SEARCH · Search NASA

Results for “uninhabited”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

All sources NASA NTRS DOE OSTI

NASA NTRS2005

Autonomous Soaring for Improved Endurance of a Small Uninhabited Air Vehicle

A relatively unexplored method to improve the endurance of an autonomous aircraft is to use buoyant plumes of air found in the lower atmosphere called thermals or updrafts. Glider pilots and birds commonly use updrafts to improve range, endurance, or cross-country speed. This report presents a quantitative analysis of a small electric-powered uninhabited air vehicle using updrafts to extend its endurance over a target location. A three-degree-of-freedom simulation of the uninhabited air vehicle was used to determine the yearly effect of updrafts on performance. Surface radiation and rawinsonde balloon measurements taken at Desert Rock, Nevada, were used to determine updraft size, strength, spacing, shape, and maximum height for the simulation. A fixed-width spiral path was used to search for updrafts at the same time as maintaining line-of-sight to the surface target position. Power was used only when the aircraft was flying at the lower-altitude limit in search of updrafts. Results show that an uninhabited air vehicle with a nominal endurance of 2 hours can fly a maximum of 14 hours using updrafts during the summer and a maximum of 8 hours during the winter. The performance benefit and the chance of finding updrafts both depend on what time of day the uninhabited air vehicle is launched. Good endurance and probability of finding updrafts during the year was obtained when the uninhabited air vehicle was launched 30 percent into the daylight hours after sunrise each day. Yearly average endurance was found to be 8.6 hours with these launch times.

Allen, Michael J.↗

NASA NTRS1997

An Impact-Location Estimation Algorithm for Subsonic Uninhabited Aircraft

An impact-location estimation algorithm is being used at the NASA Dryden Flight Research Center to support range safety for uninhabited aerial vehicle flight tests. The algorithm computes an impact location based on the descent rate, mass, and altitude of the vehicle and current wind information. The predicted impact location is continuously displayed on the range safety officer's moving map display so that the flightpath of the vehicle can be routed to avoid ground assets if the flight must be terminated. The algorithm easily adapts to different vehicle termination techniques and has been shown to be accurate to the extent required to support range safety for subsonic uninhabited aerial vehicles. This paper describes how the algorithm functions, how the algorithm is used at NASA Dryden, and how various termination techniques are handled by the algorithm. Other approaches to predicting the impact location and the reasons why they were not selected for real-time implementation are also discussed.

Bauer, Jeffrey E.↗

NASA NTRS2006

Updraft Model for Development of Autonomous Soaring Uninhabited Air Vehicles

Large birds and glider pilots commonly use updrafts caused by convection in the lower atmosphere to extend flight duration, increase cross-country speed, improve range, or simply to conserve energy. Uninhabited air vehicles may also have the ability to exploit updrafts to improve performance. An updraft model was developed at NASA Dryden Flight Research Center (Edwards, California) to investigate the use of convective lift for uninhabited air vehicles in desert regions. Balloon and surface measurements obtained at the National Oceanic and Atmospheric Administration Surface Radiation station (Desert Rock, Nevada) enabled the model development. The data were used to create a statistical representation of the convective velocity scale, w*, and the convective mixing-layer thickness, zi. These parameters were then used to determine updraft size, vertical velocity profile, spacing, and maximum height. This paper gives a complete description of the updraft model and its derivation. Computer code for running the model is also given in conjunction with a check case for model verification.

Allen, Michael J.↗

NASA NTRS2024

Standard Operating Procedure (SOP) for Flight Testing a Radiosonde and 3D Sonic Anemometer Configuration on a Multi-rotor Uninhabited Aerial System (UAS)

The purpose of this Standard Operating Procedure (SOP) is to establish a uniform procedure for initialization of a radiosonde, a 3D sonic anemometer, and collection of sounding data with correct sensor integration via a multi-rotor uninhabited aerial system (UAS) within the Langley Research Center’s (LaRC) Uninhabited Aerial System Operations Office (UASOO).

