Search NASA⌕ Search

SEARCH · Search NASA

Results for “thrust distribution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1945

Effect of Propeller-Axis Angle of Attack on Thrust Distribution over the Propeller Disk in Relation to Wake-Survey Measurement of Thrust

Tests were made to investigate the variation of thrust distribution over the propeller disk with angle of pitch of the propeller thrust axis and to determine the disposition and the minimum number of rakes necessary to measure the propeller thrust. The tests were made at a low Mach number for a low and a high blade angle with the propeller operating at three small angles of pitch, and some of the tests were repeated at a higher Mach number. The data obtained show that, for small angles of pitch, large changes occur in the energy distribution in the wake which prohibit the use of a single survey rake for thrust measurement in flight tests and limit the use of a single rake in wind-tunnel tests. Under certain conditions, the energy distribution in the wake took on a symmetrical form and two diametrically opposed survey rakes were shown to be satisfactory for obtaining propeller thrust. (author)

Pendley, Robert E↗
NASA NTRS1927

Calculating thrust distribution and efficiency of air propellers

I am now proposing a method for the preliminary approximate calculation of the thrust distribution and efficiency of air propellers under any operating conditions. Our task becomes the following, namely, to determine the speed relations and the forces developed on a section with a given direction and velocity of the air current, a problem which can be solved with the aid of the momentum theory.

PROPELLERS - DESIGN & THEORY↗
NASA NTRSDate not supplied

Distributed Thrust Takeoff for the NASA X-57 Mod IV Flight Demonstrator

The Mod IV configuration of the X-57 flight demonstrator concept featured two forms of distributed electric propulsion—one cruise propulsor at each wingtip for primary propulsion that enabled favorable interaction with the wingtip vortex, and six high-lift propulsors distributed along the leading edge of each wing to enhance low-speed flight characteristics. The power system that fed these propulsors was arranged in two independent power buses. This unique arrangement did not lend itself to traditional “one engine inoperative” methods for determining performance after a critical failure in the propulsion system. Several potential failure scenarios were identified as potential “critical loss of thrust” events, and experiments that included pilot-in-the-loop simulation with the project test pilots were conducted to determine if these events would result in adequate handling and performance. Prior research showed that a total failure of one of the cruise motors during takeoff or initial climb could result in unacceptable performance for a traditional full-power takeoff. A new technique dubbed Distributed Thrust Takeoff (DiTTo) was developed to reduce the impact of the thrust asymmetry and total loss of thrust that could occur in any of the critical loss of thrust scenarios. The results showed that adequate performance and handling qualities could be achieved in each of the critical failure scenarios when using the DiTTo technique.

Distributed Propulsion↗
NASA NTRSDate not supplied

Distributed Thrust Takeoff for the NASA X-57 Mod IV Flight Demonstrator

The Mod IV configuration of the X-57 flight demonstrator concept featured two forms of distributed electric propulsion—one cruise propulsor at each wingtip for primary propulsion that enabled favorable interaction with the wingtip vortex, and six high-lift propulsors distributed along the leading edge of each wing to enhance low-speed flight characteristics. The power system that fed these propulsors was arranged in two independent power buses. This unique arrangement did not lend itself to traditional “one engine inoperative” methods for determining performance after a critical failure in the propulsion system. Several potential failure scenarios were identified as potential “critical loss of thrust” events, and experiments that included pilot-in-the-loop simulation with the project test pilots were conducted to determine if these events would result in adequate handling and performance. Prior research showed that a total failure of one of the cruise motors during takeoff or initial climb could result in unacceptable performance for a traditional full-power takeoff. A new technique dubbed Distributed Thrust Takeoff (DiTTo) was developed to reduce the impact of the thrust asymmetry and total loss of thrust that could occur in any of the critical loss of thrust scenarios. The results showed that adequate performance and handling qualities could be achieved in each of the critical failure scenarios when using the DiTTo technique.

