Search NASA⌕ Search

Engineering topics

Bosco, Nick

Publications and source records attributed to Bosco, Nick.

At least 37 records · Page 2

Environmental Influence on Fracture and Delamination of Electrically Conductive Adhesives

This paper presents our continued work on developing a degradation model for electrically conductive adhesive (ECA) interconnects in photovoltaic modules. Here, we characterize the fracture mechanics properties of an epoxy based ECA, for both critical and subcritical loading conditions. Emphasis is put on the influence of different environmental conditions such as temperature and humidity. We found that high levels of humidity not only weaken the adhesive joint but also promote subcritical debonding at significantly lower driving forces than in dry environments.

41 EE - Solar Energy Technologies Office (EE-4S)↗

Employing Fracture Statistics to Track Cell Reliability Through Module Fabrication

In this work we demonstrate how fracture statistics may be employed to track cell reliability through module fabrication steps. We were able to detect how cell cutting equipment could reduce cell fracture strain by 25 % as well as increase its variability. A smaller reduction was found to result from the ribbon soldering operation, and all cells measured were weaker when strained in an orientation perpendicular to the gridlines. Cell fracture measurements were found to be consistent with the number of cracked cells experienced in full sized modules exposed to mechanical loading. A structural mechanics model was created to elucidate how the requisite fracture strain is developed in a cell encapsulated within a PV module and demonstrates that this strain decreases more than 50 % from its center to edge when placed within the inner loading span of four-point flexure. The associated implications on the apparent cell strength is examined with an effective volume treatment.

41 EE - Solar Energy Technologies Office (EE-4S)↗

Fatigue-Like Behavior of Silver Metallization Gridlines and Proposed Damage Mechanics Model

In this work, we present a novel method to evaluate the fracture and fatigue-like behavior of crystalline silicon PV cell metallization. Initial results demonstrate that silver metal gridlines are capable of bridging a ~10–20 µm gap prior to becoming electrically open and do demonstrate fatigue-like behavior under cyclic straining conditions. This later phenomenon was well fit with a traditional power law equation for high cycle fatigue and enabled the development of a damage mechanics model for gridline failure.

41 EE - Solar Energy Technologies Office (EE-4S)↗

Improving Computational Efficiency of Mechanical Finite Element Method Simulations for PV Modules: Preprint

In this work we have elucidated the trade off between structural mechanics FEM model accuracy and computation time by employing lower fidelity viscoelastic models. Results indicate that computation time can easily be cut in half while only expecting a potential maximum error of 10 % by considering lower fidelity models. A novel approach to produce the Prony Series fit for viscoelastic characterization has also been presented. Employing this approach, we were able to achieve a further 10 % reduction in computation time without further sacrificing simulation accuracy.

41 EE - Solar Energy Technologies Office (EE-4S)↗

Viscoelastic Material Characterization and Modeling of Photovoltaic Module Packaging Materials for Direct Finite-Element Method Input

Numerical tools, such as the finite-element method, are increasingly used to design and evaluate the photovoltaic (PV) modules, providing for the reduction of development time and improved performance and reliability. However, high-fidelity material models are necessary to accurately model the complex structural behavior of the involved packaging materials. A common simplification used in recent years is to model the polymer materials (i.e., encapsulant and backsheet) as linear elastic, which will lead to inaccurate results. Therefore, in this work, we present a thorough characterization of the time- and temperature-dependent mechanical response of predominant PV module encapsulant and backsheet materials. Based on this material characterization, we developed and experimentally validated generalized Maxwell models to describe each material's viscoelastic response. In addition, we included measurements of the coefficient of thermal expansion and presented all material models in such a fashion for direct input into commercial finite-element method modeling software.

FEM↗

Linear viscoelastic characterization of electrically conductive adhesives used as interconnect in photovoltaic modules

Electrically conductive adhesives (ECAs) are incorporated into recent designs of photovoltaic (PV) modules and replace the traditional metallic solders as interconnects. This transition depicts a significant material change, and a proper understanding of the interconnects' mechanical response has not yet been established. However, such an understanding is necessary to (a) identify the driving forces for module degradation and failure, (b) allow for module design optimization, and (c) enable accurate lifetime predictions. This study summarizes the framework for the mechanical materials characterization and modeling of ECAs for PV applications. Only high-fidelity material models are able to capture the rate and temperature dependency of the ECA interconnect and allow for accurate modeling of the materials response. Furthermore, a linear viscoelastic representation is found to describe the mechanical response of the ECAs sufficiently well. The effects of curing conditions and environmental exposure are investigated, and material models for a variety of ECAs are reported and prepared for the use in numerical simulations. Overall, a finite element simulation of a generic submodel of a shingled cell module is used to highlight the need for high-fidelity material models and demonstrates the error made in the predicted stress states by using less sophisticated models.

