SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Reaction in a rapid compression apparatus was followed by pressure recording, by photography, and by sampling and chemical analysis. It was possible to investigate the highly sensitive hydrogen-oxygen reaction with this equipment. Results obtained with this reaction make it highly improbable that any hot-point effects are present, Detailed results are presented for single or two-stage ignition of hydrocarbons with air.
Experimental observations of two-stage, autoignition characteristics of fiber-supported, n-dodecane fuel droplets under normal gravity are reported for a wide range of ambient temperatures, and pressures varying from 1 atm to 25 atm, which encompasses the fuel critical pressure (~ 18 atm). A high-speed camera is used to obtain backlit images of the autoignition process. During two-stage ignition, a cool-flame front forms below the droplet in the natural convective plume of the fuel vapor originating from the vaporizing droplet, and propagates upward, followed by the formation of a hot-flame kernel that expands rapidly and surrounds the droplet, eventually leading to the classical diffusion flame. Experimentally measured cool, and hot flame formation locations and propagation speeds are presented for varying initial temperatures and pressures. Measured first, and second stage ignition delay times are also reported. The influences of negative temperature coefficient (NTC) regime chemistry on flame starting location, propagation speeds, and ignition delay times are described. The first-stage cool flame characteristics are found to be controlled by both the chemistry, and physical aspects such as droplet evaporation and fuel-oxidizer mixing, while the second-stage hot flame ignition is primarily controlled by chemical kinetics. Further work is currently underway to develop models to quantitatively predict the observed behavior.
An investigation has been conducted of the ignition-containment capability of 12 oxygen regulators contaminated by various levels of hydrocarbon oils and subjected to promoted ignition. The regulators inlets were pressurized to 15.2 MPa with gaseous oxygen, and the oil was ignited by an electrical arc located upstream of the test article inlet port; the flame was allowed to propagate with the oxygen flow throughout the regulator internal cavities. The resulting reactions, which ranged in character from complete containment of the promoted ignition for one two-stage regulator to extensive burning and explosive energy release for several other (both single- and double-stage) regulators, indicate the need to prevent oil from being introduced into regulators.
In support of NASA's efforts to advance methane technology for future exploration missions, two different igniter concepts were developed and tested at NASA's Marshall Space Flight Center for ignition of oxygen/methane propellants. The first type of igniter, an impinging injection, spark-initiated torch igniter (impinging igniter), used traditional spark plug technology to produce a small, but very intense, pulsed plasma as the ignition source. The second type of igniter, a microwave-generated plasma igniter (microwave igniter), used a microwave magnetron to produce a continuous, larger-volume plasma as the ignition source. Two new designs for both types of igniters were leveraged off past oxygen/methane igniter designs that were tested at MSFC and documented in a 2008 JANNAF paper. In this most recent work, the two new igniters were to be tested at the component level as well as inside a liquid oxygen/liquid methane (LOX/LCH4) 40-element swirl coaxial injector. Although the microwave igniter achieved ignition in every test, it encountered technical difficulties that prevented it from being tested with the injector. The impinging igniter required several design iterations as well as testing at different mixture ratios and mass flow rates before reliable operation with minimal ignition delay was achieved. The final design of the impinging igniter was successfully tested in the LOX/LCH4 injector. The same igniter was later re-configured and component-tested to demonstrate reliable ignition of oxygen/hydrogen propellants. Future tests of the impinging igniter will include ignition of a LOX/hydrogen two-stage swirl injector, which is one of several injector concepts being tested in the Lunar Lander Descent Engine Test Bed at MSFC. All igniter and injector tests have been funded by the Propulsion & Cryogenics Advanced Development project managed by Glenn Research Center and sponsored by NASA s Exploration Technology Development Program.
Recent theoretical and experimental studies concerned with detonation and pressure wave combustion interaction, fire and explosion research and safety, heterogeneous combustion, flame-flow interactions, kinetics of elementary reactions, pollution control in and by combustion systems, and ignition are presented. Some of the topics covered include critical power density for direct initiation of unconfined gaseous detonations, extinction of laminar diffusion flames for liquid fuels, combustion of bulk titanium in oxygen, flame propagation in small spheres of unconfined and slightly confined flammable mixtures, kinetics of the reaction of nitric oxide with hydrogen, production of chemi-ions and formation of CH and CH2 radicals in methane-oxygen and ethylene-oxygen flames, NOx emission characteristics in two-stage combustion, and spherical ignition of oxyhydrogen behind a reflected shock wave. Individual items are announced in this issue.
