The plugging performance of preformed particle gel to water flow through large opening void space conduits
Not provided.
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Not provided.
X-Ray Tomography. Porosity is commonly measured using mercury injection (MI) or water immersion porosimeter (WIP). Both MI and WIP utilize pressure to fill open voids with mercury or water respectively. A measure of the volume change of the sample is then used to estimate the percentage of open voids. However, for the purpose of rheological study it is important to get an accurate measure of open and closed voids. X-ray tomography has been selected as it offers a three-dimensional view into the sample that can quantify all pores limited only by the voxel size which is in the micron range for this study. Radiographs for tomography were collected at the Material Science and Technology Division at Los Alamos National Lab using the Carl Zeiss Xradio 520 instrument and Scout-and-Scan version 16.1 operating software. Two samples were imaged, the starting material and the deformed sample SiO2_65. 3001 radiographs were taken of the starting material with a 6 second exposure time using a 4x objective lens. The x-ray beam was set to 60 kilovoltage peak (kVp) and 5 watts. 1901 radiographs were taken of SiO2_65 with a 25 second exposure time using a 10x objective lens. The x-ray beam was set to 80 kVp and 7 watts. Radiograph files were analyzed by Brian Patterson using Avizo. Void and inclusion volumes were output by voxel sized (1.03 μm) slices, used to calculate a total percentage volume for the starting material.
Industry 4.0 is revolutionizing manufacturing through the integration of automation and real-time data sharing in cyber-physical systems. At the forefront of this revolution is large-format additive manufacturing. In large-format printing, parts are often designed to be an even number of beads wide to produce a completely dense part. However, voids can still arise. This is often due to the part not being an even number of bead widths wide in some areas, or in geometry containing acute angles, as the process of generating closed contours cannot completely fill the space. Voids can be tolerated in smaller models, but in large-format additive manufacturing they may cause mechanical defects. To fill these voids, open loop paths called skeletons are often used, but they are typically limited by the physical constraints defined in the slicing software. To address this, researchers at Oak Ridge National Laboratory have extended skeleton toolpaths via an adaptive methodology. These adaptive skeletons were found to better fill void spaces through manipulation of physical parameters of the build process and were calculated as part of the slicing process.
Li-ion cells provide an energy dense solution for systems that require rechargeable electrical power. However, these cells can undergo thermal runaway, the point at which the cell becomes thermally unstable and results in hot gas, flame, electrolyte leakage, and in some cases explosion. The heat and fire associated with this type of event is generally violent and can subsequently cause damage to the surrounding system or present a dangerous risk to the personnel nearby. The space flight environment is especially sensitive to risks particularly when it involves potential for fire within the habitable volume of the International Space Station (ISS). In larger battery packs such as Robonaut 2 (R2), numerous Li-ion cells are placed in parallel-series configurations to obtain the required stack voltage and desired run-time or to meet specific power requirements. This raises a second and less obvious concern for batteries that undergo certification for space flight use: the joining quality at the resistance spot weld of battery cells to component wires/leads and battery tabs, bus bars or other electronic components and assemblies. Resistance spot welds undergo materials evaluation, visual inspection, conductivity (resistivity) testing, destructive peel testing, and metallurgical examination in accordance with applicable NASA Process Specifications. Welded components are cross-sectioned to ensure they are free of cracks or voids open to any exterior surface. Pore and voids contained within the weld zone but not open to an exterior surface, and are not determined to have sharp notch like characteristics, shall be acceptable. Depending on requirements, some battery cells are constructed of aluminum canisters while others are constructed of steel. Process specific weld schedules must be developed and certified for each possible joining combination. The aluminum canisters' positive terminals were particularly difficult to weld due to a bi-metal strip that comes ultrasonically pre-welded by the manufacturer. This was further complicated as the maximum electrode force was limited to low-electrode force to prevent deflection of the aluminum can during welding. Other Li-ion cells are comprised of smaller diameter cylindrical steel canisters which are inherently capable of handling greater force from the electrodes. Allowing higher-electrode forces aids greatly in insuring a consistent resistance network for the weld. Overall lessons learned: developing good jigs is critical to insure the parts and electrodes are planer to one another and the location of the weld sites remains accurate and repeatable; maintaining strict control over materials is critical--materials must be of a specific hardness and chemical composition to insure that a weld schedule is repeatable; accuracy of the die used to stamp the projections is critical and worth the investment; and proper seasoning of the electrodes is critical to producing consistent welds--once the electrodes have been properly seasoned, cleaning/dressing should be avoided until it is absolutely necessary.