Tyler L. Willhite↗

NASA NTRSDate not supplied

Uninhabited Aerial System Drop-in Balloon-Borne Radiosonde Alternative for Lower Tropospheric Flights

Balloon-borne radiosonde sensors are a well characterized way of gathering data into the stratosphere; however, balloon launches have limitations such as the need to replace the balloon and sensors after each flight, as well the overall drift of the balloon over the course of the launch. Using sensors mounted on an uninhabited aerial system (UAS) allows for higher temporal-resolution vertical profiles in the lower troposphere and allows for full control of the flight profile of the sensors. This paper presents a drop-in solution for a balloon-borne radiosonde in which it is mounted on an uninhabited aerial system in lieu of a balloon with an additional connection to a 3D anemometer streaming atmospheric and wind data in near real-time to a ground station. This alternative platform for balloon-borne radiosondes has undergone extensive flight testing with the wind results being compared against a ground-based wind LiDAR for validation and the atmospheric results undergoing further data analysis against a wide variety of sensors for future validation. Indoor tests were also conducted and are discussed in order to determine the propeller’s influence on the anemometer. This alternative platform will allow for higher temporal and spatial resolution of atmospheric data collection in near-real time.

Tyler L. Willhite↗

NASA NTRS1998

Operational Concepts for Uninhabited Tactical Aircraft

This paper describes experiences with five remotely piloted flight research vehicle projects in the developmental flight test phase. These projects include the Pathfinder, Perseus B, Altus, and X-36 aircraft and the Highly Maneuverable Aircraft Technology (HiMAT). Each of these flight projects was flown at the NASA Dryden Flight Research Center. With the exception of the HiMAT, these projects are a part of the Flight Research Base Research and Technology (R&T) Program of the NASA Aeronautics and Space Transportation Technology Enterprise. Particularly with respect to operational interfaces between the ground-based pilot or operator, this paper draws from those experiences, then provides some rationale for extending the lessons learned during developmental flight research to the possible situations involved in the developmental flights proceeding deployed uninhabited tactical aircraft (UTA) operations. Two types of UTA control approaches are considered: autonomous and remotely piloted. In each of these cases, some level of human operator or pilot control blending is recommended. Additionally, "best practices" acquired over years of piloted aircraft experience are drawn from and presented as they apply to operational UTA.

Deets, Dwain A.↗

NASA NTRS1998

Operational Concepts for Uninhabited Tactical Aircraft

This paper describes experiences with five remotely piloted flight research vehicle projects in the developmental flight test phase. These projects include the Pathfinder, Perseus B, Altus, and X-36 aircraft and the Highly Maneuverable Aircraft Technology (HiMAT). Each of these flight projects was flown at the NASA Dryden Flight Research Center. With the exception of the HIMAT, these projects are a part of the Flight Research Base Research and Technology (R&T) Program of the NASA Aeronautics and Space Transportation Technology Enterprise. Particularly with respect to operational interfaces between the ground-based pilot or operator, this paper draws from those experiences, then provides some rationale for extending the lessons learned during developmental flight research to the possible situations involved in the developmental flights proceeding deployed uninhabited tactical aircraft (UTA) operations. Two types of UTA control approaches are considered: autonomous and remotely piloted. In each of these cases, some level of human operator or pilot control blending is recommended. Additionally, "best practices" acquired over years of piloted aircraft experience are drawn from and presented as they apply to operational UTA.

Deets, Dwain A.↗

NASA NTRS2002

An Examination of Drag Reduction Mechanisms in Marine Animals, with Potential Applications to Uninhabited Aerial Vehicles

Previous engineering research and development has documented the plausibility of applying biomimetic approaches to aerospace engineering. Past cooperation between the Virginia Institute of Marine Science (VIMS) and NASA focused on the drag reduction qualities of the microscale dermal denticles of shark skin. This technology has subsequently been applied to submarines and aircraft. The present study aims to identify and document the three-dimensional geometry of additional macroscale morphologies that potentially confer drag reducing hydrodynamic qualities upon marine animals and which could be applied to enhance the range and endurance of Uninhabited Aerial Vehicles (UAVs). Such morphologies have evolved over eons to maximize organismal energetic efficiency by reducing the energetic input required to maintain cruising speeds in the viscous marine environment. These drag reduction qualities are manifested in several groups of active marine animals commonly encountered by ongoing VIMS research programs: namely sharks, bony fishes such as tunas, and sea turtles. Through spatial data acquired by molding and digital imagery analysis of marine specimens provided by VIMS, NASA aims to construct scale models of these features and to test these potential drag reduction morphologies for application to aircraft design. This report addresses the efforts of VIMS and NASA personnel on this project between January and November 2001.

Musick, John A.↗

NASA NTRS2001

Use of Acoustic Wind Profilers for Uninhabited Aerial Vehicle Flight Test Activities

Sonic detection and ranging (SODAR) systems provide crucial information to meteorologists for advising uninhabited aerial vehicle (UAV) flight crews and mission directors on historical, current, and forecasted wind and turbulence conditions. The SODAR system provided advanced warning of increasing surface winds for an X-38 flight on February 6, 1999. The SODAR system has also provided important postflight data for X-38 engineers to review the performance of the parafoil in the presence of strong wind shears near the surface at landing.

