Search NASA⌕ Search

SEARCH · Search NASA

Results for “tungsten target”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Secondary Pion Production using the LINAC Beam on Graphite and Tungsten Targets

The Fermilab 400-MeV Linac primary proton beam can produce precision, single-species secondary beams using a production target in the MeV Test Area experimental hall; specifically, pions from 4 up to 120 MeV kinetic energy. (These low energy pions rapidly decay into a muon beam in a secondary collection and transport beamline.) Although graphite is a standard production target material given its ultra-high temperature tolerance and low impact on the post-target primary beam, secondary pion/muon total production cross sections increase approximately as Z1/3 for positive muons and N2/3 for negative muons. Higher mass targets such as tungsten can potentially increase low-energy m+ and m- rates by factors of 3 and 8, respectively. Initial production studies have confirmed higher muon yield from heavy targets (tungsten vs carbon), but also, surprisingly, show significant differences in pion production between modern hadronic models (GENIEhad) and between GEANT and MCNP, state of the art production modeling codes. This project will further investigate the production discrepancies between these two target materials and between different physics models with high-statistics runs using the GEANT-based code, G4Beamline to better quantify the results and compare with production data which will be obtained using the MTA secondary beamline.

Ahmed, Shiza↗

High purity tungsten targets

High purity tungsten, which is used for targets in X-ray tubes was considered for space processing. The demand for X-ray tubes was calculated using the growth rates for dental and medical X-ray machines. It is concluded that the cost benefits are uncertain.

Source record↗

Proton beam power limits for stationary water-cooled tungsten target with different cladding materials

The proton beam power limit for a solid-tungsten spallation target is largely determined by beam induced thermomechanical structural loads and decay heat power deposition, while its lifetime is limited by radiation damage and fatigue life of the target materials. In this paper, we studied the power limits of a stationary water-cooled solid tungsten target concept. Tantalum clad tungsten was considered as a reference case. Being a low activation material, zircaloy 2 cladding option was studied and its decay heat driven power limit was compared with the reference case. Zirconium alloys have proven operations records in spallation target and nuclear fission environments, supported by materials data obtained from post irradiation examinations. Recent study also demonstrated feasibility of diffusion bonding zirconium to tungsten using vanadium foil inter layer. Particle transport simulations code FLUKA was used to calculate energy deposition and decay heat power deposition in the target, based on the beam parameters technically feasible at the Second Target Station of the Spallation Neutron Source at Oak Ridge National Laboratory. The energy deposition data were used for flow, thermal, and structural analyses to determine the beam intensity limit on the target concept studied. The decay heat deposition data were used to calculate the transient temperature evolution in the tungsten volumes in a loss of coolant accident (LOCA) scenario to determine its beam power limit. For a 1.3 GeV proton beam, the power limit on a stationary target was 400 kW for a tantalum clad target model and 800 kW for a zircaloy 2 clad target model.

Lee, Yong Joong↗

Uncertainty Quantification of Monolithic Tungsten Target Block Fatigue

The current STS spallation target design consists of 21 water cooled, tantalum clad, monolithic tungsten blocks. The target wheel assembly rotates such that each target block receives a direct proton pulse every 1.4 seconds (21 blocks / 15 Hz pulses). The quasi-steady heating induced by the repetitive beam pulses creates a significant mean stress distribution in the target. On top of this, the rapid energy deposition from a proton pulse induces dynamic stress waves that are of the same order of magnitude as the mean stresses. Over the design goal of 5,000 operational hours per year for a decade, each target must withstand over 130 million repetitions of these dynamic stress events. The fatigue life prediction of the target blocks is a complex sequence of simulations that depend upon a set of input parameters. For the tungsten block, the end goal is the fatigue factor-of-safety (FOS). This study documents a new structural analysis routine using software available to U.S. national laboratories (e.g. CUBIT, Sierra Multiphysics, Dakota) that enables more rapid target fatigue analysis. The increased throughput is amenable to parameter sensitivity and uncertainty quantification (UQ) studies. A set of input parameters (ultimate strength, fatigue strength, density, elastic modulus, Poisson’s ratio, thermal conductivity, coefficient of thermal expansion, specific heat, flow rate) with expected ranges are documented based on literature data, recent experimental testing, and engineering judgement. UQ bounds the resulting fatigue FOS at [0.5, 3.4] using epistemic interval analysis. These bounds are expected to be wider due to model effects (discretization) and beam effects (focus, offset) that were not included. Parameter sensitivity underscores the importance of ultimate strength and fatigue strength of irradiated tungsten on the fatigue calculations.

