Search NASA⌕ Search

Engineering topics

Bei, Hongbin

Publications and source records attributed to Bei, Hongbin.

At least 55 records · Page 3

Temperature-dependent defect accumulation and evolution in Ni-irradiated NiFe concentrated solid-solution alloy

Temperature significantly affects defect migration and evolution in irradiated materials. However, the effects of temperature on defect evolution in concentrated solid-solution alloys (CSAs), including high entropy alloys, are not well understood, despite their potential as structural materials in advanced nuclear reactors. As an important model system of these CSAs, equiatomic Ni 50 Fe 50 (NiFe) was selected to understand the effects of temperature on defect evolution during irradiation and subsequent thermal annealing. Specifically, defect accumulation and evolution in NiFe alloy under Ni-ion irradiation at 150, 300, and 500 K were studied, and the irradiated specimens were subsequently annealed at higher temperatures. Rutherford backscattering spectrometry along the <100> channeling direction was employed to study damage accumulation and evolution before and after each irradiation and annealing experiment. Here we show that more defects survive and accumulate at 150 K, but more importantly defects can migrate to deeper depths at this low irradiation temperature. Irradiation-induced damage at 150 and 300 K does not recover substantially after post-irradiation annealing at 500 K, but dramatic recovery is observed after post-irradiation annealing at 700 K, indicating an onset temperature of defect recovery between 500 and 700 K. Here, the migration of irradiation-induced defects upon annealing is closely related to the mobility and stress state arising from the surviving defects. With the consideration of five stages of defect recovery in conventional dilute alloys, the underlying mechanisms for temperature-dependent defect accumulation and evolution in NiFe CSA are discussed.

36 MATERIALS SCIENCE↗

Effect of electronic energy dissipation on strain relaxation in irradiated concentrated solid solution alloys

The effect of energy deposition by energetic particles on Ni and two single-phase concentrated solid solution alloys (NiFe and NiCoCrFe) is explored through combined experimental and modelling efforts. Damage evolution as a function of increasing ion fluence is monitored via elastic strain developed in the irradiated crystals. We show that damage produced from displacement collision cascades is sensitive to subsequent highly ionizing irradiation that the strain generated by elastic nuclear collisions undergoes partial relaxation upon high-energy irradiation. This result suggests a change in the damage structure upon electronic energy deposition due to both predominant defect annealing and growth of small defect clusters. Strain relaxation, more pronounced in the alloys than in Ni, is ascribed to both higher thermal conductivity and weaker electron-phonon coupling in Ni.

36 MATERIALS SCIENCE↗

Channeling analysis in studying ion irradiation damage in materials containing various types of defects

We present that ion channeling is a powerful quantitative technique for studying ion-irradiation induced defect evolution in single crystalline materials. An iterative procedure to determine dechanneling yields has been developed for decades, serving as a major method for analyzing experimental channeling data. The applicability of such procedure is, however, generally limited to the crystalline damage with only point defects and local amorphous domains. For the other cases, such as irradiated metals, the assumption of direct-backscattering free has usually been made. In the present study, Ni, TiAl, MgO, and SrTiO 3 single crystals are selected as four model materials, representing metals, intermetallic alloys, and ceramic compounds with different defect evolution processes under irradiation, to investigate the fidelity of applying dechanneling analysis on various types of defects. The pure dechanneling assumption is shown oversimplified in Ni irradiated with low fluence self-ions and may result in error on the derived damage profile. Moreover, the iterative procedure of dechanneling analysis is shown valid for more general situations than the randomly distributed atoms, including those not exhibiting a peak in channeling spectra. The disappearance of damage peak in channeling spectra is attributed to the combined effects of small (but non-zero) scattering factor, long-range damage effects, and non-ignorable damage level in pristine crystals. Furthermore, the ratio of direct backscattering to dechanneling areas provides information on defect configurations in the materials containing a well-defined damage peak in channeling spectra. Finally, the contribution from dechanneling sources increases from SrTiO 3 , TiAl, to MgO, according to the derived scattering and dechanneling factors.

