Search NASA⌕ Search

Engineering topics

Bei, Hongbin

Publications and source records attributed to Bei, Hongbin.

At least 181 records · Page 10

Effects of FIB milling and pre-straining on the microstructure of directionally solidified Mo pillars: a Laue diffraction analysis

White beam Laue micro-diffraction was performed on directionally solidified, single-crystal Mo pillars in the as-grown state, after focused ion beam (FIB) milling and after pre-straining. The Laue diffraction peaks from the as-grown pillars are very sharp and show no broadening, similar to those from single-crystal Si wafers. Significant broadening and streaking of the peaks occurred after FIB milling and pre-straining, indicative of the damage these treatments induce in the nearly perfect crystal structure of the directionally solidified Mo pillars.

36 MATERIALS SCIENCE↗

Investigation of Strain-Induced Martensitic Transformation in Metastable Austenite using Nanoindentation

Strain-induced martensitic transformation of metastable austenite was investigated by nanoindentation of individual austenite grains in multi-phase steel. A cross-section prepared through one of these indented regions using focused ion beam milling was examined by transmission electron microscopy. The presence of martensite underneath the indent indicates that the pop-ins observed on the load-displacement curve during nanoindentation correspond to the onset of strain-induced martensitic transformation. The pop-ins can be understood as resulting from the selection of a favorable martensite variant during nanoindentation.

36 MATERIALS SCIENCE↗

3D X-ray Microprobe Investigation of Local Dislocation Densities and Elastic Strain Gradients in a NiAl-Mo Composite and Exposed Mo Micropillars as a Function of Pre-strain

3D spatially-resolved polychromatic microdiffraction was used to nondestructively probe the depth-dependent dislocation density and elastic strain gradients in separate phases of a NiAl Mo composite. Dislocation density and strain gradients are investigated before and after compressive strain. After plastic deformation important changes in the local stress state are found compared to the as grown composite. In as grown composites, due to the thermal expansion mismatch, the Mo phase is under compression and the NiAl phase is in tension. After compressive strain, the Mo phase is in tension and NiAl matrix is under compression. This result can be understood from the mismatch in yield strain of the composite material and from the elastic constraints during unloading. The dislocation density in both phases is found to grow with increased straining. These measurements provide quantitative dislocation information to guide recent directional solidified Mo micro-pillar testing. They also guide models of interface dynamics in composite materials.

36 MATERIALS SCIENCE↗

Specimen size effects on Zr-based bulk metallic glasses investigated by uniaxial compression and spherical nanoindentation

Specimen size effects on the mechanical behavior of Zr-based bulk metallic glasses (BMGs) were investigated by compression and nanoindentation tests. In compression, even at the 1- to 10-mm scale, stable shear band propagation and extensive plastic deformation can be achieved in small (2 mm) specimens, in contrast to large (6.5 mm) specimens, which fail catastrophically after limited plastic deformation. The yield strength is independent of specimen size in this range, and plastic deformation remains highly localized in a few shear bands even in those specimens that exhibit stable shear sliding. The fracture surfaces of small specimens are smooth, without the vein patterns normally observed as characteristic features on the fracture surfaces of BMGs. During spherical nanoindentation, it is found that the upper bound of the maximum shear stress to initiate plasticity (yielding) in a Zr-based BMG is almost constant for indenter radii smaller than {approx}90 {micro}m. However, the lower bound of this maximum shear stress decreases with increasing indenter radius, probably due to the increased probability of finding defects underneath larger indenters.

36 MATERIALS SCIENCE↗

Experimental identification and validation of models in micro and macro plasticity

For micro-macro approaches to finite plasticity, one needs experimental results on both scales, the engineering scale (macro scale) and the crystal scale (micro scale). Since we know that a monocrystal behaves different from a crystallite embedded in a polycrystal, one is also interested in data obtained on the micro scale of a polycrystal. Such data is needed not only for the identification of the material parameters like hardening variables, but also for the validation of these models. In this paper, experiments on both scales and, in parallel, FEM-simulations are presented, in order to compare the results of both approaches. The specimens stem from a rolled sheet of the deep-drawing steel DC04. On the micro scale indenter tests have been performed and the orientation changes in the volume below the indent have been measured using micron-resolution 3D x-ray microscopy (Larson et al., 2004, 2008). On the macro scale the usual tension tests and additional shear tests in different directions (Bouvier et al., 2006) have been performed. In corresponding simulations, the micro-macro transition is performed by a full constrained Taylor-model and, in order to overcome the drawbacks of the Taylor-model, the RVE technique has been applied.

