Search NASA⌕ Search

Engineering topics

Bent, Stacey F.

Publications and source records attributed to Bent, Stacey F..

At least 19 records

Dynamics of precatalyst conversion and iron incorporation in nickel-based alkaline oxygen evolution reaction catalysts

The efficiency of alkaline water electrolyzers is limited by the oxygen evolution reaction (OER). The design of improved OER catalysts requires understanding of material changes induced by the electrolyte under oxidizing potentials. We compare four Ni-based thin-film precatalysts—Ni, NiO, Ni(OH) 2 , and NiS x —in 0.1 M KOH with and without Fe impurities. Precatalyst conversion to the active oxyhydroxide catalysts and their OER performance are induced and followed using cyclic voltammetry. Without Fe electrolyte impurities, the precatalysts convert at different rates to a similar, modestly active NiOOH catalyst. Added Fe impurities are incorporated concurrently with the oxyhydroxide formation leading to active Ni 1-x Fe x OOH catalysts. The NiS x and Ni(OH) 2 precatalysts rapidly convert to oxyhydroxides both with and without Fe, while conversion of Ni and especially NiO is slowed down by Fe impurities. Choice of the precatalyst and presence of Fe impurities are key factors in designing active Ni 1-x Fe x OOH OER catalysts for electrolyzers.

alkaline electrolysis↗

Deconvoluting Effects of Lithium Morphology and SEI Stability at Moderate Current Density Using Interface Engineering

Lithium (Li)-morphology and solid electrolyte interphase (SEI) are among the most significant performance regulators in Li-metal batteries (LMBs). While both Li-morphology and SEI composition play key roles in the cyclability of LMBs, less is understood about the individual contributions of each factor to overall Li reversibility, particularly at a practical current density (1 mA cm −2 ) at which the kinetics of both factors are not naturally separated. Herein, an interface engineering approach is introduced to deconvolute the impacts of Li-morphology and SEI composition on battery performance. By using interfacial nanofilms with differing resistivity (resistive HfO 2 versus conductive ZnO), the morphology of Li is varied, and by virtue of similar acidic character of the nanofilms, the formation of anion-rich SEIs is maintained. It is established that although the surface acidity of the thin films enables preformation of a more anion-rich SEI, it is not preserved after Li plating. It is further shown that resistance-controlled, low-surface-area Li-morphology exhibits up to threefold increase in stable cycle life when tested in multiple electrolytes. Overall, these findings explain why Li-morphological control is more advantageous for performance improvement than preformed SEI modulation due to the inherent challenges in SEI preservation.

36 MATERIALS SCIENCE↗

Unveiling the Stability of Encapsulated Pt Catalysts Using Nanocrystals and Atomic Layer Deposition

Platinum exhibits desirable catalytic properties, but it is scarce and expensive. Optimizing its use in key applications such as emission control catalysis is important to reduce our reliance on such a rare element. Supported Pt nanoparticles (NPs) used in emission control systems deactivate over time because of particle growth in sintering processes. Here, in this work, we shed light on the stability against sintering of Pt NPs supported on and encapsulated in Al 2 O 3 using a combination of nanocrystal catalysts and atomic layer deposition (ALD) techniques. We find that small amounts of alumina overlayers created by ALD on preformed Pt NPs can stabilize supported Pt catalysts, significantly reducing deactivation caused by sintering, as previously observed by others. Combining theoretical and experimental insights, we correlate this behavior to the decreased propensity of oxidized Pt species to undergo Ostwald ripening phenomena because of the physical barrier imposed by the alumina overlayers. Furthermore, we find that highly stable catalysts can present an abundance of under-coordinated Pt sites after restructuring of both Pt particles and alumina overlayers at a high temperature (800 °C) in C 3 H 6 oxidation conditions. The enhanced stability significantly improves the Pt utilization efficiency after accelerated aging treatments, with encapsulated Pt catalysts reaching reaction rates more than two times greater than those of a control supported Pt catalyst.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Dissolution of the Solid Electrolyte Interphase and Its Effects on Lithium Metal Anode Cyclability