Ductile materials fail through mechanisms of void nucleation and coalescence. A tensile test of a ductile metal begins with reversible elastic deformation, proceeds through permanent plastic deformation, and ends with rupture. Dislocations in the grains of a metal do not slip in the elastic range but begin moving in the plastic range. As the dislocations interact with grain boundaries and each other, they cause increasing resistance to plastic deformation, termed work hardening. The applied load and the true stress rise together during this process. When the dislocations have no room to move, voids open up in the material. As these voids coalesce into cracks, the true stress rises rapidly and the sustained load decreases. Rupture occurs when the cracks propagate through the specimen and it loses all load-carrying capacity. The complexity of the ductile fracture phenomenon continues to attract substantial attention from researchers. Sharp objects in a production environment can puncture fragile components made from ductile metals. Non-linear dynamic simulations help engineers to plan processes such that these components do not fail when an accident happens. The projectile is termed a probe, and the component is the target. The surface of the probe that contacts the target may be sharp, blunt, or flat. Probes are typically cylindrical for simplicity, but other shapes that exist in the production environment are equally applicable.
Quantifying chemical compositions around nanovoids is a fundamental task for research and development of various materials. Atom probe tomography (APT) and scanning transmission electron microscopy (STEM) are currently the most suitable tools because of their ability to probe materials at the nanoscale. Both techniques have limitations, particularly APT, because of insufficient understanding of void imaging. Here, we employ a correlative APT and STEM approach to investigate the APT imaging process and reveal that voids can lead to either an increase or a decrease in local atomic densities in the APT reconstruction. Simulated APT experiments demonstrate the local density variations near voids are controlled by the unique ring structures as voids open and the different evaporation fields of the surrounding atoms. We provide a general approach for quantifying chemical segregations near voids within an APT dataset, in which the composition can be directly determined with a higher accuracy than STEM-based techniques.
The present paper reports the results of melt infiltrating 2D Tyranno SA3@ fiber woven preforms with molten CrSi2 between 1768 and 1896 K under a vacuum of 1.3 x 10-4 Pa (10-6 torr). The infiltration times varied between 1800 and 7200 s, which did not have any significant effect on the volume fraction of voids filled with the metal. Optical and scanning electron microscopy, back scattered electron imaging, energy dispersion spectroscopy and Raman spectroscopy were used to characterize the infiltrated preforms. A plot of the volume fraction of open voids infiltrated against the absolute melt infiltration temperature showed a sharp peak at 1773 K with almost complete infiltration of the voids at this temperature. The extent of silicide infiltration of the preforms dropped steeply above 1773 K with increasing melt infiltration temperature irrespective of the amount of infiltration time. Above 1805 K, the volume fraction of voids infiltrated with the melt was nearly 0%. It is demonstrated that CrSi2 did not show evidence of a reaction with the SiC fibers. The possibility that a resisting force due to contact angle hysteresis (CAH) may have influenced the diminishing amount of voids filled with increasing temperature above 1773 K was examined. The resistance force was estimated to be extremely small to be consequential. Another possibility that the CrSi2 may have decomposed into Cr(g) and Si(g) in the vacuum melt infiltration furnace appeared to be more plausible based on thermodynamic analyses. An empirical equation is proposed to calculate the amount of remaining charge left to infiltrate the preforms at the infiltration temperature. It is shown that an initial charge of 10 g would rationalize the present observations. While the decomposition of the CrSi2 appeared to mostly explain the present results, some discrepancies were observed, which were inconsistent with the decomposition model.
Tensile plastic deformation and fracture behavior of a laser powder bed fusion processed 316L stainless steel alloy was investigated in situ using high-resolution synchrotron x-ray computed microtomography (sXCT). Three different cases were studied: (1) specimen A1, near full-density with initial porosity of 0.04%, (2) specimen B1, initial lack-of-fusion (LOF) porosity of about 3% with the major axis of defects aligned nearly perpendicular to the tensile loading direction (LD), and (3) specimen B, similar to B1 but with the major axis of LOF defects aligned nearly parallel to LD. The effects of type, density, and orientation of defects in as-printed samples on plastic deformation and failure modes were studied by analyzing sXCT image sequences and quantitative defect properties. Specifically, the evolutions of porosity, size, aspect ratio, and angle of gas pores and LOF defects were characterized as a function of applied strain. Moreover, interactions between as-printed defects and deformation-induced crack propagation were investigated. The tensile behavior of specimen A1 was comparable to that of a commercial wrought plate. Furthermore, the quantitative in-situ sXCT results showed a void-growth phenomenon in A1 but without noticeable coalescence, resulting in a ductile cup-cone failure. Specimen B1 showed damage-driven brittle failure with limited plasticity due to early and rapid propagation of open voids. On the other hand, specimen B, with a similar amount of LOF defects as B1, showed deceivingly strong and ductile tensile behavior similar to A1 without any major crack propagations due to the favorable orientation relationship between LOF defects and the LD.
