Search NASA⌕ Search

Engineering topics

Almer, Jonathan

Publications and source records attributed to Almer, Jonathan.

At least 37 records · Page 2

In Situ Synchrotron Tensile Investigations on Ultrasonic Additive Manufactured (UAM) Zirconium

The microstructure evolution of ultrasonic additive manufactured (UAM) zirconium under room temperature uniaxial tensile straining is reported. Miniature dog-bone tensile specimens of two orientations were cut from a UAM zirconium bar for in situ synchrotron tensile tests. Wide-angle X-ray scattering (WAXS) scanning at the Advanced Photon Source (APS) at Argonne National Laboratory was used to unveil the changes in microstructure of the entire gauge regions throughout the straining. A series of WAXS data analysis methods were utilized to quantify both elastic and plastic deformation mechanisms within the strained specimens. Stress concentrations were identified during early stage of plastic deformation, which become candidate necking positions and eventually lead to failure. Fracture surface analysis implied that these stress concentration locations may be correlated to the fabrication defects, providing insightful guidance for future improvement of the UAM zirconium process.

36 MATERIALS SCIENCE↗

Revealing the chemical environment of Cr, Fe, and Ni in high temperature-ultrafine precipitate strengthened steel subjected to low fluence neutron irradiation

High-temperature ultrafine-precipitate-strengthened (HT-UPS) steel has potential applications in advanced nuclear reactors as a structural material. However, little is currently known about its response to neutron irradiation. This research provides insight into the neutron irradiation-induced physicochemical changes of the major constituents in HT-UPS steels, including Fe, Cr, and Ni, using synchrotron X-ray absorption near edge structure (XANES) and diffraction. This study is the first known investigation using XANES to characterize HT-UPS steel to analyze the evolution of the atomic level chemistry. It was found that following irradiation, nucleation, ballistic dispersion, and/or coarsening of Cr 23 C 6 precipitates occurred at very low neutron irradiation fluences, from 0.003 displacements per atom (dpa) up to 0.3 dpa, at ~600°C, which were at least an order of magnitude lower than previous studies. Calculations of the angular momentum projections, partial density of states, and the XANES spectra confirmed the experimental findings of the Cr 23 C 6 precipitate evolution. In contrast, the local atomic structure around Fe and Ni atoms demonstrated irradiation resistance.

36 MATERIALS SCIENCE↗

High-Energy X-ray Tomographic Analysis of Precursor Metal Powders (Ti-6Al-4V) Used for Additive Manufacturing

We utilized high-energy x-ray tomography to characterize Ti-6Al-4V metal powders (both as-received and recycled) used in powder-bed additive manufacturing process. The image processing workflow was developed to process and analyze large amount of data objectively by computer program. The distribution of size and shape of the metal particles as well as defect (mainly porosity) inside the particles was analyzed with the statistical representation and resolution in micrometer. The result revealed that circular-shaped porosity with various sizes could be embedded in the powder particles. These porosities could potentially be transferred to the 3D printed part and critically affect the mechanical performance of the component. The present study shows the effectiveness of characterizing metal powders using x-ray imaging techniques where sufficient number of particles can be sampled within tens of minutes with a minimum sample preparation and high accuracy. Clear structural differences in the as-received and recycled powders were delineated that helps in determining the feasibility of using the recycled powders.

36 MATERIALS SCIENCE↗

Synchrotron Imaging of Pore Formation in Li Metal Solid-State Batteries Aided by Machine Learning

High-rate capable, reversible lithium metal anodes are necessary for next generation energy storage systems. In situ tomography of Li/LLZO/Li cells is carried out to track morphological transformations in Li metal electrodes. Machine learning enables tracking the lithium metal morphology during galvanostatic cycling. Nonuniform lithium electrode kinetics are observed at both electrodes during cycling. Hot spots in lithium metal are correlated with microstructural anisotropy in LLZO. Mesoscale modeling reveals that regions with lower effective properties (transport and mechanical) are nuclei for failure. Advanced visualization combined with electrochemistry represents an important pathway toward resolving non-equilibrium effects that limit rate capabilities of solid-state batteries.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