A detailed qualitative analysis of the processes leading to the explosive ignition of a reactive liquid droplet that is suspended in a gas-phase oxidizer and subjected to the passage of a shock wave, is presented. The interval of time between shock wave passage and ignition is described by identifying a two-stage process which consists of a period of relative reactive dormancy that is followed by a chemical induction period leading to the thermal explosion of reactant that has been stripped from the liquid drop, vaporized, and mixed with the gas-phase oxidizer. The results of first-order calculations based on this model are presented and compared with experimental data for diethlcyclohexane drops in oxygen.
Fuel-rich catalytic combustion (E.R. greater than 5.0) is a unique technique for preheating a hydrocarbon fuel to temperatures much higher than those obtained by conventional heat exchangers. In addition to producing very reactive molecules, the process upgrades the structure of the fuel by the formation of hydrogen and smaller hydrocarbons and produces a cleaner burning fuel by removing some of the fuel carbon from the soot formation chain. With fuel-rich catalytic combustion as the first stage of a two stage combustion system, enhanced fuel properties can be utilized by both high speed engines, where time for ignition and complete combustion is limited, and engines where emission of thermal NO sub x is critical. Two-stage combustion (rich-lean) has been shown to be effective for NO sub x reduction in stationary burners where residence times are long enough to burn-up the soot formed in the first stage. Such residence times are not available in aircraft engines. Thus, the soot-free nature of the present process is critical for high speed engines. The successful application of fuel-rich catalytic combustion to Jet-A, a multicomponent fuel used in gas turbine combustors, is discusssed.
For the next generation of NASA’s missions, explicit, path-adaptive descent guidance algorithms must provide the stability and customizability required for a safe and efficient descent to the lunar surface, while also meeting program and vehicle constraints. Several descent algorithms have been flown and tested for single-stage landers through the Apollo and Altair programs, but thus far little analysis has been conducted involving the application of these algorithms to a two-stage descent vehicle. Due to payload mass and fairing constraints of the existing fleet of launch vehicles, multi-stage descent architectures are a unique option for achieving the greatest possible mass to lunar surface. This paper seeks to compare the performance of guidance configurations of a lunar lander system consisting of two stages, one of which separates partway through descent. Through development of this paper, an optimization suite has been written that is specifically designed for optimizing planetary non-atmospheric two-stage descent trajectories, and is used as a baseline to compare the guidance algorithms tested. Time-to-go computational methods and ignition logic routines that may be employed in a lunar environment are also discussed. Preliminary results are presented that show relative performance metrics for a range of different guidance algorithm configurations.
For the next generation of NASA’s missions, the necessity for path-adaptive guidance algorithms has become clear in order to provide the stability and customizability required for a safe and efficient descent to the lunar surface, while meeting specified program and vehicle constraints. Several descent algorithms have been tested and flown for single-stage landers through the Apollo and Altair programs, but thus far little analysis has been conducted involving the application of these algorithms for a two-stage descent vehicle. Due to the limited payload mass constraints of the existing fleet of launch vehicles, multi-stage descent architectures have become a viable course of action. This paper seeks to compare the performance of guidance configurations for a lunar lander system consisting of two stages, one of which separates partway through descent. Through development of this paper, an optimization suite has been written that is specifically designed for optimizing planetary non-atmospheric two-stage descent trajectories, and is used as a comparison baseline for the guidance algorithms tested. Time-to -go computational methods and ignition logic routines that may be employed in a lunar environment are also discussed. Further work is to be completed on trajectory design trades as well as the effects of modifying guidance targets in simulation based on trajectories that are optimized for different performance indices.