43 PARTICLE ACCELERATORS↗

MTA Secondary Beamline Production and Optics Optimization

A new secondary beamline was recently installed in the MeV Test Area (MTA) with the objective of enhancing mu+/mu- production by factors of 3/8 by using a tungsten target versus the conventional graphite production target using the 400 MeV Fermilab proton Linac beam. Ultra-low energy muon beams can support world-class physics experiments for fundamental muon measurements, sensitive searches for symmetry violation, and precision tests of theory. Extensive production studies have confirmed higher muon yield from heavy targets (tungsten vs carbon), but also, surprisingly, showed significant differences in production fluence and energy spectrum between modern hadronic models (GENIEhad) and between GEANT and MCNP. Studies are also underway towards a high-efficiency source of muonium by stopping the mu+ beam in superfluid helium. Muon fluxes can be measured at MTA including using higher-Z and novel target geometries to test hadronic and production models which are critical to understanding ongoing experiments (Mu2e) and will significantly impact the planning of future HEP experiments and planning PIP II facilities. The MTA beamline will additionally support a broad user muon test beam for future experiments and R&D.

Ahmed, Shiza↗

First Observation Of New Neutron-Rich Magnesium, Aluminum, and Silicon Isotopes

The investigation of the limits of nuclear existence is fundamental to the understanding of nuclear forces and structure. The limits of binding for very neutron-rich nuclei and the location of the neutron dripline are established experimentally only for the lightest elements. We report on the discovery of the new neutron-rich isotopes {sup 40}Mg, {sup 42,43}Al, and {sup 44}Si. These rare isotopes were produced at the National Superconducting Cyclotron Laboratory by fragmentation of a 141 MeV/u {sup 48}Ca beam on a tungsten target. The combination of the A1900 fragment separator together with the analysis beam line of the S800 spectrograph provided a two-stage fragment separation with exceptional selectivity. The observation of the odd-odd nucleus {sup 42}Al, which was predicted to be unbound by FRDM [1] and HFB-8 [2] models, is the first indication that the neutron drip line may be located significantly further towards heavier isotopes in this mass region than it is currently believed.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

An investigation of the normal momentum transfer for gases on tungsten

The near monoenergetic beam of neutral helium and argon atoms impinged on a single crystal tungsten target, with the (100) face exposed to the beam. The target was mounted on a torsion balance. The rotation of this torsion balance was monitored by an optical lever, and this reading was converted to a measurement of the momentum exchange between the beam and the target. The tungsten target was flashed to a temperature in excess of 2000 C before every clean run, and the vacuum levels in the final chamber were typically between 0.5 and 1 ntorr. The momentum exchange for the helium-tungsten surface and the argon-tungsten surface combination was obtained over approximately a decade of incoming energy (for the argon gas) at angles of incidence of 0, 30, and 41 deg on both clean and dirty (gas covered) surfaces. The results exhibited a significant variation in momentum transfer between the data obtained for the clean and dirty surfaces. The values of normal momentum accommodation coefficient for the clean surface were found to be lower than the values previously reported.

Moskal, E. J.↗

Diffusion bonding of tungsten-vanadium-zirconium using vacuum hot pressing for the development of a low decay heat cladding solution for tungsten spallation targets

