Search NASA⌕ Search

SEARCH · Search NASA

Results for “view factor models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Multiple-angle observations of reflectance anisotropy from an airborne linear array sensor

An airborne pointable imaging multispectral linear array sensor has been developed for the multidirectional observation of surface reflectance anisotropy. The sensor design permits observations up to 45 deg off-nadir in three spectral bands (green, red, and near-infrared). Calibration permits the conversion of sensor data to radiance units with an absolute uncertainty of 6 percent. Observations of five field plots from seven view directions are discussed. Calibration and atmospheric corrections are used to derive hemispherical-directional reflectance factors. A three-term reflectance model is fit to the reflectance factors for each plot to represent the continuous distribution of reflectance factors with view direction. The reflectance model is integrated over all view directions to calculate bihemispherical reflectance factors. The calculated bihemispherical factors differed by 1 to 25 percent from values based on an assumption of isotropic reflectance depending on spectral band and field plot. These calculations demonstrate the technologic and scientific capabilities required for the remote characterization of surface reflectance anisotropy. Remote multidirectional observations are both feasible and needed to fully evaluate land reflectance characteristics.

Irons, James R.↗
NASA NTRSDate not supplied

An Approach to Solving Enclosure Radiation Problems in A Multi-Physics Context

Thermal protection system analysis of complex features or damage sites can sometimes require modeling of high temperature enclosures. Implementing efficient and accurate view-factor algorithms required to model such problems is complex. The current work leverages the Non-equilibrium Radiation (NERO) software, which solves the radiation transport equation in a finite-volume scheme, to alleviating challenges often faced with view-factor calculations. By assuming heat transfer occurs only between grey bodies and that the medium is non-participating, computational cost of the method is significantly reduced. The enclosure physics are modeled through emitting and reflecting boundary conditions in NERO. The emitted radiative flux is dependent on the wall temperature which is a solution to the material response, obtained from Icarus, in this context. The Ares framework manages the time-advancement and exchange of the necessary data between the solvers. The surface energy balance is modified to account for the enclosure terms within the material response boundary condition. The methodology was verified against analytical solutions including radiating parallel plates, a hollow cylinder (shown in Fig. 1), and a hemisphere. Application of the methodology to inform the design of components of the Dragonfly system will be shown.

Ablation↗
NASA NTRS2016

Impacts of the Angular Dependence of the Solar Diffuser BRDF Degradation Factor on the SNPP VIIRS Reflective Solar Band On-Orbit Radiometric Calibration

Using an onboard sunlit solar diffuser (SD) as the primary radiance source, the visible infrared imaging radiometer suite (VIIRS) on the Suomi National Polar-orbiting Partnership satellite regularly performs radiometric calibration of its reflective solar bands (RSBs). The SD bidirectional reflectance distribution function (BRDF) value decreases over time. A numerical degradation factor is used to quantify the degradation and is determined by an onboard SD stability monitor (SDSM), which observes the sun and the sunlit SD at almost the same time. We had shown previously that the BRDF degradation factor was angle-dependent. Consequently, due to that the SDSM and the RSB view the SD at very different angles relative to both the solar and the SD surface normal vectors, directly applying the BRDF degradation factor determined by the SDSM to the VIIRS RSB calibration can result in large systematic errors. We develop a phenomenological model to calculate the BRDF degradation factor for the RSB SD view from the degradation factor for the SDSM SD view. Using the yearly undulations observed in the VIIRS detector gains for the M1-M4 bands calculated with the SD BRDF degradation factor for the SDSM SD view and the difference between the VIIRS detector gains calculated from the SD and the lunar observations, we obtain the model parameter values and thus establish the relation between the BRDF degradation factors for the RSB and the SDSM SD view directions.

Lei, Ning↗
NASA NTRS1978

Space shuttle main engine plume radiation model

The methods are described which are used in predicting the thermal radiation received by space shuttles, from the plumes of the main engines. Radiation to representative surface locations were predicted using the NASA gaseous plume radiation GASRAD program. The plume model is used with the radiative view factor (RAVFAC) program to predict sea level radiation at specified body points. The GASRAD program is described along with the predictions. The RAVFAC model is also discussed.

Reardon, J. E.↗
NASA NTRS1991

Thermal design, testing, and analysis of the Cosmic Background Explorer's external calibrator

The thermal design of a calibrator used to correlate the collected data with an absolute reference onboard of the Cosmic Background Explorer is considered. Since flight conditions could not be simulated in ground testing, the design was qualified by analysis and testing. The requirements imposed on the calibrator are outlined, along with spacecraft hardware modifications aimed at reducing the thermal load on the calibrator. A geometric mathematical model created in order to obtain view factors from the cryogenic instruments to the spacecraft and dewar is discussed. It is shown that the calibrator met or exceeded all of its performance requirements, and that the modifications to such energy sources as the thermal shield and differential microwave radiometers proved effective in reducing the radiative energy the calibrator received from the spacecraft to acceptable levels.