High-energy synchrotron x-ray study of deformation-induced martensitic transformation in a neutron-irradiated Type 316 stainless steel

An unusual tensile deformation behaviour in the form of a propagating band along the sample gauge was observed in two neutron-irradiated 316 stainless steel samples during room-temperature tests, leading to a combination of high strength and high ductility. These bands were not observed in an unirradiated counterpart. With the help of in situ high-energy synchrotron x-ray diffraction, the phase-specific crystal information was tracked at different deformation levels in each sample. Post-irradiation and post-deformation samples were examined using electron microscopy to characterize various microstructural features. All samples displayed a deformation-induced martensitic phase transformation, which was identified as a second strain-hardening mechanism accompanying the dislocation hardening. The deformation-induced martensitic transformation was rationalized by the effect of applied stress on the effective martensite start temperature. The results showed that the irradiation did not alter the dislocation hardening and the martensitic transformation mechanisms, but the increased yield strength in irradiated materials facilitated the localized phase transformation at the onset of plastic deformation, in contrast to the unirradiated material which required pre-straining. The hardening effect of the martensitic transformation reduced the tendency towards necking and mitigated the loss of ductility in the irradiated material by carrying the deformation in the form of a propagating band. Despite the beneficial effect from the martensitic transformation, this study indicates that this mechanism cannot not be activated at typical operating temperatures of nuclear reactors.

36 MATERIALS SCIENCE↗

High-energy X-ray phase analysis of CMAS-infiltrated 7YSZ thermal barrier coatings: Effect of time and temperature

Calcium–magnesium–alumino-silicate (CMAS) particulates enter the aero-engine in a sandy environment, melt and infiltrate into 7 wt% yttria-stabilized zirconia (7YSZ) thermal barrier coatings (TBCs), reducing their lifetime. This leads to chemical degradation in 7YSZ accompanied by tetragonal to monoclinic phase transformation upon cooling. In this work, electron-beam physical vapor deposition coatings were infiltrated with a synthetic CMAS. Here, synchrotron X-ray diffraction measurements show that CMAS infiltration at 1250 °C has about 43% higher monoclinic phase volume fraction (PVF) at the coating surface compared to 1225 °C and remains consistently higher throughout the coating depth. Additionally, the increase in annealing time from 1 to 10 h results in a 31% higher monoclinic phase at the surface. Scanning electron microscopy revealed the presence of globular monoclinic phases corresponding spatially with the above findings. These results resolve the impact of time and temperature on CMAS infiltration kinetics which is important for mitigation.

36 MATERIALS SCIENCE↗

Perspectives on Quenching and Tempering 4340 Steel

Steels are ubiquitous due to their affordability and the landscape of useful properties that can be generated for engineering applications. But to further expand the performance envelope, one must be able to understand and control microstructure development by alloying and processing. In this paper we use multiscale, advanced characterization to better understand the structural and chemical evolution of AISI 4340 steel after quenching and tempering (Q&T), including the role of quench rate and short-time, isothermal tempering below 573 K (300 °C), with an emphasis on carbide formation. We compare the microstructure and/or property changes produced by conventional tempering to those produced by higher temperature, short-time “rapid” tempering. We underscore that no single characterization technique can fully capture the subtle microstructure changes like carbon redistribution, transition carbide and/or cementite formation, and retained austenite decomposition that occur during Q&T. Only the use of multiple techniques begins to unravel these complexities. After controlled fast or slow quenching, η transition carbides clearly exist in the microstructure, likely associated with autotempering of this high martensite start temperature (Ms) steel. Isothermal tempering below 598 K (325 °C) results in the relief of carbon supersaturation in the martensite, primarily by the formation of η transition carbides that exhibit a range of carbon levels, seemingly without substitutional element partitioning between the carbide and matrix phases. Hägg transition carbide is present between 300 °C and 325 °C. After conventional tempering at or above 598 K (325 °C) for 2 h, cementite is predominant, but small amounts of cementite are also present in other conditions, even after quenching. Previous work has indicated that silicon (Si) and substitutional elements partition between the cementite, which initially forms under paraequilibrium conditions, and the matrix. Phosphorous (P) may also be preferentially located at cementite/matrix interfaces after high temperature tempering. Slower quench rates result in greater amounts of retained austenite compared to those after fast quenching, which we attribute to increased austenite stability resulting from “autopartitioning”. Rapid, high temperature tempering is also found to diminish tempered martensite embrittlement (TME) believed to be associated with the extent of austenite decomposition, resulting in mechanical properties not attainable by conventional tempering, which may have important implications with respect to industrial heat treatment processes like induction tempering. Controlling the amount and stability of retained austenite is not only relevant to the properties of Q&T steels, but also next-generation advanced high strength steels (AHSS) with austenite/martensite mixtures.

