Search NASA⌕ Search

SEARCH · Search NASA

Results for “trench”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Installation of Lysimeters Near Engineered Trench 3, Slit Trench 8, and Slit Trench 9

Nine new lysimeter stations were installed at the E-Area Low Level Waste Facility (ELLWF). Six lysimeter stations were installed near Engineered Trench 3 (ET3), one installed near Slit Trench 8 (ST8), and two installed near Slit Trench 9 (ST9) as shown in Figure ES-1. Two lysimeters were installed at each station at the depths shown in Table ES-1. Lysimeter placements were based on borehole lithology and were comparable to existing nearby lysimeter stations. The deepest lysimeter at each of the new lysimeter stations was designated as the action-level lysimeter. Following installation, the lysimeters were purged and placed under vacuum for sampling. Sampling occurred in April 2023. Analytical results from the sampling will be provided in the Spring 2023 Lysimeter Tritium Data technical memo and the 2023 Annual Summary Report. With the addition of the new lysimeters at ET3, ST8, and ST9, the vadose zone monitoring system is now comprised of 327 active lysimeters at 111 lysimeter stations. There are 102 action-level lysimeters at 111 stations.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

A tutorial on the micro-trench technique for incident ion angle, material erosion, and impurity deposition measurements at plasma-facing surfaces

The micro-trench method is a new technique to measure polar and azimuthal incident ion angles, material erosion, and impurity deposition at plasma-facing surfaces, and has been applied in the DIII-D divertor. This article gives a tutorial of the micro-trench technique consisting of six steps: (1) micro-trench fabrication, (2) pre-exposure measurement of the fabricated micro-trench geometry, (3) tracer material deposition, (4) plasma exposure, (5) post-exposure observation of the tracer material, and (6) post-exposure measurement of the micro-trench geometry. Two criteria need to be satisfied to apply the micro-trench method successfully: (i) uniform impurity deposition on the micro-trench floor, and (ii) erosion dominated by the physical sputtering induced by the impinging ions. Furthermore, when those two criteria are satisfied, post-exposure analysis of the impurity deposition patterns on the micro-trench floor may be used to determine the polar and azimuthal incident ion directions (mean values of the ion angle directions), erosion rate, and impurity deposition rate during plasma exposure without computational interpretation.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Performance Assessment Maintenance Plan for the Active Low-Level Burial Ground Trenches 31, 34, and 94 at the Hanford Site

This report documents the maintenance plan for the Hanford Site 200 West Area Active Low-Level Burial Ground Trenches 31 and 34 and 200 East Area Active Trench 94 performance assessment (PA). The PA maintenance plan is one of several supporting documents that are compendiums to the active trenches (Trenches 31, 34, and 94) PA as required in DOE O 435.1, Radioactive Waste Management . The PA is documented in DOE/RL-2021-26, Performance Assessment of Active Trenches in 200 East and West Low-Level Burial Grounds at the Hanford Site . This plan follows the requirements and outline specified in the applicable U.S. Department of Energy (DOE) standard used for developing documents supporting DOE-STD-5002-2017, Disposal Authorization Statement and Tank Closure Documentation . This maintenance plan summarizes the following major activities DOE plans to conduct to maintain the Trenches 31, 34, and 94 PA: Monitoring; Research and development; Planned reviews and analyses; Revisions of Trenches 31, 34, and 94 PA. The planned research and development activities relate to evaluating the key assumptions, including evaluating conceptual model assumptions and parameter value assumptions used in the PA. The planned research and development activities include those that are designed to track the release mechanisms for Category 1, Category 3, and uranium billet waste sources, as well as continued characterization and related modeling of the natural environment in the Central Plateau of the Hanford Site. In addition, the planned research and development activities include focused testing and evaluation of engineered and natural materials to reduce the uncertainty in the conceptual models and parameter values used in the PA. All key and secondary issues identified during the review of the PA by the Low-Level Waste Disposal Facility Federal Review Group have been resolved prior to finalization of the PA. There are no outstanding issues.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Performance Assessment of the Active Trenches in 200 East and 200 West Low-Level Burial Grounds at the Hanford Site

