Search NASA⌕ Search

SEARCH · Search NASA

Results for “turbulent length scale”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Investigation of the effect of inlet turbulence length scale on fan discrete tone noise

Results of an experimental investigation at the Ames 40- by 80-Foot Wind Tunnel of fan rotor alone discrete tone noise is presented. The investigation examines rotor interaction with fan inlet turbulence. The importance of turbulence length scale is shown by comparing the fan radiated acoustic spectrum with and without modified turbulence length scales. A small-scale low pressure ratio fan was used for the experiment.

Hodder, B. K.↗
NASA NTRS2014

Procedure for Determining Turbulence Length Scales Using Hotwire Anemometry

Hotwire anemometers are used to measure instantaneous velocity from which the mean velocity and the velocity fluctuation can be determined. Using a hotwire system, it is possible to deduce not only the velocity components and their fluctuation but to also analyze the energy spectra and from that the turbulence length scales. In this experiment, hotwire anemometry is used to measure the flow field turbulence for an array of film cooling holes. The objective of this paper is to document the procedure that is used to reduce the instantaneous velocity measurements to determine the turbulence length scales using data from the film-cooling experiments to illustrate the procedure.

turbulence measurements↗
NASA NTRS1987

Atmospheric lateral and longitudinal turbulent length scales (measured at 600 to 800 meters above grade level)

NASA's Airborne Doppler Lidar System has been used to obtain a detailed 'instantaneous' mapping of horizontal spatial wind fields at 600-800 m elevations on the east side of the San Gorgonio Pass in California, in the form of checkerboard-fashion horizontal wind vectors spaced at 300 m intervals along and normal to the flight path. Spatial autocorrelations for the lateral and longitudinal components are ensemble-averaged, and integral turbulent length scales are computed for the wind fields' longitudinal and lateral directions. The flow in the region studied does not appear to be isotropic.

Cliff, W. C.↗
NASA NTRS2014

Inlet Turbulence and Length Scale Measurements in a Large Scale Transonic Turbine Cascade

Constant temperature hotwire anemometry data were acquired to determine the inlet turbulence conditions of a transonic turbine blade linear cascade. Flow conditions and angles were investigated that corresponded to the take-off and cruise conditions of the Variable Speed Power Turbine (VSPT) project and to an Energy Efficient Engine (EEE) scaled rotor blade tip section. Mean and turbulent flowfield measurements including intensity, length scale, turbulence decay, and power spectra were determined for high and low turbulence intensity flows at various Reynolds numbers and spanwise locations. The experimental data will be useful for establishing the inlet boundary conditions needed to validate turbulence models in CFD codes.

hotwire↗
NASA NTRS1989

Cross correlation and length scales in turbulent flows near surfaces

Two kinds of length scales are used in turbulent flows; 'functional length scales' such as mixing length, dissipation length L(sub epsilon), etc., and 'flow-field length scales' derived from cross correlations of velocity, pressure, etc. in the flow. Some connection between these scales are derived here. We first consider the cross correlation R(sub vv)(y,y(sub 1)) of the normal components u at two heights y, y(sub 1) above a rigid surface, normalized by the velocity y(sub 1) (greater than y). For shear-free boundary layers it is found theoretically, and in field and numerical experiments that R(sub vv) approximately equals y/y(sub 1). For shear layers it is also found that R(sub vv) approximately equals f(y/y(sub 1)) less than or equal to y,y(sub 1). This function f differs slightly between low Reynolds number numerical simulations and field experiments. The lateral structure defined by R(sub vv)(y,r(sub 3); y(sub 1),0) is also self similar and shows that the eddies centered at about y(sub 1) appear to have constant lateral width a(sub 3) above and below y(sub 1), where a(sub 3, sup +) approximately equals 7+1/(1.4dU(sup +)/dy(sup +)), when normalized on u(sub *) and v, where U is the mean velocity. Results for L(sub epsilon, sup -1) from direct numerical simulation are found to compare well with the formula L(sub epsilon, sup -1) = A(sub B)/y + A(sub S)dU/dy/v, for unidirectional and reversing turbulent boundary layers and channel flow, except near where dU/dy approximately equals 0. The conclusion is that the large-scale eddy structure and length scales in these flows are determined by a combination of shear and blocking, and that the vertical component of turbulence has a self-similar structure in both kinds of boundary layer.

