Search NASA⌕ Search

Engineering topics

Bei, Hongbin

Publications and source records attributed to Bei, Hongbin.

At least 145 records · Page 8

Determination of interfacial mechanical properties of ceramic composites by the compression of micro-pillar test specimens

A novel method to determine the fiber-matrix interfacial properties of ceramic matrix composites is proposed and evaluated; where micro- pillar samples containing inclined fiber/matrix interfaces were prepared from a SiC fiber reinforced SiC matrix composites then compression-tested using the nano-indentation technique. This new test method employs a simple geometry and mitigates the uncertainties associated with complex stress state in the conventional single filament push-out method for the determination of interfacial properties. Based on the test results using samples with different interface orientations , the interfacial debond shear strength and the internal friction coefficient are explicitly determined and compared with values obtained by other test methods.

Shih, Chunghao↗

Relative effects of enthalpy and entropy on the phase stability of equiatomic high-entropy alloys

High configurational entropies have been hypothesized to stabilize solid solutions in equiatomic, multi-element alloys which have attracted much attention recently as high-entropy alloys with potentially interesting properties. To evaluate the usefulness of configurational entropy as a predictor of single-phase (solid solution) stability, we prepared five new equiatomic, quinary alloys by replacing individual elements one at a time in a CoCrFeMnNi alloy that was previously shown to be single-phase [1]. An implicit assumption here is that, if any one element is replaced by another, while keeping the total number of elements constant, the configurational entropy of the alloy is unchanged; therefore, the new alloys should also be single-phase. Additionally, the substitute elements that we chose, Ti for Co, Mo or V for Cr, V for Fe, and Cu for Ni, had the same room-temperature crystal structure and comparable size/electronegativity as the elements being replaced to maximize solid solubility consistent with the Hume-Rothery rules. For comparison, the base CoCrFeMnNi alloy was also prepared. After three-day anneals at elevated temperatures, multiple phases were observed in all but the base CoCrFeMnNi alloy suggesting that, by itself, configurational entropy is generally not able to override competing driving forces that also govern phase stability. Thermodynamic analyses were carried out for each of the constituent binaries in the investigated alloys (Co-Cr, Fe-Ni, Mo-Mn, etc,). Experimental results combined with the thermodynamic analyses suggest that, in general, enthalpy and non-configurational entropy have bigger influences on phase stability in equiatomic, multi-component alloys. Only when the alloy microstructure is a single-phase, approximately ideal solid solution does the contribution of configurational entropy to the total Gibbs free energy become dominant. Thus, high configurational entropy provides a way to rationalize, after the fact, why a solid solution forms (if it forms) but it is not a useful a priori predictor of which of the so-called high-entropy alloys will form single-phase solid solutions.

High-entropy alloys↗

The influences of temperature and microstructure on the tensile properties of a CoCrFeMnNi high-entropy alloy

An equiatomic CoCrFeMnNi high-entropy alloy, which crystallizes in the face-centered cubic (FCC) crystal structure, was produced by arc melting and drop casting. The drop-cast ingots were homogenized, cold rolled, and recrystallized to obtain single-phase microstructures with three different grain sizes in the range 4~160 m. Quasi-static tensile tests were then performed at temperatures between 77 and 1073 K. Yield strength, ultimate tensile strength and ductility all increased with decreasing temperature. During the initial stages of plasticity (up to ~2% strain), deformation occurs by planar dislocation glide on the normal FCC slip system {111} 110 at all temperatures and grain sizes investigated. Undissociated 1/2 110 dislocations were observed, as were numerous stacking faults, which imply the dissociation of several of these dislocations into 1/6 112 Shockley partials. At later stages ( 20% strain), nanoscale deformation twins were observed after interrupted tests at 77 K, but not in specimens tested at room temperature where plasticity occurred exclusively by dislocations which organized into cells. Deformation twinning, by continually decreasing the mean free path of dislocations during tensile testing, produces a high degree of work hardening and a significant increase in the ultimate tensile strength. This increased work hardening prevents the early onset of necking instability and is a reason for the enhanced ductility observed at 77 K. A second way in which twinning can contribute to ductility is by providing an additional deformation mode to accommodate plasticity. However, it cannot explain the increase in yield strength with decreasing temperature in our high-entropy alloy since twinning was not observed in the early stages of plastic deformation. Since strong temperature dependencies of yield strength are also seen in binary FCC solid solution alloys, it may be an inherent solute effect, which needs further study.