36 MATERIALS SCIENCE↗

Influence of fatigue on the nanohardness of NiTiCr-wires

Testing parameters, such as rotational speed and bending radius, have a strong influence on the fatigue life of pseudoelastic NiTi shape-memory alloys during bending rotation fatigue (BRF) experiments [M. F. X. Wagner, Int. J. Mat. Res. 97 (2006), p. 1687-1696. and M. Frotscher, et al., Thermomechanical processing, microstructure and bending rotation fatigue of ultra-fine grained NiTiCr-wires, Proceedings of the International Conference for Shape Memory and Superelastic Technologies (SMST 2007), Tsukuba, Japan, ASM International, (2008), p. 149-158.]. Previous studies showed a decrease in the fatigue life for smaller bending radius (i.e. higher equivalent strain) and larger rotational speed. This observation is associated with an increase of dislocation density, the stabilization of stressinduced martensite during cycling, and an increase of the plateau stresses due to self-heating. In the present study, we examine the influence of these fatigue parameters on the nanohardness and shape recovery of pseudoelastic NiTiCr shape-memory alloy wires by nanoindentation. We show that nanoindentation is a suitable method for the characterization of fatigue-related microstructural changes, which affect the mechanical properties.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Enhanced plasticity in a Zr-based bulk metallic glass composite with in situ formed intermetallic phases

An in situ formed intermetallic phase/bulk metallic glass composite with high strength and good plasticity was fabricated by casting Zr{sub 55.0}Cu{sub 29.0}Ni{sub 8.0}Al{sub 8.0} melts. In situ formed tetragonal structured (Zr,Ni,Al){sub 2}(Cu,Ni,Al) intermetallic particles with a hardness of 9.6{+-}0.3 GPa improve the fracture strength of the composite. Micrographs of the fractured samples reveal that the shear band spacing is smaller than the intermetallic particles, indicating that they can effectively block shear band propagation before catastrophic fracture.

36 MATERIALS SCIENCE↗

Effect of alloying additions on phase equilibria and creep resistance of alumina-forming austenitic stainless steels

The high-temperature creep properties of a series of alumina-forming austenitic (AFA) stainless steels based on Fe-20Ni-(12-14)Cr-(2.5-4)Al-(0.2-3.3)Nb-0.1C (weight percent) were studied. Computational thermodynamics were used to aid in the interpretation of data on microstructural stability, phase equilibria, and creep resistance. Phases of MC (M: mainly Nb), M{sub 23}C{sub 6} (M: mainly Cr), B2 [{beta}-(Ni,Fe)Al], and Laves [Fe{sub 2}(Mo,Nb)] were observed after creep-rupture testing at 750 C and 170 MPa; this was generally consistent with the thermodynamic calculations. The creep resistance increased with increasing Nb additions up to 1 wt pct in the 2.5 and 3 Al wt pct alloy series, due to the stabilization of nanoscale MC particles relative to M{sub 23}C{sub 6}. Additions of Nb greater than 1 wt pct decreased creep resistance in the alloy series due to stabilization of the Laves phase and increased amounts of undissolved, coarse MC, which effectively reduced the precipitation of nanoscale MC particles. The additions of Al also increased the creep resistance moderately due to the increase in the volume fraction of B2 phase precipitates. Calculations suggested that optimum creep resistance would be achieved at approximately 1.5 wt pct Nb in the 4 wt pct Al alloy series.

36 MATERIALS SCIENCE↗

Effects of focused ion beam milling on the compressive behavior of directionally solidified micro-pillars and the nanoindentation response of an electro-polished surface

Focused ion beam (FIB) milling is the typical way in which micro-pillars are fabricated to study small-scale plasticity and size effects in uniaxial compression. However, FIB milling can introduce defects into the milled pillars. To investigate the effects of FIB damage on mechanical behavior, we tested Mo-alloy micro-pillars that were FIB milled following directional solidification, and compared their compressive response to pillars that were not FIB milled. We also FIB milled at glancing incidence a Mo-alloy single-crystal surface, and compared its nanoindentation response to an electro-polished surface of the same crystal. Consequences for the interpretation of data obtained from FIB milled micro-pillars are discussed.

