Search NASA⌕ Search

Engineering topics

Bei, Hongbin

Publications and source records attributed to Bei, Hongbin.

188 records · Page 11

Shear Fracture of Bulk Metallic Glasses with Controlled Applied Normal Stresses

Bulk metallic glasses (BMGs) often deform by the formation of localized shear bands which is followed by sudden shear fracture. This fracture behavior has been found to depend on not only the shear stress but also the stress normal to the shear plane, and the Mohr-Coulomb criterion has been applied to characterize shear fracture of BMGs. However, systematic verification of its applicability is non-existent because of the inability of controlling the normal to shear stress ratio on the fracture plane in the existing tests performed on BMGs. Here, we use a unique test fixture that is capable of controlling (i) the location of shear fracture and (ii) the normal to shear stress ratio on the fracture plane to perform tests on BMGs to verify the applicability of the Mohr-Coulomb criterion.

36 MATERIALS SCIENCE↗

A different type of indentation size effect

Pop-in during nanoindentation, which indicates the onset of dislocation plasticity, was systematically investigated in annealed and pre-strained single crystals of nickel using spherical indenters with different tip radii. As the indenter radius and pre-strain decrease, the maximum shear stresses determined from the pop-in loads increase. This represents a new type of indentation size effect (ISE), based not on the measured hardness as in conventional ISE, but on the stress needed to initiate dislocation plasticity.

36 MATERIALS SCIENCE↗

Oxygen effects on plastic deformation of a Zr-based bulk metallic glass

Starting with Zr of two different purities, Zr-based bulk metallic glasses (BMGs) with a nominal composition of Zr{sub 62}Cu{sub 15.5}Ni{sub 12.5}Al{sub 10} were prepared having oxygen concentrations of about 3900 and 920 at. ppm, respectively. Uniaxial compression tests showed that the BMG containing the higher level of oxygen has a higher yield strength and is capable of undergoing much less plastic deformation than that containing the lower level of oxygen. It appears that oxygen suppresses the formation of multiple shear bands but leads to an inability to sustain shear-band propagation, thus, changing the failure mode from relatively ductile to catastrophic brittle fracture.

36 MATERIALS SCIENCE↗

Spatially resolved strain measurements in Mo-alloy micropillars by differential aperture x-ray microscopy.

Spatially resolved strain distributions in the NiAl matrix and the {approx}550-1000 nm Mo fibers of a NiAl-Mo eutectic were investigated by microbeam x-ray diffraction. Position sensitive d-spacings for the individual phases were obtained from spatially resolved and energy-resolved Laue patterns. For embedded Mo fibers, the measured elastic strain is consistent with the predicted thermal mismatch strain between the NiAl and Mo phases. However, when the NiAl matrix is etched back to expose Mo micropillars, the d-spacing increases to that of unconstrained Mo, indicating release of the compressive residual strain in the Mo fibers.

36 MATERIALS SCIENCE↗

Improvement of magnetic properties of an Fe-6.5wt%Si by directional recrystallization

We report that magnetic properties of an Fe-6.5 wt. % Si alloy can be improved through texture control by using directional recrystallization. Columnar grain structures with column sizes of {approx}0.38 x 1.2 mm{sup 2} were developed during directional recrystallization. It was found that there are low energy boundaries between columns and main textures of the specimen were {l_brace}110{r_brace}<111> and {l_brace}111{r_brace}<110>. As a result, the coercivity of a directionally recrystallized specimen is reduced by a factor of 5 when measured along 60{sup o} away from the growth direction, as compared to a specimen consisting of {approx}77 {micro}m equiaxed grains.

36 MATERIALS SCIENCE↗

Strength Differences Arising from Homogeneous Versus Heterogeneous Dislocation Nucleation

We show that it is possible to distinguish between homogeneous and heterogeneous dislocation nucleation on the basis of differences in experimentally measured theoretical strengths. From nanoindentation tests, the critical shear stress for dislocation nucleation in two different Mo-alloy single crystals (Mo-3Nb and Mo-10Al-4Ni) is found to be ~1/8 of the shear modulus. The corresponding stress in uniaxially compressed Mo-10Al-4Ni micropillars is ~1/26 of the shear modulus. This strength difference is due to the higher critical stress required to nucleate a full dislocation loop homogeneously in the bulk as opposed to a half or quarter loop heterogeneously at a surface or edge.

36 MATERIALS SCIENCE↗

Small-scale mechanical behavior of intermetallics and their composites

To model and predict the mechanical behavior of composite materials, knowledge of the properties of their constituent phases as well as how they interact with each other is required. Although these mechanical properties can sometimes be deduced from measurements on bulk specimens, it is not always possible due to difficulties in producing bulk materials with compositions and structures similar to those of the individual phases in the composite. In such cases, in situ measurements of mechanical properties are needed. We review here our recent work on the application of nanoindentation and neutron diffraction to investigate the in situ mechanical responses of Cr-Cr{sub 3}Si and NiAl-Mo, two model eutectic composites that were chosen because they can be processed by directional solidification to yield well-aligned lamellar and fibrous microstructures. Phase-specific mechanical properties were measured and correlated with bulk behavior. We will discuss recently developed techniques that improve the accuracy of mechanical property measurements at small microstructural length scales.

36 MATERIALS SCIENCE↗

Development of Alumina-Forming Austenitic Stainless Steels

Work in fiscal year 2008 focused on the development of creep-resistant, alumina-forming austenitic (AFA) stainless steel alloys, which exhibit a unique combination of an excellent oxidation resistance via protective alumina (Al2O3) scale formation and high-temperature creep strength through the formation of stable nano-scale MC carbides [1-8]. High levels of Nb additions (> 1 wt.% Nb) and/or Ni additions (25-30 wt.%), at Al levels of 2.5-4 wt.%, were found to correlate with increased upper-temperature limit for Al2O3 scale formation in air ( 900 aC) and air with 10% water vapor ( 800 aC). Creep resistance also showed a strong dependence on the level of Nb additions, and was correlated with volume fraction of MC-type carbides using thermodynamic computational tools. A trial heat of a 50 lb AFA alloy ingot was made using conventional single-melt vacuum techniques, and the alloy was successfully hot-rolled without any cracking [2]. This heat showed good weldability, using filler material of the same alloy.

36 MATERIALS SCIENCE↗