Mosier, Carol L.↗
NASA NTRS2013

Derivation of Sky-View Factors from LIDAR Data

The use of Lidar (Light Detection and Ranging), an active light-emitting instrument, is becoming increasingly common for a range of potential applications. Its ability to provide fine resolution spatial and vertical resolution elevation data makes it ideal for a wide range of studies. This paper demonstrates the capability of Lidar data to measure sky view factors (SVF). The Lidar data is used to generate a spatial map of SVFs which are then compared against photographically-derived SVF at selected point locations. At each location three near-surface elevations measurements were taken and compared with collocated Lidar-derived estimated. It was found that there was generally good agreement between the two methodologies, although with decreasing SVF the Lidar-derived technique tended to overestimate the SVF: this can be attributed in part to the spatial resolution of the Lidar sampling. Nevertheless, airborne Lidar systems can map sky view factors over a large area easily, improving the utility of such data in atmospheric and meteorological models.

spatial map↗
NASA NTRS1988

A Methodology for Multiple Rule System Integration and Resolution Within a Singular Knowledge Base

Expert Systems which support knowledge representation by qualitative modeling techniques experience problems, when called upon to support integrated views embodying description and explanation, especially when other factors such as multiple causality, competing rule model resolution, and multiple uses of knowledge representation are included. A series of prototypes are being developed to demonstrate the feasibility of automating the process of systems engineering, design and configuration, and diagnosis and fault management. A study involves not only a generic knowledge representation; it must also support multiple views at varying levels of description and interaction between physical elements, systems, and subsystems. Moreover, it will involve models of description and explanation for each level. This multiple model feature requires the development of control methods between rule systems and heuristics on a meta-level for each expert system involved in an integrated and larger class of expert system. The broadest possible category of interacting expert systems is described along with a general methodology for the knowledge representation and control of mutually exclusive rule systems.

Kautzmann, Frank N., III↗
NASA NTRS1977

Significance of vegetation in interpreting thermal radiation from a terrestrial surface

The regions between crop rows are modeled as infinitely long diffuse cavities. Geometrical view factors are calculated, accounting for reflected radiation emanating internal to the cavity and from the background sky. A 'cavity' emissivity dependent on local geometry is defined to allow for correcting apparent temperatures to true temperatures. The total emissivity appropriate for correcting aircraft thermal data is then calculated by averaging all emissivity components to account for soil, crop, and background. It is shown that even for the lowest crop and vegetation emissivities, if the crop height-to-spacing ratio is greater than unity, the composite emissivity is greatly increased, giving rise to a decreased error in remotely sensed temperature data.

Sutherland, R. A.↗
NASA NTRS1992

Space Transfer Concepts and Analyses for Exploration Missions. Technical Directive 12: Beamed Power Systems Study

Parametric models were constructed for Earth-based laser powered electric orbit transfer from low Earth orbit to geosynchronous orbit. These models were used to carry out performance, cost/benefit, and sensitivity analyses of laser-powered transfer systems including end-to-end life cycle cost analyses for complete systems. Comparisons with conventional orbit transfer systems were made indicating large potential cost savings for laser-powered transfer. Approximate optimization was done to determine best parameter values for the systems. Orbit transfer flights simulations were conducted to explore effects of parameters not practical to model with a spreadsheet. The simulations considered view factors that determine when power can be transferred from ground stations to an orbit transfer vehicle and conducted sensitivity analyses for numbers of ground stations, Isp including dual-Isp transfers, and plane change profiles. Optimal steering laws were used for simultaneous altitude and plane change. Viewing geometry and low-thrust orbit raising were simultaneously simulated. A very preliminary investigation of relay mirrors was made.

Eder, D.↗
NASA NTRS1990

The beam filling error in the Nimbus 5 electronically scanning microwave radiometer observations of Global Atlantic Tropical Experiment rainfall

A comparison of rain rates retrieved from the Nimbus 5 electronically scanning microwave radiometer brightness temperatures and observed from shipboard radars during the Global Atlantic Tropical Experiment (GATE) phase I shows that the beam filling error is the major source of discrepancy between the two. When averaged over a large scene (the GATE radar array, 400 km in diameter), the beam filling error is quite stable, being 50 percent of the observed rain rate. This suggests the simple procedure of multiplying retrieved rain rates by 2 (correction factor). A statistical model of the beam filling error is developed by envisioning an idealized instrument field-of-view that encompasses an entire gamma distribution of rain rates. A modeled correction factor near 2 is found for rain rate and temperature characteristics consistent with GATE conditions. The statistical model also suggests that the correction factor varies from 1.5 to 2.5 for suppressed to enhanced tropical convective regimes, and decreases to 1.5 as the freezing level and average depth of the rain column decreases to 2.5 km.