The purpose of this document is to provide the assessment of the long-term human health and environmental risk associated with the continued disposal of radioactive wastes in the active trenches of the 200 East and 200 West Area Low-Level Burial Grounds (LLBGs) at the Hanford Site (Figure ES-1), as required by DOE O 435.1, Radioactive Waste Management1. Since July 1, 2004, the only active trenches in the 200 West Area LLBGs are the lined Trenches 31 and 34 used for the disposal of containerized low-level waste and mixed low-level waste (Figure ES-2). The only active trench in the 200 East Area LLBGs is the unlined Trench 94 that was used for the disposal of naval reactor compartments (Figure ES-3). Trenches 31 and 34 are intended to be used until they reach their disposal capacity while Trench 94 will be used and expanded as necessary to meet the needs of the U.S. Navy.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Performance Assessment Closure Plan for the Active Low-Level Burial Ground Trenches 31, 34, and 94 at the Hanford Site

This report documents the closure plan for the active trenches within the Low-Level Burial Grounds of the Hanford Site, namely Trenches 31 and 34 in the 200 West Area and Trench 94 in 200 East Area. This closure plan is developed to meet the requirements of DOE O 435.1, Radioactive Waste Management. It is one of the several technical basis documents, along with the performance assessment (DOE/RL-2021-26, Performance Assessment of Active Trenches in 200 East and West Low-Level Burial Grounds at the Hanford Site), which is required for maintaining the Operating Disposal Authorization Statement as described in DOE-STD-5002-2017, Disposal Authorization Statement and Tank Closure Documentation.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2026

Sapphire Substrate Trenching to Advance Superconducting High-Coherence Quantum Devices

Achieving longer coherence times in superconducting qubits is essential for advancing quantum information processing and enabling scalable quantum computing. This work presents an innovative fabrication strategy focused on sapphire trenching of the substrate of superconducting high-coherence quantum devices, developed by the SQMS Nanofabrication Taskforce in collaboration with the materials characterization team. In this talk, we present a method to efficiently and consistently trench into the sapphire substrate, without compromising the surface roughness or profile of the etched sapphire. In the literature, trenching in the substrate has been shown to decrease losses, unwanted coupling and thermal stress. Sapphire’s strong covalent bonds make it harder to etch compared to silicon, yet it is more favorable for high-coherence quantum devices due to its lower dielectric losses. This innovative technique opens new possibilities for superconducting qubit fabrication: we fabricated high coherence qubit chips on sapphire substrates with trenching, to demonstrate that it will help pushing towards higher coherence times. By integrating this work with ongoing junction process optimization, design innovation, materials characterization and exploration, we outline a clear pathway toward transmon coherence times reaching millisecond scales and beyond.

Garattoni, S. [Fermilab]↗
DOE OSTI2026

Sapphire Substrate Trenching to Advance Superconducting High-Coherence Quantum Devices

Achieving longer coherence times in superconducting qubits is essential for advancing quantum information processing and enabling scalable quantum computing. This work presents an innovative fabrication strategy focused on sapphire trenching of the substrate of superconducting high-coherence quantum devices, developed by the SQMS Nanofabrication Taskforce in collaboration with the materials characterization team. In this talk, we present a method to efficiently and consistently trench into the sapphire substrate, without compromising the surface roughness or profile of the etched sapphire. In the literature, trenching in the substrate has been shown to decrease losses, unwanted coupling and thermal stress. Sapphire’s strong covalent bonds make it harder to etch compared to silicon, yet it is more favorable for high-coherence quantum devices due to its lower dielectric losses. This innovative technique opens new possibilities for superconducting qubit fabrication: we fabricated high coherence qubit chips on sapphire substrates with trenching, to demonstrate that it will help pushing towards higher coherence times. By integrating this work with ongoing junction process optimization, design innovation, materials characterization and exploration, we outline a clear pathway toward transmon coherence times reaching millisecond scales and beyond.

