Search NASA⌕ Search

Engineering topics

Almer, Jonathan

Publications and source records attributed to Almer, Jonathan.

At least 55 records · Page 3

High-energy x-ray diffraction microscopy study of deformation microstructures in neutron-irradiated polycrystalline Fe-9%Cr

In this paper, we used far-field high-energy x-ray diffraction microscopy (FF-HEDM) to measure in 3D the spatial distributions of the sizes, orientations, and residual strains of grains and subgrains formed by room-temperature tensile deformation in a neutron-irradiated (450 °C, 0.01dpa) Fe-9Cr specimen and its unirradiated counterpart. We found that neutron irradiation under this condition alone had no effect on the grain size distribution. After deformation, grains fragmented into subgrains in both unirradiated and irradiated specimens: the irradiated specimen contained a few large subgrains which co-existed with many smaller subgrains, while the unirradiated specimen contained small subgrains with a relatively uniform size distribution. Prior to deformation, the irradiated specimen had higher residual strain spread compared to its unirradiated counterpart, while after deformation to the maximum uniform elongation, the strain distributions among subgrains were similar between the unirradiated and irradiated specimens. The FF-HEDM measurements provide new insight into the effects of neutron irradiation on the mechanical response of Fe-Cr ferritic alloys.

36 MATERIALS SCIENCE↗

Role of heat treatment and build orientation in the microstructure sensitive deformation characteristics of IN718 produced via SLM additive manufacturing

The benefits of additive manufacturing have been well documented, but prior to these materials being used in critical applications, the deformation mechanisms must be properly characterized. In this work, the role of heat treatment and build orientation of selective laser melting IN718 is investigated through detailed characterization. The microstructure of this material is probed through a combination of electron microscopy to identify the precipitate structure, electron backscatter diffraction to quantify the grain-level features, and synchrotron-based X-ray microcomputed tomography to detect porosity. A high degree of porosity is observed spatially near the free surface of the part, where the contour during the build process meets the interior hatch. Further, microstructure based deformation mechanisms are explored through digital image correlation relative to the grain features after monotonic and cyclic loading and in situ high-energy X-ray diffraction to identify the lattice strain evolution in these materials. Demarcations between the behaviors of the as-built versus post-processed materials are discussed; specifically, in terms of anisotropy with respect to build direction and values of the strength properties, based on the grain morphology, coherent twin formation, and precipitate structure. In conclusion, the presence of dislocation sub-structures within the grains is observed to homogenize deformation within the as-built sample, while strain partitioning is observed during loading of the post-processed sample.

36 MATERIALS SCIENCE↗

Temperature-dependent micromechanical behavior of medium-Mn transformation-induced-plasticity steel studied by in situ synchrotron X-ray diffraction

The temperature-dependent micromechanical behavior of medium-Mn transformation-induced-plasticity (TRIP) steel with a nominal chemical composition of Fe-0.1C-10Mn-2Al (mass%) fabricated by intercritical annealing 650 ºC for 1 h after cold-rolling, was investigated using in situ high-energy X-ray diffraction (HE-XRD) with uniaxial tensile tests at temperatures of 100, 25 and -50 ºC. We find that as the deformation temperature decreases, the Luders strain decreases and more austenite transforms to martensite during Luders band propagation. The Luders bands are associated with sudden changes of lattice strain in austenite. At 100 ºC, austenite is too stable to transform to martensite, resulting in limited work-hardening capability and a relatively low strain to failure. At 25 ºC, the austenite is found to transform in bursts during applied loading. These transformations correlate with stepwise peak broadening in the austenite phase and are attributed to Portevin-Le Chatelier (PLC) band propagation. At -50 ºC, we then observe a more intense TRIP effect which suppresses PLC band formation and leads to a high ultimate tensile strength. In addition to the TRIP effect, we find that work hardening in the deformation-induced martensite phase plays an important role in the plastic stability at low temperature, by accommodating stress compatibility between grains and phases. Our studies provide the first direct experimental evidence for the existence of large stress concentrations in the austenite phase near the Luders band propagation front. These observations help to deepen understanding of the complex temperature-dependent micromechanical behaviors of advanced medium-Mn TRIP steels.

