Search NASA⌕ Search

Engineering topics

Anderoglu, Osman

Publications and source records attributed to Anderoglu, Osman.

7 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

The influence of thermomechanical treatment pathways on texture and mechanical properties in ARB Cu/Nb nanolaminates

Accumulative roll-bonded Cu/Nb nanolaminates (ARB Cu/Nb) possess high strength, thermal stability, and radiation tolerance arising from a high content of heterophase interfaces at fine layer thicknesses. These properties can be tailored by processing parameters used in the ARB Cu/Nb fabrication process, in which layer thickness, thermal history, and strain pathway determine the interface types and resultant properties found in the material. In this work, we subject ARB Cu/Nb to annealing, and then two different rolling pathways – one where rolling direction is held constant (longitudinal rolling, or LR), and one where rolling direction is rotated by 90º and held constant thereafter (cross rolling, or CR). Rolling is performed on ARB Cu/Nb over a targeted range of layer thicknesses from 193 to 25 nm and resultant bulk textures measured by neutron diffraction are correlated with mechanical properties measured by miniaturized tensile tests. The annealing procedure sharpens texture in both phases. We find that Cu mostly develops the same texture in LR and CR. In contrast, Nb develops a distinct texture along the CR pathway that is distinct from the LR texture. The composite texture of Cu/Nb is thus distinct between LR and CR pathways. This difference in texture development between Cu and Nb as a function of strain after change in rolling direction demonstrates the viability for deliberate pairing of Cu LR and Nb CR textures at a desired layer thickness. For mechanical properties, we find that differences in texture do not result in yield or flow stress differences above a layer thickness of 25 nm. Below a layer thickness of 25 nm, despite similar Taylor factors, yield and flow stress and are significantly different. In conclusion, this indicates texture only influences mechanical behavior at low layer thickness, where interface structure dominates mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Nanostructured Composite Alloys for Extreme Environments

Accumulative Roll Bonding was used to process nanolayered Cu/Nb and Zr/Nb composites with varying individual layer thickness. Mechanical tests show remarkable strength as the average layer thickness decreases. Relatively high strength is preserved even at elevated temperatures. Despite differences in texture between rolling paths (longitudinally rolled-RL and cross rolled-CR) Cu/Nb, flow stresses between the resultant materials were similar. In addition, thermal conductivity does not change significantly as the interface density increases. The alloys show remarkable resistance to irradiation damage at very high doses due to stability of the interfaces. The results on Zr/Nb indicate that liquid phase chemistry resulting from thermal spikes play an important role and should be taken into account when designing alloys for extreme environments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Development of Conceptual Lead Cartridge Design to Perform Irradiation Experiments in VTR

This paper seeks to introduce the latest design of the Extended Length Test Assembly–Cartridge Lead (ELTA-CL) with associated thermal-hydraulic (TH) assessment and related experiment activities to support the critical component development performed by the ELTA-CL team (Los Alamos National Laboratory, Westinghouse Electric Company, and the University of New Mexico). The goal of the ELTA-CL program is to develop and validate an experimental capability to perform irradiation experiments in the Versatile Test Reactor (VTR) addressing Lead Fast Reactor (LFR) technology gaps, in support of the commercial development of advanced lead-cooled fast reactor concepts. Through a design maturation process and parametric study, a conceptual design is proposed to meet the requirements for material and corrosion testing. Thermal-hydraulic characteristics for the conceptual design at desired operating conditions are assessed with systems-level (one-dimensional) and computational fluid dynamics (three-dimensional) simulations. Along with the conceptual design work, experimental activities for the development of critical components such as the pump and flowmeter are undertaken. From both the modeling study and the experimental results, the design requirements of the Phase 1 ELTA-CL (e.g., 500°C and 2 m/s) are achievable with the current conceptual design. Additional design improvements and safety assessments at both steady-state and transient conditions for the final ELTA-CL design will be pursued.

42 ENGINEERING↗
DOE OSTI2021

Layer dissolution in accumulative roll bonded bulk Zr/Nb multilayers under heavy-ion irradiation

In this work, the heavy-ion irradiation behavior of bulk zirconium-niobium multilayered composites was investigated up to large doses. Multilayers with an average individual layer thicknesses ranging between 15 and 80 nm were synthesized by accumulative roll bonding technique. The irradiation was performed with a defocused 7 MeV Zr 2+ ion beam at 500 °C. The maximum dose achieved was ~145 dpa at the depth of ~1.5 μm from the irradiated surface. Sub-surface microstructural damage and the chemical redistribution were characterized by transmission electron microscopy and energy dispersive spectroscopy, respectively. Irrespective of the layer thicknesses, the irradiation condition caused layer instability and the extent of damage varied with the dose levels. Doses lesser than ~60 dpa caused layer fragmentation and greater than ~60 dpa resulted in layer dissolution. The chemical mixing of layers occur to a depth of ~1 μm, consuming multiple bi-layer periods. Despite the elevated irradiation temperature (500 °C) and a slightly positive heat of mixing (+6 kJ/mol), no phase separation was observed and single-phase was retained in the mixed region. The results demonstrate that chemical mixing was facilitated by the liquid phase miscibility of Zr and Nb, which propelled the interdiffusion within the thermal spikes towards mixing.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Method of information entropy for convergence assessment of molecular dynamics simulations

The lack of a reliable method to evaluate the convergence of molecular dynamics simulations has contributed to discrepancies in different areas of molecular dynamics. Here, the method of information entropy is introduced to molecular dynamics for stationarity assessment. The Shannon information entropy formalism is used to monitor the convergence of the atom motion to a steady state in a continuous spatial domain and is also used to assess the stationarity of calculated multidimensional fields such as the temperature field in a discrete spatial domain. It is demonstrated in this work that monitoring the information entropy of the atom position matrix provides a clear indicator of reaching steady state in radiation damage simulations, non-equilibrium molecular dynamics thermal conductivity computations, and simulations of Poiseuille and Couette flow in nanochannels. A main advantage of the present technique is that it is non-local and relies on fundamental quantities available in all molecular dynamics simulations. Unlike monitoring average temperature, the technique is applicable to simulations that conserve total energy such as reverse non-equilibrium molecular dynamics thermal conductivity computations and to simulations where energy dissipates through a boundary as in radiation damage simulations. The method is applied to simulations of iron using the Tersoff/ZBL splined potential, silicon using the Stillinger–Weber potential, and to Lennard–Jones fluid. Its applicability to both solids and fluids shows that the technique has potential for generalization to other areas in molecular dynamics.

74 ATOMIC AND MOLECULAR PHYSICS↗