36 MATERIALS SCIENCE↗

Thermal stability of Cr-Cr 3 Si eutectic microstructures

The thermal stability of Cr-Cr{sub 3}Si lamellar eutectic composites was investigated at temperatures up to 1400 C. In drop-cast Cr-Cr{sub 3}Si, coarsening was found to be interface controlled. The coarsening rate could be reduced by microalloying with Ce and Re, two elements which were chosen because they were expected to segregate to the Cr-Cr{sub 3}Si interfaces. Similarly, directional solidification, which is also expected to lower the Cr-Cr{sub 3}Si interfacial energy, was found to dramatically decrease the coarsening rate.

36 MATERIALS SCIENCE↗

Controlled normal/shear loading and shear fracture in bulk metallic glasses

Limited plasticity inhibits the engineering applications of bulk metallic glasses (BMGs), which often deform by the formation of localized shear bands. Overcoming the brittleness of BMGs necessitates advances in our understanding of the mechanisms of shear band initiation and propagation. Up to now, a major hurdle has been the ability to control the generation of shear bands and the associated fracture (e.g., by conventional uniaxial loading). Here we demonstrate a unique loading fixture that allows one not only to control the locations of shear band formation and shear fracture but also to alter the ratio of the normal to shear stress on the fracture plane. The capability of altering the stress ratio allows one to systematically examine how the normal stress affects shear fracture of BMGs. While some preliminary results with limited data have been presented in a prior publication, a comprehensive description of the unique test fixture is described here.

36 MATERIALS SCIENCE↗

Alloying effects of iridium on glass formation and glass-forming ability of the Zr-Cu-Al system

Alloying effects of iridium on the glass formability (GFA) of the Zr-Ir-Cu-Al system have been investigated, and several new bulk metallic glasses (BMGs) with high GFA have been successfully developed. Additions of Ir in the Zr-Cu-Al system can yield a beneficial distribution in atomic sizes, but the strong chemical interaction of the Zr-Ir atomic pair limits the maximum addable Ir contents and the resultant GFA. Our analyses indicate that the optimum composition for alloying elements is determined by not only topological but also chemical factors. Phase competition upon solidification, rather than effects from individual affecting factors, dictates the GFA of BMG systems.

36 MATERIALS SCIENCE↗

Directional recrystallization and microstructures of an Fe-6.5wt%Si alloy

Directional recrystallization of an Fe-6.5wt%Si alloy was investigated by changing hot zone temperatures and growth rates. Elongated (columnar) grains with an aspect ratio more than 10 can be produced when growth parameters are carefully adjusted. It was found that at a fixed growth rate, the grain length and aspect ratio increase with increased hot zone temperatures. At a fixed hot zone temperature, there is a critical growth rate at which columnar grains have the largest average aspect ratio. Below or above this growth rate, the aspect ratio decreases. Texture and grain orientation analysis showed that the preferentially selective growth to form columnar grains was favored by the formation of low-energy surfaces and grain boundaries.

36 MATERIALS SCIENCE↗

Development of Alumina-Forming Austenitic Stainless Steels

This paper presents the results of the continued development of creep-resistant, alumina-forming austenitic (AFA) stainless steel alloys, which exhibit a unique combination of excellent oxidation resistance via protective alumina (Al2O3) scale formation and high-temperature creep strength through the formation of stable nano-scale MC carbides and intermetallic precipitates. Efforts in fiscal year 2009 focused on the characterization and understanding of long-term oxidation resistance and tensile properties as a function of alloy composition and microstructure. Computational thermodynamic calculations of the austenitic matrix phase composition and the volume fraction of MC, B2-NiAl, and Fe2(Mo,Nb) base Laves phase precipitates were used to interpret oxidation behavior. Of particular interest was the enrichment of Cr in the austenitic matrix phase by additions of Nb, which aided the establishment and maintenance of alumina. Higher levels of Nb additions also increased the volume fraction of B2-NiAl precipitates, which served as an Al reservoir during long-term oxidation. Ageing studies of AFA alloys were conducted at 750 C for times up to 2000 h. Ageing resulted in near doubling of yield strength at room temperature after only 50 h at 750 C, with little further increase in yield strength out to 2000 h of ageing. Elongation was reduced on ageing; however, levels of 15-25% were retained at room temperature after 2000 h of total ageing.