36 MATERIALS SCIENCE↗

Far-Field High-Energy Diffraction Microscopy: A Non-Destructive Tool for Characterizing the Microstructure and Micromechanical State of Polycrystalline Materials

A suite of non-destructive, three-dimensional X-ray microscopy techniques have recently been developed and used to characterize the microstructures of polycrystalline materials. These techniques utilize high-energy synchrotron radiation and include near-field and far-field diffraction microscopy (NF- and FF-HEDM, respectively) and absorption tomography. Several compatible sample environments have also been developed, enabling a wide range of 3D studies of material evolution. In this article, the FF-HEDM technique is described in detail, including its implementation at the 1-ID beamline of the Advanced Photon Source. Examples of how the information obtained from FF-HEDM can be used to deepen our understanding of structure-property-processing relationships in selected materials are presented.

36 MATERIALS SCIENCE↗

Non-Destructive Characterization of Engineering Materials Using High-Energy X-rays at the Advanced Photon Source

High energy X-rays can penetrate large components and samples made from engineering alloys. Brilliant synchrotron sources like the Advanced Photon Source (APS) combined with unique experimental setups are increasingly allowing scientists and engineers to non-destructively characterize the state of materials across a range of length scales. In this article, some of the new developments at the APS, namely the high energy diffraction microscopy technique for grain-by-grain maps and aperture-based techniques for aggregate maps, are described.

36 MATERIALS SCIENCE↗

Temperature effect of elastic anisotropy and internal strain development in advanced nanostructured alloys: An in-situ synchrotron X-ray investigation

Nanostructured ferritic alloys (NFAs) are a promising structural material for advanced nuclear systems due to their exceptional radiation tolerance and high-temperature mechanical properties. Their remarkable properties result from the ultrafine ultrahigh density Y-Ti-O nanoclusters dispersed within the ferritic matrix. In this work, we performed in-situ synchrotron X-ray diffraction tests to study the tensile deformation process of the three types of NFAs: 9YWTV, 14YWT-sm13, and 14YWT-sm170 at both room temperature and elevated temperatures. A technique was developed, combining Kroner’s model and X-ray measurement, to determine the intrinsic monocrystal elastic-stiffness constants, and polycrystal Young’s modulus and Poisson’s ratio of the NFAs. Temperature dependence of elastic anisotropy was observed in the NFAs. An analysis of intergranular strain and strengthening factors determined that 14YWT-sm13 had a higher resistance to temperature softening compared to 9YWTV, attributed to the more effective nanoparticle strengthening during high-temperature mechanical loading.

Gan, Yingye↗

In situ synchrotron investigation of grain growth behavior of nano-grained UO 2

Here, we report on the study of grain growth kinetics in nano-grained UO 2 samples. Dense nano-grained UO 2 samples with well-controlled stoichiometry and grain size were fabricated using the spark plasma sintering technique. To determine the grain growth kinetics at elevated temperatures, a synchrotron wide-angle X-ray scattering (WAXS) study was performed in situ to measure the real-time grain size evolution based on the modified Williamson-Hall analysis. The unique grain growth kinetics of nanocrystalline UO 2 at 730 °C and 820 °C were observed and explained by the difference in mobility of various grain boundaries.

