Search NASA⌕ Search

SEARCH · Search NASA

Results for “wind tunnel experiments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Waves on Seas of Mars and Titan: Wind-Tunnel Experiments on Wind-Wave Generation in Extraterrestrial Atmospheres

The generation of waves by winds across Earth's water oceans is a topic of enduring fascination. However, the physics of the problem are rather forbidding and thus the relationships between real-world windspeed and sea state tend to be empirical. Such empirical relations are of limited utility in environments where the physical parameters are different, such as the surfaces of other planets. These environments have only recently come to oceanographers attention, with the discovery of ancient shorelines and lakes on Mars, and the prospects for and recent evidence of lakes and seas of liquid hydrocarbons on Saturn's moon Titan. We are aware of only one other published experimental wind-water tunnel study where the fluid parameters have been varied. This used artificially-generated mm-scale waves at 3.8-7.6 Hz in water, glycerol solutions (higher viscosity) and surfactant solutions (lower surface tension). Lower viscosity solutions had higher wave growth rates: surprisingly, higher surface tension led to more rapid wave growth. The liquid density was not appreciably varied, and 1 bar air was used throughout.We used the MARSWIT (Mars Wind Tunnel) operated by ASU at NASA Ames. A fiberglass tray (5 cm x 120 cm x 75 cm) was installed in the tunnel, with an approx. 1:5 ramp to prevent strong flow separation. The tray was filled to a depth of about 4 cm. Sensors were clamped to the tray itself or held by a steel and aluminium frame just above the water level. A towel was draped on the water surface at the downwind end of the tray to act as a damper to suppress wave reflection. Position-sensitive infrared (IR) reflection sensors (Sharp GP12D02) and ultrasonic rangers (Devantech DF-04) used in mobile robotics were used as water level sensors. The tray was observed with a video camera, whose output could be viewed on a monitor and recorded on VHS tape.

Lorenz, R. D.↗

Aeroelastic stability and control of an oblique wing - Wind tunnel experiments

Results are presented for wind tunnel tests of an elastic wing model to verify the theoretical predictions for the aeroelastic instability of an oblique wing. The model wing has an elliptic planform of 10 to 1 axis ratio and a symmetrical airfoil section of 7-1/2% thickness/chord ratio. The wing is of wood and as may be seen in the photographs presented, slack wires are used to limit the amplitude of unstable motions. The fuselage is mounted on bearings permitting freedom of roll, but provision is made to clamp the fuselage for some of the tests. It is found that freedom in roll increases the dynamic pressure at which aeroelastic instability first appears. With the model free in roll, the effectiveness of the ailerons in maintaining trim is not noticeably affected by passage through the speed at which the wing would become unstable if clamped.

Jones, R. T.↗

exVis and Wind Tunnel Experiment Data

exVis is a software tool created to support interactive display and analysis of data collected during wind tunnel experiments. It is a result of a continuing project to explore the use of information technology in improving the effectiveness of aeronautical design professionals. The data analysis goals are accomplished by allowing aerodynamicists to display and query data collected by new data acquisition systems and to create traditional wind tunnel plots from this data by interactively interrogating these images. Additional information is contained in the original extended abstract.

Uselton, Samuel P.↗

Progress on Gust Load Alleviation Wind Tunnel Experiment and Aeroservoelastic Model Validation for a Flexible Wing with Variable Camber Continuous Trailing Edge Flap System

This paper discusses a wind tunnel experiment of active gust load alleviation of a flexible wing which took place at University of Washington (UW) in 2019. The experiment performed under a NASA SBIR contract with Scientific Systems Company, Inc (SSCI). The objective of the experiment is to demonstrate active controls of the Variable Camber Continuous Trailing Edge Flap (VCCTEF) system for gust load alleviation and real-time drag optimization. The wind tunnel model is a 8.2% sub-scale Common Research Model (CRM) wing. The wing structure is designed to provide a substantial degree of flexibility to represent that of a modern high-aspect ratio wing. Eight active control surfaces are employed in the VCCTEF. A new gust generator system was designed and installed by UW under a sub-contract with SSCI. The first test entry started in July 2019 and ended in September 2019. During this test entry, many significant issues were found with the hardware and software. The significant issues with the servos prevented the test objective from being completed. A follow-up second test entry in 2020 is being planned. The wing system is being repaired by SSCI. This paper reports on the progress of this experimental effort and the aeroservoelastic (ASE) model validation which was conducted during the test entry.

