Search NASA⌕ Search

SEARCH · Search NASA

Results for “void formation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Experimental study of void formation during aluminum solidification in reduced gravity

Void formation due to volumetric shrinkage and liquid/vapor reorientation during aluminum solidification was observed in real time by using a radiographic viewing system in normal and reduced gravity. An end-chill directional solidification furnace with water quench was designed and constructed to solidify aluminum samples during the approximately 16 sec of reduced gravity (+/-0.02g) achieved by flying an aircraft through a parabolic trajectory. In the first series of tests the aluminum was contained in a vacuum sealed, pyrolytic boron nitride crucible. An ullage space was present during each test. Void formation was recorded for two cases: a nonwetting system, and a wetting system where wetting occurred between the aluminum and the crucible lid. The void formation in the nonwetting case was similar in normal and reduced gravity, with a single vapor cavity forming at the top of the crucible. In the wetting case during reduced gravity surface tension caused two voids to form in the top corners of the crucible, but during normal gravity only one large void formed across the top. In the second series of tests the aluminum was contained in a pyrolytic boron nitride crucible that was placed in a stainless steel container and sealed in an environment of argon plus 4 percent hydrogen. An ullage space was present during each test. Void formation was recorded for two cases: a nonwetting system, and a wetting system where wetting occurred between the aluminum and one side wall and the lid. The void for nation in the nonwetting case was similar in normal and reduced gravity, with a single vapor cavity forming at the top of the crucible, although the meniscus became more convex in reduced gravity. In the wetting case the aluminum did not climb up the corners in 1g, and one large symmetric void resulted at the top when the aluminum had solidified. In the wetting case during reduced gravity the molten aluminum was drawn up the wetted wall and partially across the lid by a capillary underpressure; however, on the nonwetting wall the aluminum moved down. One void resulted along the nonwetting side of the container continuing to the top on the same side.

Chiaramonte, Francis Paul, III↗
NASA NTRS1992

An initial study of void formation during solidification of aluminum in normal and reduced-gravity

Void formation due to volumetric shrinkage during aluminum solidification was observed in real time using a radiographic viewing system in normal and reduced gravity. An end chill directional solidification furnace with water quench was developed to solidify aluminum samples during the approximately 16 seconds of reduced gravity (+/- 0.02g) achieved by flying an aircraft through a parabolic trajectory. Void formation was recorded for two cases: first a nonwetting system; and second, a wetting system where wetting occurs between the aluminum and crucible lid. The void formation in the nonwetting case is similar in normal and reduced gravity, with a single vapor cavity forming at the top of the crucible. In the wetting case in reduced gravity, surface tension causes two voids to form in the top corners of the crucible, but in normal gravity only one large voids forms across the top.

Chiaramonte, Francis P.↗
NASA NTRS1991

Mechanisms of voids formation during cooldown and freezing of lithium in SP-100 type systems

The mechanisms of void formation during the cooldown and freezing of lithium coolant within the primary loop of SP-100 type systems are investigated. These mechanisms are: (a) homogeneous nucleation, (b) heterogeneous nucleation, (c) normal segregation of helium gas dissolved in liquid lithium, and (d) shrinkage of lithium during freezing. To evaluate the void formation potential due to segregation, a numerical scheme that couples the freezing and mass diffusion processes in both the solid and liquid regions is developed. The results indicated that the formation of He bubbles is unlikely by either homogeneous or heterogeneous nucleation during the cooldown process. However, homogeneous nucleation of He bubbles following the segregation of dissolved He in liquid Lithium ahead of the solid-liquid interface is likely to occur. Results also show that total volume of He void is insignificant when compared to that of shrinkage voids.