36 MATERIALS SCIENCE↗

Tensile behavior and microstructural evolution of a Fe-25Ni-20Cr austenitic stainless steel (alloy 709) from room to elevated temperatures through in-situ synchrotron X-ray diffraction characterization and transmission electron microscopy

Uniaxial tensile tests were done on Fe-25Ni-20Cr Austenitic Stainless Steel (Alloy 709) along with in-situ synchrotron measurement at different temperatures (25 degrees C, 500 degrees C, 700 degrees C and 900 degrees C). The X-Ray diffraction data was collected in-situ in order to follow the phases present as well as to derive the dislocation density as a function of strain through peak broadening analysis based on the modified Williamson-Hall method and see how trends are affected as a function of temperature. The XRD data were complemented by TEM and STEM-EDX characterization done on the post-experiment samples to observe the deformed microstructures. Finally, the paper presents a depiction of the tensile behavior of this advanced steel by interpreting the stress-strain curves and the effect of temperature through the information gained by in-situ XRD and TEM observations as well as fractography done ex-situ on the samples tested to rupture.

36 MATERIALS SCIENCE↗

In situ synchrotron X-ray tomography of 304 stainless steels undergoing chlorine-induced stress corrosion cracking

To understand the mechanisms behind chlorine-induced stress corrosion cracking (CISCC) in 304 stainless steel, synchrotron high energy x-rays were used to perform in-situ x-ray microtomography on a pre-cracked sample under load in a corrosive simulated marine environment. The tomography scans showed the crack morphology evolving into a branching crack around the surface of the sample. Finite element analysis and stress intensity analysis are conducted to explain the observed crack branching.

304 Stainless Steel↗

Method for conducting in situ high-temperature digital image correlation with simultaneous synchrotron measurements under thermomechanical conditions

This work presents a novel method of obtaining in situ strain measurements at high temperature by simultaneous digital image correlation (DIC), which provides the total strain on the specimen surface, and synchrotron x-ray diffraction (XRD), which provides lattice strains of crystalline materials. DIC at high temperature requires specialized techniques to overcome the effects of increased blackbody radiation that would otherwise overexpose the images. The technique presented herein is unique in that it can be used with a sample enclosed in an infrared heater, remotely and simultaneously with synchrotron XRD measurements. The heater included a window for camera access, and the light of the heater lamps is used as illumination. High-temperature paint is used to apply a random speckle pattern to the sample to allow the tracking of displacements and the calculation of the DIC strains. An inexpensive blue theatrical gel filter is used to block interfering visible and infrared light at high temperatures. This technique successfully produces properly exposed images at 870 °C and is expected to perform similarly at higher temperatures. The average strains measured by DIC were validated by an analytical calculation of the theoretical strain. Simultaneous DIC and XRD strain measurements of Inconel 718 (IN718) tensile test specimens were performed under thermal and mechanical loads and evaluated. Finally, this approach uses the fact that with DIC, the total strain is measured, including plastic strain, while with XRD, only elastic strain is captured. The observed differences were discussed with respect to the effective deformation mechanisms.