36 MATERIALS SCIENCE↗

Real-time phase evolution of Selective Laser Melted (SLM) Inconel 718 with temperature through synchrotron X-rays

Selective laser melting (SLM) is an additive manufacturing process that uses laser scanning to achieve melting and solidification of a metal powder bed. This process, when applied to develop high temperature material systems, holds great promise for more efficient manufacturing of turbine components that withstand extreme temperatures, heat fluxes, and high mechanical stresses associated with engine environments. These extreme operational conditions demand stringent tolerances and an understanding of the material evolution under thermal loading. This work presents a real-time approach to elucidating the evolution of precipitate phases in SLM Inconel 718 (IN718) under high temperatures using high-energy synchrotron x-ray diffraction. Four representative samples (taken along variable build height) were studied in room temperature conditions. Two samples were studied as-processed (samples 1 and 4) and two samples after different thermal treatments (samples 2 and 3). The as-processed samples were found to contain greater amounts of weakening phase, δ. Precipitation hardening of Sample 2 reduced the detectable volume of δ, while also promoting growth of γ00 in the γ matrix. Inversely, solution treatment of Sample 3 produced an overall decrease in precipitate phases. High-temperature, in-situ synchrotron scans during ramp-up, hold, and cool down of two different thermal cycles show the development of precipitate phases. Sample 1 was held at 870°C and subsequently ramped up to 1100°C, during which the high temperature instability of strengthening precipitate, γ00, was seen. γ00 dissolution occurred after 15 minutes at 870°C and was followed by an increase of δ-phase. Sample 4 was held at 800°C and exhibited growth of γ00 after 20 minutes at this temperature. These experiments use in-situ observations to understand the intrinsic thermal effect of the SLM process and the use of heat treatment to manipulate the phase composition of SLM IN718.

Sarley, Brooke A.↗

In situ high-energy X-ray diffraction study of tensile deformation of neutron-irradiated polycrystalline Fe-9%Cr alloy

The effect of neutron irradiation on tensile deformation of a Fe-9wt.%Cr alloy was investigated using in situ high-energy synchrotron X-ray diffraction during room-temperature uniaxial tensile tests. New insights into the deformation mechanisms were obtained through the measurements of lattice strain evolution and the analysis of diffraction peak broadening using the modified Williamson-Hall method. Two neutron-irradiated specimens, one irradiated at 300 °C to 0.01 dpa and the other at 450 °C to 0.01dpa, were tested along with an unirradiated specimen. The macroscopic stress–strain curves of the irradiated specimens showed increased strength, reduced ductility and work-hardening exponent compared to the unirradiated specimen. The evolutions of the lattice strain, the dislocation density and the coherent scattering domain size in the deformation process revealed different roles of the submicroscopic defects in the 300°C/0.01 dpa specimen and the TEM-visible nanometer-sized dislocation loops in the 450°C/0.01 dpa specimen: submicroscopic defects extended the linear work hardening stage (stage II) to a higher strain, while irradiation-induced dislocation loops were more effective in dislocation pinning. Lastly, while the work hardening rate of stage II was unaffected by irradiation, significant dynamic recovery in stage III in the irradiated specimens led to the early onset of necking without stage IV as observed in the unirradiated specimen.

36 MATERIALS SCIENCE↗

Crystal Plasticity Model Validation Using Combined High-Energy Diffraction Microscopy Data for a Ti-7Al Specimen

High-Energy Diffraction Microscopy (HEDM) is a 3-d x-ray characterization method that is uniquely suited to measuring the evolving micromechanical state and microstructure of polycrystalline materials during in situ processing. The near-field and far-field configurations provide complementary information; orientation maps computed from the near-field measurements provide grain morphologies, while the high angular resolution of the far-field measurements provide intergranular strain tensors. The ability to measure these data during deformation in situ makes HEDM an ideal tool for validating micro-mechanical deformation models that make their predictions at the scale of individual grains. Crystal Plasticity Finite Element Models (CPFEM) are one such class of micro-mechanical models. While there have been extensive studies validating homogenized CPFEM response at a macroscopic level, a lack of detailed data measured at the level of the microstructure has hindered more stringent model validation efforts. Here, we utilize an HEDM dataset from an alphatitanium alloy (Ti-7Al), collected at the Advanced Photon Source, Argonne National Laboratory, under in situ tensile deformation. The initial microstructure of the central slab of the gage section, measured via near-field HEDM, is used to inform a CPFEM model. The predicted intergranular stresses for 39 internal grains are then directly compared to data from 4 far-field measurements taken between ~4% and ~80% of the macroscopic yield strength. In conclusion, the intergranular stresses from the CPFEM model and far-field HEDM measurements up to incipient yield are shown to be in good agreement, and implications for application of such an integrated computational/experimental approach to phenomena such as fatigue and crack propagation is discussed.