At >95% Coulombic efficiencies, most of the capacity loss for Li metal anodes (LMAs) is through the formation and growth of the solid electrolyte interphase (SEI). However, the mechanism through which this happens remains unclear. One property of the SEI that directly affects its formation and growth is the SEI’s solubility in the electrolyte. Here, in this work, we systematically quantify and compare the solubility of SEIs derived from ether-based electrolytes optimized for LMAs using in-operando electrochemical quartz crystal microbalance (EQCM). A correlation among solubility, passivity, and cyclability established in this work reveals that SEI dissolution is a major contributor to the differences in passivity and electrochemical performance among battery electrolytes. Together with our EQCM, X-ray photoelectron spectroscopy (XPS), and nuclear magnetic resonance (NMR) spectroscopy results, we show that solubility depends on not only the SEI’s composition but also the properties of the electrolyte. This provides a crucial piece of information that could help minimize capacity loss due to SEI formation and growth during battery cycling and aging.

25 ENERGY STORAGE↗

Data-driven electrolyte design for lithium metal anodes

Improving Coulombic efficiency (CE) is key to the adoption of high energy density lithium metal batteries. Liquid electrolyte engineering has emerged as a promising strategy for improving the CE of lithium metal batteries, but its complexity renders the performance prediction and design of electrolytes challenging. Here, we develop machine learning (ML) models that assist and accelerate the design of high-performance electrolytes. Using the elemental composition of electrolytes as the features of our models, we apply linear regression, random forest, and bagging models to identify the critical features for predicting CE. Our models reveal that a reduction in the solvent oxygen content is critical for superior CE. We use the ML models to design electrolyte formulations with fluorine-free solvents that achieve a high CE of 99.70%. This work highlights the promise of data-driven approaches that can accelerate the design of high-performance electrolytes for lithium metal batteries.

25 ENERGY STORAGE↗

Surface Fe clusters promote syngas reaction to oxygenates on Rh catalysts modified by atomic layer deposition

Converting syngas to higher oxygenates is a promising strategy for sustainably producing fuels and chemicals used every day. Rh-based catalysts promoted with metal oxides have long been of interest for oxygenate synthesis, but the role of promoters and the structure of the catalyst during reaction are often not well understood. In this work, we characterize a Rh/SiO 2 catalyst modified by Fe 2 O 3 deposited by atomic layer deposition (ALD). Here, we show that Fe 2 O 3 deposits selectively on the Rh nanoparticles and enhances both the turnover frequency and the oxygenate selectivity of the catalysts. A maximum 29% selectivity towards higher oxygenates is achieved with just 1 cycle of Fe 2 O 3 ALD, and we relate the trends in selectivity to the changing availability of surface sites that drive higher alcohol (e.g., ethanol and propanol) formation. Further, we show that the ALD promoter mitigates catalyst sintering, improving the stability of these materials. In-situ X-ray absorption spectroscopy experiments reveal that the Fe 2 O 3 undergoes reduction during the catalyst pretreatment and forms Fe clusters on the surface of the Rh that migrate but remain stable under syngas reaction conditions. We find that modification of the Rh with these surface Fe species is key to the enhanced alcohol production observed in these materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Solar cell comprising a metal-oxide buffer layer and method of fabrication

A perovskite-based solar cell comprising a transparent electrode disposed on a buffer layer that protects the perovskite from damage during the deposition of the electrode is disclosed. The buffer material is deposited using either low-temperature atomic-layer deposition, chemical-vapor deposition, or pulsed chemical-vapor deposition. In some embodiments, the perovskite material is operative as an absorption layer in a multi-cell solar-cell structure. In some embodiments, the perovskite material is operative as an absorption layer in a single junction solar cell structure.

Bush, Kevin Alexander↗

Steering CO 2 hydrogenation toward C–C coupling to hydrocarbons using porous organic polymer/metal interfaces

The conversion of CO 2 into fuels and chemicals is an attractive option for mitigating CO 2 emissions. Controlling the selectivity of this process is beneficial to produce desirable liquid fuels, but C–C coupling is a limiting step in the reaction that requires high pressures. Here, we propose a strategy to favor C–C coupling on a supported Ru/TiO 2 catalyst by encapsulating it within the polymer layers of an imine-based porous organic polymer that controls its selectivity. Such polymer confinement modifies the CO 2 hydrogenation behavior of the Ru surface, significantly enhancing the C 2+ production turnover frequency by 10-fold. We demonstrate that the polymer layers affect the adsorption of reactants and intermediates while being stable under the demanding reaction conditions. Our findings highlight the promising opportunity of using polymer/metal interfaces for the rational engineering of active sites and as a general tool for controlling selective transformations in supported catalyst systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Suspension electrolyte with modified Li + solvation environment for lithium metal batteries

