Search NASA⌕ Search

Engineering topics

Bei, Hongbin

Publications and source records attributed to Bei, Hongbin.

At least 163 records · Page 9

Overview of strategies for high-temperature creep and oxidation resistance of alumina-forming austenitic stainless steels

A family of creep-resistant, alumina-forming austenitic (AFA) stainless steel alloys is under development for structural use in fossil energy conversion and combustion system applications. The AFA alloys developed to date exhibit comparable creep-rupture lives to state-of-the-art advanced austenitic alloys, and superior oxidation resistance in the {approx}923 K to 1173 K (650 C to 900 C) temperature range due to the formation of a protective Al{sub 2}O{sub 3} scale rather than the Cr{sub 2}O{sub 3} scales that form on conventional stainless steel alloys. This article overviews the alloy design approaches used to obtain high-temperature creep strength in AFA alloys via considerations of phase equilibrium from thermodynamic calculations as well as microstructure characterization. Strengthening precipitates under evaluation include MC-type carbides or intermetallic phases such as NiAl-B2, Fe{sub 2}(Mo,Nb)-Laves, Ni{sub 3}Al-L1{sub 2}, etc. in the austenitic single-phase matrix. Creep, tensile, and oxidation properties of the AFA alloys are discussed relative to compositional and microstructural factors.

36 MATERIALS SCIENCE↗

Texture Evolution and Phase Transformation in Titanium Investigated by In-Situ Neutron Diffraction

We report in-situ neutron diffraction studies of texture evolution and the (hcp) (bcc) phase transformation in commercially pure cold-drawn titanium upon continuous heating and cooling, complemented by differential scanning calorimetry (DSC) measurements. We show that the recrystallization of the phase at elevated temperature enhanced the preexisting fiber texture, which eventually facilitated the nucleation and growth of the phase favored by the Burgers orientation relationship, i.e., {0001} //{110} . More strikingly, upon completion of the transformation, the {110} texture (or preferred orientation) in was eliminated immediately by the rapid grain growth of intergranular allotriomorphs. This resulted in the loss of the original -texture when Ti was transformed back to from to upon subsequent cooling, distinct from the known texture memory effect for rolling textures in titanium. Our present work provides useful experimental results for understanding the mechanisms of texture evolution and phase transformation in titanium and its alloys and, by and large, low-symmetry alloys such as zirconium.

36 MATERIALS SCIENCE↗

3D X-ray Strain Microscopy in Two-Phase Composites at Submicron Length Scale

Author note: Part of this research summary is based on findings first reported in Refs. [3-5, 18]. Renewed interest in composite materials is driven by the fact that their mechanical properties can be superior to those of individual constituent phases. Interfaces between the phases are the key elements responsible for the unique micro-mechanisms of plastic deformation in composites. In this study the depth-dependent residual strain distributed in the two phases and partitioned across the composite interfaces is directly measured at submicron length-scale using X-ray microdiffraction and compared to a detailed simulation within the framework of micromechanical stress analysis. Interface strength is determined from the analysis of the so-called slip zone caused by the near-surface stress relaxation. Two examples are discussed including NiAl/Mo and Ni/Mo composites.

36 MATERIALS SCIENCE↗

Effect of Residual Stresses on the Hardness of Bulk Metallic Glasses

Nanoindentation experiments were conducted on Zr-based metallic glass samples, which were elastically and plastically bent in order to investigate the effect of residual stresses on hardness. It was found that tensile residual stress reduced the hardness significantly, while compressive residual stress produced only a small effect on the hardness. These observations are consistent with three-dimensional continuum-plasticity-based finite-element simulations. The hardness was also found to vary more significantly with residual stresses, in particular in tension, than that caused by shear-banding-induced softening, suggesting hardness measurement is a practical method for the evaluation of tensile residual stresses in a metallic glass. Hardness variation in the bent sample was correlated with the residual-stress induced volume dilatation through a free-volume-based model. In this paper, we also present a detailed stress analysis based on yield asymmetry under tension and compression to describe the distribution of residual stresses in bent metallic glass specimens. The calculations agree well with the hardness variations measured experimentally.

36 MATERIALS SCIENCE↗

On the Shear Band Direction in Metallic Glasses

This paper shows that it is inappropriate to relate the angle between loading axis and shear-band (or fracture) plane in metallic glasses under uniaxial loading conditions to the coefficient of internal friction in the Mohr-Coulomb model. Shear bands in metallic glasses are a result of material instability (which can be predicted from constitutive parameters and loading conditions), but not a yield phenomenon. Specifically, the shear band directions depend on Poisson s ratio, the ratios of three deviatoric principal stresses to Mises stress, the coefficient of internal friction, and the dilatancy factor. The last parameter describes whether the plastic flow is associative or non-associative. Theoretical predictions based on the classic Rudnicki-Rice model agree well with a compilation of observations in uniaxial mechanical tests. Furthermore, we identify three (two) regimes under the two-dimensional cylindrical (three-dimensional spherical) contact where different shear-band directions may occur. When using bonded interface technique to visualize the shear bands under the contact, it should be noted that the stress component normal to the bonded interface is released, resulting into the commonly observed semi-circular shear bands whose directions are predicted to follow the larger in-plane principal stress.