36 MATERIALS SCIENCE↗

3D Study of Neutron Irradiation Effects on Tensile Deformation in Fe-based Alloys using High Energy Synchrotron X-rays

Recent development of 3D synchrotron X-ray techniques offers new opportunities for the investigation of nuclear materials. In this study, we use the high energy Xray diffraction microscopy (HEDM), also known as 3DXRD, to investigate the effects of neutron irradiation on microstructural response during tensile deformation in a Fe- 9%Cr alloy. Fe-9Cr has been studied extensively in experiments and modelling as a ferritic model alloy for its response to neutron irradiation. It is found that irradiation-induced hardening and reduction of ductility are significant even at very low doses, and the primary deformation mechanism is channeling. Different from earlier studies, here we focus on grain-level responses to deformation and aim to elucidate the effect of irradiation by employing the far-field HEDM setup (FF-HEDM) to obtain strains, crystallographic orientations, and centers of masses of hundreds of grains in undeformed and deformed states, providing rich 3D information well beyond the TEM and traditional diffraction measurements. It offers a deeper understanding of the structure-property relationship in nuclear materials. (authors)

36 MATERIALS SCIENCE↗

In-Situ High Energy X-ray Characterization of Tensile Deformation of Advanced Austenitic Stainless Steels

A deep understanding of the deformation mechanisms for next-generation structural materials of advanced nuclear reactors is critical to their successful applications. For this purpose, high energy synchrotron X-ray characterization techniques in combination with in situ thermo-mechanical loading have distinctive advantages in correlating the mechanical responses of the specimens with their microstructure evolution in real time. In this study, this method is employed to compare the deformation characteristics of two advanced austenitic stainless steels, NF709 steel a High-Temperature Ultrafine-Precipitate Strengthened (HT-UPS) steel, with a traditional 316 austenitic stainless steel (SS). The NF709 and HT-UPS steels are both promising candidates for next generation nuclear energy systems. The NF709 is a 20Cr-25Ni austenitic stainless steel stabilized with Nb/Ti(C,N) precipitates and possesses excellent high temperature and corrosion resistance. The HT-UPS steel (Fe-14Cr-16Ni-Ti,Nb,V) also has much improved creep resistance and high temperature performance than 316SS through the careful control of minor alloying elements to form creep resistant precipitates. While both have shown improved mechanical properties over 316SS, their deformation characteristics and underlying mechanisms are yet to be fully explored. The recent applications of simultaneous Wide-Angle X-ray Scattering (WAXS) and Small-Angle X-ray Scattering (SAXS) techniques under thermo-mechanical loading of steel samples have revealed valuable insights of the microstructural evolution during deformation. This work is to apply these techniques to characterize the deformation behaviors and also understand their relationship with the microstructures of advanced austenitic stainless steels. (authors)

36 MATERIALS SCIENCE↗

Effect of water on nanomechanics of bone is different between tension and compression