Designing a stable solid–electrolyte interphase on a Li anode is imperative to developing reliable Li metal batteries. In this work, we report a suspension electrolyte design that modifies the Li + solvation environment in liquid electrolytes and creates inorganic-rich solid–electrolyte interphases on Li. Li 2 O nanoparticles suspended in liquid electrolytes were investigated as a proof of concept. Through theoretical and empirical analyses of Li 2 O suspension electrolytes, the roles played by Li 2 O in the liquid electrolyte and solid–electrolyte interphases of the Li anode are elucidated. Also, the suspension electrolyte design is applied in conventional and state-of-the-art high-performance electrolytes to demonstrate its applicability. Based on electrochemical analyses, improved Coulombic efficiency (up to ~99.7%), reduced Li nucleation overpotential, stabilized Li interphases and prolonged cycle life of anode-free cells (~70 cycles at 80% of initial capacity) were achieved with the suspension electrolytes. We expect this design principle and our findings to be expanded into developing electrolytes and solid–electrolyte interphases for Li metal batteries.

25 ENERGY STORAGE↗

Rational solvent molecule tuning for high-performance lithium metal battery electrolytes

Electrolyte engineering improved cycling of Li metal batteries and anode-free cells at low current densities; however, high-rate capability and tuning of ionic conduction in electrolytes are desirable yet less-studied. In this study, we design and synthesize a family of fluorinated-1,2-diethoxyethanes as electrolyte solvents. The position and amount of F atoms functionalized on 1,2-diethoxyethane were found to greatly affect electrolyte performance. Partially fluorinated, locally polar –CHF 2 is identified as the optimal group rather than fully fluorinated –CF 3 in common designs. Paired with 1.2 M lithium bis(fluorosulfonyl)imide, these developed single-salt-single-solvent electrolytes simultaneously enable high conductivity, low and stable overpotential, >99.5% Li||Cu half-cell efficiency (up to 99.9%, ±0.1% fluctuation) and fast activation (Li efficiency >99.3% within two cycles). Combined with high-voltage stability, these electrolytes achieve roughly 270 cycles in 50-μm-thin Li||high-loading-NMC811 full batteries and >140 cycles in fast-cycling Cu||microparticle-LiFePO 4 industrial pouch cells under realistic testing conditions. The correlation of Li + –solvent coordination, solvation environments and battery performance is investigated to understand structure–property relationships.

25 ENERGY STORAGE↗

The Importance of Decarbonylation Mechanisms in the Atomic Layer Deposition of High-Quality Ru Films by Zero-Oxidation State Ru(DMBD)(CO) 3

Achieving facile nucleation of noble metal films through atomic layer deposition (ALD) is extremely challenging. To this end, η 4 -2,3-dimethylbutadiene ruthenium tricarbonyl (Ru(DMBD)(CO) 3 ), a zero-valent complex, has recently been reported to achieve good nucleation by ALD at relatively low temperatures and mild reaction conditions. Here, we study the growth mechanism of this precursor by in situ quartz-crystal microbalance and quadrupole mass spectrometry during Ru ALD, complemented by ex situ film characterization and kinetic modeling. These studies reveal that Ru(DMBD)(CO) 3 produces high-quality Ru films with excellent nucleation properties. This results in smooth, coalesced films even at low film thicknesses, all important traits for device applications. However, Ru deposition follows a kinetically limited decarbonylation reaction scheme, akin to typical CVD processes, with a strong dependence on both temperature and reaction timescale. The non-self-limiting nature of the kinetically driven mechanism presents both challenges for ALD implementation and opportunities for process tuning. By surveying reports of similar precursors, we suggest that the findings can be generalized to the broader class of zero-oxidation state carbonyl-based precursors used in thermal ALD, with insight into the design of effective saturation studies.

