Search NASA⌕ Search

Engineering topics

Bei, Hongbin

Publications and source records attributed to Bei, Hongbin.

At least 73 records · Page 4

Microband induced plasticity and the temperature dependence of the mechanical properties of a carbon-doped FeNiMnAlCr high entropy alloy

Highlights: • A superior fcc HEA with the strength of 1.5 GPa at the cryogenic condition is developed. • The strengthening mechanisms of HEAs at different temperatures are clarified. • The temperature dependence of MBIP effect is revealed. - Abstract: The uniaxial mechanical properties of the high entropy alloy (HEA) Fe{sub 40.4}Ni{sub 11.3}Mn{sub 34.8}Al{sub 7.5}Cr{sub 6} doped with 1.1 at.% C have been determined for both the as-cast and recrystallized states at temperatures from 77 to 973 K. Very high yield strengths were obtained at 77 K of 928 MPa for the as-cast HEA and 1037 MPa for the recrystallized HEA. The yield strength decreased sharply to 293 K and more slowly to 973 K, where it was ~200 MPa [11] in both conditions. The lattice friction stress, which results from the increase of the Peierls barrier, was the major contributor to the large yield strength at 77 K. On the other hand, the grain boundaries lose their strengthening ability at a high temperature, which largely accounts for the sharp drop in yield strength of the fine-grained (5 μm) recrystallized HEA at 973 K. The elongation to failure was highest at 293 K and 673 K with the lowest values at 77 K. Transmission electron microscopy was used to study the effects of temperature on the deformation mechanisms of the HEAs, especially the temperature dependence of the microband-induced plasticity effect. At temperatures ranging from 77 K to 673 K microbands form in the as-cast HEA, while dislocation clusters were observed in the recrystallized HEA over this temperature range. Only tangled dislocations were found at 973 K for both the as-cast and recrystallized HEA due to thermally-activated deformation.

36 MATERIALS SCIENCE↗

Single-Phase Concentrated Solid-Solution Alloys: Bridging Intrinsic Transport Properties and Irradiation Resistance

Single-phase concentrated solid-solution alloys (SP-CSAs), including high entropy alloys (HEAs), are compositionally complex but structurally simple, and provide a playground of tailoring material properties through modifying their compositional complexity. The recent progress in understanding the compositional effects on the energy and mass transport properties in a series of face-centered-cubic SP-CSAs is the focus of this review. Relatively low electrical and thermal conductivities, as well as small separations between the interstitial and vacancy migration barriers have been generally observed, but largely depend on the alloying constituents. We further discuss the impact of such intrinsic transport properties on their irradiation response; the linkage to the delayed damage accumulation, slow defect aggregation, and suppressed irradiation induced swelling and segregation has been presented. We emphasize that the number of alloying elements may not be a critical factor on both transport properties and the defect behaviors under ion irradiations. Furthermore, the recent findings have stimulated novel concepts in the design of new radiation-tolerant materials, but further studies are demanded to enable predictive models that can quantitatively bridge the transport properties to the radiation damage.

36 MATERIALS SCIENCE↗

Extremely hard amorphous-crystalline hybrid steel surface produced by deformation induced cementite amorphization

Amorphous and nanograined (NG) steels are two categories of strong steels. However, over the past decade, their application has been hindered by their limited plasticity, the addition of expensive alloying elements, and processing challenges associated with producing bulk materials. Here in this work, we report that the surface of a carburized Fe-Mn-Si martensitic steel with extremely low elemental alloying additions can be economically fabricated into an amorphous-nanocrystalline hybrid structure. Atom probe tomography and nanobeam diffraction of a hard turned steel surface together with molecular dynamics (MD) simulations reveal that the original cementite surface structure experiences a size-dependent amorphization and phase transformation during heavy plastic deformation. MD simulations further show that the martensite-cementite interface serves as a nucleation site for cementite amorphization, and that cementite can become disordered if further strained when the cementite particles are relatively small. These graded structures exhibit a surface hardness of ~16.2 GPa, which exceeds the value of ~8.8 GPa for the original nanocrystalline martensitic steel and most nanocrystalline steels reported before. Finally, this practical and cost-efficient approach for producing a hard surface with retained bulk ductility and toughness can provide expanded opportunities for producing an amorphous-crystalline hybrid structure in steels and other alloy systems.