Donnohue, Casey J.↗

NASA NTRS2003

Distributed Actuation and Sensing on an Uninhabited Aerial Vehicle

An array of effectors and sensors has been designed, tested and implemented on a Blended Wing Body Uninhabited Aerial Vehicle (UAV). The UAV is modified to serve as a flying, controls research, testbed. This effector/sensor array provides for the dynamic vehicle testing of controller designs and the study of decentralized control techniques. Each wing of the UAV is equipped with 12 distributed effectors that comprise a segmented array of independently actuated, contoured control surfaces. A single pressure sensor is installed near the base of each effector to provide a measure of deflections of the effectors. The UAV wings were tested in the North Carolina State University Subsonic Wind Tunnel and the pressure distribution that result from the deflections of the effectors are characterized. The results of the experiments are used to develop a simple, but accurate, prediction method, such that for any arrangement of the effector array the corresponding pressure distribution can be determined. Numerical analysis using the panel code CMARC verifies this prediction method.

Barnwell, William Garrard↗

NASA NTRS2006

Rapid, Repeat-sample Monitoring of Crustal Deformations and Environmental Phenomena with the Uninhabited Aerial Vehicle Synthetic Aperture Radar

The Uninhabited Aerial Vehicle Synthetic Aperture Radar (UAVSAR) is a precision repeat-pass Interferometric Synthetic Aperture Radar (InSAR) mission being developed by the Jet Propulsion Laboratory and the Dryden Flight Research Center in support of NASA s Science Mission Directorate. UAVSAR's unique ability to fly a repeatable flight path, along with an electronically steerable array, allows interferometric data to be obtained with accuracies measured in millimeters. Deploying the radar on an airborne platform will also allow for radar images to be collected and compared with images from the same area taken hours or even years later - providing for long-term trending and near real-time notification of changes and deformations. UAVSAR s data processing algorithms will provide for near-real time data reduction providing disaster planning and response teams with highly accurate data to aid in the prediction of, and response to, natural phenomena. UAVSAR data can be applied to increasing our understanding of the processes behind solid earth, cryosphere, carbon cycle and other areas of interest in earth science. Technologies developed for UAVSAR may also be applicable to a future earth-orbiting InSAR mission and possibly for missions to the Moon or Mars. The UAVSAR is expected to fly on a Gulfstream III aircraft this winter, followed by a flight test program lasting until the second half of 2007. Following radar calibration and data reduction activities, the platform will be ready for science users in the summer of 2008.

Smith, Robert C.↗

NASA NTRS2010

Moments of Inertia - Uninhabited Aerial Vehicle (UAV) Dryden Remotely Operated Integrated Drone (DROID)

The objective of this research effort is to determine the most appropriate, cost efficient, and effective method to utilize for finding moments of inertia for the Uninhabited Aerial Vehicle (UAV) Dryden Remotely Operated Integrated Drone (DROID). A moment is a measure of the body's tendency to turn about its center of gravity (CG) and inertia is the resistance of a body to changes in its momentum. Therefore, the moment of inertia (MOI) is a body's resistance to change in rotation about its CG. The inertial characteristics of an UAV have direct consequences on aerodynamics, propulsion, structures, and control. Therefore, it is imperative to determine the precise inertial characteristics of the DROID.

Haro, Helida C.↗

NASA NTRS2010

Moments of Inertia: Uninhabited Aerial Vehicle (UAV) Dryden Remotely Operated Integrated Drone (DROID)

Haro, Helida C.↗

NASA NTRS2019

"Sensor Web Evolution - Webs of Webs for NASA Science - Focus on small Uninhabited Aerial Systems (sUAS)"