Short, David A.↗
NASA NTRS2012

Urban Climate Station Site Selection Through Combined Digital Surface Model and Sun Angle Calculations

Meteorological measurements within urban areas are becoming increasingly important due to the accentuating effects of climate change upon the Urban Heat Island (UHI). However, ensuring that such measurements are representative of the local area is often difficult due to the diversity of the urban environment. The evaluation of sites is important for both new sites and for the relocation of established sites to ensure that long term changes in the meteorological and climatological conditions continue to be faithfully recorded. Site selection is traditionally carried out in the field using both local knowledge and visual inspection. This paper exploits and assesses the use of lidar-derived digital surface models (DSMs) to quantitatively aid the site selection process. This is acheived by combining the DSM with a solar model, first to generate spatial maps of sky view factors and sun-hour potential and second, to generate site-specific views of the horizon. The results show that such a technique is a useful first-step approach to identify key sites that may be further evaluated for the location of meteorological stations within urban areas.

digital surface model↗
NASA NTRS1985

Thermal-capillary model for Czochralski growth of semiconductor materials

The success of efficiently calculating the temperature field, crystal radius, melt mensicus, and melt/solid interface in the Czochralski crystal growth system by full finite-element solution of the government thermal-capillary model is demonstrated. The model predicts realistic response to changes in pull rate, melt volume, and the thermal field. The experimentally observed phenomena of interface flipping, bumping, and the difficulty maintaining steady-state growth as the melt depth decreases are explained by model results. These calculations will form the basis for the first quantitative picture of Cz crystal growth. The accurate depiction of the melt meniscus is important in calculating the crystal radius and solidification interface. The sensitivity of the results to the equilibrium growth angle place doubt on less sophisticated attempts to model the process without inclusion of the meniscus. Quantitative comparison with experiments should be possible once more representation of the radiation and view factors in the thermal system and the crucible are included. Extensions of the model in these directions are underway.

Derby, J. J.↗
NASA NTRS1987

Effect of element size on the solution accuracies of finite-element heat transfer and thermal stress analyses of space shuttle orbiter

The effect of element size on the solution accuracies of finite-element heat transfer and thermal stress analyses of space shuttle orbiter was investigated. Several structural performance and resizing (SPAR) thermal models and NASA structural analysis (NASTRAN) structural models were set up for the orbiter wing midspan bay 3. The thermal model was found to be the one that determines the limit of finite-element fineness because of the limitation of computational core space required for the radiation view factor calculations. The thermal stresses were found to be extremely sensitive to a slight variation of structural temperature distributions. The minimum degree of element fineness required for the thermal model to yield reasonably accurate solutions was established. The radiation view factor computation time was found to be insignificant compared with the total computer time required for the SPAR transient heat transfer analysis.

Ko, William L.↗
NASA NTRS2023

Shape from spectra

We introduce a new unified atmospheric–topographic correction approach that estimates surface geometry directly from the radiance measurement. Surface topography influences the at-sensor radiance measurement, making precise topography modeling critical in applications like vegetation or snow studies in mountainous terrain. Currently, elevation maps are used to derive topographic variables such as the slope and sky-view factor. This process is error-prone since static global digital elevation models do not generally achieve the accuracy required, and even minor mismatches in spatial resolution can introduce significant artifacts in downstream processing. Here we demonstrate that it is possible to estimate topographic parameters directly from spectral data, ensuring perfect physical consistency, temporal coincidence, and spatial alignment. We present experiments estimating topographic slope in two scenes in Southern California, with data from NASA’s Next Generation Airborne Visible/Near Infrared Imaging Spectrometer (AVIRIS-NG). We compared our radiance-based estimates against high-resolution lidar datasets. Our initial validation result showed a correlation of R 2 = 0.864 (n = 160) over the homogeneous surface of Beckman Auditorium’s cone-shaped roof on the Caltech campus in Pasadena, California. We then validate the model over a larger study site near Santa Clarita, California, finding R 2 = 0.923 (n = 40,000) in a 350 x 350m area. The accuracy of our model estimates, combined with its systematic advantages over the alternative, show the potential of the approach for use in both airborne campaigns and orbital missions.