Yang, Jae Y.↗
DOE OSTI2024

Study of Void Formation at the Lithium|Solid Electrolyte Interface

There is growing recognition of the critical role of void formation in lithium metal anodes in solid-state batteries and its impact on electrochemical performance. While experimental studies have demonstrated the challenges ensuing from void formation at the lithium metal interface with the solid electrolyte, there is a need to understand and quantify the role of intrinsic transport properties in lithium metal and the impact of external stimuli, such as temperature, pressure, and current density. Here, we develop this understanding by constructing a phase field-based model that captures the evolution of void domains at the lithium-solid electrolyte interface. Growth of the pores is driven by the fast removal of lithium from the interface during stripping at high current densities. Relative magnitudes of the bulk and surface lithium diffusivities, along with the applied current density, dictate the final pore morphology. Increasing the temperature results in faster diffusion, while external applied pressure causes creep flow of lithium, both of which help to mitigate the evolution of voids by quickly transporting metal from the bulk to the interface. Finally, a phase map as a function of temperature and pressure is developed as a guide to determine the regions that can lead to the stable cycling of lithium metal.

25 ENERGY STORAGE↗
NASA NTRS1991

An investigation of voids formation mechanisms and their effects on freeze and thaw processes of lithium and lithium fluoride

The mechanisms of void formation during the cooldown and freezing of lithium coolant within the primary loop of SP-100 type systems are investigated. These mechanisms are: (1) homogeneous nucleation; (2) heterogeneous nucleation; (3) normal segregation of helium gas dissolved in liquid lithium; and (4) shrinkage of lithium during freezing. To evaluate the void formation potential due to segregation, a numerical scheme that couples the freezing and mass diffusion processes in both the solid and liquid regions is developed. The results indicated that the formation of He bubbles is unlikely by either homogeneous or heterogeneous nucleation during the cooldown process. However, homogeneous nucleation of He bubbles following the segregation of dissolved He in liquid lithium ahead of the solid-liquid interface is likely to occur. Results also show that total volume of He void is insignificant when compared to that of shrinkage voids. In viewing this, the subsequent research focuses on the effects of shrinkage void forming during freezing of lithium on subsequent thaw processes are investigated using a numerical scheme that is based on a single (solid/liquid) cell approach. The cases of lithium-fluoride are also investigated to show the effect of larger volume shrinkage upon freezing on the freeze and thaw processes. Results show that a void forming at the wall appreciably reduces the solid-liquid interface velocity, during both freeze and thaw, and causes a substantial rise in the wall temperature during thaw. However, in the case of Li, the maximum wall temperature was much lower than the melting temperature of PWC-11, which is used as the structure material in the SP-100 system. Hence, it is included that a formation of hot spots is unlikely during the startup or restart of the SP-100 system.

El-Genk, Mohamed S.↗
DOE OSTI2021

Void formation in operator growth, entanglement, and unitarity

The structure of the Heisenberg evolution of operators plays a key role in explaining diverse processes in quantum many-body systems. In this paper, we discuss a new universal feature of operator evolution: an operator can develop a void during its evolution, where its nontrivial parts become separated by a region of identity operators. Such processes are present in both integrable and chaotic systems, and are required by unitarity. We show that void formation has important implications for unitarity of entanglement growth and generation of mutual information and multipartite entanglement. We study explicitly the probability distributions of void formation in a number of unitary circuit models, and conjecture that in a quantum chaotic system the distribution is given by the one we find in random unitary circuits, which we refer to as the random void distribution. We also show that random unitary circuits lead to the same pattern of entanglement growth for multiple intervals as in (1 + 1)-dimensional holographic CFTs after a global quench, which can be used to argue that the random void distribution leads to maximal entanglement growth.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2020

Void formation during cyclic oxidation of oxide dispersion strengthened FeCrAl alloys