Deformation twinning↗

Rapid Relaxation and Embrittlement of Zr-based Bulk Metallic Glasses by Electropulsing

Mechanical relaxation and embrittlement of Zr52.5Cu17.9Ni14.6Al10Ti5 bulk metallic glasses were achieved rapidly by the direct current electropulsing treatment. The temperature profile was recorded by an infrared camera and it was found to be non-uniform in the treated specimen. Specifically, temperatures below the glass transition temperature, near and above the crystallization temperature could be ach- ieved, respectively, at different locations in the same treated specimen. Two sets of nanoindentation were conducted. While the first set investigated the mechanical properties of three individually elec- tropulsed specimens with different conditions, the second set indented a single treated specimen along its temperature gradient. Both sets of indentation revealed that by Joule heating to different tempera- tures, relaxation, embrittlement, and crystallization were significantly accelerated by electrical pulses. Results suggest that electropulsing provides an opportunity to simultaneously achieve plastic forming and mechanical property control of metallic glasses.

Yiu, P↗

Re Effects on Phase Stability and Mechanical Properties of MoSS+Mo3Si+Mo5SiB2 alloys

Because of their high melting points and good oxidation resistance Mo-Si-B alloys are of interest as potential ultrahigh-temperature structural materials. But their major drawbacks are poor ductility and fracture toughness at room temperature. Since alloying with Re has been suggested as a possible solution, we investigate here the effects of Re additions on the microstructure and mechanical properties of a ternary alloy with the composition Mo-12.5Si-8.5B (at.%). This alloy has a three-phase microstructure consisting of Mo solid-solution (MoSS), Mo3Si, and Mo5SiB2 and our results show that up to 8.4 at.% Re can be added to it without changing its microstructure or forming any brittle phase at 1600 C. Three-point bend tests using chevron-notched specimens showed that Re did not improve fracture toughness of the three-phase alloy. Nanoindentation performed on the MoSS phase in the three-phase alloy showed that Re increases Young s modulus, but does not lower hardness as in some Mo solid solution alloys. Based on our thermodynamic calculations and microstructural analyses, the lack of a Re softening effect is attributed to the increased Si levels in the Re-containing MoSS phase since Si is known to increase its hardness. This lack of softening is possibly why there is no Re-induced improvement in fracture toughness.

Yang, Ying↗

Thermodynamic Modeling and Experimental Study of the Fe-Cr-Zr System

Wide applications of zircaloys, stainless steels and their interactions in nuclear reactors require the knowledge on phase stability and thermodynamic property of the Fe-Cr-Zr system. This knowledge is also important to develop new Zr-contained Fe-Cr ferritic steels. This work aims at developing thermodynamic models for describing phase stability and thermodynamic property of the Fe-Cr-Zr system using the Calphad approach coupled with experimental study. Thermodynamic descriptions of the Fe-Cr and Cr-Zr systems were either directly adopted or slightly modified from literature. The Fe-Zr system has been remodeled to accommodate recent ab-initio calculation of formation enthalpies of various Fe-Zr compounds. Reliable ternary experimental data and thermodynamic models were mainly available in the Zr-rich region. Therefore, selected ternary alloys located in the vicinity of the eutectic valley of (Fe,Cr,Zr) and (Fe,Cr)2Zr laves phase in the Fe-rich region have been experimentally investigated in this study. Microstructure has been examined by using scanning electron microscope, energy-dispersive Xray spectroscopy and X-ray diffraction. These experimental results, along with the literature data were then used to develop thermodynamic models for phases in the Fe-Cr-Zr system. Calculated phase equilibria and thermodynamic properties of the ternary system yield satisfactory agreements with available experimental data, which gives the confidence to use these models as building blocks for developing a Zr, Fe and Cr contained multicomponent thermodynamic database for broader applications in nuclear reactors.