Hunt, J. C. R.↗
NASA NTRS1987

A general form for the dissipation length scale in turbulent shear flows

It has been found that, for a wide range of turbulent wall-bounded shear flows with mean velocity profile U(y), the scale length L-epsilon determining the dissipation is approximately described in terms of distance from the wall (y), the mean shear (dU/dy), and the variance of the normal component of turbulence (bar u-squared), by the formula: L-epsilon to the -1 power is approximately equal to (A sub B / y) + A sub S (dU/dy / square root of bar u-squared) where L-epsilon = epsilon/(bar u-squared) to the 3/2 power. To match with shear-free boundary layers, A sub B is approximately 0.27, and to match with the log layer, A sub S is approximately 0.46. The shear flows tested here were: boundary layers over a flat plate, sink flow, oscillatory flow, and channel flow. The use of the square root of bar u-squared as a velocity scale minimizes the effects of Reynolds number. However, the formula fails within a distance of order L-epsilon for the regions where dU/dy = 0.

Hunt, J. C. R.↗
NASA NTRS1976

Some factors influencing radiation of sound from flow interaction with edges of finite surfaces

Edges of surfaces which are exposed to unsteady flow cause both strictly acoustic effects and hydrodynamic effects, in the form of generation of new hydrodynamic sources in the immediate vicinity of the edge. An analytical model is presented which develops the explicit sound-generation role of the velocity and Mach number of the eddy convection past the edge, and the importance of relative scale lengths of the turbulence, as well as the relative intensity of pressure fluctuations. The Mach number (velocity) effects show that the important paramater is the convection Mach number of the eddies. The effects of turbulence scale lengths, isotropy, and spatial density (separation) are shown to be important in determining the level and spectrum of edge sound radiated for the edge dipole mechanism. Experimental data is presented which provides support for the dipole edge noise model in terms of Mach number (velocity) scaling, parametric dependence on flow field parameter, directivity, and edge diffraction effects.

Hayden, R. E.↗
NASA NTRS2005

Numerical Study of High-Temperature Jet Flow Using RANS/LES and PANS Formulations

Two multi-scale-type turbulence models are implemented in the PAB3D solver. The models are based on modifying the Reynolds Averaged Navier-Stokes (RANS) equations. The first scheme is a hybrid RANS/LES model utilizing the two-equation (k(epsilon)) model with a RANS/LES transition function dependent on grid spacing and the computed turbulence length scale. The second scheme is a modified version of the Partially Averaged Navier-Stokes (PANS) model, where the unresolved kinetic energy parameter (f(sub k)) is allowed to vary as a function of grid spacing and the turbulence length scale. This parameter is estimated based on a novel two-stage procedure to efficiently estimate the level of scale resolution possible for a given flow on a given grid for Partial Averaged Navier-Stokes (PANS). It has been found that the prescribed scale resolution can play a major role in obtaining accurate flow solutions. The parameter f(sub k) varies between zero and one and equal to one in the viscous sub layer, and when the RANS turbulent viscosity becomes smaller than the LES viscosity. The formulation, usage methodology, and validation examples are presented to demonstrate the enhancement of PAB3D's time-accurate and turbulence modeling capabilities. The accurate simulations of flow and turbulent quantities will provide valuable tool for accurate jet noise predictions. Solutions from these models are compared to RANS results and experimental data for high-temperature jet flows. The current results show promise for the capability of hybrid RANS/LES and PANS in simulating such flow phenomena.