chemical vapor deposition↗

Modulating the optoelectronic properties of hybrid Mo-thiolate thin films

In this study, hybrid MoS 2 -based molybdenum thiolate thin films with selected organic motifs are grown using molecular layer deposition (MLD), allowing for tunable optoelectronic film properties. The thin films are deposited at 170°C using the metal precursor molybdenum hexacarbonyl and one of the three organic precursors: 1,2-ethanedithiol, 1,4-butanedithiol, and 1,4-benzenedithiol. The resulting Mo-ethanethiolate, Mo-butanethiolate, and Mo-benzenethiolate films show saturating growth with a growth per cycle of 1.2, 1.0, and 1.5 Å/cycle, respectively. Fourier transform infrared spectroscopy, x-ray photoelectron spectroscopy, Raman spectroscopy, x-ray absorption spectroscopy, and x-ray diffraction are used to characterize the as-deposited films. Results show that by changing the organic precursor, the film composition as well as the optical and electronic properties can be tuned. The Mo-thiolate films grown with benzenedithiol exhibit the lowest resistivity, which at 12 mΩ cm is ~400 times more conductive than Mo-thiolates grown with aliphatic organic linkers. All three backbone chemistries of the Mo-thiolates show an optical bandgap between 2.3 and 2.4 eV and mild photoconductivity response. The MLD of these Mo-thiolate films demonstrates the synthesis of transition metal-organosulfur thin films with tunable properties.

36 MATERIALS SCIENCE↗

Impurity Control in Catalyst Design: The Role of Sodium in Promoting and Stabilizing Co and Co 2 C for Syngas Conversion

The design of supported heterogeneous catalysts requires a detailed understanding of the structure and chemistry of the active surface. Although the chemical components of the active phase, support material, and process feed are typically considered to be the most important factors governing catalyst structure and performance, many common commercial supports contain trace impurities, which can have profound effects on catalyst properties. In this work, we study silica–supported cobalt–based catalysts, which are widely used in syngas conversion to value–added products. Supported metallic Co is a commercial Fischer–Tropsch catalyst, whereas Co 2 C has shown promise for the direct conversion of syngas to higher oxygenates. This study examines the effects of Na, a commonly detected support impurity and a frequently used promoter, on the structure and reactivity of Co and Co 2 C. We show that trace Na impurities significantly decrease catalyst activity of supported metallic Co, and that high Na concentrations result in Co 2 C formation and a loss in Fischer–Tropsch activity. However, in Co 2 C catalysts, Na plays an important role in stabilizing the Co 2 C phase, but excess Na decreases catalyst activity. We use insitu X–ray absorption spectroscopy to study Co 2 C formation and decomposition in the Na–free catalyst under carburization and reaction conditions. Lastly, the work reveals the importance of carefully controlling alkali metal content, particularly at trace levels, in catalyst design.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Identifying higher oxygenate synthesis sites in Cu catalysts promoted and stabilized by atomic layer deposited Fe 2 O 3

The conversion of syngas to higher oxygenates is an important step in the pathway towards the long-term sustainable production of fuels and chemicals. Mixed Cu/Fe catalysts combine metals with different CO activation characteristics, a property that makes them promising candidates for higher oxygenate production. However, Cu/Fe catalysts suffer from instability due to sintering and phase separation, and the active sites for higher oxygenate formation on these materials are not well understood. In this work, we use atomic layer deposition (ALD) to modify silica-supported Cu nanoparticles with monolayer precise amounts of Fe 2 O 3 and study the effects on catalyst structure, reactivity, and stability. We demonstrate that the Fe 2 O 3 ALD process is inherently selective towards deposition on the SiO 2 surface versus the Cu nanoparticles. As a result, a sufficiently thick Fe 2 O 3 layer surrounding the Cu nanoparticles acts as a barrier against Cu migration, preventing catalyst deactivation through sintering without covering the Cu. In syngas conversion reactions, we find that higher oxygenate selectivity increases with Fe 2 O 3 loading at low and intermediate ALD cycle numbers. Furthermore, using in situ X-ray absorption spectroscopy, we demonstrate that the Fe near the Cu nanoparticles is reduced to a metallic state under reaction conditions. From these measurements, we identify these metallic Cu/Fe interfaces as the active sites for higher oxygenate formation, which are most abundant at intermediate Fe 2 O 3 ALD cycle numbers. As the Fe 2 O 3 loading increases, higher oxygenate selectivity falls, resulting from encapsulation of the Cu nanoparticles by thick Fe 2 O 3 layers. Overall, the results demonstrate how thickness-controlled ALD Fe 2 O 3 can be used as both a promoter and stabilizer of Cu-based higher oxygenate synthesis catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterizing Self-Assembled Monolayer Breakdown in Area-Selective Atomic Layer Deposition

