Critical Comparative Analysis of Measurement Based Centralized Online Voltage Stability Indices
Not provided.
Engineering↗
SEARCH · Search NASA
Results for “voltage indices”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Robust passivation of CdSeTe based solar cells using reactively sputtered magnesium zinc oxide
Magnesium zinc oxide (MZO, Mg x Zn 1-x O) is a leading emitter for CdTe-based solar cells due to its transparency and the ability to tune its conduction band offset with the absorber. Devices employing alloyed cadmium selenide telluride (CST, CdSe y Te 1-y ) absorbers achieved high efficiency (>19%) using MZO deposited by reactive sputtering over a broad composition range (3.68–3.92 eV, x: 0.20–0.35). Minimal differences in implied and measured open circuit voltage indicate that the contacts are well passivated and highly selective across the spectrum of MZO employed. Device performance insensitivity to MZO composition, which is not observed in CdTe devices, is attributed to the formation of an oxygenated interface layer. Se volatility creates a group VI deficiency at the interface that drives O migration from the MZO into the absorber. This introduces conductivity in the emitter not present in its as-deposited state, contributing to the exceptional performance observed. It is shown that the quality of device passivation depends on the oxidation state of the as-deposited MZO such that intelligent control and management of the reactive sputtering process is required.
36 MATERIALS SCIENCE↗
A red-emitting carborhodamine for monitoring and measuring membrane potential
Biological membrane potentials, or voltages, are a central facet of cellular life. Optical methods to visualize cellular membrane voltages with fluorescent indicators are an attractive complement to traditional electrode-based approaches, since imaging methods can be high throughput, less invasive, and provide more spatial resolution than electrodes. Recently developed fluorescent indicators for voltage largely report changes in membrane voltage by monitoring voltage-dependent fluctuations in fluorescence intensity. However, it would be useful to be able to not only monitor changes but also measure values of membrane potentials. This study discloses a fluorescent indicator which can address both. We describe the synthesis of a sulfonated tetramethyl carborhodamine fluorophore. When this carborhodamine is conjugated with an electron-rich, methoxy (-OMe) containing phenylenevinylene molecular wire, the resulting molecule, CRhOMe, is a voltage-sensitive fluorophore with red/far-red fluorescence. Using CRhOMe, changes in cellular membrane potential can be read out using fluorescence intensity or lifetime. In fluorescence intensity mode, CRhOMe tracks fast-spiking neuronal action potentials (APs) with greater signal-to-noise than state-of-the-art BeRST 1 (another voltage-sensitive fluorophore). CRhOMe can also measure values of membrane potential. The fluorescence lifetime of CRhOMe follows a single exponential decay, substantially improving the quantification of membrane potential values using fluorescence lifetime imaging microscopy (FLIM). The combination of red-shifted excitation and emission, mono-exponential decay, and high voltage sensitivity enable fast FLIM recording of APs in cardiomyocytes. The ability to both monitor and measure membrane potentials with red light using CRhOMe makes it an important approach for studying biological voltages.
59 BASIC BIOLOGICAL SCIENCES↗
2-Aminoanthracene Crystallization in Its Compatible Polystyrene Block: RAFT Synthesis and Enhanced Charge Retention in Pentacene Transistor Gate Dielectrics
We synthesized polystyrene-block-polyanthrylaminomethylstyrene (PS-b-PAAS) via RAFT reaction and side chain modification where the PAAS block is 50%. By blending 2-aminoanthracene (2AA) with PS-b-PAAS, the co-aggregation behavior of the PAAS block and 2AA within the thin film was observed by optical microscopy (OM) and x-ray diffraction. At 5 and 10 wt% of 2AA within the thin film, OM results showed a clear morphological difference between PS matrix and PS-b-PAAS matrix. Differences in the 2AA excited state lifetime in these matrices were also established using transient absorption spectroscopy (TAS). Blends were used as gate dielectrics in pentacene transistors. We compared characteristic voltage (Vc, an indicator of threshold voltage) before and after charging of PS-b-PAAS blended with unsubstituted PS and both polymers individually blended with 2AA. For blended PS-b-PAAS and PS, as the concentration of PS-b-PAAS increases, the decreased Vc especially with negative charging of the pentacene indicated a larger concentration of charge carriers induced by the dielectric film. The charging experiments also revealed that the unique structure formed by the 2AA/PS-b-PAAS blend significantly affected the charge storage capability of the organic field-effect transistors (OFET). Furthermore, this work demonstrates the novel co-aggregation structure in the dielectrics, and furthermore its impact on charge storage capability in pentacene OFETs.
