Engineering topics

Al-Jassim, M. M.

Publications and source records attributed to Al-Jassim, M. M..

4 records

DOE OSTI2024

Exploring Local Ionic Motion in Perovskite Solar Cells at Nanoscale through Scanning Thermo-Ionic Microscopy

We investigate the local ionic motion in the absorber layer of perovskite solar cells using scanning thermo-ionic microscopy (STIM). STIM images of perovskite films show higher STIM amplitude at most of the grain boundaries due to higher ionic motion at those regions. The perovskite absorber layer of devices aged under blue (450 nm) light soaking shows higher amplitude in STIM signal compared to controls kept in dark storage. Such enhancement of STIM amplitude upon aging under light implies an increased concentration or diffusivity (or both) of mobile ionic species in stressed devices. Our results demonstrate the utilization of the STIM technique to assess and understand the intrinsic local ionic motion in perovskite absorbers for further advancement in device stability and functionality.

aging↗

DOE OSTI2020

Local electrical degradations of solid-state electrolyte by nm-scale operando imaging of ionic and electronic transports

We report on degradation mechanisms of solid-state electrolyte (SSE) based on insights from nm-scale ionic conduction and electronic leakage for solid-state batteries. The significantly different local degradations revealed by nm-scale ionic and electronic transport imaging demonstrate the need for this nm-scale investigation. State-of-the-art lithium-ion conductive glass ceramic (Li 2 O–Al 2 O 3 –SiO 2 –P 2 O5–TiO2-GeO2) SSE shows at least two types of degradations spatially separated within the SSE, namely: (1) ionic conduction blocking and slight electronic leaking and (2) highly electronic shunting. Degradation was significantly suppressed by application of a Li-containing polyacrylonitrile thin coating on both sides of the ceramic SSE. With this coating, the ionic conduction was not reduced by the extensive cycling; instead, it improved slightly, although accompanied by a slight increase in electronic leaking. Our nm-scale transport imaging was achieved using an atomic force microscopy (AFM)-based half-cell setup and a logarithmic-scale amplifier with current sensitivity down to the fA (10-15 A) range. This half-cell setup consisting of an AFM-probe/SSE/Li structure can distinguish the ionic from the electronic current by flipping the bias-voltage polarity. This nm-scale operando imaging opens up novel characterization of ionic and electronic transport in the field of solid-state batteries.

42 ENGINEERING↗

DOE OSTI2020

Long-lasting strong electrostatic attraction and adhesion forces of dust particles on photovoltaic modules

Photovoltaic (PV) energy-yield loss due to solar module soiling has become increasingly important as solar module deployment is now at the hundreds of gigawatts scale and continues to grow rapidly. The electrostatic attraction and adhesion force (F es ) of dust particles by the high voltages from solar panels have been reported to be 1 to 2 orders of magnitude stronger than the van der Waals and water capillary forces, which has been corroborated by observing the increase in system voltage-induced soiling rate by setting up an outdoor test. Here, we report another characteristic of F es on soiling - long-lasting or slow decay after turning off the high voltage applied to solar panels. The F es decay time varies across a wide time range of 1 to 10 h, depending on two factors: 1) whether the cell, the particle, or both were charged with high voltage before the voltages were turned off; and 2) how the cell was connected to the ground after the voltage was turned off - either connected through the power-supply electronics, directly connected to the ground, or electrically floated. The Fes decay is understood in terms of 1) net electrical charge dissipations in both particle and cell, 2) thermal disordering of dipole polarization in the module glass dielectrics, and 3) charge redistribution by the electrostatic interaction of particle and module glass. This long-lasting F es for hours can affect the solar panel soiling after sunset, and it can have an even greater effect when combined with water condensation at night.

14 SOLAR ENERGY↗

NASA NTRS1989

Fabrication of n(+)/p InP solar cells on silicon substrates

InP films were grown by MOCVD on Si GaAs substrates (as well as on InP substrates, included as controls), and were used to fabricate solar cells, using the Spitzer et al. (1987) technique. Contact to the substrate was made with Al-Ti-Pd-Ag to the Si wafers and with Au-Zn alloy to the GaAs wafers, while contract to the front was made with Cr-Au-Ag. Air mass zero efficiencies were found to be 7.1 percent for Si-substrate cells and 9.4 percent for GaAs-substrate cells.

Keavney, C. J.↗