Search NASA⌕ Search

SEARCH · Search NASA

Results for “trimming”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

A closed-form trim solution yielding minimum trim drag for airplanes with multiple longitudinal-control effectors

Airplane designs are currently being proposed with a multitude of lifting and control devices. Because of the redundancy in ways to generate moments and forces, there are a variety of strategies for trimming each airplane. A linear optimum trim solution (LOTS) is derived using a Lagrange formulation. LOTS enables the rapid calculation of the longitudinal load distribution resulting in the minimum trim drag in level, steady-state flight for airplanes with a mixture of three or more aerodynamic surfaces and propulsive control effectors. Comparisons of the trim drags obtained using LOTS, a direct constrained optimization method, and several ad hoc methods are presented for vortex-lattice representations of a three-surface airplane and two-surface airplane with thrust vectoring. These comparisons show that LOTS accurately predicts the results obtained from the nonlinear optimization and that the optimum methods result in trim drag reductions of up to 80 percent compared to the ad hoc methods.

Goodrich, Kenneth H.↗
NASA NTRS1977

TRIM-STAB-Aerospace vehicle trim and stability

Program calculates stability and control characteristics of aerospace vehicles, which are usally calculated by either constant coefficient time-slice linear analysis or by nonlinear simulation.

Barnes, R. E.↗
NASA NTRS2010

Development and Operation of an Automatic Rotor Trim Control System for use During the UH-60 Individual Blade Control Wind Tunnel Test

A full-scale wind tunnel test to evaluate the effects of Individual Blade Control (IBC) on the performance, vibration, noise and loads of a UH-60A rotor was recently completed in the National Full-Scale Aerodynamics Complex (NFAC) 40- by 80-Foot Wind Tunnel [1]. A key component of this wind tunnel test was an automatic rotor trim control system that allowed the rotor trim state to be set more precisely, quickly and repeatably than was possible with the rotor operator setting the trim condition manually. The trim control system was also able to maintain the desired trim condition through changes in IBC actuation both in open- and closed-loop IBC modes, and through long-period transients in wind tunnel flow. This ability of the trim control system to automatically set and maintain a steady rotor trim enabled the effects of different IBC inputs to be compared at common trim conditions and to perform these tests quickly without requiring the rotor operator to re-trim the rotor. The trim control system described in this paper was developed specifically for use during the IBC wind tunnel test

Theodore, Colin R.↗
NASA NTRS2010

Development and Operation of an Automatic Rotor Trim Control System for the UH-60 Individual Blade Control Wind Tunnel Test

An automatic rotor trim control system was developed and successfully used during a wind tunnel test of a full-scale UH-60 rotor system with Individual Blade Control (IBC) actuators. The trim control system allowed rotor trim to be set more quickly, precisely and repeatably than in previous wind tunnel tests. This control system also allowed the rotor trim state to be maintained during transients and drift in wind tunnel flow, and through changes in IBC actuation. The ability to maintain a consistent rotor trim state was key to quickly and accurately evaluating the effect of IBC on rotor performance, vibration, noise and loads. This paper presents details of the design and implementation of the trim control system including the rotor system hardware, trim control requirements, and trim control hardware and software implementation. Results are presented showing the effect of IBC on rotor trim and dynamic response, a validation of the rotor dynamic simulation used to calculate the initial control gains and tuning of the control system, and the overall performance of the trim control system during the wind tunnel test.

Theodore, Colin R.↗
NASA NTRS1947

Correlation of the Trim Limits of Stability Obtained for a PB2Y-3 Flying Boat and a 1/8-Size Powered Dynamic Model

Tests of a PB2Y-3 flying boat were made at the U.S> Naval Air Station, Patuxent River, Md., to determine its hydrodynamic trim limits of stability. Corresponding tests were also made of a 1/8-size powered dynamic model of the same flying boat in Langley tank no. 1. During the tank tests, the full-size testing procedure was reproduced as closely as possible in order to obtain data for a direct correlation of the results. As a nominal gross load of 66,000 pounds, the lower trim limits of the full-size and model were in good agreement above a speed of 80 feet per second. As the speed decreased below 80 feet per second, the difference between the model trim limits and full-scale trim limits gradually became larger. The upper trim limit of the model with flaps deflected 0 deg was higher than that of the full-size, but the difference was small over the speed range compared. At flap deflections greater than 0 deg, it was not possible to trim either the model of the airplane to the upper limit with the center of gravity at 28 percent of the mean aerodynamic chord. The decrease in the lower trim limits with increase in flap deflection showed good agreement for the airplane and model. The lower trim limits obtained at different gross loads for the full-size airplane were reduced to approximately a single curve by plotting trim against the square root of C(sub delta (sub o)) divided by C(sub V).