36 MATERIALS SCIENCE↗
Voltage stability smart meter for analyzing voltage data and controlling an electrical power source and/or an electric appliance
Systems and methods for voltage stability monitoring and active/reactive power support are disclosed herein. In some embodiments, a smart electric meter of an end user in a grid power system can measure the voltage supplied to the end user via the grid power system, and can analyze the voltage data to detect critical voltage characteristics. The critical voltage characteristics may indicate that a voltage collapse event is likely. The smart electric meter can further estimate a voltage stability margin based on the voltage data. If necessary, the smart electric meter can control an electrical power source and/or an electric appliance positioned at or near the end user to increase the voltage stability margin.
Min, Liang↗
Voltage Stability Constrained Moving Target Defense Against Net Load Redistribution Attacks
Moving target defense (MTD) using distributed flexible AC transmission system (D-FACTS) devices is a promising defense strategy to detect stealthy false data injection (FDI) attacks against the power system state estimation. However, all existing studies myopically perturb the reactance of D-FACTS lines without considering the system voltage stability. In this paper, we first illustrate voltage instability induced by MTDs in a three-bus system. To address this issue, we further propose a novel MTD framework that explicitly considers system voltage stability by using continuation power flow and voltage stability indices. We mathematically derive the sensitivity matrix of voltage stability index to line impedance, on which an optimization problem for maximizing voltage stability index is formulated. This framework is tested on the IEEE 14-bus and the IEEE 118-bus transmission systems, in which net load redistribution attacks are launched by sophisticated attackers. Here, the simulation results show the effectiveness of the proposed framework in circumventing the voltage instability while maintaining the detection effectiveness of MTD. We conduct case studies with and without the proposed framework under different MTD planning and operational methods. The impacts of the proposed two methods on attack detection effectiveness and system economic metrics are also revealed.
24 POWER TRANSMISSION AND DISTRIBUTION↗
Electro-Optical Characterization of Arsenic-Doped CdSeTe and CdTe Solar Cell Absorbers Doped in-situ During Close Space Sublimation
Most contemporary device models predict that an acceptor concentration of at least 10^16 cm^-3 is required to reach an open circuit voltage of 1 V in polycrystalline CdTe-based solar cells. While copper has traditionally been used as the de facto p-type dopant in polycrystalline cadmium telluride (CdTe) and cadmium selenide telluride (CdSeTe), reaching high acceptor concentrations has proved to be challenging in such devices due to significant dopant compensation. The acceptor concentration in copper-doped CdTe and CdSeTe typically ranges from 10^13 to 10^15 cm^-3 and routinely exhibit low external radiative efficiencies below 0.01%, limiting their implied voltage (i.e., quasi-Fermi level splitting) to approximately 900 mV. As an alternative to copper, this work explores the use of arsenic as a p-type dopant for CdTe and CdSeTe. Using a novel technique in which a thin layer of arsenic-containing material is deposited and used as a reservoir for arsenic to diffuse into a front layer of previously undoped material, this contribution demonstrates that high external radiative efficiencies are achievable, a direct result of combined high acceptor concentrations and long minority-carrier lifetimes in the absorber. This leads to improved implied voltages, and indicates that As-doping represents a promising pathway towards improving the external voltage of CdSeTe/CdTe solar cells.
cadmium telluride↗
Integrated Cyber and Physical Anomaly Location and Classification in Power Distribution Systems
Not provided.