Nguyen, Nhan↗

Investigating Tiltrotor Formation Flight via 1/48-Scale Wind Tunnel Experiment

This paper describes two small-scale wind tunnel tests conducted in the Army 7- by 10-Foot Wind Tunnel at NASA Ames Research Center. These tests featured two 1/48-scale V-22 models that were operated in a variety of simulated flight conditions including climb, descent, and level flight at various flight speeds and spatial separations. Forces and moments experienced by the trail aircraft were used to deduce the influence of the lead aircraft on the trail aircraft. Particle Image Velocimetry (PIV) data were collected to relate these forces and moments to features in the lead aircraft wake. In general, the roll moment on the trail aircraft is shown to be maximum when the aircraft are laterally offset by a full wingspan and the trail aircraft is vertically positioned so as to be in the wake of the lead aircraft. Furthermore, the roll moment is maximal when operating near 50 knots full-scale flight speed. Because the interaction persists far downstream and the vertical position of the wake is dependent on descent angle and flight speed, lateral separation has been determined to be the best means of avoiding adverse interactions between aircraft.

Romander, Ethan↗

Investigating Tiltrotor Formation Flight Via 1/48-Scale Wind Tunnel Experiment

This paper describes two small-scale wind tunnel tests conducted in the Army 7- by 10-Foot Wind Tunnel at NASA Ames Research Center. These tests featured two 1/48-scale V-22 models that were operated in a variety of simulated flight conditions including climb, descent, and level flight at various flight speeds and spatial separations. Forces and moments experienced by the trail aircraft were used to deduce the influence of the lead aircraft on the trail aircraft. Particle Image Velocimetry (PIV) data were collected to relate these forces and moments to features in the lead aircraft wake. In general, the roll moment on the trail aircraft is shown to be maximum when the aircraft are laterally offset by a full wingspan and the trail aircraft is vertically positioned so as to be in the wake of the lead aircraft. Furthermore, the roll moment is maximal when operating near 50 knots full-scale flight speed. Because the interaction persists far downstream and the vertical position of the wake is dependent on descent angle and flight speed, lateral separation has been determined to be the best means of avoiding adverse interactions between aircraft.

PIV (PARTICLE IMAGE VELOCIMETRY)↗

Martian crater dark streak lengths - Explanation from wind tunnel experiments

The mechanism determining the length of dark erosional (type-Id) streaks near craters and hills on the surface of Mars is investigated using Mariner-9 images and the results of wind-tunnel studies (Greeley et al., 1974; Iversen et al., 1975 and 1976). An empirical model of time-dependent growth of crater-wake streaks in the downwind direction involving deflation by sand-grain saltation is developed and shown to give relatively good agreement with streak growth rates observed over a 38-day period of Mariner observations and with the streak-length/crater-diameter and streak-length/crater-height ratios analyzed statistically by Lee (1984). This time-dependent mechanism is thus considered a reasonable alternative (for dark streaks) to the blocking model proposed by Lee for both bright and dark streaks. Preliminary analysis of further wind-tunnel experiments (Iversen et al., 1982) supports the blocking model of bright-streak formation.

Iversen, J. D.↗

Development of an Aeroservoelastic Model for Gust Load Alleviation of the NASA Common Research Model Wind Tunnel Experiment

As aircraft move to using composite materials as their primary structure they become lighter and more flexible as well. This presents some significant challenges in association with gust load alleviation. In this paper we develop an aeroservoelastic model for use in developing controllers that utilize distributed control surfaces for active gust load alleviation in a set of wind tunnel experiments. The model is based on an preexisting aeroelastic wing tunnel model and compares the baseline functionality to it. We also provide simple full state feedback simulations for the model.