Garrison, Charlie C.↗
NASA NTRS1991

Trim drag reduction concepts for horizontal takeoff single-stage-to-Orbit vehicles

The results of a study to investigate concepts for minimizing trim drag of horizontal takeoff single-stage-to-orbit (SSTO) vehicles are presented. A generic hypersonic airbreathing conical configuration was used as the subject aircraft. The investigation indicates that extreme forward migration of the aerodynamic center as the vehicle accelerates to orbital velocities causes severe aerodynamic instability and trim moments that must be counteracted. Adequate stability can be provided by active control of elevons and rudder, but use of elevons to produce trim moments results in excessive trim drag and fuel consumption. To alleviate this problem, two solution concepts are examined. Active control of the center of gravity (COG) location to track the aerodynamic center decreases trim moment requirements, reduces elevon deflections, and leads to significant fuel savings. Active control of the direction of the thrust vector produces required trim moments, reduces elevon deflections, and also results in significant fuel savings. It is concluded that the combination of active flight control to provide stabilization, (COG) position control to minimize trim moment requirements, and thrust vectoring to generate required trim moments has the potential to significantly reduce fuel consumption during ascent to orbit of horizontal takeoff SSTO vehicles.

Shaughnessy, John D.↗
NASA NTRS1982

Experimental trim drag values and flow-field measurements for a wide-body transport model with conventional and supercritical wings

The purpose of this study was to determine if advanced supercritical wings incur higher trim drag values at cruise conditions than current wide body technology wings. Relative trim drag increments were measured in an experimental wind tunnel investigation conducted in the Langley 8 Foot Transonic Pressure Tunnel. The tests utilized a high aspect ratio supercritical wing and a wide body aircraft wing, in conjunction with five different horizontal tail configurations, mounted on a representative wide body fuselage. The three low tail and two T-tail configurations were designed to measure the effects of horizontal tail size, location, and camber on the trim drag increments for the two wings. Longitudinal force and moment data were taken at a Mach number of 0.82 and design cruise lift coefficients for the wide body and supercritical wings of 0.45 and 0.55, respectively. The data indicate that the supercritical wing does not have significantly higher trim drag than the wide body wing. A reduction in tail size, combined with relaxed static stability, produced trim drag reductions for both wings. The cambered tails had higher trim drag increments than the symmetrical tails for both wings, and the T-tail configurations had lower trim drag increments than the low tail configurations.

Jacobs, P. F.↗
NASA NTRS1934

The effect of trim angle on the take-off performance

Data obtained at the N.A.C.A. tank from tests on the models of three flying-boat hulls - N.A.C.A. models 11-A, 16, and 22 - are used to demonstrate the effect of trim angle on water resistance. A specific example is taken, and data from Model 11-A are used to show that the trim angle giving the minimum water resistance will give minimum total air-plus-water resistance. Total-resistance curves for best trimmed angles and other angles are compared for the same example. The effect of wind on best trim angles and upon the take-off and run is shown by the working of an example. The possibility of using tank data on trim angles as aid in piloting is discussed, and an instrument for use in determining the trim angle of seaplanes is described. The importance of maintaining the best trim angle throughout the take-off is indicated.