In order to enable area-selective atomic layer deposition (AS-ALD), self-assembled monolayers (SAMs) have been used as the surface inhibitor to block a variety of ALD processes. The integrity of the SAM throughout the ALD process is critical to AS-ALD. Despite the demonstrated effectiveness of inhibition by SAMs, nucleation during ALD eventually occurs on SAM-protected surfaces, but its impact on SAM structures is still not fully understood. In this study, we chose the octadecyltrichlorosilane (ODTS) SAM as a model system to investigate the evolution of crystallinity and structure of SAMs before and after ALD. The breakdown behavior of SAMs when exposed to ZnO and Al 2 O 3 ALD was systematically studied by combining synchrotron X-ray techniques and electron microscopy. We show that the crystallinity and structure of ODTS SAMs grown on Si substrates remain intact until a significant amount of material deposition takes place. In addition, the undesired ALD materials that grow on ODTS SAMs present contrasting morphologies: dispersed nanoparticles for ZnO while relatively continuous film for Al 2 O 3 . Lastly, substrate dependency was explored by comparing a Si substrate to single-crystal sapphire. Similar results in the evolution of SAM crystallinity and formation of ALD nuclei on top of SAM are observed in the ODTS–sapphire system. This study provides an in-depth view of the influence of ALD processes on the SAM structure and the nucleation behavior of ALD on SAM-protected surfaces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Monolayer Support Control and Precise Colloidal Nanocrystals Demonstrate Metal-Support Interactions in Heterogeneous Catalysts

We report that electronic and geometric interactions between active and support phases are critical in determining the activity of heterogeneous catalysts, but metal-support interactions are challenging to study. Here, it is demonstrated how the combination of the monolayer-controlled formation using atomic layer deposition (ALD) and colloidal nanocrystal synthesis methods leads to catalysts with sub-nanometer precision of active and support phases, thus allowing for the study of the metal-support inter-actions in detail. The use of this approach in developing a fundamental understanding of support effects in Pd-catalyzed methane combustion is demonstrated. Uniform Pd nanocrystals are deposited onto Al2O 3 /SiO 2 spherical supports prepared with control over morphology and Al 2 O 3 layer thicknesses ranging from sub-monolayer to a ≈4 nm thick uniform coating. Dramatic changes in catalytic activity depending on the coverage and structure of Al 2 O 3 situated at the Pd/Al 2 O 3 interface are observed, with even a single monolayer of alumina contributing an order of magnitude increase in reaction rate. By building the Pd/Al 2 O 3 interface up layer-by-layer and using uniform Pd nanocrystals, this work demonstrates the importance of controlled and tunable materials in determining metal-support interactions and catalyst activity.

36 MATERIALS SCIENCE↗

Tailoring the Surface of Metal Halide Perovskites to Enable the Atomic Layer Deposition of Metal Oxide Contacts

Replacing organic contact layers with inorganic counterparts, such as metal oxides, is one strategy for improving long-term device stability in metal halide perovskite solar cells. Often, the methods used to deposit metal oxide thin films are incompatible with metal halide perovskites, creating challenges for the fabrication of contacts above the perovskite absorber layer. In this study, we utilize a one-step, solution treatment of the top surface of Cs 0.25 FA 0.75 Pb(Br 0.20 I 0.80 ) 3 to create a thin (~1 nm) overlayer of lead sulfide (PbS) to protect the underlying perovskite during subsequent deposition. X-ray characterization of the surface region shows that the PbS overlayer limits undesirable changes to the perovskite structure and stoichiometry during atomic layer deposition (ALD) of SnO 2 . This protection enables ALD growth of SnO 2 electron contacts on top of the perovskite without an organic transport layer (e.g., C 60 ), resulting in a solar cell with a power conversion efficiency of 5.8%. This result is a marked improvement over devices with ALD SnO 2 grown directly on the perovskite without a PbS overlayer, which produce no power output. Furthermore, the interface characterization and device results in this study highlight some of the key challenges associated with ALD metal oxide growth on perovskite materials and can help inform the future design of inorganic contact layer deposition in solar photovoltaic technologies.

36 MATERIALS SCIENCE↗