Nimrod Carmon↗
NASA NTRS2021

Positional Dependence of SNPP VIIRS Solar Diffuser BRDF Change Factor: An Empirical Approach

The Earth-observing Visible Infrared Imaging Radiometer Suite (VIIRS) on the Suomi National Polar-orbiting Partnership satellite regularly performs on-orbit radiometric calibration of its reflective solar bands (RSBs), primarily through observations of an onboard sunlit solar diffuser (SD). The on-orbit change of the SD bidirectional reflectance distribution function (BRDF) value, quantified by a numerical factor called the H-factor, is determined by the onboard SD stability monitor. Our previous study showed that the H-factor is solar angle and view direction dependent. In this study, we determine the dependence of the H-factor on the detector SD view footprint location. We fit an empirical model to the NASA Collection 1 SNPP VIIRS Level 1B (L1B) spectral reflectance difference across the detectors in an RSB over uniform Earth scenes of the Libya 4 desert and deep convective clouds. We apply the model predicted SD positional dependent H-factor to calibrate the RSBs. Under this new calibration scheme, the original unreal striping is removed from the homogeneous Libya 4 desert and the deep convective cloud images, as well as the original unreal striping from the Dunhuang desert image. The SD positional dependent H-factor has been used to calculate the SNPP VIIRS RSB radiometric correction factor for the NASA Collection 2.0 SNPP VIIRS L1B products.

SNPP VIIRS↗
NASA NTRS1983

Radiation exchange in large space structures and frames

The analysis of radiation heat transfer is determined by the need to determine the geometrical quantity, F(ij), which is commonly called the view factor, and which represents the fraction of energy leaving surface i which strikes surface j. The present investigation shows that the use of a rotating plane to model a one-dimensional radiation element is both computationally efficient and accurate. Because of the reduced computational cost of this element, radiation view factors for complex structures can be calculated directly. Under some conditions, the characteristics of the one-dimensional element may lead to a loss in accuracy when it is used to model obstructing cylinders. In cases in which the element is too close to the radiating surfaces, curved surfaces must be represented by a collection of flat planes. However, it appears that as long as the one-dimensional element is more than 5 diameters from the other surfaces, its use is valid.

Emery, A. F.↗
NASA NTRSDate not supplied

MISR Level 2 Surface parameters (MIL2ASLS_V2)

The Land Surface data include bihemispherical and directional-hemispherical reflectances (albedo), hemispherical directional and bidirectional reflectance factors (BRF), BRF model parameters, leaf-area index (LAI), fraction of photosynthetically active radiation (FPAR), and normalized difference vegetation index (NDVI) on a 1.1 km grid. The land surface data include hemispherical directional reflectance factor, bihemispherical reflectance (i.e., albedo), bidirectional reflectance factor, directional hemispherical reflectance, BRF model parameters, FPAR, and terrain-referenced view and illumination angles. [Location=GLOBAL LAND] [Temporal_Coverage: Start_Date=2000-02-24; Stop_Date=] [Spatial_Coverage: Southernmost_Latitude=-90; Northernmost_Latitude=90; Westernmost_Longitude=-180; Easternmost_Longitude=180] [Data_Resolution: Latitude_Resolution=1.1 km - 17.6 km; Longitude_Resolution=1.1 km - 17.6 km; Horizontal_Resolution_Range=1 km - < 10 km or approximately .01 degree - < .09 degree; Temporal_Resolution=about 15 orbits/day; Temporal_Resolution_Range=Daily - < Weekly, Daily - < Weekly].

BIDIRECTIONAL REFLECTANCE FACTOR↗
NASA NTRS1993

Virtual egocenters as a function of display geometric field of view and eye station point

The accurate location of one's virtual egocenter in a geometric space is of critical importance for immersion technologies. This experiment was conducted to investigate the role of field of view (FOV) and observer station points in the perception of the location of one's egocenter (the personal viewpoint) in virtual space. Rivalrous cues to the accurate location of one's egocenter may be one factor involved in simulator sickness. Fourteen subjects viewed an animated 3D model, of the room in which they sat, binocularly, from Eye Station Points (ESP) of either 300 or 800 millimeters. The display was on a 190 by 245 mm monitor, at a resolution of 320 by 200 pixels with 256 colors. They saw four models of the room designed with four geometric field of view (FOVg) conditions of 18, 48, 86, and 140 degrees. They drew the apparent paths of the camera in the room on a bitmap of the room as seen from infinity above. Large differences in the paths of the camera were seen as a function of both FOVg and ESP. Ten of the subjects were then asked to find the position for each display that minimized camera motion. The results fit well with predictions from an equation that took the ratio of human FOV (roughly 180 degrees) to FOVg times the Geometric Eye Point (GEP) of the imager: Zero Station Point = (180/FOVg)*GEP

Psotka, Joseph↗