Gao, Yanfei↗

Effect of residual stresses on the onset of yielding in a Zr-based metallic glass

Indentation experiments were performed on as-cast and elastically-bent-and-constrained Zr-based metallic glass samples to investigate the effect of strain rate and residual stresses on the onset of yielding in the material. The critical shear stress for the onset of yielding in the as-cast sample was found to be insensitive to the applied strain rate. By contrast, in the elastically-stressed sample, the maximum contact pressure from the Hertzian stress field at the onset of yielding was found to largely decrease under tensile residual stress, but only slightly increase under compressive residual stress. Despite the different residual stresses, the effective shear stress, i.e. the superimposition of residual and Hertzian stress fields, for the onset of yielding in the Zr-based metallic glass was essentially a constant. The constancy of the effective stress for the onset of yielding was discussed in light of a critical excess volume associated with the atomic structure upon loading.

99 GENERAL AND MISCELLANEOUS↗

Indentation Schmid factor and orientation dependence of nanoindentation pop-in behavior of NiAl single crystals

Instrumented nanoindentation techniques have been widely used to characterize the small-scale mechanical behavior of materials. The elastic-plastic transition during nanoindentation is often indicated by a sudden displacement burst (pop-in) in the measured load-displacement curve. In defect-free single crystals, the pop-in is believed to be the result of homogeneous dislocation nucleation because the maximum shear stress corresponding to the pop-in load approaches the theoretical strength of the materials and because the statistical distribution of pop-in stresses is consistent with what is expected for a thermally activated process of homogeneous dislocation nucleation. This paper investigates whether this process is affected by crystallography and stress components other than the resolved shear stress. A Stroh formalism coupled with the two-dimensional Fourier transformation is used to derive the analytical stress fields in elastically anisotropic solids under Hertzian contact, which allows the determination of an indentation Schmid factor, namely, the ratio of maximum resolved shear stress to the maximum contact pressure. Nanoindentation tests were conducted on B2-structured NiAl single crystals with different surface normal directions. This material was chosen because it deforms at room temperature by {110}<001> slip and thus avoids the complexity of partial dislocation nucleation. Good agreement is obtained between the experimental data and the theoretically predicted orientation dependence of pop-in loads based on the indentation Schmid factor. Pop-in load is lowest for indentation directions close to <111> and highest for those close to <001>. In nanoindentation, since the stress component normal to the slip plane is typically comparable in magnitude to the resolved shear stress, we find that the pressure sensitivity of homogeneous dislocation nucleation cannot be determined from pop-in tests. Our statistical measurements generally confirm the thermal activation model of homogeneous dislocation nucleation. That is, the extracted dependence of activation energy on resolved shear stress is almost the same for all the indentation directions considered in this study, except for those close to <001>. Because very high pop-in loads are measured for orientations close to <001>, which implies a large contact area at pop-in, there is a higher probability of activating pre-existing dislocations in these orientations, which may explain the discrepancy near <001>.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Interface Strength in NiAl-Mo Composites from 3D X-ray Microdiffraction

The depth-dependent strain gradients near buried interfaces in a model system of NiAl-Mo composite were nondestructively probed with 3-D X-ray microdiffraction. Coupled with micromechanical analysis, our study shows that the relaxation of the residual thermal strains in the NiAl-Mo composites results in the formation of a near-surface 'slip zone' with large strain gradients in both the reinforcing Mo fibers and NiAl matrix. Based on these results an approach to calculate the fiber-matrix interface strength for composite materials is suggested.

36 MATERIALS SCIENCE↗

Determining the activation energies and slip systems for dislocation nucleation in body-centered cubic mo and face-centered cubic Ni single crystals

Nanoindentation tests were performed on single crystals of Mo and Ni. The critical shear stress for the first pop-in was {approx}1/7 of the shear modulus in both crystals. The dependence of pop-in probability on load was understood in terms of a thermally activated dislocation nucleation process. Comparison of the activation energies suggests nucleation of full dislocations in Mo and partial dislocations in Ni. The activation energy analysis also offers information on the specific slip system on which dislocations are nucleated.

36 MATERIALS SCIENCE↗

Creep in Directionally Solidified NiAl-Mo Eutectics

A directionally solidified NiAl-Mo eutectic and an NiAl intermetallic, having respective nominal compositions Ni-45.5Al-9Mo and Ni-45.2Al (at.%), were loaded in compression at 1073 and 1173 K. Formidable strengthening by regularly distributed Mo fibres (average diameter 600 nm, volume fraction 14%) was observed. The fibres can support compression stresses transferred from the plastically deforming matrix up to a critical stress of the order of 2.5 GPa, at which point they yield. Microstructural evidence is provided for the dislocation-mediated stress transfer from the NiAl to the Mo phase.