36 MATERIALS SCIENCE↗

Radiation-induced extreme elastic and inelastic interactions in concentrated solid solutions

One of the biggest challenges in the radiation induced defect science is to understand the complex nature of ion-atom interactions under highly extreme conditions. Here, we report the irradiation induced non-equilibrium defect formation in NiCoCr single phase concentrated solid solution alloy due to (i) the extreme inelastic and (ii) the coupled inelastic and elastic ion-atom interactions. These two conditions are achieved at 5 and 30 μm penetration depths along the paths of swift heavy ions (1.542 GeV Bi). In general, the irradiation induced damage consists of interstitial-type dislocation loops and vacancy-type stacking fault tetrahedra (SFT). Near the surface (~5 μm) where electronic energy loss is dominating (~62.5 keV nm –1 ), the atomic motion primarily results in the formation of SFT. A noticeable increase of dislocation loop formation is observed at 30 μm near the maximum energy deposition from elastic interactions (~4.9 keV nm –1 ), as compared to the near surface region (~0.06 keV nm –1 ). As a result, insights on the complex electronic and atomic correlations of extreme energy deposition and dissipation on defect dynamics and structural stability may pave the way for new design principles of radiation–tolerant structural alloys.

36 MATERIALS SCIENCE↗

Fabrication of highly dense isotropic Nd-Fe-B nylon bonded magnets via extrusion-based additive manufacturing [Fabrication of highly dense isotropic Nd-Fe-B bonded magnets via extrusion-based additive manufacturing]

Magnetically isotropic bonded magnets with a high loading fraction of 70 vol.% Nd-Fe-B are fabricated via an extrusion-based additive manufacturing, or 3D printing system that enables rapid production of large parts. The density of the printed magnet is ~5.2 g/cm 3 . The room temperature magnetic properties are: intrinsic coercivity H ci = 8.9 kOe (708.2 kA/m), remanence B r = 5.8 kG (0.58 T), and energy product (BH)max = 7.3 MGOe (58.1 kJ/m 3 ). The as-printed magnets are then coated with two types of polymers, both of which improve the thermal stability as revealed by flux aging loss measurements. Tensile tests performed at 25 °C and 100 °C show that the ultimate tensile stress (UTS) increases with increasing loading fraction of the magnet powder, and decreases with increasing temperature. AC magnetic susceptibility and resistivity measurements show that the 3D printed Nd-Fe-B bonded magnets exhibit extremely low eddy current loss and high resistivity. Lastly, we demonstrate the performance of the 3D printed magnets in a DC motor configuration via back electromotive force measurements.

36 MATERIALS SCIENCE↗

Effect of alloying elements on defect evolution in Ni-20X binary alloys

The effect of alloying elements on radiation-induced microstructural evolution in Ni and Ni-20X (X = Fe, Cr, Mn and Pd) binary alloys was investigated using ion irradiation and cross-sectional transmission electron microscopy. The three-dimensional migration mode is identified to be the dominating migration mechanism for interstitial clusters in these binary alloys, contrary to the one-dimensional mode that dominates in the well-studied dilute alloys. The results reveal that: (1) the average size of defect clusters decreases as the solute atomic volume size factor increases. Smaller void size in Ni-20Cr is attributed to faster vacancy mobility in the near surface region, and weaker vacancy binding energy beyond the irradiation peak than Ni-20Fe. The smaller voids observed in Ni-20Mn and Ni-20Pd beyond the damage peak are due to the stronger Mn/Pd-vacancy binding effect of largely oversized solute atoms. (2) Oversized solutes can act as strong trapping sites for interstitials. The larger the solute atomic volume factor, the stronger the trapping force. This leads to a more significantly sluggish interstitial migration and smaller dislocation loop size. The average dislocation loop size in Ni-20Fe was four times larger than Ni-20Pd (atomic volume factor being 10.6% and 41.3%) but an order of magnitude lower in density. The smaller dislocation loop size in Ni-20Cr is attributed to stronger interstitial binding of Cr-Ni. In conclusion, overall, the alloying effect on defects is more significant in concentrated binary alloys than in dilute binary alloys, due to the concentration difference of alloying atoms and the interstitial dominant migration mechanisms in the main irradiated region.