Here, oxide dispersion strengthened FeCrAl alloys are considered for various high-temperature applications due to their excellent mechanical properties and oxidation resistance, but void formation is a concern for component durability. Cyclic oxidation testing was conducted on alloy MA956 and PM2000 at 1100–1200ºC for durations of up to 10,000 h and the void content was determined from optical cross-sections by image analysis. At 1100ºC, 100 h cycle, the low void concentrations measured were consistent with two competing mechanisms proposed in the literature: coalescence of process-induced nano-voids and alloy sintering. At 1200ºC using 1 h cycles, the void concentration was much higher, reaching ~3% to 6% for specimens tested to breakaway oxidation. The void growth was attributed to the high oxidation rates and the annihilation of oxidation-induced vacancies at the surface of the process-induced voids.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Interfacial Void Formation and Self-Healing in Oxide Scales on Al-containing High-Entropy Alloy

The exceptional high-temperature oxidation resistance of Al-containing high-entropy alloys (HEAs) is often attributed to the formation of a protective α-Al 2 O 3 scale. However, the dynamic, atomic-scale mechanisms governing the stability of this scale—including interfacial void formation and the often-postulated but rarely visualized “self-healing” capacity—remain poorly understood. Herein, we reveal the complex evolution of the triple-layer oxide scale on an Al 10 CoCrFeNi HEA through combined electron microscopy and diffraction study. We show that interfacial voids are an inherent consequence of the scaling process, originating from two distinct mechanisms: the Kirkendall effect at the interface between the γ-Al 2 O 3 /α-Al 2 O 3 and alloy driven by cationic diffusion imbalance and volumetric contraction due to phase transformations at the spinel/Cr 2 O 3 interface. Crucially, we provide microstructural evidence consistent with an intrinsic self-healing response. This process is driven by coupled inward diffusion of oxygen and outward diffusion of metal cations, leading to the in-situ formation of transient θ-Al 2 O 3 and spinel phases that partially fill and seal the voids. Here, these results provide atomic-scale insights into the phase evolution, defect formation, and self-repair of oxide scales in HEAs—highlighting pathways to enhance their oxidation resistance in extreme environments.

High-entropy alloy↗
NASA NTRS1991

Shrinkage void formation and its effect on freeze and thaw processes of lithium and lithium-fluoride for space applications

The effects of shrinkage void forming during freezing of lithium and lithium fluoride on subsequent thaw processes are investigated using a numerical scheme that is based on a single (solid/liquid) cell approach. Results show that a void forming at the wall appreciably reduces the solid-liquid interface velocity, during both freeze and thaw, and causes a substantial rise in the wall temperature during thaw. However, in the case of Li, the maximum wall temperature was much lower than the melting temperature of PWC-11, which is used as the structure material in the SP-100 system. Hence, it is concluded that a formation of hot spots is unlikely during the startup or restart of the SP-100 system.

Yang, Jae Y.↗
DOE OSTI2024

On the role of geometrically necessary dislocations in void formation and growth in response to shock loading conditions in wrought and additively manufactured Ta

This study investigates the role of geometrically necessary dislocations (GNDs) and microstructure on void nucleation and growth in wrought and additively manufactured (AM) tantalum subjected to high-strain rate loading. Multi-modal 3D data was collected using TriBeam tomography to calculate GND densities and their spatial relationship to voids. A microstructural comparison between the wrought and AM samples identified distinct void shapes and locations, with intragranular voids and more spherical voids frequently observed in the AM dataset. Results indicate that voids preferentially form at both high-angle grain boundaries and low-angle subgrain boundaries, the latter of which are frequently observed in the AM material. Through a radial distribution analysis of all voids in the datasets, significant GND localization to near-void-surface regions was observed in both samples. 3D crystal plasticity simulations were employed to extend the experimental observations, revealing higher void growth rates in [111] oriented grains when compared to [001] grains. The simulations also suggest that GNDs can be generated as part of the void growth process, with more GND accumulation for growth in a [111] grain than a [001] grain. These findings provide valuable insights into the links between nanoscale void nucleation, mesoscale void growth, and microstructural effects in dynamically loaded tantalum.