Shoemaker, James M↗
NASA NTRS1959

An Experimental Investigation of a Triangular Wing of Aspect Ratio 2 and a Body Warped to be Trimmed at M = 2.24

A cambered and twisted triangular wing of aspect ratio 2 in combination with a cambered body was investigated experimentally to determine the effectiveness of the camber in reducing the drag due to lift at trim at supersonic speeds. Four arrangements were tested comprising all combinations of a symmetrical and a cambered wing with a symmetrical and a cambered body. The camber shape investigated was derived by linearized lifting surface theory for triangular wings with sonic leading edges and satisfied the requirement that the wing be trimmed at the design Mach number and lift coefficient. The experimental results for the cambered wing and cambered body showed that the drag coefficient at trim was always greater, at the same lift coefficient, than that for the untrimmed symmetrical wing and body. The trim lift coefficient was positive and decreased with increasing Mach number. At the design Mach number of 2.24, the trim lift coefficient was somewhat lower and the drag coefficient was higher than values predicted by linearized lifting surface theory for the wing alone. A comparison of the trim lift-drag ratio of the cambered wing and cambered body with values obtained by trimming the symmetrical wing and symmetrical body either with a canard or a trailing-edge flap showed that, at approximately the design Mach number the cambered configuration developed a somewhat higher value than the trailing-edge flap configuration but a lower value than the canard configuration.

Adams, Gaynor J.↗
NASA NTRS2018

Trim Flight Conditions for a Low-Boom Aircraft Design Under Uncertainty

The purpose of this paper is to investigate the noise generation of a low-boom aircraft design in flight trim conditions under uncertainty. The deflection of control surfaces to maintain a trimmed flight state has the potential to change the perceived loudness at the ground. Furthermore, the uncertainties associated with the control surface deflections can complicate the overall uncertainty quantification. Incorporation of the uncertainties in the prediction of perceived sound levels during the design phase can lead to improved robustness. In this paper, a brief review of low-boom flight trim research is presented. Realistic flight trim conditions requiring control surface deflection are integrated into the current research efforts for uncertainty quantification and vehicle design. In addition, a generalized set of procedures for the characterization of uncertainties in flight trim conditions are introduced. In a case study of the application of these procedures, a 5 decibel average difference in the perceived level of loudness was found between clean (no deflections) and trimmed configurations. Also, uncertainties attributable to control surface deflection were found to account for, on average, over 50% of the total near field uncertainty. Uncertainty discretization methods implemented were able to give more insight into the overall global variances.

Phillips, Ben D↗
NASA NTRS1975

Some comments on trim drag

A discussion of data of and methods for predicting trim drag is presented. Specifically the following subjects are discussed: (1) economic impact of trim drag; (2) the trim drag problem in propeller driven airplanes and the effect of propeller and nacelle location; (3) theoretical procedures for predicting trim drag; and (4) research needs in the area of trim drag.

Roskam, J.↗
NASA NTRS1978

Effect of camber on the trimmed lift capability of a close-coupled canard-wing configuration

A close-coupled canard-wing configuration was tested in the Langely high-speed 7 by 10 foot tunnel at a Mach number of 0.30 to determine the effect of changing wing camber on the trimmed lift capability. Trimmed lift coefficients of near 2.0 were attained; however, the data indicated that the highest buffet-free trimmed lift coefficient attainable was approximately 1.30. The buffet used in this investigation were qualitative in nature and gave no indication of buffet intensity. Thus, the trimmed lift coefficient of near 2.0 might be attainable if the buffet intensity was not too high. The data showed that there was approximately a 10 percent variation in drag coefficient, for different model configurations, at a given trimmed lift coefficient. Large increases in wing lift had only small effects on canard lift.

Gloss, B. B.↗
NASA NTRS1986

Piloted simulation study of the effects of an automated trim system on flight characteristics of a light twin-engine airplane with one engine inoperative

A simulation study was conducted to investigate the piloting problems associated with failure of an engine on a generic light twin-engine airplane. A primary piloting problem for a light twin-engine airplane after an engine failure is maintaining precise control of the airplane in the presence of large steady control forces. To address this problem, a simulated automatic trim system which drives the trim tabs as an open-loop function of propeller slipstream measurements was developed. The simulated automatic trim system was found to greatly increase the controllability in asymmetric powered flight without having to resort to complex control laws or an irreversible control system. However, the trim-tab control rates needed to produce the dramatic increase in controllability may require special design consideration for automatic trim system failures. Limited measurements obtained in full-scale flight tests confirmed the fundamental validity of the proposed control law.

Stewart, E. C.↗
NASA NTRS1987

Airplane automatic control force trimming device for asymmetric engine failures

The difference in dynamic pressure in the propeller slipstreams as measured by sensors is divided by the freestream dynamic pressure generating a quantity proportional to the differential thrust coefficient. This quantity is used to command an electric trim motor to change the position of trim tab thereby retrimming the airplane to the new asymmetric power condition. The change in position of the trim tab produced by the electric trim motor is summed with the pilot's input to produce the actual trim tab position.