Solid State Laser Initiated Ordnance (LIO) offers new technology having potential for enhanced safety, reduced costs, and improved operational efficiency. Concerns over the absence of programmatic applications of the technology, which has prevented acceptance by flight programs, should be abated since LIO has now been operationally implemented by the Laser Initiated Ordnance Sounding Rocket Demonstration (LOSRD) Program. The first launch of solid state laser diode LIO at the NASA Wallops Flight Facility (WFF) occurred on March 15, 1995 with all mission objectives accomplished. This project, Phase 3 of a series of three NASA Headquarters LIO demonstration initiatives, accomplished its objective by the flight of a dedicated, all-LIO sounding rocket mission using a two-stage Nike-Orion launch vehicle. LIO flight hardware, made by The Ensign-Bickford Company under NASA's first Cooperative Agreement with Profit Making Organizations, safely initiated three demanding pyrotechnic sequence events, namely, solid rocket motor ignition from the ground and in flight, and flight termination, i.e., as a Flight Termination System (FTS). A flight LIO system was designed, built, tested, and flown to support the objectives of quickly and inexpensively putting LIO through ground and flight operational paces. The hardware was fully qualified for this mission, including component testing as well as a full-scale system test. The launch accomplished all mission objectives in less than 11 months from proposal receipt. This paper concentrates on accomplishments of the ordnance aspects of the program and on the program's implementation and results. While this program does not generically qualify LIO for all applications, it demonstrated the safety, technical, and operational feasibility of those two most demanding applications, using an all solid state safe and arm system in critical flight applications.
A liquid oxygen (LOX) turbopump with an 860 R gaseous oxygen (GOX) turbine drive was designed for a 3750 lb thrust dual expander cycle rocket engine. This turbopump, which requires no interpropellant seals or system purges, features a 156 hp, single stage, full admission, impulse turbine; an axial flow inducer; a two-stage centrifugal pump with unshrouded impellers; long-life, LOX-lubricated, self-aligning, hydrostatic bearings; and a subcritical rotor design. It is constructed of Monel, a nickel-copper alloy, which has low ignition potential in oxygen. The pump was designed to deliver 34.7 gpm of 4655 psia liquid oxygen at a shaft speed of 75,000 rpm. The dual expander cycle rocket engine and the performance it requires of the LOX turbopump will be discussed as well as the design of the pump, turbine, bearings, and the turbopump rotordynamics. The test program and preliminary test results will also be presented.
A well-validated quasi-one-dimensional computational fluid dynamics (CFD) code for the analysis of the internal ballistics of two-stage light gas guns is modified to explicitly calculate the ablation of steel from the gun bore and the incorporation of the ablated wall material into the hydrogen working cas. The modified code is used to model 45 shots made with the NASA Ames 0.5 inch light gas gun over an extremely wide variety of gun operating conditions. Good agreement is found between the experimental and theoretical piston velocities (maximum errors of +/-2% to +/-6%) and maximum powder pressures (maximum errors of +/-10% with good igniters). Overall, the agreement between the experimental and numerically calculated gun erosion values (within a factor of 2) was judged to be reasonably good, considering the complexity of the processes modelled. Experimental muzzle velocities agree very well (maximum errors of 0.5-0.7 km/sec) with theoretical muzzle velocities calculated with loading of the hydrogen gas with the ablated barrel wall material. Comparison of results for pump tube volumes of 100%, 60% and 40% of an initial benchmark value show that, at the higher muzzle velocities, operation at 40% pump tube volume produces much lower hydrogen loading and gun erosion and substantially lower maximum pressures in the gun. Large muzzle velocity gains (2.4-5.4 km/sec) are predicted upon driving the gun harder (that is, upon using, higher powder loads and/or lower hydrogen fill pressures) when hydrogen loading is neglected; much smaller muzzle velocity gains (1.1-2.2 km/sec) are predicted when hydrogen loading is taken into account. These smaller predicted velocity gains agree well with those achieved in practice. CFD snapshots of the hydrogen mass fraction, density and pressure of the in-bore medium are presented for a very erosive shot.