36 MATERIALS SCIENCE↗

Chemically-biased diffusion and segregation impede void growth in irradiated Ni-Fe alloys

Recent irradiations of Ni-Fe concentrated solid solution alloys have demonstrated significant improvement of radiation performance. This improvement is attributed to redistribution of the alloying elements near sinks of point defects (voids, dislocations) due to chemically-biased atomic diffusion, where vacancies have preference to migrate via Fe atoms and interstitials via Ni atoms. In Ni-Fe, all sinks are enriched by Ni atoms, which strongly affects further interactions of radiation-produced mobile defects with voids and dislocations, hence void growth and dislocation climb. Ni-decorated sinks interact stronger with interstitial atoms than vacancies, which enhances dislocation loops growth. At the same time, Ni segregation creates Fe-enriched “channels” for vacancy migration out of the damage region to agglomerate in the outer regions, inaccessible to interstitial atoms. Furthermore, strong effect of chemically-biased diffusion is supported by transmission electron microscope characterization and calls for special attention in designing alloys with desired properties through tuning defect mobilities.

36 MATERIALS SCIENCE↗

Effects of Fe concentration on helium bubble formation in NiFe x single-phase concentrated solid solution alloys

The formation of helium bubbles and the consequential property degradation are critical challenges for materials used in advanced nuclear energy systems. The mechanism of helium bubble formation in a series of NiFe x (x = 0, 20, 35, or 50 at.%) single-phase concentrated solid solution alloys (SP-CSAs) are studied in this work. Transmission electron microscopy analysis shows that with increasing Fe concentration, the average bubble size decreases while the bubble number density increases, indicating the growth of large helium bubbles in NiFe x SP-CSAs is suppressed by increasing the alloy chemical complexity through increased Fe concentration. Mechanisms for the slower bubble growth rate in NiFe x binary SP-CSAs compared Ni are identified. These mechanisms include promotion of Frenkel pair recombination, denser and more homogeneously distributed nucleation sites, and increased helium atom densities inside the bubbles. Here, the results demonstrate that optimizing the chemical complexity in SP-CSAs can be an effective approach to design materials with superior resistance to helium bubble nucleation and growth.

36 MATERIALS SCIENCE↗

Predictive multiphase evolution in Al-containing high-entropy alloys

The ability to predict and understand phases in high-entropy alloys (HEAs) is still being debated, and primarily true predictive capabilities derive from the known thermodynamics of materials. The present work demonstrates that prior work using high-throughput first-principles calculations may be further utilized to provide direct insight into the temperature- and composition-dependent phase evolution in HEAs, particularly Al-containing HEAs with a strengthening multiphase microstructure. Using a simple model with parameters derived from first-principles calculations, we reproduce the major features associated with Al-containing phases, demonstrating a generalizable approach for exploring potential phase evolution where little experimental data exists. Neutron scattering, in situ microscopy, and calorimetry measurements suggest that our high-throughput Monte Carlo technique captures both qualitative and quantitative features for both intermetallic phase formation and microstructure evolution at lower temperatures. This study provides a simple approach to guide HEA development, including ordered multi-phase HEAs, which may prove valuable for structural applications.

36 MATERIALS SCIENCE↗

Helium irradiated cavity formation and defect energetics in Ni-based binary single-phase concentrated solid solution alloys

In this study, binary single-phase concentrated solid solution alloys (SPCSAs), including Ni 80 Co 20 , Ni 80 Fe 20 , Ni 80 Cr 20 , Ni 80 Pd 20 , and Ni 80 Mn 20 (in atomic percentage), were irradiated with 200 keV He + ions at 500 °C. He cavity size and density distribution were systematically investigated using transmission electron microscope. Here we show that alloying elements have a clear impact on He cavity formation. Cavity size is the smallest in Ni 80 Mn 20 but the largest in Ni 80 Co 20 . Alloying elements could also substantially affect cavity density profile. In-depth examination of cavities at peak damage region (~500 nm) and at low damage region (~300 nm) demonstrates that cavity size is depth (damage) dependent. Competition between consumption and production of vacancies and He atoms could lead to varied cavity size. Density functional theory (DFT) calculations were performed to obtain the formation and migration energies of interstitials and vacancies. Combined experimental and simulation results show that smaller energy gap between interstitial and vacancy migration energies may lead to smaller cavity size and narrower size distribution observed in Ni 80 Mn 20 , comparing with Ni 80 Co 20 . Finally, the results of this study call attention to alloying effects of specific element on cavity formation and defect energetics in SPCSAs, and could provide fundamental understanding to predict radiation effects in more complexed SPCSAs, such as high entropy alloys.