Distributed Propulsion, Electric Propulsion, Criti↗
NASA NTRS1942

Contribution to the ideal efficiency of screw propellers

The stipulation of best thrust distribution is applied to the annular elements of the screw propeller with infinitely many blades in frictionless, incompressible flow and an ideal jet propulsion system derived possessing hyperbolic angular velocity distribution along the blade radius and combining the advantage of uniform thrust distribution over the section with minimum slipstream and rotation losses. This system is then compared with a propeller possessing the same angular velocity at all blade elements and the best possible thrust distribution secured by means of an induced efficiency varying uniformly over the radius. Lastly, the case of the lightly loaded propeller also is discussed.

Hoff, Wilhelm↗
NASA NTRS1972

Leading-edge force features of the aerodynamic finite element method.

Description of a practical procedure for computing the wing leading-edge thrust distribution by the finite element method. When incorporated into a wing-body aerodynamic computer program, the technique is capable of predicting (at subsonic and supersonic speeds) the leading-edge thrust distribution (and therefore, the lateral-directional stability derivatives due to roll) and the nonlinear aerodynamic characteristics of low aspect-ratio wings with leading edge separation due to the application of suction technology.

Lan, C.-T.↗
NASA NTRS2018

Design of Distributed Mail-Slot Propulsion System on a Hybrid Wingbody Aircraft

This paper deals with designing a thrust distribution strategy when a Turboelectric Distributed Propulsion (TeDP) system of 16 embedded propulsors is installed on an aerodynamically optimized hybrid wing-body configuration. This HWB previously designed to satisfy conditions of trim, longitudinally static stability and specific cargo space is employed as the baseline configuration for the current study of seeking an optimal propulsion/power system. According to the nature of the entrance flow condition for each distributed propulsion passage in hybrid wing-body aircraft, the ingested boundary layer thickness differs and results in different propulsive reaction. An optimal distribution of thrust and power output is determined by how the system utilizes the propulsive characteristics of each passage. The design space and the number of design variables are selected and described accordingly. An actuator disk model is employed to model thrust generation and shaft power from the propulsor. To carry out the optimization of the propulsion/power system on a computationally expensive CFD model, a Kriging method in conjunction with a Genetic Algorithm (GA) is applied. Throughout the design process, the propulsion performances of the sampled propulsion/power system are analyzed and compared to those of a clean flow engine. The performance metrics includes mass flow rate, fan pressure ratio besides the thrust and shaft power. Minimization of total shaft power from the distributed engine is performed at multiple thrust levels. The benefit of boundary layer ingestion propulsion system is quantified via comparison of thrust equivalent, shaft power and mass flow equivalent clean flow engines with CFD based system design.

Hybrid Wingbody↗
NASA NTRS1982

Measurements of energy distribution and thrust for microwave plasma coupling of electrical energy to hydrogen for propulsion

A microwave plasma system for transfer of electrical energy to hydrogen flowing through the system has potential application for coupling energy to a flowing gas in the electrothermal propulsion concept. Experimental systems have been designed and built for determination of the energy inputs and outputs and thrust for the microwave coupling of energy to hydrogen. Results for experiments with pressure in the range 100 microns-6 torr, hydrogen flow rate up to 1000 micronmoles/s, and total absorbed power to 700 w are presented.

Morin, T.↗
NASA NTRS1972

Simulation study of the lift roll coupling problem for hovering VTOL aircraft

The effects of lift-roll coupling on the handling qualities of hovering VTOL aircraft using differential thrust for roll control were assessed in a piloted simulation study in the Ames six-degrees-of-freedom motion simulator. The configuration tested has three vertical thrust sources, one on the roll axis and two laterally displaced from the roll axis, with a thrust distribution of 25%/50%/25%. The outboard thrust sources were modulated to provide roll control whereas all three provided height control. Maximum thrust-to-weight ratio was varied together with a coupling parameter that combined roll-inertia, weight, and engine location. Results showed that handling qualities are affected not only by the occurrence of lift-roll coupling (dependent on both variables) but also by the severity of the coupling (dependent on the coupling parameter alone). However, the advantages of differential thrust for control can be retained with careful design.