36 MATERIALS SCIENCE↗

Effects of boron on the microstructure and thermal stability of directionally solidiied NiAl-Mo eutectic

Microalloying with 0.01 at.% B decreases the range of growth speeds over which a well-aligned fibrous eutectic microstructure can be obtained in directionally solidified NiAl-Mo. Compared to the undoped alloy, the size/spacing of the Mo fibers is larger, and the fiber density smaller, in the B-doped alloy. Annealing at 1400 C coarsens the fibers by a mechanism involving fault migration and annihilation driven by diffusion along the fiber-matrix interface. The coarsening kinetics, given by the decrease in Mo fiber density with time, is exponential, and microalloying with B decreases the coarsening rate.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Effects of Ti, Zr, and Hf on the Phase Stability of Mo-Mo 3 Si+Mo 5 SiB 2 Alloys at 1600 C

Understanding the stability of the three-phase Mo{_}+Mo{sub 3}Si+Mo{sub 5}SiB{sub 2} region is important for alloy design of Mo-Si-B-based refractory metal intermetallic composites. In this work, thermodynamic modeling is coupled with guided experiments to study phase stability in this three-phase region of the Mo-Si-B-X (X = Ti, Zr, Hf) system. Both the calculated and experimental results show that additions of Zr and Hf limit significantly the stability of the three-phase region because of the formation of the ternary phases MoSiZr and MoSiHf, while Ti addition leads to a much larger region of stability for the three-phase equilibrium.

36 MATERIALS SCIENCE↗

X-ray diffraction study of the phase purity, order, and texture of ductile B2 intermetallics

Representatives (AgY, CuY, AgEr, CuDy, MgY and MgCe) of the newly discovered family of ductile stoichiometric B2 intermetallic (metal-rare-earth element, MR) compounds were characterized by X-ray diffraction, to determine if their anomalous ductility is related to an exceptional level of phase purity, lack of chemical ordering or a strong crystallographic texture. Brittle NiAl served as an anti-type in this study. We found that all of the rare-earth compounds, except MgY, have a significant volume fraction (-5-20vol.%) of second phases (M{sub 2}R intermetallics and R{sub 2}O{sub 3} oxides), which has not been reported in previous studies of these materials. The most ductile of observed MR compounds, AgY, is highly ordered. A moderate texture was observed in AgY, which may explain its higher ductility (using polycrystal modeling) as compared to other MR compounds. However, the intrinsic polycrystalline ductility of these compounds in the randomly textured state (like that observed in CuY) still has no specific, definitive explanation.

36 MATERIALS SCIENCE↗

Formation, stability, and crystal structure of &sigma; phase in Mo-Re-Si alloys

The formation, stability and crystal structure of the {sigma} phase in Mo-Re-Si alloys were investigated. Guided by thermodynamic calculations, six critically selected alloys were arc melted and annealed at 1600 C for 150 h. Their as-cast and annealed microstructures, including phase fractions and distributions, the compositions of the constituent phases and the crystal structure of the {sigma} phase were analyzed by thermodynamic modeling coupled with experimental characterization by scanning electron microscopy, electron probe microanalysis, X-ray diffraction and transmission electron microscopy. Two key findings resulted from this work. One is the large homogeneity range of the {sigma} phase region, extending from binary Mo-Re to ternary Mo-Re-Si. The other is the formation of a {sigma} phase in Mo-rich alloys either through the peritectic reaction of liquid + Mo{sub ss} {yields} {sigma} or primary solidification. These findings are important in understanding the effects of Re on the microstructure and providing guidance on the design of Mo-Re-Si alloys.

36 MATERIALS SCIENCE↗

Aging effects on the mechanical properties of alumina-forming austenitic stainless steels

Isothermal aging and tensile evaluation were conducted for recently developed alumina-forming austenitic stainless steels (AFAs). Microstructural observation reveals that NiAl-type B2 and Fe{sub 2}(Mo,Nb)-type Laves phase precipitates form as dominant second phases in the austenitic matrix during aging at 750 C. At room temperature these precipitates increase the strength but decrease the ductility of the AFA alloys. However, when tested at 750 C, the AFA alloys did not show strong precipitation hardening by these phases, moreover, the elongation to fracture was not affected by aging. Fracture surface and cross-sectional microstructure analysis after tensile testing suggests that the difference of mechanical behaviors between room temperature and 750 C results from the ductile-brittle transition of the B2 precipitates. At room temperature, B2 precipitates are strong but brittle, whereas they become weak but ductile above the ductile-brittle transition temperature (DBTT).

36 MATERIALS SCIENCE↗