Abdol-Hamid, Khaled S.↗
NASA NTRS2008

Calculations of High-Temperature Jet Flow Using Hybrid Reynolds-Average Navier-Stokes Formulations

Two multiscale-type turbulence models are implemented in the PAB3D solver. The models are based on modifying the Reynolds-averaged Navier Stokes equations. The first scheme is a hybrid Reynolds-averaged- Navier Stokes/large-eddy-simulation model using the two-equation k(epsilon) model with a Reynolds-averaged-Navier Stokes/large-eddy-simulation transition function dependent on grid spacing and the computed turbulence length scale. The second scheme is a modified version of the partially averaged Navier Stokes model in which the unresolved kinetic energy parameter f(sub k) is allowed to vary as a function of grid spacing and the turbulence length scale. This parameter is estimated based on a novel two-stage procedure to efficiently estimate the level of scale resolution possible for a given flow on a given grid for partially averaged Navier Stokes. It has been found that the prescribed scale resolution can play a major role in obtaining accurate flow solutions. The parameter f(sub k) varies between zero and one and is equal to one in the viscous sublayer and when the Reynolds-averaged Navier Stokes turbulent viscosity becomes smaller than the large-eddy-simulation viscosity. The formulation, usage methodology, and validation examples are presented to demonstrate the enhancement of PAB3D's time-accurate turbulence modeling capabilities. The accurate simulations of flow and turbulent quantities will provide a valuable tool for accurate jet noise predictions. Solutions from these models are compared with Reynolds-averaged Navier Stokes results and experimental data for high-temperature jet flows. The current results show promise for the capability of hybrid Reynolds-averaged Navier Stokes and large eddy simulation and partially averaged Navier Stokes in simulating such flow phenomena.

Abdol-Hamid, Khaled S.↗
NASA NTRS2004

Numerical Study of Flow Past a Circular Cylinder Using RANS, Hybrid RANS/LES and PANS Formulations

Two multiscale type turbulence models are implemented in the PAB3D solver. The models are based on modifying the Reynolds Averaged Navier-Stokes (RANS) equations. The first scheme is a hybrid RANS/LES model utilizing the two-equation (k(sub epsilon)) model with a RANS/LES transition function dependent on grid spacing and the computed turbulence length scale. The second scheme is a modified version of the partially averaged Navier-Stokes (PANS) model, where the unresolved kinetic energy parameter (f(sub k)) is allowed to vary as a function of grid spacing and the turbulence length scale. Solutions from these models are compared to RANS results and experimental data for a stationary and rotating cylinder. The parameter f(sub k) varies between zero and one and has the characteristic to be equal to one in the viscous sub layer, and when the RANS turbulent viscosity becomes smaller than the LES viscosity. The formulation, usage methodology, and validation example are presented to demonstrate the enhancement of PAB3D's time-accurate and turbulence modeling capabilities. The models are compared to RANS results and experimental data for turbulent separated flows (TS) and laminar separated flows (LS) around stationary and rotating cylinders. For a stationary cylinder, the TS case is accurately simulated using the general two-equation k(sub epsilon) turbulence model (eddy-viscosity model). PAB3D accurately predicts the drag coefficient (CD), lift coefficient (CL) and the Strouhal number (St). The LS case was a challenge for the RANS computation with an eddy-viscosity turbulence model. The RANS/LES and PANS performed well and showed marked improvements over the RANS solution. The modified PANS model was the most accurate. For the rotating cylinder, the spin ratio varied from zero to one, and the PANS results were in good agreement with published experimental data. RANS/LES and PANS capture both temporal and spatial fluctuations and produce large-scale structures that do not occur in the RANS simulation. The current results show promise for the capability of PANS in simulating unsteady and complex flow phenomena.

Elmiligui, Alaa A.↗
NASA NTRS1977

Neutrally stable atmospheric flow over a two-dimensional rectangular block

The phenomena of atmospheric flow over a two dimensional surface obstruction such as a building modeled as a rectangular block are analyzed by an approach using the Navier-Stokes equations with a two equation model of turbulence. The partial differential equations for the vorticity, stream function, turbulence kinetic energy, and turbulence length scale are solved by a finite difference technique. The predicted results are in agreement with the limited experimental data available. Current computed results show that the separation bubble originates from the upper front corner of the block and extends approximately 11.5 block heights behind the block. The decay of the mean velocity along the wake center line coincides almost perfectly with the experimental data. The vertical profiles of the mean velocity defect are also in reasonable agreement with wind tunnel results. Velocity profiles in the mixing region are shown to agree with the error function profile typically found in the shear layer. Details of the behavior of the turbulence kinetic energy and the turbulence length scale are also discussed.