Tantalum has been used as cladding material for water-cooled solid tungsten targets at many leading spallation neutron production facilities thanks to its high neutron yield, manageable radiation damage behavior, and excellent corrosion/erosion resistance in radiation environments. However, from a safety hazard perspective, thermal neutron capture of tantalum in spallation environments causes a high specific decay heat in the target volume, which often becomes a limiting factor in increasing the beam power on the target. In this paper, we studied vacuum hot pressing (VHP) parameters to diffusion bond zirconium to tungsten to explore the feasibility of using zirconium alloys as an alternative cladding material to tantalum. Zirconium alloys have long been used as cladding material for early generation solid spallation targets, and nuclear fuel rods. In spallation environments zirconium has significantly lower decay heat with shorter decay time compared to tantalum. The hot isostatic pressing (HIP) of zirconium and tungsten is known to produce limited bonding quality due to the formation of the brittle ZrW2 intermetallic layer. To overcome this problem, placing a vanadium interlayer between tungsten and zirconium has been proposed by exploring parameter space in binary alloy phase diagrams. Under the VHP conditions, 860 ◦C at 70 MPa for 4 hours, Zr-V and V-W showed good diffusion bonding, which demonstrates the feasibility of a single step HIP process to make the zirconium alloy clad tungsten spallation volumes.

Lee, Yong Joong↗

Temperature of a tungsten spallation target

We discuss the heat load inside a neutron spallation target made of tungsten hit by an 800 MeV proton beam. This problem is important for the Neutron Target project, where a spallation target will be surrounded by an extended graphite or beryllium cube to create a neutron target. The idea of a free-neutron target enables the measurement of neutron-induced reactions in inverse kinematics. This idea is part of the LANSCE strategy to stay a worldwide leader for neutron-induced research.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Results of high heat flux tests of tungsten divertor targets under plasma heat loads expected in ITER and tokamaks (review)

Heat loads on the tungsten divertor targets in the ITER and the tokamak power reactors reach ~10MW m{sup −2} in the steady state of DT discharges, increasing to ~0.6–3.5 GW m{sup −2} under disruptions and ELMs. The results of high heat flux tests (HHFTs) of tungsten under such transient plasma heat loads are reviewed in the paper. The main attention is paid to description of the surface microstructure, recrystallization, and the morphology of the cracks on the target. Effects of melting, cracking of tungsten, drop erosion of the surface, and formation of corrugated and porous layers are observed. Production of submicron-sized tungsten dust and the effects of the inhomogeneous surface of tungsten on the plasma–wall interaction are discussed. In conclusion, the necessity of further HHFTs and investigations of the durability of tungsten under high pulsed plasma loads on the ITER divertor plates, including disruptions and ELMs, is stressed.

36 MATERIALS SCIENCE↗

The Investigation of the Rare Metal Content in the Geological Samples from Mongolia on the Iren Facility

Definition of the content of rare metals in the samples of ore was carried out by the method of the neutron activation analysis. IREN installation which represents the linear electron accelerator and no multiplying tungsten target served as the neutron source. The tungsten target has been located in the centre of the water moderator in diameter 15 cm.The irradiation has been spent on installation IREN within 8 hours 40 minutes. Electron energy was an order of 30 MeV, a current of an order 5 -10 microamperes. Samples settled down on the moderator surface. 2 samples of ore have been irradiated: Os-1 (m = 1.172 g), and Os-2 (m = 1.291 g) and a number of indicators for definition of neutron flux. Weights of indicators did not exceed a several milligrams.

07 ISOTOPE AND RADIATION SOURCES↗

Optimization of radiography applications using x-ray beams emitted by compact accelerators. Part I. Monte Carlo study of the hard x-ray spectrum

Purpose: A 3-year project called LABSYNC has been recently funded by the European Commission, with the aim of designing a radiation facility based on a compact light source, i.e., a laboratory-sized commercial synchrotron, capable of accelerating electrons up to 6 or 20 MeV. An accurate spectral description of hard x rays emitted from thin targets, irradiated by electron beams circulating in the storage ring, is of primary interest for the design and the characterization of a beamline. This article, Part I, aims at optimizing some of the parameters which are critical for the design of medical applications based on the above compact light source. The goal was to evaluate the dependence of photon fluence and beam monochromaticity on electron-beam energy, target material, and thickness. Methods: The transport of 6 and 20 MeV electrons in a thin molybdenum, rhodium, and tungsten target is studied by means of Monte Carlo simulations using MCNPX. Configurations of the x-ray output port, different from the default forward-directed emission of the beam, are also investigated. A comparison with reference spectra for general diagnostic radiology and mammography is carried out. Results: It is shown that the emitted x-ray beams can be far more intense than those generated by conventional x-ray tubes for radiography applications. The profiles of the calculated polychromatic spectra resemble those generated by conventional x-ray tubes, with x-ray energies up to the energy of the incident-electron beam. An appreciable improvement in the monochromaticity of the beams can be obtained by viewing the x-ray emission from an output port antiparallel to the direction of the incident-electron beam. Conclusions: The optimum target thickness for tungsten target spectra is practically constrained by a trade-off between bremsstrahlung efficiency and focal-spot size requirements. A larger margin for optimization of target thickness is probably available for mammographic spectra. The constraint of a backward-directed (or, to a lesser extent, orthogonal) output port is to be considered mandatory for minimizing the high-energy tail of the spectral distribution and keeping the radiation dose to a reasonable level. It is also fundamental to evaluate the impact of the high-energy tail of the emitted spectra in x-ray imaging applications, since the energy range involved is significantly beyond the diagnostic range. This topic will be dealt with in Part II of the article.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Plant model of KIPT neutron source facility simulator