Growth of fully dense refractory thin films by means of physical vapor deposition (PVD) requires elevated temperatures T{sub s} to ensure sufficient adatom mobilities. Films grown with no external heating are underdense, as demonstrated by the open voids visible in cross-sectional transmission electron microscopy images and by x-ray reflectivity results; thus, the layers exhibit low nanoindentation hardness and elastic modulus values. Ion bombardment of the growing film surface is often used to enhance densification; however, the required ion energies typically extract a steep price in the form of residual rare-gas-ion-induced compressive stress. Here, the authors propose a PVD strategy for the growth of dense, hard, and stress-free refractory thin films at low temperatures; that is, with no external heating. The authors use TiN as a model ceramic materials system and employ hybrid high-power pulsed and dc magnetron co-sputtering (HIPIMS and DCMS) in Ar/N{sub 2} mixtures to grow dilute Ti{sub 1−x}Ta{sub x}N alloys on Si(001) substrates. The Ta target driven by HIPIMS serves as a pulsed source of energetic Ta{sup +}/Ta{sup 2+} metal–ions, characterized by in-situ mass and energy spectroscopy, while the Ti target operates in DCMS mode (Ta-HIPIMS/Ti-DCMS) providing a continuous flux of metal atoms to sustain a high deposition rate. Substrate bias V{sub s} is applied in synchronous with the Ta-ion portion of each HIPIMS pulse in order to provide film densification by heavy-ion irradiation (m{sub Ta} = 180.95 amu versus m{sub Ti} = 47.88 amu) while minimizing Ar{sup +} bombardment and subsequent trapping in interstitial sites. Since Ta is a film constituent, primarily residing on cation sublattice sites, film stress remains low. Dense Ti{sub 0.92}Ta{sub 0.08}N alloy films, 1.8 μm thick, grown with T{sub s} ≤ 120 °C (due to plasma heating) and synchronized bias, V{sub s} = 160 V, exhibit nanoindentation hardness H = 25.9 GPa and elastic modulus E = 497 GPa compared to 13.8 and 318 GPa for underdense Ti-HIPIMS/Ti-DCMS TiN reference layers (T{sub s} < 120 °C) grown with the same V{sub s}, and 7.8 and 248 GPa for DCMS TiN films grown with no applied bias (T{sub s} < 120 °C). Ti{sub 0.92}Ta{sub 0.08}N residual stress is low, σ = −0.7 GPa, and essentially equal to that of Ti-HIPIMS/Ti-DCMS TiN films grown with the same substrate bias.
The potential and limitations of vacuum melt infiltrating woven preforms of 2D Tyranno SA3 fibers with Cr-25(wt.%)Si alloy were investigated. Microstructural observations revealed that the volume fractions of open voids infiltrated by the molten metal varied between 3.7 and 10.0% irrespective of the magnitudes of the melt infiltration temperatures and hold times, which was attributed in part to substantial volatilization of the silicide charge based on computational thermodynamics. In the absence of experimental data, poor wettability of the melt could not be ruled out unambiguously. Other possible reasons are carefully examined and discarded. Ring microstructures were observed around the fibers mainly at the outer surfaces of the infiltrated preform, where the BN and chemical vapor infiltrated SiC coatings had vaporized in the high vacuum environment. In contrast, they were absent in the interior of the preform, where the coatings were still present with no evidence of molten metal attack of the coatings. Details of thermodynamic calculations are presented to confirm the volatilization of the BN and CVI SiC coatings thereby resulting in the ring microstructures due to the filling of voids by the molten silicide. It is concluded that successful melt infiltration of Tyranno SA3® with Cr-25%Si can be only achieved under sufficient positive pressure to prevent volatilization of the coatings and the molten silicide.