Yang, Ying↗

Grain-boundary strengthening in nanocrystalline chromium and the Hall- Petch coefficient of body-centered cubic metals

Nanocrystalline Cr (nc-Cr) was synthesized by electrodeposition. Samples with various grain sizes (19 57 nm) were prepared by annealing the as-deposited sample. Microstructures were examined using X-ray and electron microscopy, and the mechanical prop- erties were evaluated using nanoindentation. The strength of nc-Cr samples apparently obeyed the classical Hall Petch relationship. It was found that hardening potency caused by grain refinement was generally higher in body-centered cubic metals than that in face-centered cubic and hexagonal close-packed metals. A possible explanation was offered.

Wu, Dong↗

Acquisition, Sharing and Processing of Large Datasets for Strain Imaging: an Example of an Indented Ni3Al/Mo Composite

The local effects of stress from a mechanical indentation have been studied on a Ni3 Al single crystal containing submicron inclusions of molybdenum fibers. Polychromatic X ray Microscopy (PXM) was used to measure elastic and plastic deformations near the indents. Analysis of freshly acquired massive sets of PXM data has been carried out over the Science Studio network using parallel processing software FOXMAS. This network and the FOXMAS software have greatly improved the efficiency of the data processing task.. The analysis was successfully applied to study lattice orientation distribution and strain tensor components for both the Ni3 Al and the Mo phases, particularly around 8 indents patterned at the longitudinal section of the alloy.

data processing↗

Phase-Specific Elastic/Plastic Interface Interactions in Layered Cr-NiAl Structures

The depth-dependent, as-grown and deformation-induced strain and dislocations partitioned through the interfaces in a two-phase layered NiAl-Cr(Mo) structure are directly measured at the mesoscale using 3-D X-ray microdiffraction. It is demonstrated that in the as-grown, undeformed state, neighboring submicron Cr solid solution and NiAl eutectic lamellae (doped with {approx}3% Mo) form a heterointerface with 180{sup o} rotation around a <1 1 2> pole. It is shown that the mechanical response to the indentation of a layered composite with alternating Cr(Mo)-NiAl lamellae is distinct from the response of single-phase materials. In the center of the indent, after the load is released, the NiAl lamellae are under compressive forward stresses (with the same sign as the indentation-induced compression) while Cr solid solution lamellae are under tensile back stresses (with opposite sign from the indentation load). The depth-dependent alternation of compressive/tensile residual strains in the neighboring Cr solid solution and NiAl lamellae is understood in the framework of the Mughrabi's composite model considering two types of structure elements: harder and softer regions. Under indentation, both kinds of lamellae are assumed to deform compatibly. After the load is released, residual forward stresses are formed in the harder lamellae, and back stresses are formed in the mechanically softer lamellae. Line-broadening analysis of the intensity distribution along the diffraction vector reveals a 15-times increase in dislocation density in the near-surface zone in the center of the indent. Such a large increase is typical for severe deformation.

36 MATERIALS SCIENCE↗

Experimental Analysis of the Elastic Plastic Transition During Nanoindentation of Single Crystal a-Silicon Nitride

The elastic-to-plastic transition in single crystal a-silicon nitride was experimentally characterized through a series of nanoindentation experiments using a spherical indenter. The experimental results provide a quantitative description of the critical shear strengths for the transition, as well as estimates of the shear modulus and nanohardness of the material.

36 MATERIALS SCIENCE↗