Search NASA⌕ Search

Engineering topics

Breault, Ronald

Publications and source records attributed to Breault, Ronald.

At least 37 records · Page 2

Multiphysics Simulation of Supercritical CO2 Gasification for Hydrogen Production

A bench-scale supercritical CO2 gasifier is being considered by the U.S. Department of Energy’s National Energy Technology Laboratory (NETL). A reacting computational fluid dynamics (CFD) model was developed using ANSYS/Fluent in order to investigate the impact of various operating parameters on syngas composition. The model was validated using available data in the literature. Simulations were conducted over a range of coal-slurry loadings, reaction temperatures, system pressures, and oxygen mass flowrates with the goal of optimizing hydrogen production for the considered reactor. The results from the simulations identified a positive correlation between slurry loading and hydrogen production, while reactor temperature and pressure had a limited impact on H2 production at the conditions of interest. Additionally, the simulations indicated that oxygen mass flowrate has less of an impact on hydrogen production at higher slurry loadings.

Prlina, Alexander↗

Reduction of Ultrafine Hematite for a Spouting Bed Chemical Looping Process - Presentation

Chemical looping combustion research has been a topic of great interest since the mid-1990s, although the concept can be traced much further back. It is a combustion technology for fuel utilization that uses a two-reactor system to produce a carbon free effluent stream from the air reactor and a carbon dioxide rich stream from the fuel reactor with oxygen shuttled between the reactors with an oxygen carrier. Chemical looping combustion has been studied extensively because of this inherent separation of the carbon dioxide combustion product from the atmospheric nitrogen over that past 25 years with hundreds of research papers and tens of books. The oxygen carrier is, in general, a solid such as naturally occurring hematite or an engineered carrier like a copper and iron oxide supported on alumina. System technical and economic research activities conducted at the National Energy Technology Laboratory have shown that the costs associated with the carrier, initial and replacement, are a significant factor in the economic viability of the technology. To overcome this economic challenge, the work reported on in this paper investigates the use of a waste iron oxide as the chemical looping oxygen carrier. This waste material is quite unique as it has a particle size of 0.7 um. Given the particle size, the reactions are quite fast. However, the development of a contactor reactor to mix the fuel with the carrier is a fluidization challenge as the material is a Geldart group C material and highly cohesive. Normally, Geldart group C materials are fluidized with either a vibrating bed. This technique is acceptable for low temperature pharmaceuticals production but does not lend itself to much larger reactors used for power production or operation at temperatures in the order of 1100 to 1200 C. Therefore, a hydrodynamic solution was needed to break up the cohesive structures to replace the vibration. In this instance, it was hypothesized that a spouting bed of large Geldart group B or Geldart group D particles could provide the necessary energy to break up the cohesive structures of the Geldart group C material. This paper presents the reduction performance for this novel carrier material in a laboratory spouting bed reactor.

Breault, Ronald↗

The Development of a Generalized Riser Flow Regime Map Based Upon Higher Moment and Chaotic Statistics Using Electrical Capacitance Volume Tomography (ECVT)

Dynamic analyses have been applied to the temporal signals from an Electro Capacitance Volume Tomography instrument located near mid-height on the riser of an industrial-scale cold-flow circulating fluidized bed to characterize gas-solids flow behavior in the riser. Twelve capacitance electrodes surround the cylindrical riser over a height of 1.3 m. The instrument used a neural network deconvolution algorithm to determine the spatially resolved solids fraction recorded at 52 Hz. Experiments were carried out over a range of gas and solids flows in the transport regime using a Geldart Group B bed material, high density polyethylene with mean particle size of 880 μm. The radial solids distribution was found to vary from one-time step to the next between profiles typical of laminar and turbulent flow. The duration of time spent in each of these flow profiles depended upon the operating regime – dilute, core-annular, or fast fluidized bed. The chaotic structure of the temporal data was characterized using the three conventional approaches: the first 4 moments from the distribution of signal in time, system memory parameters from the autocorrelation function and the Hurst exponent, and analysis of the correlationentropy and correlation dimension of the attractor. These signal analysis techniques were used to clearly distinguish differences between different transport operating regimes. Specifically, it was experimentally observed that a riser transitions from core annular flow profile to dilute and dense regimes via increasing the frequency of short term transients to either dilute or dense flow profiles, respectively. A regime map was generated based upon these dynamics using solids flux and gas velocity axes. Fast fluidized, core annular, and dilute each exhibited different degree of dynamic characteristics typical of fluid dominated or particle compromising behavior. It should be noted that the magnitude for the different statistics was in the same range regardless of the regime, it was the radial profile for the statistic that changed and subsequently identified that there was a change in the regime. Finally, a reduced regime map was developed consisting of plotting the gas velocity normalized by the upper transport velocity versus the solids flux normalized by the saturation carrying capacity. The use of this reduced plot allowed the data from widely different conditions to be plotted and compared on the same<p>graph. Note that in many instances, some of the statistics identified the operating point as being in one regime while others indicated that it was in another indicating a transition region between dilute or core annular regimes and between the core annular and fast fluidization regimes. This now provides a tool that can be used to optimize process performance, identify changes in operating states, or replicate process dynamics during process scaling or changing operating parameters. </p>

Breault, Ronald↗

Operational Performance Characteristics of an Aerated L-valve Operated Within a Closed Circulating Fluidized Bed Loop

An experimental study was conducted in a large scale circulating fluidized bed (0.3 m diameter ×15.5 m tall) equipped with nonmechanical L-valve (0.25 m diameter ×1.52 m long) varying the riser superficial gas velocity (U g ), bed inventory (m), L-valve aeration velocity (U Lvalve ) and standpipe aeration velocity (U move ). The effects of these operational parameters on pressure drop were investigated in each of the different components in the CFB and on the solid circulation rate with two different Group B particles (180 μm glass bead and 750 μm phosphorescent polyethylene beads, PPE). Tests were carried out at ambient temperature and pressure conditions using air as the fluidization gas. The operating parameters were shown to significantly affect pressure drops across various sections of the CFB due to redistribution of solids within the system. The pressure drop in the horizontal section of the L-valve was affected by aeration rates in addition to the solid flow rate reported in previous studies of smaller L-valves without aeration. A new dimensionless semi-empirical correlation was able to explain > 98% of the variance between pressure drop across the horizontal section of the L-valve and operating parameters for these Group B particles. The results of present study indicated that the nonmechanical L-valve cannot be isolated from the CFB system for performance evaluation.

Monazam, Esmail R.↗