Here, we present a multi-material cell model (closure model) for demanding arbitrary Lagrangian-Eulerian (ALE) simulations of fluids and solids. It is based on the interface-aware sub-scale dynamics (IASSD) approach which utilizes the exact material interface geometry within the computational cell to calculate internal material interactions. Our formulation of the closure model also aims to improve the accuracy in low-speed impact events. Voids are used to represent ambient vacuum and internal free boundaries of the distinct materials. Void regions can close and open at contact surfaces, allowing a transition from contact physics to free motion in vacuum. The coupling of void closure and opening with a new formulation of the IASSD model for solids is tested on several one- and two-dimensional numerical examples, ranging from gas expansion in vacuum to planar and round object impacts at various speeds.
An experimental study has been undertaken to explore the convective heat transfer enhancement that can be achieved in an impinging airflow arrangement by bonding layers of graphitic foam to a heated metal substrate. The effects of foam protrusion, foam thickness and foam properties were explored in this study. The results show that surfaces with a layer of foam protruding upward with open edges had the highest convective enhancement over that of the bare substrate under the same conditions. For the protruding cases, convective enhancements of 30-70% were observed for airflows ranging from 7-11 m/s, for foam thicknesses in the range 2-10 mm. The highest enhancements were observed for foam specimens with the most open, interconnected void structure.
The present invention is premised upon an inventive method of producing an over-molded edge portion on a flexible substrate, wherein the edge portion is void of open areas due to support devices in the mold cavity.
Disclosed herein are single layer transparent coatings with an anti-reflective property, a hydrophobic property, and that are highly abrasion resistant. The single layer transparent coatings contain a plurality of oblate voids. At least 1% of the oblate voids are open to a surface of the single layer transparent coatings.
Redshift observations of 30 clusters in the direction of the Sextans-Leo supercluster candidate are reported. The observations are part of a program which involves mapping the universe's large-scale structure, and include North Galactic Cap Abell clusters, Abell clusters that have only been partially observed, and unmeasured poor Zwicky clusters. Three large superclusters are identified in the region which surround an apparent void that is open on one side towards the galaxy void in Bootes. The minimum dimensions of the void are given, and one of the superclusters is identified based on it resemblance to Coma/A1367. The emptiness of the Bootes void and the void of Bahcall and Soneira (1982) are redefined by the positions determined for five clusters observed in other portions of the northern cap. Additionally, some galaxies appear to be within the bounds of the Sextans-Leo void.
RATIONALE: A simple method to introduce unprocessed samples into a solvent for rapid characterization by liquid introduction atmospheric pressure ionization mass spectrometry has been lacking. The continuous flow, self-cleaning open port sampling interface introduced here fills this void. METHODS: The open port sampling interface used a vertically aligned, co-axial tube arrangement enabling solvent delivery to the sampling end of the device through the tubing annulus and solvent aspiration down the center tube and into the mass spectrometer ionization source via the commercial APCI emitter probe. The solvent delivery rate to the interface was set to exceed the aspiration rate creating a continuous sampling interface along with a constant, self-cleaning spillover of solvent from the top of the probe. RESULTS: Using the open port sampling interface with positive ion mode APCI and a hybrid quadrupole time of flight mass spectrometer, rapid, direct sampling and analysis possibilities are exemplified with plastics, ballpoint and felt tip ink pens, skin, and vegetable oils. These results demonstrated that the open port sampling interface could be used as a simple, versatile and self-cleaning system to rapidly introduce multiple types of unprocessed, sometimes highly concentrated and complex, samples into a solvent flow stream for subsequent ionization and analysis by mass spectrometry. The basic setup presented here could be incorporated with any self-aspirating liquid introduction ionization source (e.g., ESI, APCI, APPI, ICP, etc.) or any type of atmospheric pressure sampling ready mass spectrometer system. CONCLUSIONS: The open port sampling interface provides a means to introduce and quickly analyze unprocessed solid or liquid samples with liquid introduction atmospheric pressure ionization source without fear of sampling interface or ionization source contamination.