36 MATERIALS SCIENCE↗

GeV ion irradiation of NiFe and NiCo: Insights from MD simulations and experiments

Concentrated solid solution alloys have attracted rapidly increasing attention due to their potential for designing materials with high tolerance to radiation damage. To tackle the effects of chemical complexity in defect dynamics and radiation response, we present in this paper a computational study on swift heavy ion induced effects in Ni and equiatomic Ni -based alloys (Ni 50 Fe 50 , Ni 50 Co 50 ) using two-temperature molecular dynamics simulations (2T-MD). The electronic heat conductivity in the two-temperature equations is parameterized from the results of first principles electronic structure calculations. A bismuth ion (1.542 GeV) is selected and single impact simulations performed in each target. We study the heat flow in the electronic subsystem and show that alloying Ni with Co or Fe reduces the heat dissipation from the impact by the electronic subsystem. Simulation results suggest no melting or residual damage in pure Ni while a cylindrical region melts along the ion propagation path in the alloys. In Ni 50 Co 50 the damage consists of a dislocation loop structure (d = 2 nm) and isolated point defects, while in Ni 50 Fe 50 , a defect cluster (d = 4 nm) along the ion path is, in addition, formed. The simulation results are supported by atomic-level structural and defect characterizations in bismuth-irradiated Ni and Ni 50 Fe 50 . Finally, the significance of the 2T-MD model is demonstrated by comparing the results to those obtained with an instantaneous energy deposition model without consideration of e-ph interactions in pure Ni and by showing that it leads to a different qualitative behavior.

36 MATERIALS SCIENCE↗

Evolution of ion damage at 773K in Ni- containing concentrated solid-solution alloys

Quantitative analysis of the impact of the compositional complexity in a series of Ni-containing concentrated solid-solution alloys, Ni, NiCo, NiFe, NiCoCr, NiCoFeCr, NiCoFeCrMn and NiCoFeCrPd, on the evolution of defects produced by 1 MeV Kr ion irradiation at 773 K is reported in this paper. The dynamics of the evolution of the damage structure during irradiation to a dose of 2 displacements per atom were observed directly by performing the ion irradiations in electron transparent foils in a transmission electron microscope coupled to an ion accelerator. The defect evolution was assessed through measurement of the defect density, defect size and fraction of perfect and Frank loops. These three parameters were dependent on the alloying element as well as the number of elements. The population of loops was sensitive to the ion dose and alloy composition as faulted Frank loops were observed to unfault to perfect loops with increasing ion dose. Finally, these dependences are explained in terms of the influence of each element on the lifetime of the displacement cascade as well as on defect formation and migration energies.

36 MATERIALS SCIENCE↗

Improvement of mechanical behaviors of a superlight Mg-Li base alloy by duplex phases and fine precipitates

Limitations of strength and formability are the major obstacles to the industrial application of magnesium alloys. Here, we demonstrate, by producing the duplex phases and fine intermetallic particles in composition-optimized superlight Mg-Li-Al alloys, a unique approach to simultaneously improve the comprehensive mechanical properties (a strength-ductility balance). In conclusion, the phase components and microstructures, including the size, morphology, and distribution of precipitated-intermetallic particles can be optimized by tuning the Li content, which strongly influences the work-hardening behavior and tension-compression yield asymmetry.

36 MATERIALS SCIENCE↗

Microstructural control of FeCrAl alloys using Mo and Nb additions

The effects of Mo and Nb additions on the microstructure and mechanical properties of two FeCrAl alloys were studied in this paper. Fine and uniform recrystallized grain structures (~ 20–30 μm) were achieved in both alloys through suitable annealing after warm-rolling. The formation of Fe 2 Nb-type Laves phase precipitates in the Nb-containing FeCrAl alloy effectively stabilized the deformed and recrystallized microstructures. The Mo-containing FeCrAl alloy exhibited strong γ texture fiber after annealing at 650–900 °C, whereas the annealed Nb-containing FeCrAl alloy had much weaker texture. Finally, both strength and ductility decreased as the grain size increased in both alloys.

36 MATERIALS SCIENCE↗

Phase stability, physical properties and strengthening mechanisms of concentrated solid solution alloys

Here, we review recent research developments in a special class of multicomponent concentrated solid solution alloys (CSAs) – of which the recently discovered high entropy alloys (HEAs) are exemplars – that offer a new paradigm for the development of next generation structural materials. This review focuses on the role of inherent extreme chemical complexity on the phase stability, electronic, transport, and mechanical properties of this remarkable class of disordered solid solution alloys. Both experimental observations and theoretical models indicate that the phase stability of HEAs goes beyond the original conjecture that these alloys are stabilized by configurational/mixing entropy; rather, it results from competition between the homogeneously disordered phase and phase separation/intermetallic compound formation. Although the number of single-phase HEAs with equiatomic composition is limited, those that do exist often exhibit remarkable electronic, magnetic, transport, and mechanical properties. For the mechanical response, we discuss the solution strengthening mechanism which governs the strength and deformation behaviors of the CSAs, as well as the increasing evidence that low stacking fault energies (deformation twinning) plays an important role in the low temperature strength and ductility of CrMnFeCoNi related alloys. We also review the current understanding of the role of the number and type of alloy elements in determining the electronic, magnetic, and transport properties, in particular the dominant role of magnetic interactions in the properties of 3d-transition metal based alloys. Finally, we emphasize that, despite rapid progress in characterization and understanding of the phase stability and physical/mechanical responses of CSAs, there remain significant challenges to fully exploring the new paradigm that these alloys represent.