Garattoni, S. [Fermilab]↗
DOE OSTI2024

Investigation on gate oxide reliability under gate bias screening for commercial SiC planar and trench MOSFETs

This paper evaluates the impact of the fast high gate-voltage screening technique on gate oxide reliability of commercial 1.2 kV 4H-SiC power metal-oxide-semiconductor field-effect transistors (MOSFETs) with planar and trench gate structures. The measurements are conducted on packaged devices with the intent that the results will be applicable to wafer-level screening. The threshold voltage (V th ) of SiC MOSFETs is measured before and after various screening treatments and recovery process. In addition, constant-voltage time-dependent dielectric breakdown (TDDB) measurements are performed on SiC MOSFETs to obtain the intrinsic lifetime of gate oxide. The objective of this study is to determine the optimal screening conditions and improve screening efficiency without degradation of gate oxide reliability, such as V th shift and reduced oxide intrinsic lifetime. Due to the differences in the gate oxidation process and structural design of SiC planar and trench MOSFETs, the two types of devices exhibit different oxide reliability in the screening process. The recommended screening conditions obtained in this paper reveal that SiC trench MOSFETs can accept higher screening voltages compared to SiC planar MOSFETs. Hence, it can be concluded that more efficient screening techniques can be adopted for SiC MOSFETs with thicker gate oxide to meet the requirements of industrial applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Diffused trenches for high fill-factor Low-Gain Avalanche Diodes

Low-Gain Avalanche Diodes (LGADs) are a class of silicon detectors that have been specifically designed for the fast detection of minimum ionizing particles (mips) in High-Energy Physics experiments. While they provide timing resolution on the order of a few tens of picoseconds, they cannot achieve high spatial resolution due to the intrinsic characteristics of their structures. Thus, active R&D is on-going to develop detectors based on LGADs to improve their spatial resolution while maintaining the timing performance of the LGADs. Such devices are, for example, AC-coupled LGADs and Deep-Junction LGADs. Another device option is the Trench-Isolated LGAD (TI LGAD), where trenches etched at the periphery of the pixels isolate them while providing a high fill-factor. Here, in this paper, we present a variation of this latter approach, demonstrating its feasibility by means of 2-dimensional TCAD simulations.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

β -Ga 2 O 3 trench Schottky diodes by low-damage Ga-atomic beam etching

β-Ga 2 O 3 trench Schottky barrier diodes fabricated through a Gallium atomic beam etching technique with excellent field strength and power device figure of merit are demonstrated. Trench formation was accomplished by a low-damage Ga flux etch that enables near-ideal forward operating characteristics that are independent of fin orientation. The reverse breakdown field strength of greater than 5.10 MV/cm is demonstrated at a breakdown voltage of 1.45 kV. This result demonstrates the potential for Ga atomic beam etching and high-quality dielectric layers for improved performance in β-Ga 2 O 3 vertical power devices.

42 ENGINEERING↗
DOE OSTI2025

Radionuclide Inventory Threshold for Trench 31 and 34 Located Within the 200 West Area Low-Level Burial Grounds

Trenches 31 and 34 located in the 200 West Area Low-Level Burial Ground (LLBG) are authorized for disposal of low-level and mixed low-level radioactive waste under DOE Order 435.1, Radioactive Waste Management. A revised Disposal Authorization Statement was issued in October 2023 following approval of the performance assessment (PA) and supporting technical basis documents. To be consistent with approved PA calculations, the waste acceptance criteria (WAC) needs to be updated to include concentration limits for Category 1 (CAT1) and Category 3 (CAT3) waste along with the inventory limits. This environmental calculation file (ECF) provides the inventory limits for Category 1 and Category 3 waste disposal of radionuclides at Trench 31 and 34 based on the PA calculations. The concentration limits are not calculated as they are provided in the PA itself. The inventory thresholds (or limits) are calculated for only those radionuclides that are identified in the PA as the primary dose contributors. The primary dose contributors for the groundwater pathway are technetium-99, iodine-129, niobium-94, chlorine-36, molybdenum-93, and niobium-93m while those for the air pathway are tritium and carbon-14.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

KBase Narrative - Atacama Trench & Sn Clemente 2018 cruise Metagenomes -Decontamination through Metagenomic Fractionation and analysis of Metabolic Potential-