Extrusion deposition additive manufacturing produces parts with inherent porosity, which typically manifests as easily accessible voids between beads. This open porosity can also be accompanied by voids within the beads themselves, and both types can impact a part’s desired performance. Porosity is influenced by a variety of factors, including infill percentage, layer height, nozzle diameter, print speed, and raster orientation. While their influence on mechanical properties and porosity have been studied previously, there has been minimal work connecting print parameters to porosity and subsequently to mechanical performance. This study investigates the relationships between print parameters, volumetric porosity, and mechanical performance. In addition, this study measures both open and closed porosity through use of a helium pycnometer rather than image analysis of a cross-section. Thus, this study will identify correlations between the volumetric density of parts and the resulting mechanical performance as a function of print parameters.
Terrafore successfully demonstrated and optimized the manufacturing of capsules containing phase-changing inorganic salts. The phase change was used to store thermal energy collected from a concentrating solar-power plant as latent heat. This latent heat, in addition to sensible heat increased the energy density (energy stored per unit weight of salt) by over 50%, thus requiring 40% less salt and over 60% less capsule container. Therefore, the cost to store high-temperature thermal energy collected in a concentrating solar power plant will be reduced by almost 40% or more, as compared to conventional two-tank, sensible-only storage systems. The cost for thermal energy storage (TES) system is expected to achieve the Sun Shot goal of $\$ $15 per kWh(t). Costs associated with poor heat-transfer in phase change materials (PCM) were also eliminated. Although thermal energy storage that relies on the latent heat of fusion of PCM improves energy density by as much as 50%, upon energy discharge the salt freezes and builds on the heat transfer surfaces. Since these salts have low thermal conductivity, large heat-transfer areas, or larger conventional heat-exchangers are needed, which increases costs. By encapsulating PCM in small capsules we have increased the heat transfer area per unit volume of salt and brought the heat transfer fluid in direct contact with the capsules. These two improvements have increased the heat transfer coefficient and boosted heat transfer. The program was successful in overcoming the phenomenon of melt expansion in the capsules, which requires the creation of open volume in the capsules or shell to allow for expansion of the molten salt on melting and is heated above its melting point to 550°C. Under contract with the Department of Energy, Terrafore Inc. and Southwest Research Institute, developed innovative method(s) to economically create the open volume or void in the capsule. One method consists of using a sacrificial polymer coating as the middle layer between the salt prill and the shell material. The selected polymer decomposes at temperatures below the melting point of the salt and forms gases which escape through the pores in the capsule shell thus leaving a void in the capsule. We have demonstrated the process with a commonly used inorganic nitrate salt in a low-cost shell material that can withstand over 10,000 high-temperature thermal cycles, or a thirty-year or greater life in a solar plant. The shell used to encapsulate the salt was demonstrated to be compatible with molten salt heat transfer fluid typically used in CSP plants to temperatures up to 600 °C. The above findings have led to the concept of a cascaded arrangement. Salts with different melting points can be encapsulated using the same recipe and contained in a packed bed by cascading the salt melting at higher melting point at the top over the salt melting at lower melting point towards the bottom of the tank. This cascaded energy storage is required to effectively transfer the sensible heat collected in heat transfer fluids between the operating temperatures and utilize the latent heat of fusion in the salts inside the capsule. Mathematical models indicate that over 90% of the salts will undergo phase change by using three salts in equal proportion. The salts are selected such that the salt at the top of the tank melts at about 15°C below the high operating-temperature, and the salt at the bottom of the tank melts 15°C above the low operating-temperature. The salt in the middle of tank melts in-between the operating temperature of the heat transfer fluid. A cascaded arrangement leads to the capture of 90% of the latent-heat of fusion of salts and their sensible heats. Thus the energy density is increased by over 50% from a sensible-only, two-tank thermal energy storage. Furthermore, the Terrafore cascaded storage method requires only one tank as opposed to the two-tanks used in sensible heat storage. Since heat is transferred from the heat transfer fluid by direct contact with capsules, external heat-exchangers are not required for charging storage. Thus, the cost of the thermal storage system is reduced due to smaller containers and less salt. The optimum salt proportions, their melting temperature and the number of salts in the cascade are determined by raw materials costs and the mathematical model. We estimate the processing cost of the encapsulation to be low, where the major cost of the capsule will be the cost of the phase-change salt(s). Our economic analyses show that the cost of EPCM-TES is about $\$ $17.98 per kWh(t), which is about 40% lower than the $\$ $28.36 per kWh(t) for a two-tank sensible heat TES for a large scale CSP-TES design. Finally, additional improvements in the heat-transfer fluids, currently in development elsewhere will further improve the energy density to achieve the SunShot goal of $\$ $15 per kWh(t).