36 MATERIALS SCIENCE↗

Probing elastically or plastically induced structural heterogeneities in bulk metallic glasses by nanoindentation pop-in tests

Shear banding dynamics in bulk metallic glasses (BMGs) is manifested by the spatiotemporal evolution of strain fields which in turn depend on structural heterogeneities. The spacing of these heterogeneities, as a characteristic length scale, was determined from the analysis of nanoindentation pop-in tests using a stochastic model. Furthermore, the pre-stress by elastic bending and residual stress by plastic bending of BMG plates were found to dramatically decrease such spacings, thus increasing heterogeneity density and mechanically rejuvenating the glass structure.

36 MATERIALS SCIENCE↗

Understanding of the Elemental Diffusion Behavior in Concentrated Solid Solution Alloys

As one of the core effects on the high-temperature structural stability, the so-called “sluggish diffusion effect” in high-entropy alloy (HEA) has attracted much attention. Experimental investigations on the diffusion kinetics have been carried out in a few HEA systems, such as Al-Co-Cr-Fe-Ni and Co-Cr-Fe-Mn-Ni. However, the mechanisms behind this effect remain unclear. To better understand the diffusion kinetics of the HEAs, a combined computational/experimental approach is employed in the current study. In the present work, a self-consistent atomic mobility database is developed for the face-centered cubic (fcc) phase of the Co-Cr-Fe-Mn-Ni quinary system. The simulated diffusion coefficients and concentration profiles using this database can well describe the experimental data both from this work and the literatures. The validated mobility database is then used to calculate the tracer diffusion coefficients of Ni in the subsystems of the Co-Cr-Fe-Mn-Ni system with equiatomic ratios. The comparisons of these calculated diffusion coefficients reveal that the diffusion of Ni is not inevitably more sluggish with increasing number of components in the subsystem even with homologous temperature. Taking advantage of computational thermodynamics, the diffusivities of alloying elements with composition and/or temperature are also calculated. Furthermore, these calculations provide us an overall picture of the diffusion kinetics within the Co-Cr-Fe-Mn-Ni system.

36 MATERIALS SCIENCE↗

Evolution of irradiation-induced strain in an equiatomic NiFe alloy

Here, we investigate the formation and accumulation of irradiation-induced atomic strain in an equiatomic NiFe concentrated solid-solution alloy using both atomistic simulations and x-ray diffraction (XRD) analysis of irradiated samples. Experimentally, the irradiations are performed using 1.5 MeV Ni ions to fluences ranging from 1 × 10 13 to 1 × 10 14 cm -2 . The irradiation simulations are carried out by overlapping 5 keV Ni recoils cascades up to a total of 300 recoils. An increase of volumetric strain is observed at low dose, which is associated with production of point defects and small clusters. A relaxation of strain occurs at higher doses, when large defect clusters, like dislocation loops, dominate.

36 MATERIALS SCIENCE↗

Quantum critical behavior in the asymptotic limit of high disorder in the medium entropy alloy NiCoCr 0.8

The behavior of matter near a quantum critical point is one of the most exciting and challenging areas of physics research. Emergent phenomena such as high-temperature superconductivity are linked to the proximity to a quantum critical point. Although significant progress has been made in understanding quantum critical behavior in some low dimensional magnetic insulators, the situation in metallic systems is much less clear. Here, we demonstrate that NiCoCr x single crystal alloys are remarkable model systems for investigating quantum critical point physics in a metallic environment. For NiCoCr x alloys with x ≈ 0.8, the critical exponents associated with a ferromagnetic quantum critical point are experimentally determined from low temperature magnetization and heat capacity measurements. All of the five exponents (γ T ≈ 1/2, β T ≈ 1, δ ≈ 3/2, νz m ≈ 2, α¯ T ≈ 0) are in remarkable agreement with predictions of Belitz–Kirkpatrick–Vojta theory in the asymptotic limit of high disorder. Using these critical exponents, excellent scaling of the magnetization data is demonstrated with no adjustable parameters. We also find a divergence of the magnetic Gruneisen parameter, consistent with a ferromagnetic quantum critical point. This work furthermore demonstrates that entropy stabilized concentrated solid solutions represent a unique platform to study quantum critical behavior in a highly tunable class of materials.

36 MATERIALS SCIENCE↗