36 MATERIALS SCIENCE↗

Enhanced strength and ductility of a tungsten-doped CoCrNi medium-entropy alloy

Developing metallic materials with a good combination of strength and ductility has been an unending pursuit of materials scientists. The emergence of high/medium-entropy alloys (HEA/MEA) provided a novel strategy to achieve this. In this work, we also strengthened a strong-and-ductile MEA using a traditional solid solution strengthening theory. The selection of solute elements was assisted by mechanical property and microstructure predictive models. Extensive microstructural characterizations and mechanical tests were performed to verify the models and to understand the mechanical behavior and deformation mechanisms of the designated CoCrNi–3W alloy. Our results show good experiment-model agreement. The incorporation of 3 at.% W into the ternary CoCrNi matrix increased its intrinsic strength by ~20%. External strengthening through microstructural refinement led to a yield strength nearly double that of the parent alloy, CoCrNi. The increase in strength is obtained with still good ductility when tested down to 77 K. Nanoscale twin boundaries are observed in the post-fracture microstructure under 77 K. Finally, the combination of strength and ductility after W additions deviate from the traditional strength-ductility-trade-off contour.

36 MATERIALS SCIENCE↗

Interstitial migration behavior and defect evolution in ion irradiated pure nickel and Ni-xFe binary alloys

Transition from long-range one-dimensional to short-range three-dimensional migration modes of interstitial defect clusters greatly reduces the damage accumulation in single-phase concentrated solid solution alloys under ion irradiation. A synergetic investigation with experimental, computational and modeling approaches revealed that both the resistance to void swelling and the delay in dislocation evolution in Ni-Fe alloys increased with iron concentration. This was attributed to the gradually increased sluggishness of defect migration, which enhances interstitial and vacancy recombination. Transition from long-range one-dimensional defect motion in pure nickel to short-range three-dimensional motion in concentrated Ni-Fe alloys is continuum, not abrupt, and within an iron concentration range up to 20%. Lastly, the gradual transition process can be quantitatively characterized by the mean free path of the interstitial defect clusters.

36 MATERIALS SCIENCE↗

Irradiation responses and defect behavior of single-phase concentrated solid solution alloys

Single-phase concentrated solid solution alloys (SP-CSAs) are newly emerging advanced structural materials, which are defined as multiprincipal element solid solutions. SP-CSAs with more than four components in equimolar or near-equimolar ratios are also referred to as high-entropy alloys due to their high configurational entropy. SP-CSAs are potential structural materials in advanced nuclear energy systems due to their attractive mechanical properties. Therefore many investigations have been carried out to study the irradiation-induced structural damage and defect behavior in SP-CSAs. This paper reviews recent experimental results on the irradiation responses of various SP-CSAs, focusing on the accumulation of irradiation-induced structural damage, void swelling resistance, and solute segregation behavior. In addition, the characteristic defect behavior in SP-CSAs derived from ab initio and molecular dynamics simulations, as well as the challenges in the applications of SP-CSAs for the nuclear energy systems are briefly discussed.