Water, an important constituent in bone, resides in different compartments in bone matrix and may impose significant effects on its bulk mechanical properties. However, a clear understanding of the mechanistic role of water in toughening bone is yet to emerge. To address this issue, this study used a progressive loading protocol, coupled with measurements of in situ mineral and collagen fibril deformations using synchrotron X-ray diffraction techniques. Using this unique approach, the contribution of water to the ultrastructural behavior of bone was examined by testing bone specimens in different loading modes (tension and compression) and hydration states (wet and dehydrated). The results indicated that the effect of water on the mechanical behavior of mineral and collagen phases at the ultrastructural level was loading mode dependent and correlated with the bulk behavior of bone. Tensile loading elicited a transitional drop followed by an increase in load bearing by the mineral phase at the ultrastructural level, which was correlated with a strain hardening behavior of bone at the bulk level. Compression loading caused a continuous loss of load bearing by the mineral phase, which was reflected at the bulk level as a strain softening behavior. In addition, viscous strain relaxation and pre-strain reduction were observed in the mineral phase in the presence of water. Taken together, the results of this study suggest that water dictates the bulk behavior of bone by altering the interaction between mineral crystals and their surrounding matrix.

Samuel, Jitin (ORCID:0000000195203350)↗

In situ synchrotron tensile investigations on 14YWT, MA957, and 9-Cr ODS alloys

Advanced ODS alloys provide exceptional radiation tolerance and high-temperature mechanical properties when compared to traditional ferritic and ferritic/martensitic 9F/M) steels. Their remarkable properties result from ultrahigh density and ultrafine size of Y-Ti-O nanoclusters within the ferritic matrix. In this work, we applied a high-energy synchrotron radiation X-ray to study the deformation process of three advanced ODS materials including 14YWT, MA957, and 9-Cr ODS steel. Only the relatively large nanoparticles in the 9-Cr ODS were observed in the synchrotron X-ray diffraction. The nanoclusters in both 14YWT and MA957 were invisible in the measurement due to their non-stoichiometric nature. Due to the different sizes of nanoparticles and nanoclusters in the materials, the Orowan looping was considered to be the major strengthening mechanism in the 9-Cr ODS, while the dispersed-barrier-hardening is dominant strengthening mechanism in both 14YWT and MA957, This analysis was inferred from the different build-up rates of dislocation density when plastic deformation was initiated. Finally, the dislocation densities interpreted from the X-ray measurements were successfully modeled using the Bergstrom's dislocation models. (C) 2016 Elsevier B.V. All rights reserved.

Lin, Jun-Li↗

Microstructural processes in irradiated materials

This is an editorial article (preface) for the publication of symposium papers in the Journal of Nuclear materials: These proceedings contain the papers presented at two symposia, the Microstructural Processes in Irradiated Materials (MPIM) and Characterization of Nuclear Reactor Materials and Components with Neutron and Synchrotron Radiation, held in the TMS 2015, 144th Annual Meeting & Exhibition at Walt Disney World, Orlando, Florida, USA on March 15–19, 2015.

irradiation effect↗

Combined near- and far-field high-energy diffraction microscopy dataset for Ti-7Al tensile specimen elastically loaded in situ

High-energy diffraction microscopy (HEDM) constitutes a suite of combined X-ray characterization methods, which hold the unique advantage of illuminating the microstructure and micromechanical state of a material during concurrent in situ mechanical deformation. The data generated from HEDM experiments provides a heretofore unrealized opportunity to validate meso-scale modeling techniques, such as crystal plasticity finite element modeling (CPFEM), by explicitly testing the accuracy of these models at the length scales where the models predict their response. Combining HEDM methods with in situ loading under known and controlled boundary conditions represents a significant challenge, inspiring the recent development of a new high-precision rotation and axial motion system for simultaneously rotating and axially loading a sample. In this paper, we describe the initial HEDM dataset collected using this hardware on an alpha-titanium alloy (Ti-7Al) under in situ tensile deformation at the Advanced Photon Source, Argonne National Laboratory. We present both near-field HEDM data that maps out the grain morphology and intragranular crystallographic orientations and far-field HEDM data that provides the grain centroid, grain average crystallographic orientation, and grain average elastic strain tensor for each grain. Finally, we provide a finite element mesh that can be utilized to simulate deformation in the volume of this Ti-7Al specimen.

36 MATERIALS SCIENCE↗