Automation & Control Systems↗
Broadband Characterization and Circuit Model Development of Transmission-Scale Transformers
This report describes broadband measurements of transmission-scale transformers typical in the electric power grid. This work was performed as part of the EMP Resilient Grid LDRD project at Sandia National Laboratories to generate circuit models that can be used for high-altitude electromagnetic pulse (HEMP) coupling simulations and response predictions. The objective of the work was to obtain characterization data of substation yard equipment across a frequency range relevant to HEMP. Vector network analyzer measurements up to 100 MHz were performed on two power transformers at ABB-Hitachi and a single ITEC potential transformer. Custom cable breakouts were designed to interface with the transformer terminals and provide ground connections to the chassis at the base of the transformer bushings. The three-phase terminals of the power transformers were measured as a common mode impedance using a parallel resistive splitter, and the single-phase terminals of the potential transformer were measured directly. A vector fitting algorithm was used to empirically fit circuit models to the resulting two-port networks and input impedances of the measured objects. Simplified circuit representations of the input impedances were also generated to assess the degree of precision needed for high-altitude electromagnetic pulse response predictions, which were performed in Sandia's XYCE circuit simulator platform. HEMP coupling simulations using the transformer models showed significant reduction in the voltage peak and broadening in the pulse width seen at the power transformer compared to the traveling wave voltage. This indicated the importance of the load condition when defining the coupled insult in an electric power substation. Simplified circuit models showed a similar voltage at the transformer with a smoothed waveform. The presence of potential transformers in the simulation did not significantly change the simulated voltage at the power transformer. Single-port input impedance models were also developed to define load conditions when transfer characteristics were not necessary.
24 POWER TRANSMISSION AND DISTRIBUTION↗
Oxygen Vacancy Introduction to Increase the Capacity and Voltage Retention in Li‐Excess Cathode Materials
Li‐rich rocksalt oxides are promising cathode materials for lithium‐ion batteries due to their large capacity and energy density, and their ability to use earth‐abundant elements. The excess Li in the rocksalt, needed to achieve good Li transport, reduces the theoretical transition metal redox capacity and introduces a labile oxygen state, both of which lead to increased oxygen oxidation and concomitant capacity loss with cycling. Herein, it is demonstrated that substituting the labile oxygen in Li‐rich cation‐disordered rocksalt materials with a vacancy is an effective strategy to inhibit oxygen oxidation. It is found that the oxygen vacancy in cation‐disordered lithium manganese oxide favors high Li coordination thereby reducing the concentration of unhybridized oxygen states, while increasing the theoretical Mn capacity. It is shown that in the vacancy‐containing compound, synthesized by ball milling, the Mn valence is lowered to less than +3, providing access to more than 300 mAh g −1 capacity from the Mn 2+ /Mn 4+ redox reservoir. The increased transition metal redox and decreased O oxidation are found to improve the capacity and voltage retention, indicating that oxygen vacancy creation to remove the most vulnerable oxygen ions and reduce transition metal valence provides a new opportunity for the design of high‐performance Li‐rich rocksalt cathodes.
25 ENERGY STORAGE↗
Epitaxial Sc x Al 1- x N on GaN exhibits attractive high-K dielectric properties
Epitaxial Sc x Al 1- x N thin films of ~100 nm thickness grown on metal polar GaN substrates are found to exhibit significantly enhanced relative dielectric permittivity (ε r ) values relative to AlN. ε r values of ~17–21 for Sc mole fractions of 17%–25% ( x = 0.17–0.25) measured electrically by capacitance–voltage measurements indicate that Sc x Al 1- x N has the largest relative dielectric permittivity of any existing nitride material. Since epitaxial Sc x Al 1- x N layers deposited on GaN also exhibit large polarization discontinuity, the heterojunction can exploit the in situ high-K dielectric property to extend transistor operation for power electronics and high-speed microwave applications.
36 MATERIALS SCIENCE↗
Improving Distribution System Operations Using Fleet Control of Electrolyzers
The proliferation of electrolyzers presents an opportunity for grid operators. Fast response times and the use of hydrogen as storage can be leveraged in a symbiotic way to support increasing penetration levels of photovoltaics (PV) in the distribution grid. This work presents the grid integration of an electrolyzer fleet and its control applications to minimize the impact of increasing solar PV penetration in the distribution network. The study involves a feeder model of a real utility circuit from a utility partner with an operational model of a fleet of electrolyzers. The operational improvements are quantified with performance metrics. The metrics show that the fleet control application of the electrolyzers can aid in reducing overvoltages, voltage fluctuations, and control device operations induced by intermittent solar generation. The locational dependence of electrolyzers are also discussed in terms of performance metrics.