Jacobsen, R. A.↗
NASA NTRS1980

Supersonic wings with significant leading-edge thrust at cruise

Experimental/theoretical correlations are presented which show that significant levels of leading-edge thrust are possible at supersonic speeds for certain planforms having the geometry to support the theoretical thrust-distribution potential. The new analytical process employed provides not only the level of leading-edge thrust attainable but also the spanwise distribution of both it and that component of full theoretical thrust which acts as vortex lift. Significantly improved aerodynamic performance in the moderate supersonic speed regime is indicated.

Robins, A. W.↗
NASA NTRS1980

Supersonic wings with significant leading-edge thrust at cruise

Experimental/theoretical correlations are presented which show that significant levels of leading edge thrust are possible at supersonic speeds for certain planforms which match the theoretical thrust distribution potential with the supporting airfoil geometry. The analytical process employed spanwise distribution of both it and/or that component of full theoretical thrust which acts as vortex lift. Significantly improved aerodynamic performance in the moderate supersonic speed regime is indicated.

Robins, A. W.↗
NASA NTRS1991

An assessment of current methods for drag-due-to-lift minimization at supersonic speeds

The estimation and minimization of drag-due-to-lift at supersonic speeds has been examined in this study. Correlations of theory with experimental data are used to assess the applicability and limitations of the linearized theory. The role of leading-edge thrust and the use of twist and camber to develop distributed thrust are also discussed. A semiempirical design and estimation method which takes into account the shortcomings of the linear theory is presented. The use of this method will allow the design of more nearly optimum lifting surfaces and provide an accurate prediction of their level of performance. A preliminary examination is made of the use of an Euler code for estimation of the aerodynamic characteristics of a twisted and cambered wing.

Mann, Michael J.↗
NASA NTRS1960

Performance of Several Conical Convergent-Divergent Rocket-Type Exhaust Nozzles

An investigation was conducted to obtain nozzle performance data with relatively large-scale models at pressure ratios as high as 120. Conical convergent-divergent nozzles with divergence angles alpha of 15, 25, and 29 deg. were each tested at area ratios of approximately 10, 25, and 40. Heated air (1200 F) was supplied at the nozzle inlet at pressures up to 145 pounds per square inch absolute and was exhausted into quiescent air at pressures as low as 1.2 pounds per square inch absolute. Thrust ratios for all nozzle configurations are presented over the range of pressure ratios attainable and were extrapolated when possible to design pressure ratio and beyond. Design thrust ratios decreased with increasing nozzle divergence angle according to the trend predicted by the (1 + cos alpha)/2 parameter. Decreasing the nozzle divergence angle resulted in sizable increases in thrust ratio for a given surface-area ratio (nozzle weight), particularly at low nozzle pressure ratios. Correlations of the nozzle static pressure at separation and of the average static pressure downstream of separation with various nozzle parameters permitted the calculation of thrust in the separated-flow region from unseparated static-pressure distributions. Thrust ratios calculated by this method agreed with measured values within about 1 percent.