36 MATERIALS SCIENCE↗
NASA NTRS1993

Optical Spectroscopy of New Materials

Composites are currently used for a rapidly expanding number of applications including aircraft structures, rocket nozzles, thermal protection of spacecraft, high performance ablative surfaces, sports equipment including skis, tennis rackets and bicycles, lightweight automobile components, cutting tools, and optical-grade mirrors. Composites are formed from two or more insoluble materials to produce a material with superior properties to either component. Composites range from dispersion-hardened alloys to advanced fiber-reinforced composites. UV/VIS and FTIR spectroscopy currently is used to evaluate the bonding between the matrix and the fibers, monitor the curing process of a polymer, measure surface contamination, characterize the interphase material, monitor anion transport in polymer phases, characterize the void formation (voids must be minimized because, like cracks in a bulk material, they lead to failure), characterize the surface of the fiber component, and measure the overall optical properties for energy balances.

White, Susan M.↗
NASA NTRS1973

Diffusional creep and creep-degradation in dispersion-strengthened Ni-Cr base alloys.

Dispersoid-free regions were observed in the dispersion-strengthened alloy TD-NiCr (Ni-20 Cr-2 ThO2) after slow strain rate testing (stress rupture, creep, and fatigue) in air from 1145 to 1590 K. Formation of the dispersoid-free regions appears to be the result of diffusional creep. The net effect of creep in TD-NiCr is the degradation of the alloy to a duplex microstructure. Creep degradation of TD-NiCr is further enhanced by the formation of voids and intergranular oxidation in the dispersoid-free bands. Void formation was observed after as little as 0.13% creep deformation at 1255 K. The dispersoid-free regions apparently provide sites for void formation and oxide growth since the strength and oxidation resistance of Ni-20 Cr-2 ThO2.

Whittenberger, J. D.↗
DOE OSTI2020

ReaxFF molecular dynamics simulations of electrolyte–water systems at supercritical temperature

We have performed ReaxFF molecular dynamics simulations of alkali metal–chlorine pairs in different water densities at supercritical temperature (700 K) to elucidate the structural and dynamical properties of the system. The radial distribution function and the angular distribution function explain the inter-ionic structural and orientational arrangements of atoms during the simulation. The coordination number of water molecules in the solvation shell of ions increases with an increase in the radius of ions. We find that the self-diffusion coefficient of metal ions increases with a decrease in density under supercritical conditions due to the formation of voids within the system. The hydrogen bond dynamics has been interpreted by the residence time distribution of various ions, which shows Li+ having the highest water retaining capability. The void distribution within the system has been analyzed by using the Voronoi polyhedra algorithm providing an estimation of void formation within the system at high temperatures. We observe the formation of salt clusters of Na+ and K+ at low densities due to the loss of dielectric constants of ions. The diffusion of ions gets altered dramatically due to the formation of voids and nucleation of ions in the system.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1972

Diffusional creep and creep degradation in the dispersion-strengthened alloy TD-NiCr

Dispersoid-free regions were observed in TD-NiCr (Ni-20Cr-2ThO2) after slow strain rate testing in air from 1145 to 1590 K. Formation of the dispersoid-free regions appears to be the result of diffusional creep. The net effect of this creep is the degradation of TD-NiCr to a duplex microstructure. Degradation is further enhanced by the formation of voids and integranular oxidation in the thoria-free regions. These regions apparently provided sites for void formation and oxide growth since the strength and oxidation resistance of Ni-20Cr is much less than Ni-20Cr-2ThO2. This localized oxidation does not appear to reduce the static load bearing capacity of TD-NiCr since long stress rupture lives were observed even with heavily oxidized microstructures. But this oxidation does significantly reduce the ductility and impact resistance of the material. Dispersoid-free bands and voids were also observed for two other dispersion strengthened alloys, TD-NiCrAl and IN-853. Thus, it appears that diffusional creep is charactertistic of dispersion-strengthened alloys and can play a major role in the creep degradation of these materials.

Whittenberger, J. D.↗