39 EE - Hydrogen and Fuel Cell Technologies (EE-3F↗
Two-dimensional superconductivity and anisotropic transport at KTaO 3 (111) interfaces
The distinctive electronic structure found at interfaces between materials can allow unconventional quantum states to emerge. Here we report on the discovery of superconductivity in electron gases formed at interfaces between (111)-oriented KTaO 3 and insulating overlayers of either EuO or LaAlO 3 . The superconducting transition temperature, as high as 2.2 kelvin, is about one order of magnitude higher than that of the LaAlO 3 /SrTiO 3 system. Notably, similar electron gases at KTaO 3 (001) interfaces remain normal down to 25 millikelvin. The critical field and current-voltage measurements indicate that the superconductivity is two-dimensional. In EuO/KTaO 3 (111) samples, a spontaneous in-plane transport anisotropy is observed before the onset of superconductivity, suggesting the emergence of a distinct “stripe”-like phase, which is also revealed near the critical field.
75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
Analog vector-matrix multiplication by capacitive elements with resistive state storage
An array circuit includes a plurality of vector-matrix multiplication (VMM) elements arranged in rows and columns. The VMM elements are configured to collectively perform multiplication of an input vector by a programmed input matrix to generate a plurality of output values that are representative of a result matrix that is the result of multiplication of the input vector and the input matrix. The VMM elements store states of the input matrix. Input voltages to the array are representative of elements of the input vector. A VMM element draws charge from a column read line based upon charging of a capacitor in the VMM. An integrator circuit connected to the column read line outputs a voltage that is indicative of a total charge drawn from the column read line by elements connected to the read line, which voltage is further indicative of an element of a result matrix.
Agarwal, Sapan↗
Electrolyte and Cutoff Potential Effects on Cycle Life of Li4Ti5O12/LiNi0.9Mn0.1O2 Batteries for Behind-the-Meter Storage Applications
Behind-the-Meter Storage (BTMS) is a stationary battery energy storage system that is connected to the electrical distribution system on the customer's side of the utility's service meter. BTMS systems are used to store electrical energy from the grid as well as inconstant, renewable energy, such as local solar and wind generation. A successful BTMS system will allow the customer to pair their energy generation and storage to optimize electrical consumption from the grid, improving reliability and minimizing cost. For BTMS applications, batteries must be designed and optimized with different set of criteria from other leading segments of the Li-ion battery market, like transportation, due the system being stationary and proximal to the residential or commercial building it's benefitting. BTMS applications prioritize safety, cost (low/no-critical materials), reliability (20-year calendar life), and durability (10,000 cycle life), while having the ability to (minimally) compromise energy density and rate capability. Lithium titanate (Li4Ti5O12-, LTO) is a promising anode candidate for BTMS applications due to its high safety and capacity retention, while maintaining a reasonable 160 mAhg-1 reversable capacity and composition of relatively abundant materials. (1) Specifically, LTO has a high working voltage which helps to prevent Li dendrite formation, improving safety. Furthermore, LTO also has negligible lithiation-based volume change, leading to less mechanical pulverization, or loss of active material, upon cycling. For the cathode, materials with little or no Co are of high interest due to the high cost and low abundance of Co. LiMn2O4 (LMO) has been paired with LTO for BTMS applications in the past due to its safety, low cost (abundancy), and reasonably high operating voltage. (2-4) However, the low capacity of LMO limits energy density and specific energy. While not the highest priority for BTMS applications, increasing energy density will enable deployment in space constrained BTMS applications and decrease total cost. LiNi0.9Mn0.1O2 (LN-MO) is a recently developed material with promise due to its high operating voltage and relatively low price. (5) However, Ni-rich layered oxides, including LNMO, tend to struggle with capacity retention during high-voltage cycling due to mechanical pulverization, irreversible phase transitions, and unstable solid-electrolyte interphase. The study presented here focuses on building an understanding of how electrolyte solvent and varied cutoff potentials will impact the cycle life of LTO/LN-MO cells. Specifically, a comparison is provided between ethylene carbonate (EC), ethyl methyl carbonate (EMC), fluoroethylene carbonate (FEC), and Gen2 electrolyte solvents with 1M Lithium hexafluorophosphate (LiPF6) salt, cycling to two upper termination potentials, 2.6V and 2.7V. Electrochemical testing and diagnostics (e.g., differential capacity analysis, area specific impedance, constant voltage hold, and rate capability) and post-mortem characterization will be used to understand the aging behavior and failure mechanisms of the 8 cell combinations (four electrolytes and two voltage cutoffs). Cells with FEC electrolyte showed a lower initial capacity compared to cells with Gen2, EMC, and EC cycling at both voltages; however, the cells with FEC showed consistent trends in capacity retention with 2.6V and 2.7V termination potentials, while the cells with the other electrolytes showed much higher rates of capacity loss when cycling to the higher voltage. These results indicate that FEC may play a role in improving durability of high-voltage, Ni-rich electrode systems for use in high-cycle applications, such as BTMS.