This paper will describe the evolution of information collection, derivation and delivery mechanisms in webs of NASA sensor webs, with a focus on recent advancements in small Uninhabited Aerial Systems (sUAS). I will discuss the movement to "Fog Computing", also known as Edge Computing. Fog Computing facilitates the distribution of common operations and networking between edge devices and cloud computing facilities, optimizing the production of actionable intelligence. Initially, sUASs utilized onboard data collection as standard, with minimal data downloaded directly. Information products were derived in conventional computational environments, generally desk top computers, and information products made available to the Science Community in weeks or months. With the increased availability, and increasingly lower costs, of beyond line of sight (BLOS) satellite based communication, transmission rates and data volumes increased, and processing migrated to Cloud based services. Contemporary sUASs are moving some of that information product derivation to on vehicle services, and are creating a distributed Cloud/Fog environment. I will describe the technological advances that have made this possible, including low power multi-core Central Processing Units (CPU), and, more recently, the availability of high end Graphical Processing Units (GPU) that consume only a few watts. Intelligent system software, leveraging these hardware advances, finally allows for information product generation on-board, rather than simple data collection. Additionally, intelligent flight control systems now support mutual vehicle to vehicle collaboration, allowing sUASs to create ad-hoc sensor webs on demand, as required. Also discussed will be the lessons learned by the Authors' development of data systems for NASA's large High Altitude Long Endurance (HALE) UASs like Predator and Global Hawk, and how those lessons are being applied to sUAS development. This paper will focus on application, rather a deep dive into the technology, and will highlight improving data management through these new technologies.

Sensor Web↗

NASA NTRSDate not supplied

Use of an Uninhabited Aircraft System (UAS) for Atmospheric Observations During an Acoustic Flight Test

A jet noise test was performed at Niagara Falls International Airport using a Calspan Learjet 25 by acoustics researchers at NASA Glenn Research Center in partnership with Calspan personnel and Uninhabited Aircraft Systems (UAS) pilots and sensor operators from NASA Langley Research Center. To account for atmospheric attenuation in the de-propagation of jet noise from a ground-based microphone array to the source for comparison with model data collected in a facility at NASA GRC, a vertical profile of atmospheric conditions was required. To that end, a sUAS was flown with a weather sensor package measuring atmospheric pressure, humidity, and temperature in a range of altitudes from ground level to 304.8 m (1,000 ft) above ground level (AGL). The sUAS flights were performed concurrently with and adjacent to the Learjet flight path. Data from these UAS flights are presented herein; additionally, comparisons with conventional balloon-borne instrumentation are made with a particular focus on the quality and capability of UAS-based observations for acoustic flight test applications. Furthermore, a ground-based light detection and ranging (LiDAR) system was deployed for collecting wind magnitude and direction for discrete altitudes up to 304.8 m (1,000 ft) AGL. Data from the LiDAR unit will be presented and discussed in the context of aircraft acoustic flight testing. This effort was supported by NASA’s Commercial Supersonic Technology project.

UAS↗

NASA NTRS2001

Human-Vehicle Interface for Semi-Autonomous Operation of Uninhabited Aero Vehicles

The robustness of autonomous robotic systems to unanticipated circumstances is typically insufficient for use in the field. The many skills of human user often fill this gap in robotic capability. To incorporate the human into the system, a useful interaction between man and machine must exist. This interaction should enable useful communication to be exchanged in a natural way between human and robot on a variety of levels. This report describes the current human-robot interaction for the Stanford HUMMINGBIRD autonomous helicopter. In particular, the report discusses the elements of the system that enable multiple levels of communication. An intelligent system agent manages the different inputs given to the helicopter. An advanced user interface gives the user and helicopter a method for exchanging useful information. Using this human-robot interaction, the HUMMINGBIRD has carried out various autonomous search, tracking, and retrieval missions.

Jones, Henry L.↗

NASA NTRS2003

Application of Artificial Intelligence Techniques in Uninhabitated Aerial Vehicle Flight

This paper describes the development of an application of Artificial Intelligence (AI) for Unmanned Aerial Vehicle (UAV) control. The project was done as part of the requirements for a class in AI at NOVA southeastern University and a beginning project at NASA Wallops Flight Facility for a resilient, robust, and intelligent UAV flight control system. A method is outlined which allows a base level application for applying an Artificial Intelligence method, Fuzzy Logic, to aspects of Control Logic for UAV flight. One element of UAV flight, automated altitude hold, has been implemented and preliminary results displayed.

Dufrene, Warren R., Jr.↗

NASA NTRS2004

Application of Artificial Intelligence Techniques in Uninhabited Aerial Vehicle Flight

This paper describes the development of an application of Artificial Intelligence (AI) for Unmanned Aerial Vehicle (UAV) control. The project was done as part of the requirements for a class in AI at NOVA Southeastearn University and a beginning project at NASA Wallops Flight Facility for a resilient, robust, and intelligent UAV flight control system. A method is outlined which allows a base level application for applying an Artificial Intelligence method, Fuzzy Logic, to aspects of Control Logic for UAV flight. One element of UAV flight, automated altitude hold, has been implemented and preliminary results displayed.

Dufrene, Warren R., Jr.↗