Shieh, C. F.↗
NASA NTRS1975

Modelling atmospheric turbulence for a motion-based simulator

The background information in establishing several proposed atmospheric turbulence models for use on motion based aircraft simulators was documented. A specific model was proposed which, in addition to varying turbulence intensity (rms velocity), varies the atmospheric turbulence scale length to achieve compatibility with real atmospheric turbulence. With a suitable combination of scale length and intensity distribution, the model will simulate various atmospheric conditions characterized by altitude, stability, and terrain. The model is mechanized to be included in a flight simulator experiment in order to determine to what extent the pilots are sensitive to changes in atmospheric conditions and the realism of the model. The following topics were covered: literature survey, presently used techniques, proposed model, and simulation details.

Jacobson, I. D.↗
NASA NTRS1989

A numerical study of a class of TVD schemes for compressible mixing layers

At high Mach numbers the two-dimensional time-developing mixing layer develops shock waves, positioned around large-scale vortical structures. A suitable numerical method has to be able to capture the inherent instability of the flow, leading to the roll-up of vortices, and also must be able to capture shock waves when they develop. Standard schemes for low speed turbulent flows, for example spectral methods, rely on resolution of all flow-features and cannot handle shock waves, which become too thin at any realistic Reynolds number. The performance of a class of second-order explicit total variation diminishing (TVD) schemes on a compressible mixing layer problem was studied. The basic idea is to capture the physics of the flow correctly, by resolving down to the smallest turbulent length scales, without resorting to turbulence or sub-grid scale modeling, and at the same time capture shock waves without spurious oscillations. The present study indicates that TVD schemes can capture the shocks accurately when they form, but (without resorting to a finer grid) have poor accuracy in computing the vortex growth. The solution accuracy depends on the choice of limiter. However a larger number of grid points are in general required to resolve the correct vortex growth. The low accuracy in computing time-dependent problems containing shock waves as well as vortical structures is partly due to the inherent shock-capturing property of all TVD schemes. In order to capture shock waves without spurious oscillations these schemes reduce to first-order near extrema and indirectly produce clipping phenomena, leading to inaccuracy in the computation of vortex growth. Accurate simulation of unsteady turbulent fluid flows with shock waves will require further development of efficient, uniformly higher than second-order accurate, shock-capturing methods.

Sandham, N. D.↗
NASA NTRS2015

Verification and Validation of the k-kL Turbulence Model in FUN3D and CFL3D Codes

The implementation of the k-kL turbulence model using multiple computational uid dy- namics (CFD) codes is reported herein. The k-kL model is a two-equation turbulence model based on Abdol-Hamid's closure and Menter's modi cation to Rotta's two-equation model. Rotta shows that a reliable transport equation can be formed from the turbulent length scale L, and the turbulent kinetic energy k. Rotta's equation is well suited for term-by-term mod- eling and displays useful features compared to other two-equation models. An important di erence is that this formulation leads to the inclusion of higher-order velocity derivatives in the source terms of the scale equations. This can enhance the ability of the Reynolds- averaged Navier-Stokes (RANS) solvers to simulate unsteady ows. The present report documents the formulation of the model as implemented in the CFD codes Fun3D and CFL3D. Methodology, veri cation and validation examples are shown. Attached and sepa- rated ow cases are documented and compared with experimental data. The results show generally very good comparisons with canonical and experimental data, as well as matching results code-to-code. The results from this formulation are similar or better than results using the SST turbulence model.

Abdol-Hamid, Khaled S.↗
NASA NTRS2018

Development and Documentation of kL-Based Linear, Nonlinear, and Full Reynolds Stress Turbulence Models

The development and implementation of kL-based Reynolds Average Navier-Stokes (RANS) turbulence models are reported herein. The kL is based on Abdol-Hamid's closure and Menter's modi cation to Rotta's two-equation model. Rotta shows that a reliable transport equation can be formed from the turbulent length scale L, and the turbulent kinetic energy k. Rotta's kL equation is well suited for term-by-term modeling and displays useful features compared to other scale formulation. One of the important di erences is the inclusion of higher order velocity derivatives in the source terms of the scale equation. This can enhance the ability of RANS solvers to simulate unsteady ows in URANS mode. The present report documents the formulation of three model levels of turbulence models as implemented in the CFD code FUN3D. Methodology and calibration examples are shown in detail. The levels are the linear k-kL and the two-equation algebraic Reynolds stress model (ARSM) as well as the full Reynolds Stress Model (RSM). Attached, separated and corner ow cases are documented and compared with experimental, theoretical and other turbulence model data. The results show generally very good comparisons with canonical and experimental data. The results from this formulation are similar or better than results using the SST two- equation turbulence model. ARSM shows great promise with similar level of computational resources as general two equation turbulence models.