14 SOLAR ENERGY↗

FTIR Investigation of EVA Chemical Bonding Environment and Its Impact on Debond Energy

The chemical makeup of ethylene vinyl acetate (EVA) interfaces in photovoltaic (PV) modules is probed via Fourier-transform infrared spectroscopy (FTIR) to determine the impact of the EVA formulation on the adhesion degradation. EVA samples laminated with glass particles are used to demonstrate the effect of damp heat exposure on the glass-EVA interface, showing that increasing silane content increases chemical stability. Delamination interfaces created in one cell modules demonstrate a high correlation between the siloxane bonding at the silicon cell-EVA interface and the debond energy. A significant decrease in debond energy after UV exposure is also shown to be due in part to decreasing siloxane bond density at the interface. However, FTIR results indicated contributions to the adhesion beyond the chemical interface, and a basic tensile test indicates increasing bulk mechanical properties with increasing silane. These results demonstrate the importance of the EVA formulation on its adhesion performance and long-term reliability. Furthermore, it is shown that FTIR is a capable technique for assessing and quantifying chemical mechanisms within PV modules. These results can then be used to more effectively model module lifetimes and to better design polymer systems for PV modules.

14 SOLAR ENERGY↗

Mechanisms of adhesion degradation at the photovoltiac module's cell metallization-encapsulant interface

Adhesion measurements and chemical characterization of the encapsulant/silver metallization interface of a photovoltaic (PV) module through temperature, humidity, and voltage bias exposures were conducted. Results demonstrate two independent degradation mechanisms: (a) with voltage bias, the ionic conduction of Na + ions through the encapsulant results in the formation of sodium silicate at the silver metallization surface, thereby weakening that interface and (b) with moisture ingress, dissociation of the silane bonding to silver in the silver oxide similarly weakens this interface resulting in significantly lower debond energies.

14 SOLAR ENERGY↗

Thermomechanical Lift-Off and Recontacting of CdTe Solar Cells

Controlled delamination of thin-film photovoltaics (PV) post-growth can reveal interfaces that are critical to device performance yet are poorly understood because of their inaccessibility within the device stack. In this work, we demonstrate a technique to lift off thin-film solar cells from their glass substrates in a clean, reproducible manner by first laminating a polymeric backsheet to the device and then thermally shocking the system at low temperatures (T ≤ -30 degrees C). To enable clean delamination of diverse thin-film architectures, a theoretical framework is developed and key process control parameters are identified. Focusing on cadmium telluride (CdTe) devices, we show that the lamination temperature and device architecture control the quality of lift-off, while the rate at which the film stack is removed is controlled by the delamination temperature. Crack-free CdTe devices are removed and successfully recontacted, recovering up to 80% of the original device efficiency. The areal density of these devices is ~0.4 kg m -2 , a reduction of over an order of magnitude relative to their initial weight on glass. The framework developed here provides a pathway toward both the development of inexpensive, flexible PV with high specific power and the study of previously buried interfaces in thin-film architectures.

14 SOLAR ENERGY↗

Evaluating and predicting molecular mechanisms of adhesive degradation during field and accelerated aging of photovoltaic modules

Extending photovoltaic (PV) module lifetimes beyond 30 years is a goal of significant priority. A challenge that must first be addressed, however, is the development of a predictive reliability model that captures the synergy of terrestrial stressors on module degradation, particularly at encapsulant interfaces. Using a metrology designed specifically for PV modules, a comprehensive study of the widely used ethylene vinyl acetate encapsulant was performed in which encapsulant adhesion was evaluated as a function of environmental stressors (UV exposure, temperature, and humidity) for modules aged both under accelerated lab and internationally located field conditions for months to nearly 3 decades. Mechanical and chemical characterization methods are combined with fundamental polymer reaction engineering to unravel the degradation processes active at the molecular scale that lead to encapsulant delamination. An analytical and modular model framework is put forward enabling the prediction of long-term PV module durability, starting from fundamental principles at the molecular level and explicitly accounting for bond rupture events in the bulk encapsulant and at the encapsulant interfaces. Successful parameter tuning to adhesion data indicates a dominant occurrence of deacetylation, β-scission, and hydrolytic depolymerization, respectively. The model contributes to the longstanding challenge of predicting module lifetimes in any geographic location while minimizing time-consuming and costly aging studies.

14 SOLAR ENERGY↗