electrolyte↗
Early calendar life and health prediction of silicon batteries via machine learning with uncertainty quantification
Lithium-ion batteries with silicon anodes promise high energy density but are limited by calendar lifetime. Reducing the long iteration time to obtain experimental results requires predicting calendar lifetime early in a cell's life. In this study, we demonstrate that lightweight machine learning models with feature engineering can provide calendar lifetime estimates from early electrochemical signals. After 1 month of electrochemical aging, the best models achieve 10% error in calendar-life prediction and can separate "bad" from "good" lifetime cells with a mean F1 score of 0.857. As battery systems exhibit inherent variability, four methods for uncertainty quantification are compared, and confidence intervals are demonstrated with an uncertainty of +-3.6 months in lifetime prediction. A feature importance analysis indicates that early patterns in voltage decay are the strongest indicators of calendar lifetime. Finally, this modeling approach has high error when generalizing to new electrode chemistries or testing conditions but with appropriately low confidence.
25 ENERGY STORAGE↗
Underwater plasma breakdown characteristics with respect to highly pressurized drilling applications
Deep earth drilling is a key technique to extract oil, gas, and geothermal heat from the earth. Many complex energy focusing methods have been explored as an alternative approach to reach these resources but most of them require high energy. However, by utilizing short time span liquid plasma discharges, energy focusing can be achieved within traditional drilling systems. These discharges induce a rapid expansion process and a resulting shockwave. It is believed that this focused energy will lower the required cutting force to progress through the rock. Lowering the required cutting force will allow for lower drill bit wear, quicker rate of penetration, and an overall cost savings of the project. Plasma breakdown characteristics at drilling relevant pressures, ranging from 1 to 350 atm, were studied. A resistance–capacitance circuit with an air gapped spark switch was utilized to generate pulsed plasma between the pressurized electrodes. It was found that the required breakdown voltage increases as the pressure increases. It was also found that a plasma channel formation and an associated breakdown may or may not occur between the electrodes at different pressures due to variation in required breakdown voltages. Breakdown time-lag in the dielectric medium (tap water, 780 μS cm –1 ) increased as the pressure was increased, which indicated a higher voltage drop at higher pressures (>100 atm). The plasma generated cavitation bubble with an associated shockwave occurred as pressures were increased. However, the bubble radius and the bubble duration decreased as the pressure was increased. The plasma generated shockwave speeds fall within the expected speed of sound in water. Lastly, preliminary rock cracking tests were performed on granite at high pressures (340 and 272 atm) and it was found that plasma is able to create cracks in the rock.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Anomalous Redox Features Induced by Strong Covalency in Layered NaTi 1-y V y S 2 Cathodes for Na-Ion Batteries
The rising demand for energy density of cathodes means the need to raise the voltage or capacity of cathodes. Transition metal (TM) doping has been employed to enhance the electrochemical properties in multiple aspects. The redox voltage of doped cathodes usually falls in between the voltage of undoped layered cathodes. However, in this study, we found anomalous redox features in NaTi 1-y V y S 2 . The first discharge platform potential (2.4 V) is significantly higher than that of undoped NaTiS 2 and NaVS 2 (both around 2.2 V), and the energy density is raised by 15%. We speculate that the anomalous voltage is mainly attributed to the strong hybridization in the Ti-V-S system. Ti 3+ and V 3+ undergo charge transfer and form a more stable Ti (t 2g 0 e g 0 ) and V (t 2g 3 e g 0 ) electronic configuration. Our results indicate that higher voltage of cathode materials could be achieved by strong TM-ligand covalency, and this conclusion provides possible opportunities to explore high voltage materials for future layered cathodes.
36 MATERIALS SCIENCE↗