Deep-sea microbiomes sampled with traditional or pressure-retaining instrumentation A fundamental property of life in the sea is that with increasing depth must come increased adaptation to elevated hydrostatic pressures. This project aims to assess technology for the accurate characterization of microbial biodiversity and biochemistry at greater depths, and validate its use in some of the deepest and least-explored waters in the Ocean: Hadal Trench. Compared to the 0.1 megapascal (MPa) of surface waters, organisms inhabiting at the average depth of the Ocean (3800 m) have to deal with pressures of 38 MPa (5,500 psi). The effects of these high pressure have been most thoroughly investigated in microorganisms, where it has been found to affect membrane integrity and transport, cytoskeletal assembly and both DNA and protein synthesis. We will explore the diversity and activity of microorganisms from 2000 m to >8,000 m depths within the highly productive water column of hadal trenches, comparing seawater samples obtained with and without substantial pressure changes during recovery. A pressure retaining device was used to sample the microbial communities of the watercolumn with reduced decompression during retreival (Peoples et. al., 2019). References: Peoples LM, Norenberg M, Price D, McGoldrick M, Novotny M, Bochdansky A, Bartlett DH. A full-ocean-depth rated modular lander and pressure-retaining sampler capable of collecting hadal-endemic microbes under in situ conditions. Deep Sea Research Part I: Oceanographic Research Papers. 2019 Jan 1;143:50-7.

Plominsky, Alvaro M.↗
DOE OSTI2024

KBase Narrative - Atacama Trench & Sn Clemente 2018 cruise Metagenomes -Sequence quality filtration & Assembly-

Deep-sea microbiomes sampled with traditional or pressure-retaining instrumentation A fundamental property of life in the sea is that with increasing depth must come increased adaptation to elevated hydrostatic pressures. This project aims to assess technology for the accurate characterization of microbial biodiversity and biochemistry at greater depths, and validate its use in some of the deepest and least-explored waters in the Ocean: Hadal Trench. Compared to the 0.1 megapascal (MPa) of surface waters, organisms inhabiting at the average depth of the Ocean (3800 m) have to deal with pressures of 38 MPa (5,500 psi). The effects of these high pressure have been most thoroughly investigated in microorganisms, where it has been found to affect membrane integrity and transport, cytoskeletal assembly and both DNA and protein synthesis. We will explore the diversity and activity of microorganisms from 2000 m to >8,000 m depths within the highly productive water column of hadal trenches, comparing seawater samples obtained with and without substantial pressure changes during recovery. A pressure retaining device was used to sample the microbial communities of the watercolumn with reduced decompression during retreival (Peoples et. al., 2019). References: Peoples LM, Norenberg M, Price D, McGoldrick M, Novotny M, Bochdansky A, Bartlett DH. A full-ocean-depth rated modular lander and pressure-retaining sampler capable of collecting hadal-endemic microbes under in situ conditions. Deep Sea Research Part I: Oceanographic Research Papers. 2019 Jan 1;143:50-7.

Plominsky, Alvaro M.↗
DOE OSTI2023

A section 110 evaluation of the 10,500-foot blast line civil effects structures and military trenches associated with the apple-2 test, area 1, nevada national security site, nye county, nevada

The U.S. Department of Energy, National Nuclear Security Administration Nevada Field Office (NNSA/NFO) has tasked Desert Research Institute (DRI) with identifying and evaluating additional resources that contribute to the significance of the Apple-2 Historic District as part of a Section 110 effort. Apple-2 was a 1955 atmospheric test in which the Federal Civil Defense Administration (FCDA) conducted an extensive civil effects program named Operation Cue. The objective of Operation Cue was to understand the blast and thermal effects of the test by using a simulated community of residential buildings, industrial structures, utilities, and commercial equipment arranged at various distances from ground zero (GZ). Military operations conducted by the Department of Defense (DoD) as part of the Desert Rock VI exercise were also associated with the Apple-2 test. The Apple-2 Historic District was originally defined in 2000 by Johnson and Edwards as 15 highly visible contributing elements dispersed across the landscape. Since its original recording, DRI has conducted additional archival research and this report details the identification and evaluation results of testing-related material remains at a distance of 10,500 ft from the Apple-2 GZ. Between 2017 and 2020, DRI conducted fieldwork at 10,500 ft from the Apple-2 GZ, revisited previously recorded contributing elements, and identified and evaluated newly recorded resources associated with Operation Cue as well as DoD operations. In total, DRI revisited or newly identified 15 principal resources. Of these, 13 are located within the historic district and contribute to the district’s significance. A set of military trenches and the associated material remains are discontiguous from the district, but also contribute to the district’s significance.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Evaluation of Hypotheses for the Fate of Historical Discharges from Hanford Site BC Cribs and Trenches