Argonne National Laboratory (ANL) of the United States and Kharkov Institute of Physics and Technology (KIPT) of Ukraine are collaborating on constructing a neutron source facility at KIPT, Kharkov, Ukraine. The facility has 100-kW electron beam driving a subcritical assembly (SCA). The electron beam interacts with a natural uranium target or a tungsten target to generate neutrons, and deposits its power in the target zone. The total fission power generated in SCA is about 300 kW. Two primary cooling loops are designed to remove 100-kW and 300-kW from the target zone and the SCA, respectively. A secondary cooling system is coupled with the primary cooling system to dispose of the generated heat outside the facility buildings to the atmosphere. In addition, the electron accelerator has a low efficiency for generating the electron beam, which uses another secondary cooling loop to remove the generated heat from the accelerator primary cooling loop. One of the main functions the KIPT neutron source facility is to train young nuclear specialists; therefore, ANL has developed the KIPT Neutron Source Facility Simulator for this function. In this simulator, a Plant Control System and a Plant Protection System were developed to perform proper control and to provide automatic protection against unsafe and improper operation of the facility during the steady-state and the transient states using a facility plant model. This report focuses on describing the physics of the plant model and provides several test cases to demonstrate its capabilities. The plant facility model uses the PYTHON script language. It is consistent with the computer language of the plant control system. It is easy to integrate with the simulator without an additional interface, and it is able to simulate the transients of the cooling systems with system control variables changing on real-time.

43 PARTICLE ACCELERATORS↗

Liquid metal-based polarized positron generation benchmark using the GEANT4 toolkit

In this work, we report simulation results for the positron yield and polarization of polarized electron beams incident on GaInSn and PbBi liquid metal targets. One of the proposed upgrades to 12 GeV CEBAF is the use of a continuous wave polarized positron beam for physics experiments. High-Z liquid metal jets are excellent candidates for positron production targets because they can withstand high power beams. Polarized positron beams can be generated from a primary electron beam incident to thick high-Z targets through circular polarized bremsstrahlung conversion to linearly polarized pair production. This polarization transfer from the primary electron beam has been previously demonstrated at Jefferson Lab in the PEPPo experiment with a tungsten target at relatively low energies. Here we report Geant4 simulations for 10 and 120 MeV electron beams incident on GaInSn and PbBi liquid metal targets. These simulations are compared to simulations with a solid tungsten target, as well as with unpolarized simulations using MCNP6.

Lizarraga-Rubio, Victor Manuel↗

Study of central production of charged pionic modes at COMPASS

The COmmon Muon and Proton Apparatus for Structure and Spectroscopy is a fixed target experiment at the CERN SPS accelerator. In the years 2008 and 2009 the collaboration focused on hadron spectroscopy: data with hadronic beams at a momentum of 190 GeV/c impinging on hydrogen, lead, nickel and tungsten targets were taken. In the preparation for this run-time, the apparatus was adapted to measure the formation of resonances by both diffractive scattering and central production. In the latter case, the study of charged pionic channels is well-suited to search for members of the f{sub 0} particle family, including some of the glueball candidates. The analysis of the newly taken data has started, these proceedings are meant to give a status and overview of the current activities.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