Abdol-Hamid, Khaled S.↗
NASA NTRS2018

kL-based Linear and Nonlinear Two-Equation Turbulence Models

The development and implementation of kL-based Reynolds Average Navier-Stokes (RANS) two-equation turbulence models are reported herein. The kL is based on Abdol-Hamid's closure and Menter's modification to Rotta's two-equation model. Rotta shows that a reliable transport equation can be formed from the turbulent length scale L, and the turbulent kinetic energy k. Rotta's kL equation is well suited for term-by-term modeling and displays useful features compared to other scale formulation. One of the important differences is the inclusion of higher order velocity derivatives in the source terms of the scale equation. This can enhance the ability of RANS solvers to simulate unsteady flows in URANS mode. The present report documents the formulation of two model levels of turbulence models as implemented in the computational fluid dynamics FUN3D code. The levels are the two-equation linear k-kL and the two-equation algebraic Reynolds stress model (ARSM). Free shear, separated and corner flow cases are documented and compared with experimental, and other turbulence model data. The results show generally very good comparisons with experimental data. The results from this formulation are similar or better than results using the SST two-equation turbulence model. ARSM shows great promise with similar level of computational resources as basic two-equation turbulence models.

Abdol-Hamid, K. S.↗
NASA NTRS2020

Juncture Flow Computations using kL-Based Turbulence Models

The development and implementation of kL-based Reynolds-Average Navier-Stokes (RANS) two-equation turbulence models are reported in this paper. The kL model is based on Abdol-Hamid's closure and Menter's modification to Rotta's two-equation model. Rotta showed that a reliable transport equation can be formed from the turbulence length scale L, and the turbulence kinetic energy k. Rotta's kL equation is well suited for a term-by-term modeling and displays useful features compared to other scale formulations. One of the important differences is the inclusion of higher-order velocity derivatives in the source terms of the scale equation. This can enhance the ability of RANS solvers to simulate unsteady flows in URANS mode. The k-kL scheme has been modified to include the Algebraic Reynolds Stress Model (ARSM) and the Quadratic Constitutive Relation (QCR) as nonlinear models. These models have gone through extensive validations using two-dimensional benchmark problems. The present study documents the application of the k-kL schemes to simulate flow around the Juncture Flow Model (JFM). The k-kL prediction results show generally good comparisons with measurements. The results from this formulation are similar to, or better than results using the SA-RC-QCR2000 two-equation turbulence model. The ARSM and the QCR formulations of k-kL show promise with a similar level of computational resources as basic two-equation turbulence models.

K S Abdol-Hamid↗
NASA NTRS1976

Atmospheric flow over two-dimensional bluff surface obstructions

The phenomenon of atmospheric flow over a two-dimensional surface obstruction, such as a building (modeled as a rectangular block, a fence or a forward-facing step), is analyzed by three methods: (1) an inviscid free streamline approach, (2) a turbulent boundary layer approach using an eddy viscosity turbulence model and a horizontal pressure gradient determined by the inviscid model, and (3) an approach using the full Navier-Stokes equations with three turbulence models; i.e., an eddy viscosity model, a turbulence kinetic-energy model and a two-equation model with an additional transport equation for the turbulence length scale. A comparison of the performance of the different turbulence models is given, indicating that only the two-equation model adequately accounts for the convective character of turbulence. Turbulence flow property predictions obtained from the turbulence kinetic-energy model with prescribed length scale are only insignificantly better than those obtained from the eddy viscosity model. A parametric study includes the effects of the variation of the characteristics parameters of the assumed logarithmic approach velocity profile. For the case of the forward-facing step, it is shown that in the downstream flow region an increase of the surface roughness gives rise to higher turbulence levels in the shear layer originating from the step corner.

Bitte, J.↗