A technology development program was undertaken to determine if the benefits of hybrid rocket propulsion could be realized for a Mars Ascent Vehicle (MAV) application. Specifically, the goal of this program was to increase the Technology Readiness Level (TRL) of a hybrid propulsion system such that it could be considered for a potential Mars Sample Return Campaign. Over the course of approximately five years, a new, wax-based fuel was developed, characterized and tested with Mixed Oxides of Nitrogen (from MON-3 to MON-25). Various ignition mechanisms were tested and solid hypergolic additives were evaluated for their potential to ignite the hybrid motor. Several hot-fire test campaigns were completed at both sub- and full-scale. The technology development program was born out of a JPL study documented by Shotwell and Karp that identified the Single Stage to Orbit (SSTO) hybrid propulsion system for a potential Mars Ascent Vehicle to be the lowest Gross Lift Off Mass option from the ten configurations evaluated. Benefits of the hybrid option included its predicted favorable low temperature storage and operation behavior, high performance and ability to restart (enabling the SSTO). The main disadvantage of the hybrid option was its low TRL, as it essentially started as a blank sheet design with a new fuel development. Near the end of the technology development program, a Preliminary Architecture Assessment (PAA) was completed to evaluate a single-stage hybrid propulsion system and a two-stage solid propulsion system for a potential MAV. The solid propulsion system was selected for further study in 2019, primarily because of its flight heritage. While the hybrid technology development program made many strides, there was still a list of challenges to overcome. This paper will discuss the substantial progress and remaining challenges from the technology development effort from 2015 through 2019. This includes fuel development and reformulation, sub- and full-scale testing at Space Propulsion Group, full scale testing at Parabilis, full scale testing at Whittinghill Aerospace, hypergolic additive testing at Purdue and Penn State and the evaluation of adding hypergolic additives to a fullscale grain. It also includes a discussion of the design that resulted from the Preliminary Architecture Assessment.
Work continued on the improvement of 16-Inch Shock Tunnel. This comprised studies of ways of improving driver gas ignition, an improved driver gas mixing system, an axial translation system for the driver tube, improved diaphragm materials (carbon steel vs. stainless steel), a copper liner for the part of the driven tube near the nozzle, the use of a buffer gas between the driver and driven gases, the use of N2O in the driven tube, the use of a converging driven tube, operation of the facility as a non-reflected shock tunnel and expansion tube, operation with heated hydrogen or helium driver gas, the use of detonations in the driver and the construction of an enlarged test section. Maintenance and developmental work continued on the scramjet combustor continued. New software which greatly speeds up data analysis has been written and brought on line. In particular, software which provides very rapid generation of model surface heat flux profiles has been brought on line. A considerable amount of theoretical work was performed in connection with upgrading the 16 Inch Shock Tunnel Facility. A one-dimensional Godunov code for very high velocities and any equation of state is intended to add viscous effects in studying the operation of the Shock Tunnel and also of two-stage light gas guns.
A technology development program was undertaken to determine if the benefits of hybrid rocket propulsion could be realized for a Mars Ascent Vehicle (MAV) application. Specifically, the goal of this program was to increase the Technology Readiness Level (TRL) of a hybrid propulsion system such that it could be considered for a potential Mars Sample Return Campaign. Over the course of approximately five years, a new, wax-based fuel was developed, characterized and tested with Mixed Oxides of Nitrogen (from MON-3 to MON-25). Various ignition mechanisms were tested and solid hypergolic additives were evaluated for their potential to ignite the hybrid motor. Several hot-fire test campaigns were completed at both sub- and full-scale. The technology development program was born out of a JPL study documented by Shotwell and Karp that identified the Single Stage to Orbit (SSTO) hybrid propulsion system for a potential Mars Ascent Vehicle to be the lowest Gross Lift Off Mass option from the ten configurations evaluated. Benefits of the hybrid option included its predicted favorable low temperature storage and operation behavior, high performance and ability to restart (enabling the SSTO). The main disadvantage of the hybrid option was its low TRL,as it essentially started as a blank sheet design with a new fuel development. Near the end of the technology development program, a Preliminary Architecture Assessment (PAA) was completed to evaluate a single-stage hybrid propulsion system and a two-stage solid propulsion system for a potential MAV. The solid propulsion system was selected for further study in 2019, primarily because of its flight heritage. While the hybrid technology development program made many strides, there was still a list of challenges to overcome. This paper will discuss the substantial progress and remaining challenges from the technology development effort from 2015 through 2019. This includes fuel development and reformulation, sub- and full-scale testing at Space Propulsion Group, full scale testing at Parabilis, full scale testing at Whittinghill Aerospace, hypergolic additive testing at Purdue and Penn State and the evaluation of adding hypergolic additives to a full-scale grain. It also includes a discussion of the design that resulted from the Preliminary Architecture Assessment.