Stewart, Eric C.↗
NASA NTRS1991

Trim angle measurements in free-flight facilities

The aerodynamic cofficients and trim angle for an aerobrake at Mach 9.2 and 11.8 were found using a combination of experiment and computation. Free-flight tests were performed at NASA Ames Research Center's Hypervelocity Free-Flight Aerodynamic Facility, and the forebody pressure distribution was calculated using a three-dimensional Navier-Stokes code with an effective specific heat ratio. Using the computed drag, lift, and moments to prescribe the number of terms in the aerodynamic coefficient expansions and to specify the values of the higher order terms, the experimental aerodynamic coefficients and trim angle were found using a six-degree-of-freedom, weighted, least-squares analysis. The experimental and computed aerodynamic coefficients and trim angles are in good agreement. The trim angle obtained from the free-flight tests, 14.7 deg, differs from the design trim angle, 17 deg, and from the Langley wind tunnel results, 12 deg in air and 17 deg in CF4. These differences are attributable to real-gas effects.

Yates, Leslie A.↗
NASA NTRS1991

Periodic trim solutions with HP-version finite elements in time

Finite Element in Time has been proven to be a powerful alternative solving strategy for the rotor craft trim problem. Additionally, Finite Element Method in Time has been developed in various versions like time-marching framework, Galerkin framework, Rayleigh-Ritz framework, and mixed formulation. Recently, this method was applied to the rotorcraft trim problem to obtain linearized solutions. The rotorcraft trim problem consists of trying to find a period solution for period-coefficient, differential equations subject to side constraints where certain force and momentum balance equations are forced to be equal to zero. There are free (or trim) parameters that are chosen to meet these side constraints. This project aims at expanding the application, in terms of the rotorcraft trim problem, from a linearized solution to nonlinear solution.

Source record↗
NASA NTRS1947

Investigation of the Trim Characteristics of a 1/20-Scale Model of the Fleetwings XBTK-1 Airplane over a Wide Range of Angles of Attack

Tests of a 1/20-scale model of the Fleetwings XBTK-1 airplane have been performed in the Langley 15-foot free-spinning tunnel to determine the trim tendencies of the airplane at attitudes above the stall. The results of the tests indicated that the model would trim longitudinally only in the normal range of angles of attack and that the yaw trim tendencies for such longitudinal trim conditions were normal. Although wide oscillations in yaw were noted for some conditions, they occurred at angles of attack larger than those indicated as possible for longitudinal trim and spin equilibrium. It appears, therefore, that the oscillatory motions reported for the airplane may have been the direct result of control movements rather than the result of inherent oscillatory tendencies.

Stone, Ralph W., Jr.↗
NASA NTRS2013

Supersonic Aerodynamic Characteristics of Blunt Body Trim Tab Configurations

Trim tabs are aerodynamic control surfaces that can allow an entry vehicle to meet aerodynamic performance requirements while reducing or eliminating the use of ballast mass and providing a capability to modulate the lift-to-drag ratio during entry. Force and moment data were obtained on 38 unique, blunt body trim tab configurations in the NASA Langley Research Center Unitary Plan Wind Tunnel. The data were used to parametrically assess the supersonic aerodynamic performance of trim tabs and to understand the influence of tab area, cant angle, and aspect ratio. Across the range of conditions tested (Mach numbers of 2.5, 3.5, and 4.5; angles of attack from -4deg to +20deg; angles of sideslip from 0deg to +8deg), the effects of varying tab area and tab cant angle were found to be much more significant than effects from varying tab aspect ratio. Aerodynamic characteristics exhibited variation with Mach number and forebody geometry over the range of conditions tested. Overall, the results demonstrate that trim tabs are a viable approach to satisfy aerodynamic performance requirements of blunt body entry vehicles with minimal ballast mass. For a 70deg sphere-cone, a tab with 3% area of the forebody and canted approximately 35deg with no ballast mass was found to give the same trim aerodynamics as a baseline model with ballast mass that was 5% of the total entry mass.

Korzun, Ashley M.↗