Campbell, C. E.↗
NASA NTRS2008

Distributed Turboelectric Propulsion for Hybrid Wing Body Aircraft

Meeting future goals for aircraft and air traffic system performance will require new airframes with more highly integrated propulsion. Previous studies have evaluated hybrid wing body (HWB) configurations with various numbers of engines and with increasing degrees of propulsion-airframe integration. A recently published configuration with 12 small engines partially embedded in a HWB aircraft, reviewed herein, serves as the airframe baseline for the new concept aircraft that is the subject of this paper. To achieve high cruise efficiency, a high lift-to-drag ratio HWB was adopted as the baseline airframe along with boundary layer ingestion inlets and distributed thrust nozzles to fill in the wakes generated by the vehicle. The distributed powered-lift propulsion concept for the baseline vehicle used a simple, high-lift-capable internally blown flap or jet flap system with a number of small high bypass ratio turbofan engines in the airframe. In that concept, the engine flow path from the inlet to the nozzle is direct and does not involve complicated internal ducts through the airframe to redistribute the engine flow. In addition, partially embedded engines, distributed along the upper surface of the HWB airframe, provide noise reduction through airframe shielding and promote jet flow mixing with the ambient airflow. To improve performance and to reduce noise and environmental impact even further, a drastic change in the propulsion system is proposed in this paper. The new concept adopts the previous baseline cruise-efficient short take-off and landing (CESTOL) airframe but employs a number of superconducting motors to drive the distributed fans rather than using many small conventional engines. The power to drive these electric fans is generated by two remotely located gas-turbine-driven superconducting generators. This arrangement allows many small partially embedded fans while retaining the superior efficiency of large core engines, which are physically separated but connected through electric power lines to the fans. This paper presents a brief description of the earlier CESTOL vehicle concept and the newly proposed electrically driven fan concept vehicle, using the previous CESTOL vehicle as a baseline.

Kim, Hyun Dae↗
NASA NTRSDate not supplied

Flight Deck Design of a Hybrid Turbine/Electric Aircraft

The SUbsonic Single Aft eNgine (SUSAN) program is being developed as a sustainable subsonic regional aircraft. NASA is conducting trade studies for this future hybrid single aisle passenger aircraft. The goal of reducing emission levels by 50% will be enabled through an advanced design. An aft mounted single turbine engine provides thrust and electric power to drive 16 wing mounted electric engines. Using the 16 counter-rotating electric fans will create an efficient, very high bypass ratio, engine. Electric engines allow for distributed thrust, reducing control surfaces and provide a greater dynamic response. Batteries provide boost for takeoff and climb, allowing a smaller, more efficient, turbine engine. As part of the SUSAN effort, two pilot-in-the-loop studies were conducted at NASA Langley Research Center in Virginia to explore flight deck design issues. In particular: how many throttles are required/desired for a 17-engine aircraft, does the hybrid electric design change the answer, what are the requirements for electric engine displays, what system pages are required, and what information is required to monitor the batteries. Objective and subjective data were collected after each scenario and at the end of the day with a guided set of questionnaires from sixteen crews paired by airline. Data along with pilot comments were used to improve the throttle and engine displays between the studies and used to make the final recommendations on flight deck configurations. This paper provides final design recommendations for the SUSAN flight deck and justification for each recommendation.

PAI↗
NASA NTRS1996

Aeroacoustic Characteristics of a Rectangular Multi-Element Supersonic Jet Mixer-Ejector Nozzle

This paper provides a unique, detailed evaluation of the acoustics and aerodynamics of a rectangular multi-element supersonic jet mixer-ejector noise suppressor. The performance of such mixer-ejectors is important in aircraft engine application for noise suppression and thrust augmentation. In contrast to most prior experimental studies on ejectors that reported either aerodynamic or acoustic data, our work documents both types of data. We present information on the mixing, pumping, ejector wall pressure distribution, thrust augmentation and noise suppression characteristics of four simple, multi-element, jet mixer-ejector configurations. The four configurations included the effect of ejector area ratio (AR = ejector area/primary jet area) and the effect of non-parallel ejector walls. We also studied in detail the configuration that produced the best noise suppression characteristics. Our results show that ejector configurations that produced the maximum maximum pumping (entrained flow per secondary inlet area) also exhibited the lowest wall pressures in the inlet region, and the maximum thrust augmentation. When cases having the same total mass flow were compared, we found that noise suppression trends corresponded with those for pumping. Surprisingly, the mixing (quantified by the peak Mach number, and flow uniformity) at the ejector exit exhibited no relationship to the noise suppression at moderate primary jet fully expanded Mach numbers (Mj is less than 1.4). However, the noise suppression dependence on the mixing was apparent at higher Mj. The above observations are justified by noting that the mixing at the ejector exit is ot a strong factor in determining the radiated noise when noise produced internal to the ejector dominates the noise field outside the ejector.

Raman, Ganesh↗