Search NASA⌕ Search

Engineering topics

Bender, R. L.

Publications and source records attributed to Bender, R. L..

9 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

Ares I-X Ascent Base Environments

Plume induced base heating environments were measured during the flight of the NASA Constellation Ares I-X developmental launch vehicle, successfully flown on October 28, 2009. The Ares IX first stage is a four segment Space Shuttle derived booster with base consisting of a flared aft skirt, deceleration and tumble motors, and a thermal curtain surrounding the first stage 7.2 area ratio nozzle. Developmental Flight Instrumentation (DFI) consisted of radiometers, calorimeters, pressure transducers and gas temperature probes installed on the aft skirt and nozzle to measure the base environments. In addition, thermocouples were also installed between the layers of the flexible thermal curtain to provide insight into the curtain response to the base environments and to assist in understanding curtain failure during reentry. Plume radiation environment predictions were generated by the Reverse Monte Carlo (RMC) code and the convective base heating predictions utilized heritage MSFC empirical methods. These predictions were compared to the DFI data and results from the flight videography. Radiation predictions agreed with the flight measured data early in flight but gauge failures prevented high altitude comparisons. The convective environment comparisons demonstrated the need to improve the prediction methodology; particularly for low altitude, local plume recirculation. The convective comparisons showed relatively good agreement at altitudes greater than 50,000 feet.

Mobley, B. L.↗
NASA NTRS1991

SRB Environment Evaluation and Analysis. Volume 3: ASRB Plume Induced Environments

Contract NAS8-37891 was expanded in late 1989 to initiate analysis of Shuttle plume induced environments as a result of the substitution of the Advanced Solid Rocket Booster (ASRB) for the Redesigned Solid Rocket Booster (RSRB). To support this analysis, REMTECH became involved in subscale and full-scale solid rocket motor test programs which further expanded the scope of work. Later contract modifications included additional tasks to produce initial design cycle environments and to specify development flight instrumentation. Volume 3 of the final report describes these analyses and contains a summary of reports resulting from various studies.

Bender, R. L.↗
NASA NTRS1984

Boundary layer simulator improvement

High chamber pressure expander cycles proposed for orbit transfer vehicles depend primarily on the heat energy transmitted from the combustion products through the thrust wall chamber wall. The heat transfer to the nozzle wall is affected by such variables as wall roughness, relamarization, and the presence of particles in the flow. Motor performance loss for these nozzles with thick boundary layers is inaccurate using the existing procedure coded BLIMPJ. Modifications and innovations to the code are examined. Updated routines are listed.

Praharaj, S. C.↗
NASA NTRS1983

Calculation of Shuttle Base Heating Environments and Comparison with Flight Data

The techniques, analytical tools, and experimental programs used initially to generate and later to improve and validate the Shuttle base heating design environments are discussed. In general, the measured base heating environments for STS-1 through STS-5 were in good agreement with the preflight predictions. However, some changes were made in the methodology after reviewing the flight data. The flight data is described, preflight predictions are compared with the flight data, and improvements in the prediction methodology based on the data are discussed.

Greenwood, T. F.↗
NASA NTRS1983

Space Shuttle base heating

First-stage and second-stage heating environments of the base region of the Space Shuttle are characterized in detail in terms of Orbiter-main-engine-plume and booster-plume radiation, freestream-air convective cooling, and reversed-plume-flow convective heating as they affect each base-region design point. Design predictions are compared with selected heating-rate data from flights STS-1 through STS-5; the flight data are found to show excellent interflight repeatability independent of small changes in trajectory, and to verify the validity of the prediction methodology. The impact of individual flight events on base heating is indicated.

Greenwood, T. F.↗
NASA NTRS1972

Saturn base heating handbook

A handbook containing a summary of model and flight test base heating data from the S-1, S-1B, S-4, S-1C, and S-2 stages is presented. A review of the available prediction methods is included. Experimental data are provided to make the handbook a single source of Saturn base heating data which can be used for preliminary base heating design predictions of launch vehicles.

Mullen, C. R.↗