from SIMS on the atomic concentration profiles of the implanted silicon in InP before and after RTA are presented, together with electrical characteristics of the annealed implants. Using the RTA process developed, InP metal-insulator semiconductor FETs (MISFETS) were fabricated. The MISFETS prepared had threshold voltages of +1 V, transconductance of 27 mS/mm, peak channel mobility of 1200 sq cm/V per sec, and drain current drift of only 7 percent.

Biedenbender, M. D.↗
DOE OSTI2021

Enhanced Guest@MOF Interaction via Stepwise Thermal Annealing: TCNQ@Cu 3 (BTC) 2

Confinement of guest molecules in porous materials such as metal organic frameworks (MOFs) promises to deliver emergent properties separate from those of the individual components. Understanding the confinement mechanism is therefore important for the development of new synthesis routes that adjust MOF properties for specific applications. In this work, we developed a new synthetic method to confine guest molecules into MOF pores through a stepwise thermal annealing process, wherein the confinement of 7,7,8,8-tetracyanoquinodimethane (TCNQ) guest molecules into Cu 3 (BTC) 2 (BTC = benzene-1,3,5-tricarboxylic acid) MOF host is used as an example of how novel materials can be created with new physical properties. The stepwise thermal annealing process includes 1) an activation process of pristine Cu 3 (BTC) 2 MOF to maximizes the TCNQ guest loading in the MOF host by effectively removing the residual solvents and 2) post-annealing of the TCNQ infiltrated MOF to enhances the interaction of the confined guest molecules with the MOF host. Obtained experimental results based on thermogravimetric analysis, N 2 gas adsorption, electron microscopy, X-ray diffraction and infrared absorption, combined with density functional theory calculations provide evidence that the use of a stepwise thermal annealing process yields enhancements in the guest loading, packing and interaction between the TCNQ guest and the MOF host. The new hybrid TCNQ@Cu 3 (BTC) 2 system is stable and shows no significant signs of structural degradation even after submersion in water. This is due to the presence of significantly stronger interactions of TCNQ with the frame-work metal ions compared to those of the water molecules competing for the same framework binding sites. It was also found that TCNQ@Cu 3 (BTC) 2 system maintains a significant CO 2 and CH 4 adsorption potential compared to the pristine MOF. The synthetic route developed in this work yields novel guest@MOF hybrid systems that will be useful for many MOF-based applications such as gas separations and chemical sensors performed under humid conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Role of Postdeposition Thermal Annealing on Intracrystallite and Intercrystallite Structuring and Charge Transport in Poly(3-hexylthiophene)

The performance of electronic devices comprising conjugated polymers as the active layer depends not only on the intrinsic characteristics of the materials but also on the details of the extrinsic processing conditions. Here, we examine the effect of postdeposition thermal treatments on the microstructure of poly(3-hexylthiophene) (P3HT) thin films and its impact on their electrical properties. Unsurprisingly, we find thermal annealing of P3HT thin films to generally increase their crystallinity and crystallite coherence length while retaining the same crystal structure. Despite such favorable structural improvements of the polymer active layers, however, thermal annealing at high temperatures can lead to a net reduction in the mobility of transistors, implicating structural changes in the intercrystallite amorphous regions of these semicrystalline active layers take place on annealing, and the simplistic picture that crystallinity governs charge transport is not always valid. Our results instead suggest tie-chain pullout, which occurs during crystal growth and perfection upon thermal annealing to govern charge transport, particularly in low-molecular-weight systems in which the tie-chain fraction is low. By demonstrating the interplay between intracrystallite and intercrystallite structuring in determining the macroscopic charge transport, we shed light on how structural evolution and charge-transport properties of nominally the same polymer can vary depending on the details of processing.

36 MATERIALS SCIENCE↗
NASA NTRS1989

Thermal annealing of GaAs concentrator solar cells

The thermal annealing of GaAs concentrator cells after electron irradiation is reported. Results are given for cells annealed at 150, 200, and 250 C. Isochronal annealing was done for 20 min intervals up to 350 C. For cells irradiated with electrons of energies between 0.7 and 2.3 MeV, the recovery decreases with increasing electron energy. Isothermal and isochronal annealing produce the same recovery. Cells irradiated to 3 x 10 to the 15th or 1 x 10 to the 16th e/sq cm recover to similar unannealed fractions. Significant annealing is seen starting at 150 C, although very long times are required.

Curtis, H. B.↗
DOE OSTI2022

Microstructural changes in nuclear graphite induced by thermal annealing

Irradiation-induced property change in nuclear graphite is particularly important when considering the in-service lifetimes of graphite components. In other works, it has been shown that annealing of irradiated graphite above the irradiation temperature may heal atomic-level defects and thus reverse some amount of physical property change. In this work, virgin nuclear graphite IG-110 was annealed at 2500°C to observe any microstructural changes due solely to high-temperature thermal annealing. We report the results shown in this study suggest that fullerene-like defects will arise due to thermal annealing near graphitization temperature. Consequently, such defects may directly contribute to non-recoverable physical property change which has previously been observed in irradiated nuclear graphites.

36 MATERIALS SCIENCE↗