47 OTHER INSTRUMENTATION↗

Elastic strain tensor of zirconium hydrides in Zr2.5%Nb pressure tubes by synchrotron X-ray diffraction

Zirconium alloys are used in fuel cladding and structural components of nuclear power plants. Hydrogen enters the Zr matrix during plant operation and precipitates as hydride particles that degrade the mechanical properties of the alloy, limiting service life. Knowledge of the stress state within hydride precipitates is important to understand stress-induced degradation mechanisms such as delayed hydride cracking, but no direct quantification has yet been reported in the literature. Here, measurements are reported of the average elastic strain tensor within δ zirconium hydride precipitates in Zr2.5%Nb pressure tube material from CANDU power plants. Complete intensity and strain pole figures for the hydride were obtained by synchrotron X-ray diffraction experiments on specimens with hydrogen contents ranging from ~100 wt p.p.m. hydrogen to nearly 100% δ-hydride. Zirconium hydride precipitates by a process involving a martensitic transformation, with two hydride variants possible from a single α-Zr grain. A synthetic model of the hydride crystallographic texture allowed the interpretation of the measured strain pole figures and quantification of the elastic strain tensor for both texture components. It was found that the two variants appear in nearly equal proportion but with different stress states, differing in the sign of the shear strain components (~±3000 µ$\epsilon$). This difference is possibly associated with the shear movement of Zr atoms during the phase transformation. This suggests that hydride clusters are composed of stacks of smaller hydrides in alternating hydride variants. Stresses were estimated from a set of rather uncertain hydride elastic constants. Overall, both variants showed compressive strains along the tube axial direction (~5000 µ$\epsilon$). For low hydrogen concentrations, the hydrides' stress tensor is dominated by compressive stresses of ~300 MPa along the axial direction, probably caused by the elongated morphology of hydride clusters along this direction, and variant-dependent shear stresses of ~±100 MPa, probably from the shear movement of the Zr atoms involved in the phase transformation.

36 MATERIALS SCIENCE↗

Effects of Alloying and Processing Modifications on Precipitation Behavior and Elevated Temperature Strength in 9% Cr Ferritic/Martensitic Steels

Two low-carbon 9-Cr ferritic-martensitic steels were designed here with the aim of decreasing M 23 C 6 and maintaining or increasing MX phase fraction. A low-carbon (LC) alloy and a low-carbon, zero-niobium (0 Nb) alloy were fabricated, their designs based upon the P92 alloy system. Solutionizing temperatures to maximize V and Nb in solution while avoiding δ-ferrite were determined to be 1170 °C for the P92 alloy and 1050 °C for LC and 0 Nb, significantly lower than predicted using ThermoCalc ® modelling. As was intended, the M 23 C 6 phase fraction was reduced for LC and 0 Nb alloys after both heat treating and aging relative to the base P92 alloy, as determined by wide angle x-ray scattering (WAXS) analysis. Dislocation density measurements from x-ray line broadening in P92 and LC suggest these alloys had more stable dislocation substructures than 0 Nb at lower temperature and shorter time aging conditions. While LC exhibited lower microhardness than P92 at room temperature, the tensile properties were comparable at 650 °C, suggesting that elevated temperature strength can be achieved with lower carbon contents. Aging studies showed that P92 had a more stable microstructure for higher temperature and longer time aging conditions. The P92 alloy also had a longer stress rupture life, implying that the M 23 C 6 precipitate contribution to thermal stability is important. Evidence of Z-phase was discovered for the LC alloy aged 10,000 h at 650 °C, corresponding to decreased strength and increased ductility. Overall, the stress rupture lives of the modified heat-treatment variations of P92 and LC compare favorably to literature values for 9% Cr steels with conventional heat treatments.