Cramer, Nick↗

Wind Tunnel Experiment of Microjet-based Flow Control on a Multi-Element High-Lift Airfoil

A wind tunnel model was designed, manufactured, and tested to evaluate the potential of active aerodynamic flow control for multi-element airfoils. The active flow control system involves so-called microjets –small, low momentum, normal to the surface jets located near the trailing edge of the flap –for controlling the lift and improving the aerodynamic performance characteristics of airplane high-lift systems. The configuration selected for this test is the NLR7301 two-element airfoil and it was tested in the Oran W. Nicks Low-Speed Wind Tunnel at Texas A&M University at a chord Reynolds number of 2.0 million and Machnumber of 0.10. This paper presents wind tunnel results for the NLR7301 in the Flap 20 and Flap 30 configurations. The wind tunnel results include surface pressure distributions, lift and pitching moment, and flow visualizations.The results of this experiment validate the effectiveness of the microjet with regards to control of lift in the linear regime for multi-element airfoils.

ARMD↗

Comparison of vortex lattice predicted forces with wind tunnel experiments for the F-4E(CCV) airplane with a closely coupled canard

The F-4E (CCV) wind tunnel model with closely coupled canard control surfaces was analyzed by means of a version of a vortex lattice program that included the effects of nonlinear leading edge or side edge vortex lift on as many as four individual planforms. The results were compared with experimental data from wind tunnel tests of a 5% scale model tested at a Mach number M = 0.6. They indicated that a nonlinear vortex lift developed on the side edges due to tip vortices, but did not appear to develop on the leading edges within the range of angles of attack that were studied. Instead, substantial leading edge thrust was developed on the lifting surfaces. A configuration buildup illustrated the mutual interference between the wing and control surfaces. On the configuration studied, addition of the wing increased the loading on the canard, but the additional load on the canard due to adding the stabilator was small.

Gross, L. W.↗

A Wind Tunnel Experiment for Trailing Edge Circulation Control on a 6 Percent 2-D Airfoil up to Transonic Mach Numbers

A wind tunnel test was conducted on a six percent thick slightly cambered elliptical circulation control airfoil with both upper and lower surface blowing. Parametric evaluations of jet slot heights and Coanda surface shapes were conducted at mass flow coefficients (C(sub mu)) from 0.0 to 0.12. The test data was acquired in the NASA Langley Transonic Dynamics Tunnel at Mach numbers of 0.8 and 0.3 at Reynolds numbers per foot of 1.05 x 10(exp 6) and 2.43 x 10(exp 5) respectively. For the transonic condition, (Mach = 0.8 at alpha = +3 deg), it was generally found that the smaller slot and larger Coanda surface were more effective overall than other slot/Coanda surface combinations. Generally it was found at Mach = 0.3 at alpha = 6 deg that the smaller slot and smaller Coanda surface were more effective overall than other slot/Coanda surface combinations.

Alexander, Michael G.↗

On the prediction of critical flutter conditions from subcritical response data and some related wind-tunnel experience

Methods of interpreting response measurements which could be amenable to flight flutter testing procedures were studied analytically and in the wind tunnel. One suggested scheme, which requires evaluation, is an iterative technique in which derivatives obtained from subcritical response data are used to indicate the approach to flutter. A simplification of this procedure was considered by examining the manner in which a single characteristic of the subcritical response behaves in relation to variations of the density or dynamic pressure in the approach to flutter. The use of this single parameter scheme was examined for random excitation as well as for sinusoidal forcing. The feasibility of the method is illustrated by several examples and the relative merits of random and sinusoidal excitation are discussed.

Houbolt, J. C.↗

VUV shock layer radiation in an arc-jet wind tunnel experiment

Measurements were made of the radiating gas cap of a blunt body in a NASA-Ames 20 MW arc-jet wind tunnel. The test gas was air. Spectra of the flux incident on a small aperture centered at the stagnation region were obtained. A helium-cooled, magnesium fluoride window transmitted the flux into an evacuated collimating system that focused the aperture onto the entrance slit of a spectrometer. Data were obtained with films and by photomultipliers. The spectral ranges covered were the vacuum ultraviolet, VUV, (120 nm to 200 nm) and the ultraviolet to near infrared (200 nm to 900 nm) with resolutions from 0.05 nm to 0.5 nm. This paper presents the preliminary VUV results from the experiment. Results from the 200 nm to 900 nm spectral range have been presented elsewhere. Representative spectral records from 120 nm to 200 nm are shown. The intense atomic oxygen and nitrogen lines which are of concern to hypersonic flight are measured. Carbon lines are are also seen. These results will be used to help develop and validate aerothermodynamic computational models of arc-jet wind tunnel performance and help to assess the importance of VUV heating to entering spacecraft.