A preliminary review of declassified reports and historical documents from the 1950s and 1960s indicated they may contain valuable information regarding potential impacts to groundwater from liquid waste discharged to the 216-BC Cribs and Trenches during the late 1950s. Transport of contaminants in the vadose zone beneath the BC Cribs area is simulated by a vadose zone model developed for the Composite Analysis (DOE/RL-2019-52, Composite Analysis for Low-Level Waste Disposal in the Hanford Site Central Plateau ). Results from this model indicate there has been no substantial breakthrough of contaminants (particularly technetium-99) to groundwater from the vadose zone up to the present day. However, there is uncertainty in the anisotropy and other model input parameters as well as acknowledged sparseness of sampling data for this area. In this study, historical documents and other information were reviewed to evaluate the possibility that contaminant breakthrough to groundwater occurred during or shortly after operation of the BC Cribs sites, and whether refinements of the vadose zone model parametrization should be considered.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

A Comprehensive Stress Drop Map From Trench to Depth in the Northern Chilean Subduction Zone

We compute stress drops for earthquakes in Northern Chile recorded between 2007 and 2021. By applying two analysis techniques, (a) the spectral ratio (SR) method and (b) the spectral decomposition (SDC) method, a stress drop map for the subduction zone consisting of 51,510 stress drop values is produced. We build an extended set of empirical Green’s functions (EGF) for the SR method by systematic template matching. Outputs are used to compare with results from the SDC approach, where we apply cell-wise obtained global EGF's to compensate for the structural heterogeneity of the subduction zone. We find a good consistency of results of the two methods. The increased spatial coverage and quantity of stress drop estimates from the SDC method facilitate a consistent stress drop mapping of the different seismotectonic domains. Albeit only small differences of median stress drop, strike-perpendicular depth sections clearly reveal systematic variations, with earthquakes at different seismotectonic locations exhibiting distinct values. In particular, interface seismicity is characterized by the lowest observed median value, whereas upper plate earthquakes show noticeably higher stress drop values. Intermediate depth earthquakes show comparatively high average stress drop and a rather strong depth-dependent increase of median stress drop. Additionally, we observe spatio-temporal variability of stress drops related to the occurrence of the two megathrust earthquakes in the study region. The presented study is the first coherent large scale 3D stress drop mapping of the Northern Chilean subduction zone. It provides an important component for further detailed analysis of the physics of earthquake ruptures.

58 GEOSCIENCES↗
DOE OSTI2025

A Tale from the Trenches: Applying Metamorphic and Differential Testing to Bioinformatics Software

Metamorphic and differential testing have been proposed as best practices for testing software that is difficult to test, such as for programs in scientific domains. An assumption is that these approaches can be easily customized and applied to almost any domain. However, scientific software is often data-driven, and metamorphic relations may require significant domain knowledge to develop. In addition, tools are often written for ad-hoc experimentation by the scientists and often embed many assumptions about the importance and representation of different natural phenomena. In this paper, we present our experience applying both metamorphic and differential testing to a set of four computational biology tools that predict the growth of an organism. While our original goal was to evaluate these techniques to improve our system-level testing, we encountered multiple roadblocks along the way. Although we did find faults (some confirmed by developers), we also uncovered a set of challenges, including the considerable manual effort required for (a) defining domain-specific tests, (b) validating correctness, and (c) distinguishing between issues stemming from poor data and those arising from incorrect software.

Marsh, Alexis L [Iowa State University/Ames Labora↗