36 MATERIALS SCIENCE↗

In situ high-energy X-ray diffraction mapping of Lüders band propagation in medium-Mn transformation-induced plasticity steels

Two-dimensional distributions of microstructural characteristics of austenite (γ) around the Lüders band in medium-Mn transformation-induced plasticity (TRIP) steel were revealed by in situ high-energy X-ray diffraction. Lüders band propagation leads to significant changes in the volume fraction and lattice strains of austenite. The evolution of the lattice strain of γ-311 accords well with the true yield behavior model and is used to estimate the angle of the Lüders band front with respect to the tensile axis. The modified Williamson-Hall analysis shows that the dislocation density in austenite increased from 7 × 10 14 m -2 to 1.5 × 10 15 m -2 after Lüders band propagation. This in situ high-energy X-ray diffraction study unravels two-dimensional distribution of microstructural evolution during Lüders band propagation in medium-Mn TRIP steels.

36 MATERIALS SCIENCE↗

In-situ synchrotron X-ray study of microstructural evolution during creep deformation in Grade 91 steel

Here, creep deformation mechanism of Grade 91 steel at 650 °C was investigated in-situ via wide-angle X-ray scattering (WAXS). WAXS peak broadening and a modified Williamson-Hall analysis provided information on evolution of dislocation densities in the primary α–Fe phase, while WAXS peak shifts provided lattice strains in the α–Fe matrix, M 23 C 6 and MX precipitates. Load transfer was not evident during in-situ creep deformation, suggesting that precipitates did not significantly strengthen the matrix during creep deformation. Peak broadening results illustrated an increase in average dislocation density during primary stage creep. After onset of secondary creep, there was a decrease in dislocation density, attributed to annihilation and re-ordering of dislocations in the subgrain structure, followed by a relatively constant average dislocation density with increasing strain.

36 MATERIALS SCIENCE↗

Capturing the Competing Influence of Thermal and Mechanical Loads on the Strain of Turbine Blade Coatings via High Energy X-rays

This paper presents findings of synchrotron diffraction measurements on tubular specimens with a thermal barrier coating (TBC) system applied by electron beam physical vapor deposition (EB-PVD), having a thermally grown oxide (TGO) layer due to aging in hot air. The diffraction measurements were in situ while applying a thermal cycle with high temperature holds at 1000 °C and varying internal air cooling mass flow and mechanical load. It was observed that, during high temperature holds at 1000 °C, the TGO strain approached zero if no mechanical load or internal cooling was applied. When applying a mechanical load, the TGO in-plane strain (e22) changed to tensile and the out of plane TGO strain (e11) became compressive. The addition of internal cooling induced a thermal gradient, yielding a competing effect, driving the e22 strain to compressive and e11 strain to tensile. Quantifying TGO strain variations in response to competing factors will provide a path to controlling the TGO strain, and further improving the lifetime assessment and durability design strategies for TBC systems.

36 MATERIALS SCIENCE↗

In-situ high-energy X-ray characterization of neutron irradiated HT-UPS stainless steel under tensile deformation

Here, the tensile deformation behavior of a high-temperature, ultrafine-precipitate strengthened (HT-UPS) stainless steel was characterized in-situ with high-energy X-ray diffraction at 20 and 400 °C. The HT-UPS samples were neutron irradiated to 3 dpa at 400 °C. Significant irradiation hardening and ductility loss were observed at both temperatures. Lattice strain evolutions of the irradiated samples showed a strong linear response up to near the onset of the macroscopic yield, in contrast to the unirradiated HT-UPS which showed a pronounced non-linear behavior well below the macroscopic yield. While the room temperature diffraction elastic moduli in the longitudinal direction increased after irradiation, the 400 degrees C moduli were similar before and after irradiation. The evolution of the {200} lattice strain parallel to the loading axis (ε L {200} ) showed unique characteristics: in the plastic regime, the evolution of (ε L {200} ) after yield is temperature-dependent in the unirradiated specimens but temperature-independent in the irradiated specimens; and the value of (ε L {200} ) at the yield is an irradiation-sensitive, temperature-independent . parameter. The evolution of (ε L {200} ) corresponds well with the dislocation density evolution, and is an effective probe of the deformation-induced long-range internal stresses in the HT-UPS steel.

36 MATERIALS SCIENCE↗