36 MATERIALS SCIENCE↗

Development and Exploratory Scale-Up of Alumina-Forming Austenitic (AFA) Stainless Steels

This paper presents the results of the continued development of creep-resistant, alumina-forming austenitic (AFA) stainless steel alloys, which exhibit a unique combination of excellent oxidation resistance via protective alumina (Al2O3) scale formation and high-temperature creep strength through the formation of stable nano-scale MC carbides and intermetallic precipitates. Efforts in fiscal year 2009 focused on the characterization and understanding of long-term oxidation resistance and tensile properties as a function of alloy composition and microstructure. Computational thermodynamic calculations of the austenitic matrix phase composition and the volume fraction of MC, B2-NiAl, and Fe2(Mo,Nb) base Laves phase precipitates were used to interpret oxidation behavior. Of particular interest was the enrichment of Cr in the austenitic matrix phase by additions of Nb, which aided the establishment and maintenance of alumina. Higher levels of Nb additions also increased the volume fraction of B2-NiAl precipitates, which served as an Al reservoir during long-term oxidation. Ageing studies of AFA alloys were conducted at 750C for times up to 2000 h. Ageing resulted in near doubling of yield strength at room temperature after only 50 h at 750C, with little further increase in yield strength out to 2000 h of ageing. Elongation was reduced on ageing; however, levels of 15-25% were retained at room temperature after 2000 h of total ageing.

36 MATERIALS SCIENCE↗

The development of alumina-forming austenitic stainless steels for high-temperature structural use

Efforts at Oak Ridge National Laboratory to developAl2O3-forming austenitic (AFA) stainless steels for high-temperature (600-900 aC) structural use under aggressive oxidizing conditions are overviewed. Data obtained to date indicate the potential to achieve superior oxidation resistance to conventional Cr2O3-forming Fe- and Ni-base heat-resistant alloys, with creep strength comparable to state-of-the-art advanced austenitic stainless steels. Preliminary assessment also indicates the developed alloys are amenable to welding. Details of the alloy design approach and composition-microstructure-property relationships are presented.

36 MATERIALS SCIENCE↗

Efects of pre-strain on the compressive stress-strain response of Mo-alloy single crystal micro-pillars

A NiAl-Mo eutectic was directionally solidified to produce composites with well-aligned single-crystal Mo-alloy fibers embedded in a NiAl matrix. They were pre-strained by compressing along the fiber axis and then the matrix was etched away to expose free-standing micropillars having different sizes (360-1400 nm) and different amounts of pre-strain (0-11%). Compression testing of the pillars revealed a variety of behaviors. At one extreme were the as-grown pillars (0% pre-strain) which behaved like dislocation-free materials, with yield stresses approaching the theoretical strength, independent of pillar size. At the other extreme were pillars pre-strained 11% which behaved like the bulk, with reproducible stress-strain curves, relatively low yield strengths, stable work-hardening and no size dependence. At intermediate pre-strains (4-8%), the stress-strain curves were stochastic and exhibited considerable scatter in strength. This scatter decreased with increasing pre-strain and pillar size, suggesting a transition from discrete to collective dislocation behavior.

36 MATERIALS SCIENCE↗

Flow serration in a Zr-based bulk metallic glass in compression at low strain rates

It is demonstrated that at slow strain rates ({approx} 10{sup -4} s{sup -1}) in compression, the dominant room temperature macroscopic deformation mode in a ductile Zr-based bulk metallic glass is single shear along the principal shear plane. The stress-strain curve exhibited serrated flow in the plastic region. Scanning electron micrographs of the deformed samples revealed regularly spaced striations on the shear surface. A detailed analysis of the observed serrations disclosed that they were intimately related to the striations on the shear surface, suggesting that the serrations were mainly caused by intermittent sample sliding. Further investigations were conducted using in situ compression experiments; video images showed that there was indeed a one-to-one correspondence between the intermittent sliding and flow serration. The current study therefore suggests that flow serration is a result of intermittent sample sliding. This result also implies that the principal shear plane, once formed, is the preferential site for additional shear band formation

36 MATERIALS SCIENCE↗