Craig, Roger A.↗

Design and Execution of the Hypersonic Inflatable Aerodynamic Decelerator Large-Article Wind Tunnel Experiment

The testing of 3- and 6-meter diameter Hypersonic Inflatable Aerodynamic Decelerator (HIAD) test articles was completed in the National Full-Scale Aerodynamics Complex 40 ft x 80 ft Wind Tunnel test section. Both models were stacked tori, constructed as 60 degree half-angle sphere cones. The 3-meter HIAD was tested in two configurations. The first 3-meter configuration utilized an instrumented flexible aerodynamic skin covering the inflatable aeroshell surface, while the second configuration employed a flight-like flexible thermal protection system. The 6-meter HIAD was tested in two structural configurations (with and without an aft-mounted stiffening torus near the shoulder), both utilizing an instrumented aerodynamic skin.

Cassell, Alan M.↗

Laminar-flow wind tunnel experiments

Although most of the laminar flow airfoils recently developed at the NASA Langley Research Center were intended for general aviation applications, low-drag airfoils were designed for transonic speeds and wind tunnel performance tested. The objective was to extend the technology of laminar flow to higher Mach and Reynolds numbers and to swept leading edge wings representative of transport aircraft to achieve lower drag and significantly improved operation costs. This research involves stabilizing the laminar boundary layer through geometric shaping (Natural Laminar Flow, NLF) and active control involving the removal of a portion of the laminar boundary layer (Laminar-Flow Control, LFC), either through discrete slots or perforated surface. Results show that extensive regions of laminar flow with large reductions in skin friction drag can be maintained through the application of passive NLF boundary-layer control technologies to unswept transonic wings. At even greater extent of laminar flow and reduction in the total drag level can be obtained on a swept supercritical airfoil with active boundary layer-control.

Harvey, William D.↗

Reynolds-Averaged Navier-Stokes Simulation of a 2D Circulation Control Wind Tunnel Experiment

Numerical simulations are performed using a Reynolds-averaged Navier-Stokes (RANS) flow solver for a circulation control airfoil. 2D and 3D simulation results are compared to a circulation control wind tunnel test conducted at the NASA Langley Basic Aerodynamics Research Tunnel (BART). The RANS simulations are compared to a low blowing case with a jet momentum coefficient, C(sub u), of 0:047 and a higher blowing case of 0.115. Three dimensional simulations of the model and tunnel walls show wall effects on the lift and airfoil surface pressures. These wall effects include a 4% decrease of the midspan sectional lift for the C(sub u) 0.115 blowing condition. Simulations comparing the performance of the Spalart Allmaras (SA) and Shear Stress Transport (SST) turbulence models are also made, showing the SST model compares best to the experimental data. A Rotational/Curvature Correction (RCC) to the turbulence model is also evaluated demonstrating an improvement in the CFD predictions.

Allan, Brian G.↗

Orbiter BLT Flight Experiment Wind Tunnel Simulations: Nearfield Flowfield Imaging and Surface Thermography

This paper reports a series of wind tunnel tests simulating the near-field behavior of the Space Shuttle Orbiter Boundary Layer Transition Detailed Test Objective (BLT DTO) flight experiment. Hypersonic flow over a flat plate with an attached BLT DTO-shaped trip was tested in a Mach 10 wind tunnel. The sharp-leading-edge flat plate was oriented at an angle of 20 degrees with respect to the freestream flow, resulting in post-shock edge Mach number of approximately 4. The flowfield was visualized using nitric oxide (NO) planar laser-induced fluorescence (PLIF). Flow visualizations were performed at 10 Hz using a wide-field of view and high-resolution NO PLIF system. A lower spatial resolution and smaller field of view NO PLIF system visualized the flow at 500 kHz, which was fast enough to resolve unsteady flow features. At the lowest Reynolds number studied, the flow was observed to be laminar and mostly steady. At the highest Reynolds number, flow visualizations showed streak instabilities generated immediately downstream of the trip. These instabilities transitioned to unsteady periodic and spatially irregular structures downstream. Quantitative surface heating imagery was obtained using the Temperature Sensitive Paint (TSP) technique. Comparisons between the PLIF flow visualizations and TSP heating measurements show a strong correlation between flow patterns and surface heating trends.

Danehy, Paul M.↗