36 MATERIALS SCIENCE↗

Influence of irradiation temperature on void swelling in NiCoFeCrMn and NiCoFeCrPd

Here, using ion irradiation and transmission electron microscopy, temperature dependent void swelling and dislocation loop evolution in equiatomic NiCoFeCrMn and NiCoFeCrPd high entropy alloys were investigated. Voids were observed in all tested conditions. An order higher of swelling was observed in both HEAs as temperature increased from 420 to 580 °C. Alloying with Pd was found to have a stronger suppression effect on void and dislocation loop growth than alloying with Mn. Possible contributions to the swelling resistance were explored, including localized lattice distortion and higher defect migration barrier in NiCoFeCrPd. Additionally, no phase decomposition was observed in either alloy.

36 MATERIALS SCIENCE↗

Enhanced void swelling in NiCoFeCrPd high-entropy alloy by indentation-induced dislocations

The role of dislocations on ion irradiation-induced void formation is studied in a high-entropy alloy (HEA) NiCoFeCrPd. Despite previous observations that show high-entropy alloys are swelling resistant due to a high defect recombination rate, the swelling is enhanced with increasing density of pre-existing dislocations at low strain levels that shortened transient duration before the onset of void swelling. Under certain irradiation conditions, a high density of dislocations may carry the material closer to the sink-dominated regime. Finally, compared to another HEA NiCoFeCrMn, NiCoFeCrPd has a smaller loop size and higher loop density due to the stronger lattice distortion.

36 MATERIALS SCIENCE↗

Quantifying early stage irradiation damage from nanoindentation pop-in tests

Early stage irradiation effects on incipient plasticity are quantitatively investigated in single-crystalline molybdenum using nanoindentation pop-in tests. Defects produced under low-dose ion irradiations, even when they are hardly detected by ion-channeling technique, can significantly reduce the critical stress for the elastic-plastic transition, through acting as heterogeneous dislocation nucleation sources. Here, the density and strength of defects are derived using a unified model convoluting homogeneous and heterogeneous mechanisms. In addition to the increased defect density, defect strength is found to decrease with increasing irradiation dose, suggesting a growth in defect size, which is further evidenced by combined analyses between pop-in and hardness tests.

36 MATERIALS SCIENCE↗

In situ neutron diffraction study on tensile deformation behavior of carbon-strengthened CoCrFeMnNi high-entropy alloys at room and elevated temperatures

In this paper, carbon is doped into a CoCrFeMnNi high-entropy alloy as an interstitial atom, improving the single phase solid solution alloy with a good combination of strength and ductility at room temperature by introducing deformation twins. In situ neutron diffraction (ND) is applied to investigate the carbon-doped CoCrFeMnNi deformation mechanism and micromechanical behaviors during uniaxial tension at room and elevated temperatures. With in situ results accompanied with the microstructure and texture measurement, it is found that the plastic deformation is dominated by dislocation slip at an early stage at both temperatures. However, at high strain level, deformation is mediated simultaneously by deformation twins and microbands at room temperature, while it is governed solely by microbands at elevated temperature of 573 K. The evolution of lattice strain, peak intensity, and peak width from in situ ND elucidates the micromechanical behaviors regarding the role of slips and twins. Finally, the texture represented by orientation distribution function indicates that the initial specimen possesses a relatively strong {112} <110> texture component, and the room-temperature tension deformed texture comprises of slip-induced fiber texture and twinning-induced {115} <552> texture component.

36 MATERIALS SCIENCE↗

Local lattice distortion in NiCoCr, FeCoNiCr and FeCoNiCrMn concentrated alloys investigated by synchrotron X-ray diffraction

Severe lattice distortion is presumptively considered as a core effect of high-entropy alloys, but quantitative measurements are still missing. Here, we demonstrate that the lattice distortion in high-entropy alloys can be quantitatively analyzed based on pair distribution function obtained from synchrotron X-ray diffraction. By applying this method to equiatomic NiCoCr, FeCoNiCr and FeCoNiCrMn concentrated alloys, we found that the local lattice distortion in the NiCoCr (0.23%) and FeCoNiCrMn (0.24%) alloys are comparable while negligible in the FeCoNiCr alloy (0.04%). Furthermore, the origin of local lattice distortion in the NiCoCr and FeCoNiCrMn concentrated alloys was discussed.

36 MATERIALS SCIENCE↗